“This site contains affiliate links for which OEMDTC may be compensated” |
March 9, 2021 NHTSA CAMPAIGN NUMBER: 21V151000
Brake Lights and Tail Lights Too High/FMVSS 108
Reduced visibility of the brake and tail lights can increase the risk of a crash.
NHTSA Campaign Number: 21V151
Manufacturer Nova Bus
Components EXTERIOR LIGHTING
Potential Number of Units Affected 201
Summary
Nova Bus (Nova) is recalling certain 2008-2021 LFS Buses. The center-line height of the brake lights and tail lights is too high, exceeding the maximum height standard. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, “Lamps, Reflective Devices, and Associated Equipment.”
Remedy
Nova will notify owners, and provide instructions for interchanging the positions of the brake light and tail light components with the turn signal light components, free of charge. The recall is expected to begin May 2021. Owners may contact Nova customer service at 1-800-350-6682.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
CR5065E
PROCEDURE
LEVEL 1 ; REPOSITION STOP LAMP AND TAIL LAMPS
1.1. Remove the 3 screws retaining the street and curb side panels on the side of the vehicle. If one of the screws spins or it is hard to remove, you will need to perform the level 2 rivnut replacement procedure. See Figure 1
1.2. Remove the rear retaining screws and remove the curb side stop and flasher light corner panel. Retain the hardware. See Figure 2.
1.3. Remove the rear retaining screws and remove the street side stop and flasher light corner panel. Retain the hardware. See Figure 2.
1.4. Disconnect and remove both lights from the removed curb side corner panel. Retain the hardware.
1.5. Install the stop lamp at the bottom position and the other lamp at the top position on the removed curb side stop and flasher light panel. See Figure 3.
1.6. Disconnect and remove both lights from the removed street side panel. Retain the hardware.
1.7. Install the stop lamp at the bottom position and the other lamp at the top position on the removed street side stop and flasher light panel. See Figure 3 .
CAUTION
Position the TOP mark at the top of both lamps when fixing the lamps to the corner plates. See Figure 3.
1.8. Reconnect the lamp and reinstall the curb and street side corner panel with the retained hardware. Secure the harness with G5007996 tye rap.
LEVEL 2 : RIVNUT REPLACEMENT PROCEDURE
2.1. Remove the side panel located between the rear light corner panel and the rear side window. Retain the hardware. See Figure 4.
2.2. Remove the defective rivnut.
2.3. Install a new N71801 Rivnut.
2.4. Reinstall the removed side panel with the retained hardware. Proceed with step 1.2 of Level 1 procedure.
CR5077E
PROCEDURE
LEVEL 1 ; REPOSITION STOP LAMP AND TAIL LAMPS
1.1. Remove the 3 anchor screws retaining the street and curb side light panels. If one of the screws spins or it is hard to remove, you will need to perform the level 2 rivnut replacement procedure. See Figure 1
1.2. Disconnect and remove both lights from the removed curb side light panel. Retain the hardware.
1.3. Install the stop lamp at the bottom position and the other lamp at the top position on the removed curb side stop and flasher light panel. See Figure 2.
1.4. Disconnect and remove both lights from the removed street side light panel. Retain the hardware.
1.5. Install the stop lamp at the bottom position and the other lamp at the top position on the removed street side stop and flasher light panel. See Figure 2 .
CAUTION
Position the TOP mark at the top of both lamps when fixing the lamps to the light panel. See Figure 2.
1.6. Reconnect the lamp and reinstall the curb and street side light panel with the retained hardware. Secure the harness with G5007996 tye rap.
LEVEL 2 : RIVNUT REPLACEMENT PROCEDURE
2.1. Remove the defective rivnut.
2.2. Repair the fiber where the removed defective rivnut was located, following the procedure detailed in Section 01 : Body of your Nova Bus maintenance manual.
2.3. Drill the repair fiber and install a new N44701 Rivnut.
2.4. Proceed with step 1.2 of Level 1 procedure.
Nova Bus, a division Prevost Car (US) Inc.
IMPORTANT SAFETY RECALL
THIS NOTICE APPLIES TO YOUR VEHICLE – SEE VIN IN ANNEX A
Saint-Eustache, May 6th 2021
M Joe Customer
Bus transit co
260, Banker Road
Plattsburgh, NY, 12901
This Defect Notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.
Nova Bus has decided that certain Nova Bus LFS and LFSArticModel Year2008 to 2020fail to conform to Federal Motor Vehicle Safety Standard No. 108.
Nova Bus have voluntary filed the vehicle recall 21V-151 and will issue a recall campaign service documents CR5065 to address this situation.
Onthe affected vehicles the stop lamps and tail lamps center line height are at 75 inches from the ground. The FMVSS 108 table I-a requires “Not less than 15 inches, nor more than 72 inches”. Under certain conditions, this may increase the risk of a crash due to reduced stop lamp and tail lamp visibility. Nova Bus has not received any report of injury or death associated with this defect. Therefore, we consider this as a proactive measure to protect the public from the potential safety risk associated with this defect.
Nova Bus will release a service document explaining the remedy program. This document will be available to you on our web site at https://www.novabus.com/on-line-services.html. The necessary replacement parts are available via the Prevost Parts distribution network. Nova Bus will assume the parts and labour costs according to the warranty claim policies in effect. The vehicle can be remedied starting from May 25th 2021 according to parts availability. The repairs should take approximately 30 minutes to 45 minutes to complete.
Any lessor who receives a notification of a determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send a copy of such notice to the lessee. This requirement applies to both initial and follow-up notifications.
After contacting your customer support manager, if you are still not able to have the safety defect remedied without charge and within reasonable time, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE, Washington, DC 20590; or call the toll-free Vehicle Safety Hotline 1-888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov.
You may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of a problem associated with this defect. Submit copies of all documentation supporting your claim according to the rules specified in the “General Plan for Reimbursement of Pre-notification Remedies” provided in this mailing under the heading “Annex B”.
If you have any questions regarding the requirements of this campaign, please contact your customer support manager.
Sincerely,
Kevin Dawson
Vice-President General Manager Services
SEOCONTENT-STARTNQF705003 VERSION 3
REFERENCE: Nova Bus Manuals
SECTION: 16: 24-Volt Electrical system
RS NO: MQR 7621-2249
EFFECTIVE IN PROD.: LD83 (2021AL)
TC RECALL NO: 2021-128
NHTSA RECALL NO: 21V-151
MATERIAL
QTY PART NO REV. DESCRIPTION REPLACES PART N°
LEVEL 1
5 G5007996 – Cable ties –
LEVEL 2 (only if required*)
1 N71801 A Rivnut 1/4 –
1 N80509 A Bolt 1/4 –
1 N47838 A Washer –
Materials will be available within 47 days once your order has been placed. To order, please
contact Prevost Parts by phone at 1‑800‑771‑6682, by fax at 1‑888‑668‑2555 or by email at
prevostparts.commandes@volvo.com. Specify document number, quantity of parts required and shipping address.
* The material identified in Level 2 is to be ordered only for vehicles that meet the criteria defined in Level 1.
LEVEL DESCRIPTION
DIRECT CHARGES
TIME
LABOUR MATERIAL
1 Reposition stop lamps to the position below and tail lamps to the top
position. Nova Bus Nova Bus 30 min
2 Replace any damaged rivnut Nova Bus Nova Bus 15 min
SUBJECT: Rear stop lamps
JUSTIFICATION: Rear stop lamps are located too high above the ground. FMVSS 108 requires not less
than 15 inches, nor more than 72 inches from the ground.
REVISION HISTORY
REV. DATE CHANGE DESCRIPTION WRITTEN BY
NR 2021MA12 Initial release Luc Carignan
DISPOSAL OF PARTS
REMOVED PARTS ARE:
DISCARDED
* RETAINED * Dispose of the unused parts and the defective parts in
accordance with local environmental standards in effect.
Yes –
APPROVED BY:
APPLICATION DEADLINE: NA
CLAIM REFERENCE NUMBER: SR-5065
CR5065E
PAGE 1 OF 8
RECALL CAMPAIGN
NQF705003 VERSION 3
CLIENT ORDER
ROAD NUMBER VIN (2NVY/4RKY…)
QTY
FROM TO FROM TO
Brampton – Ontario L789 1401 1408 L82J4E3001216 L82J1E3001223 8
Brampton – Ontario L816 1409 1415 L82J3E3001224 L82J9E3001230 7
Brampton – Ontario L864 1501 1510 L82JXF3001500 L82J6F3001509 10
Brampton – Ontario L865 1511 1519 L82JXF3001514 L82J9F3001522 9
Brampton – Ontario L941 1614 1623 L82J1G3750123 L82J2G3750132 10
Brampton – Ontario L942 1601 1613 L82J6G3750070 L82J4G3750083 13
Brampton – Ontario LA20 1707 1713 L82J5H3750532 L82J6H3750538 7
Brampton – Ontario LA21 1701 1706 L82J8H3750539 L82J1H3750544 6
Brampton – Ontario LB01 1801 1817 L82J3H3750948 L82J6J3750982 17
Brampton – Ontario LB02 1818 1823 L82J3J3751121 L82J2J3751126 6
Brampton Ontario LC23 1901 1907 L82J3K3751878 L82J9K3751884 7
Brampton Ontario LC54 1908 1916 L82J0K3751885 L82JXK3751893 9
Brampton Ontario LC97 — — L82MXL3752778 L82MXL3752778 2
Brampton Ontario LD18 2007 2024 L82J5L3752614 L82J5L3752631 18
CHARM city Baltimore – Maryland LC73 1910218 1910223 L82J4K9777447 L82J8K9777452 6
CHARM city Baltimore – Maryland LD37 1910234 1910239 L82JXL9777745 L82J3L9777750 6
Cold Lake LA99 5013 5014 L82J7J3751302 L82J9J3751303 2
Cornwall – Ontario LB55 — — L82J8J3751468 L82J8J3751468 1
Cornwall Ontario – Metrolinx L935 — — L82J3F3001838 L82J5F3001839 2
Cornwall Ontario – Metrolinx LA53 — — L82J2H3750892 L82J6H3750894 3
Demo – Method Bus BAE LC87 — — L82L5L9777539 L82L5L9777539 1
Demo- Altoona HEV BAE (REF LA95) LB38 — — L82L7H3750940 L82L7H3750940 1
Demo CNG L716 — — L82A5D3000896 L82A5D3000896 1
Duke University – North Carolina L938 – – L82L8G9775399 L82L0G9775400 2
Duke University – North Carolina LB08 — — L82L9J3751562 L82L2J3751578 3
Duke University – North Carolina LA38 — — L82L9H9775994 L82L9H9775994 1
Duke University – North Carolina LA39 — — S92LXH9775995 S92LXH9775995 1
Fredericton – New Brunswick L774 8131 8131 L82U7D3000960 L82U7D3000960 1
Fredericton – New Brunswick L812 — — L82J4E3001202 L82J4E3001202 1
Fredericton – New Brunswick L836 8143 8143 L82J9E3001390 L82J9E3001390 1
Fredericton – New Brunswick L901 8151 8151 L82J7F3001602 L82J7F3001602 1
Fredericton – New Brunswick L968 8161 8162 L82J1G3750218 L82J3G3750219 2
Fredericton – New Brunswick LA15 8171 8174 L82J1H3750589 L82J1H3750592 4
Fredericton – New Brunswick LA33 8181 8184 L82J6H3750944 L82J1H3750947 4
Guelph – Ontario L767 237 239 L82UXD3000967 L82U3D3000969 3
Guelph – Ontario L835 240 243 L82J0E3001391 L82J6E3001394 4
Guelph – Ontario L927 244 247 L82J1F3001756 L82J9F3001763 4
Guelph – Ontario L985 248 251 L82J7G3750255 L82J2G3750258 4
Moncton (Codiac) – New Brunswick LA06 — — L82J3G9775552 L82JXG9775564 9
Moncton (Codiac) – New Brunswick LA42 — — L82J8H9776066 L82J0H9776076 11
Moncton (Codiac) – New Brunswick LA58 — — L82J2J9776389 L82J2J9776389 1
Moncton (Codiac) – New Brunswick LB84 N/A N/A L82J3K9777004 L82J3K9777004 1
CR5065E
PAGE 2 OF 8
RECALL CAMPAIGN
NQF705003 VERSION 3
CLIENT ORDER
ROAD NUMBER VIN (2NVY/4RKY…)
QTY
FROM TO FROM TO
Niagara Falls – Ontario L771 1396 1397 L82U9D3000958 L82U0D3000959 2
Niagara Falls – Ontario L987 1601 1604 L82J6G3750344 L82J1G3750347 4
Niagara Falls Ontario – 60′ metrolinx LB98 1935 1936 S92J9K3752106 S92J0K3752107 2
Niagara Falls Ontario – 60′ metrolinx LC61 1937 1938 S92J2K3752108 S92J4K3752109 2
Niagara Falls Ontario – Metrolinx LA97 1805 1808 L82J0J3750993 L82J6J3750996 4
Niagara Falls Ontario – Metrolinx LA98 1809 1810 S92J7J3751003 S92J9J3751004 2
Niagara Falls Ontario – Metrolinx LB13 1811 1811 L82J8J3750997 L82J8J3750997 1
Niagara Falls Ontario – metrolinx LC89 1930 1934 L82J2L9777528 L82J4L9777532 5
Niagara Falls Ontario – Metrolinx LD63 2112 2115 L82J5L9777765 L82J0L9777768 4
Niagara Falls Ontario – Metrolinx LD53 2116 2119 S92J7L9777761 S92J2L9777764 4
Ottawa – Carleton Regional Transit Co. – O.C. –
metrolinx LC67 4683 4736 L82J7K3752127 L82J4K3752182 54
Ottawa – Carleton Regional Transit Co. – O.C. –
metrolinx LD21 4776 4830 L82J5L3752662 L82J3L3752756 55
Ottawa – Carleton Regional Transit Co. – O.C. –
metrolinx LD51 4831 4849 L82J4L9777711 L82J1L9777729 19
Ottawa – OC transpo LB80 4601 4609 L82J0J3751576 L82J3J3751586 9
Ottawa – OC transpo LC16 4610 4682 L82J7K3751771 L82JXK3751912 73
Ottawa – OC transpo – metrolinx LC68 4737 4755 L82J0K9777428 L82J3K9777472 39
RMA World wide chauffeured Transportation LC98 N/A N/A L82J6L9777693 L82J7L9777704 12
San Juan Puerto Rico LC03 2019-01 2019-06 L82J9K9777251 L82J8K9777256 6
San Juan Puerto Rico LD01 2020-01 2020-01 L82J0L9777561 L82J0L9777561 1
San Juan Puerto Rico LD32 2021-01 2021-10 L82J5L9777751 L82J6L9777760 10
Sarnia Ontario L873 151 152 L82J0F3001599 L82J0F3001600 2
Sarnia Ontario L883 153 153 L82J4G3750021 L82J4G3750021 1
Sarnia Ontario L963 162 162 L82J7G3750305 L82J7G3750305 1
Sarnia Ontario LA36 171 172 L82J8H3750752 L82JXH3750753 2
Sault Ste. Marie Ontario L934 — — L82JXG3750038 L82JXG3750038 1
Sault Ste. Marie Ontario LC06 — — L82J3K3751900 L82J5K3751901 2
St. John – New Brunswick L871 40585 40586 L82J8F3001592 L82JXF3001593 2
St. John – New Brunswick L939 40687 40687 L82J0G3750078 L82J0G3750078 1
St. John – New Brunswick LB05 38888 38899 L82J8J3750983 L82J1J3750999 12
St. John’s – Newfoundland L808 1415 1419 L82J4E3001152 L82J1E3001156 5
St. John’s – Newfoundland L875 1520 1525 L82JXF3001478 L82J3F3001483 6
St. John’s – Newfoundland L930 1626 1630 L82J7F3001826 L82J9F3001830 5
Stratford – Ontario L893 — — L82J9F3001584 L82J0F3001585 2
Stratford – Ontario LB19 — — L82J3J3751183 L82J5J3751184 2
Strathcona County Transit Edmonton Alberta LD20 2031 2035 L82J3L3752742 L82J0L3752746 5
Thunder Bay – Ontario L806 — — L82J6E3001170 L82J8E3001171 2
Thunder Bay – Ontario L863 — — L82J8F3001558 L82J6F3001560 3
Thunder Bay Ontario – Metrolinx L944 — — L82J6G3750084 L82JXG3750086 3
Thunder Bay Ontario – Metrolinx LA01 — — L82J5H3750448 L82J7H3750449 2
Thunder Bay Ontario – Metrolinx LA57 — — L82J8H3750895 L82J8H3750928 12
CR5065E
PAGE 3 OF 8
RECALL CAMPAIGN
NQF705003 VERSION 3
CLIENT ORDER
ROAD NUMBER VIN (2NVY/4RKY…)
QTY
FROM TO FROM TO
University of Alabama – Alabama L787 7028 7029 L82J2E4500507 L82J4E4500508 2
University of Alabama – Alabama L902 7030 7030 L82J2F4500993 L82J4F4500994 2
University of Alabama – Alabama L961 7032 7033 L82J7G9775294 L82J9G9775295 2
University of Alabama – Alabama LA02 7034 7037 L82J8G9775546 L82JXG9775550 4
Vancouver Airport Authority – YVR British Columbia L856 705 706 L82LXH3750530 L82L1H3750531 2
Vancouver Airport Authority – YVR British Columbia L912 173 178 L82L5F3001812 L82L4F3001817 6
Windsor – Ontario LB24 8025 8026 L82JXJ3751424 L82J1J3751425 2
Windsor Ontario – Metrolinx L886 570 577 L82J8F3001818 L82J5F3001825 8
Windsor Ontario – Metrolinx LA56 578 601 L82J5J3751007 L82J0J3751030 24
Windsor Ontario – metrolinx LC21 8027 8045 L82J3L9777540 L82J0L9777558 19
CR5065E
PAGE 4 OF 8
RECALL CAMPAIGN
NQF705003 VERSION 3
PROCEDURE
LEVEL1 ; REPOSITION STOP LAMP AND TAIL LAMPS
1.1. Remove the 3 screws retaining the street and curb side panels on the side of the vehicle. If one of the screws
spins or it is hard to remove, you will need to perform the level 2 rivnut replacement procedure. See Figure 1
WARNING
FOLLOW YOUR INTERNAL SAFETY PROCEDURES.
Street side panel Curb side panel
Screws to remove Screws to remove
Figure 1 – Side Panel Screws to Remove
CR5065E
PAGE 5 OF 8
RECALL CAMPAIGN
NQF705003 VERSION 3
1.2. Remove the rear retaining screws and remove the curb side stop and flasher light corner panel. Retain the
hardware. See Figure 2.
1.3. Remove the rear retaining screws and remove the street side stop and flasher light corner panel. Retain the
hardware. See Figure 2.
Street side Curb side
Figure 2 – Rear Screws to Remove
Retaining screws to remove
CR5065E
PAGE 6 OF 8
RECALL CAMPAIGN
NQF705003 VERSION 3
1.4. Disconnect and remove both lights from the removed curb side corner panel. Retain the hardware.
1.5. Install the stop lamp at the bottom position and the other lamp at the top position on the removed curb side
stop and flasher light panel. See Figure 3.
1.6. Disconnect and remove both lights from the removed street side panel. Retain the hardware.
1.7. Install the stop lamp at the bottom position and the other lamp at the top position on the removed street side
stop and flasher light panel. See Figure 3.
CAUTION
Position the TOP mark at the top of both lamps when fixing the lamps to the corner plates. See Figure 3.
Street side
Light position before Light position after
Curb side
Light position after Light position before
Figure 3 – Stop Lamp New Position
CR5065E
PAGE 7 OF 8
RECALL CAMPAIGN
NQF705003 VERSION 3
1.8. Reconnect the lamp and reinstall the curb and street side corner panel with the retained hardware. Secure
the harness with G5007996 tye rap.
LEVEL 2 : RIVNUT REPLACEMENT PROCEDURE
2.1. Remove the side panel located between the rear light corner panel and the rear side window. Retain the
hardware. See Figure 4.
Remove either panel only
if one of the screws to
removed in step 1.1 spin or
its hard to remove
Figure 4 – Panel to Remove if a Screw Spin or its Hard to Remove
2.2. Remove the defective rivnut.
2.3. Install a new N71801 Rivnut.
2.4. Reinstall the removed side panel with the retained hardware. Proceed with step 1.2 of Level 1 procedure.
CR5065E
PAGE 8 OF 8
RECALL CAMPAIGN
********************************************************************************
NQF705003 VERSION 3
REFERENCE: Nova Bus Manuals
SECTION: 16: 24-Volt Electrical system
RS NO: MQR 7621-2249
EFFECTIVE IN PROD.: LD83 (2021AL)
TC RECALL NO: 2021-128
NHTSA RECALL NO: 21V-151
MATERIAL
QTY PART NO REV. DESCRIPTION REPLACES PART N°
LEVEL 1
5 G5007996 – Cable ties –
LEVEL 2 (only if required*)
1 N44701 A Rivnut 1/4 –
1 N25881 A Bolt 1/4 –
1 N17565 A Washer –
Materials will be available within 32 days once your order has been placed. To order, please
contact Prevost Parts by phone at 1‑800‑771‑6682, by fax at 1‑888‑668‑2555 or by email at
prevostparts.commandes@volvo.com. Specify document number, quantity of parts required and shipping address.
* The material identified in Level 2 is to be ordered only for vehicles that meet the criteria defined in Level 1.
LEVEL DESCRIPTION
DIRECT CHARGES
TIME
LABOUR MATERIAL
1 Reposition stop lamps to the position below and tail lamps to the top
position. Nova Bus Nova Bus 30 min
2 Replace any damaged rivnut Nova Bus Nova Bus 15 min
SUBJECT: Rear stop lamps
JUSTIFICATION: Rear stop lamps are located too high above the ground. FMVSS 108 requires not less
than 15 inches, nor more than 72 inches from the ground.
REVISION HISTORY
REV. DATE CHANGE DESCRIPTION WRITTEN BY
NR 2021MA14 Initial release Luc Carignan
DISPOSAL OF PARTS
REMOVED PARTS ARE:
DISCARDED
* RETAINED * Dispose of the unused parts and the defective parts in
accordance with local environmental standards in effect.
Yes –
APPROVED BY:
APPLICATION DEADLINE: NA
CLAIM REFERENCE NUMBER:
CR5077E
PAGE 1 OF 6
NOVaBUS RECALL CAMPAIGN
–
NOVaBUS RECALL CAMPAIGN CR5077E
ROAO NUMBER VIN (2NVY/4RKY … )
CLIENT ORDER QTY
FROM TO FROM TO
Belleville Transit – Ontario 3
Belleville Transit – Ontario 2
Belleville Transit – Ontario
Belleville Transit – Ontario (ref L82U2D
Brampton – Ontario 0917 0926 L82U89 10
Clemson Area Transit – South Carolina (ref 5
Demo – Articulated Bus 1
Duke University – North Carolina 2
Duke University – North Carolina (ref. 8
Fredericton – New Brunswick 8111 8112 2
Fredericton – New Brunswick 8113 8113 1
Guelph – Ontario 221 224 4
Guelph – Ontario 225 228 4
Guelph – Ontario 234 235 2
Hampton Roads – Virginia 7
Krapfs Coaches – Pennsylvania (ref
Niagara Falls – Ontario 2986 2989 L82U09 4
Niagara Falls – Ontario S92U3C 11
Niagara Falls – Ontario 5
Niagara Parks Commission – Ontario 2
Niagara Parks Commission – Ontario 9
Peterborough – Ontario 4
Puerto Rico (ref. 16
Sault Ste-Marie Transit Services – Ontario (ref. 135 139 5
Sault Ste-Marie Transit Services – Ontario (ref
St. John’s – Newfoundland 1066 1066 1
St. John’s – Newfoundland 1201 1209 9
St. John’s – Newfoundland 1310 1314 5
Stratford – Ontario
Stratford – Ontario
Stratford – Ontario L82U9D
Strathcona County Transit – Alberta 2010 2010 L82U69 1
Strathcona County Transit – Alberta 3005 3010 L82X59 6
Strathcona County Transit – Alberta 2011 2023 13
Strathcona County Transit – Alberta 2024 2028 5
Thunder Bay – Ontario L82U19 3
Thunder Bay – Ontario L82UXB 3
Thunder Bay – Ontario 20168 20168 3
Thunder Bay – Ontario 3
Timmins – Ontario 2
Timmins – Ontario 2
PAGE 2 OF 6
NQF705003 VERSION 3
NQF705003 VERSION 3
CLIENT ORDER
ROAD NUMBER VIN (2NVY/4RKY…)
QTY
FROM TO FROM TO
University of Alabama – Alabama — — L82U9A4 L82U0A4 2
University of Alabama – Alabama — — L82U9B4 L82UOB4 2
University of Alabama – Alabama 7024 7025 L82U5C4 L82U1C4 2
University of Alabama – Alabama 7026 7027 L82U4D4 L82U6D4 2
University of Colorado – Colorado — — S92U693 S92U693 1
University of Colorado – Colorado — — S92U893 S92U893 1
University of Colorado – Colorado — — S92UXB4 S92U6B4 2
CR5077E
PAGE 3 OF 6
NOVaBUS RECALL CAMPAIGN
NOVaBUS RECALL CAMPAIGN CR5077E
I E!3 WARNING
FOLLOW YOUR INTERNAL SAFETY PROCEDURES.
PROCEDURE
LEVEL 1 ; REPOSITION STOP LAMP AND TAIL LAMPS
1.1. Remove the 3 anchor screws retaining the street and curb side light panels. If one of the screws spins or it
is hard to remove, you will need to perform the level 2 rivnut replacement procedure. See Figure 1
Street side panel
NQF705003 VERSION 3
Remove the 3 anchor
screw on each light panel
Figure 1 – Light Panel Screws to Remove
Curb side panel
PAGE 40F 6
NOVaBUS RECALL CAMPAIGN CR5077E
1.2. Disconnect and remove both lights from the removed curb side light panel. Retain the hardware.
1.3. Install the stop lamp at the bottom position and the other lamp at the top position on the removed curb side
stop and flasher light panel. See Figure 2.
1.4. Disconnect and remove both lights from the removed street side light panel. Retain the hardware.
1.5. Install the stop lamp at the bottom position and the other lamp at the top position on the removed street side
stop and flasher light panel. See Figure 2 .
.(DcAUTION
Position the TOP mark at the top of both lamps when fixing the lamps to the light panel. See Figure 2.
Street side Curb side
Light position before Light position after Light position after 11 Light position before
Figure 2 – Stop Lamp New Position
PAGE 5 OF 6
NQF705003 VERSION 3
NQF705003 VERSION 3
1.6. Reconnect the lamp and reinstall the curb and street side light panel with the retained hardware. Secure the
harness with G5007996 tye rap.
LEVEL 2 : RIVNUT REPLACEMENT PROCEDURE
2.1. Remove the defective rivnut.
2.2. Repair the fiber where the removed defective rivnut was located, following the procedure detailed in
Section 01 : Body of your Nova Bus maintenance manual.
2.3. Drill the repair fiber and install a new N44701 Rivnut.
2.4. Proceed with step 1.2 of Level 1 procedure.
CR5077E
PAGE 6 OF 6
NOVaBUS RECALL CAMPAIGN
*******************************************************************************
ANNEX A –
Make/Marque – Model/Modèle – Model Year/Année modèle – Road# – VIN/NIV
ANNEX B –
General Plan for Reimbursement of Pre-Notification Remedies
When a Nova Bus vehicle is affected by a safety recall campaign and the owner (claimant) has the
problem corrected at their own expense prior to receiving notification of the recall, Nova Bus will
reimburse the claimant for the reasonable amount paid for repairs (i.e. the cost of parts, labor, disposal
fees and taxes) that addressed the defect as stated in the safety recall notification. To qualify, repairs
must have been completed no earlier than one year prior to the release of the recall
(notification to the government) and no later than 10 days after the last mailing of the initial
customer notification letter pertaining to the recall. The following information is required for your
claim to be processed. Please print legibly.
Date: ________________ Recall #: ____________ 17 digit VIN:
________________________
260 Banker Rd, Plattsburgh, NY, USA 12901 | Tel.: 1 800 350-6682 | Fax: 450 974-3001 | novabus.com
Owner’s Name: ____________________________ Own/Lease (circle one)
Address: __________________________________ Date of Repair:
______________________
City, State, Zip: _____________________________ Amount Requested:
___________________
Phone #: __________________________________ Email:
____________________________
All claims MUST be accompanied by accurate and complete documentation (the invoice/receipt
must provide the VIN, date of repairs, total amount paid and include a breakdown of the parts, labor, and
other costs. Costs associated with the recall repair must be highlighted or circled on the invoice).
I CERTIFY THAT I PAID FOR REPAIRS THAT CORRECTED THE SAFETY DEFECT AS STATED IN THE
RECALL LETTER PRIOR TO BEING NOTIFIED. I ALSO CERTIFY THAT I HAVE PROVIDED CLEAR
DOCUMENTATION OF THESE REPAIRS AND THAT ALL INFORMATION PROVIDED IS COMPLETE AND
ACCURATE TO THE BEST OF MY KNOWLEDGE.
Claimant Witnessed by (required)
_________________________ ________________________________________________
Authorized Signature and Date Notary Signature and Date Affix Notary Stamp
Contact Information
Submit copies of all documentation supporting your claim to:
Nova Bus Warranty, TMAC
850, chemin Olivier
Saint-Nicolas (QC) G7A 2N1
Canada
Email: adm.novabus.warranty@volvo.com
Allow 60 days for processing. Nova Bus is not responsible for claims submitted to the wrong
address.
Nova Bus will consider all claims, but may deny a claim, in whole or in part, for any of the following
reasons:
Fraudulent claim or vehicle not part of recall
Incomplete application or support documentation
The repair did not address the safety defect or non-compliance that led to the recall, or the repair was
not of the same type (repair, replacement) as the recall remedy.
This process is NOT intended to handle accident or property damage claims. Claims of that
nature MUST be directed to our legal department at 35, Gagnon Blvd, Sainte-Claire (QC),
Canada, G0R 2V0.
SEOCONTENT-END
14 Affected Products
Vehicle
MAKE | MODEL | YEAR |
NOVA BUS | LFS | 2008-2021 |
11 Associated Documents
Owner Notification Letter(Part 577)
RCONL-21V151-8354.pdf 136.983KB
Owner Notification Letter(Part 577)
RCONL-21V151-2363.pdf 136.986KB
Remedy Instructions and TSB
RCRIT-21V151-2487.pdf 535.08KB
Remedy Instructions and TSB
RCRIT-21V151-3922.pdf 1078.169KB
Remedy Instructions and TSB
RCRIT-21V151-9790.pdf 2617.608KB
Noncompliance Notice 573 Report
RCLRPT-21V151-7113.PDF 213.577KB
Recall Acknowledgement
RCAK-21V151-7011.pdf 645.103KB
Recall Quarterly Report #1, 2021-2
RCLQRT-21V151-9158.PDF 211.121KB
Recall Quarterly Report #2, 2021-3
RCLQRT-21V151-0394.PDF 211.229KB
Recall 573 Report- Amendment 2
RCLRPT-21V151-6191.PDF 213.572KB
Recall Quarterly Report #3, 2021-4
RCLQRT-21V151-2777.PDF 211.312KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=21V151&docType=RCL
“This site contains affiliate links for which OEMDTC may be compensated” |
- 💡 SUPERIOR MATERIAL: The housing of the LED light bulbs is made of superior aviation aluminum material, which is sturdy and durable. Reliable thermal conductivity and heat dissipation keep your bulbs working stably at a constant temperature, with a service life of up to 50,000 hours for long term use.
- 💡 SUPER HIGH BRIGHTNESS: This high beam LED bulbs have super high brightness with low energy consumption, energy saving and high efficiency. It can provide you with a clearer and brighter driving vision at night and improve daily driving safety. It can be used normally even in all kinds of bad weather conditions.
- 💡 HIGHLY EFFICIENT DESIGN: Our car light bulbs total length (+ wire length) is 5.51 inch, height is 3.15 inch, and bottom diameter is 1.38 inch. Built-in high speed silent fan provides you with more efficient cooling performance. Ultra-thin light bottom to avoid lack of light assembly space.
- 💡 EASY TO INSTALL: The H11 LED bulbs are designed with wire integration. Plug and play, no extra tools are needed, easy to install. No polarity setting, can effectively solve the problems such as bulb flickering, not easy to make mistakes. More stable operation, you can use it with confidence.
- 💡 WIDE APPLICATION: We have prepared 2pcs H11/H8/H9 LED light bulbs for you. It is suitable for most of the car models on the market with DC voltage of 12V, such as car, truck, SUV, RV, van and so on. Can be used to replace LED high beam and low beam, etc. Wide range of application.
- 【IMPORTANT】Replacement for stock D4S HID headlights only, DOES NOT FIT if your car has stock Halogen/LED headlight.
- 100% Quartz Anti-UV Glass, Excellent in Performance. Up to 3500 Lumens - More Brighter than Original Standard HID Bulb.
- High Quality Xenon Gas and APL pills, Tungsten Metal Electrode.
- Increase 50m Irradiation Distance, Gain 4.5 Seconds more Brake Reaction Time.
- Pack of 2 Xenon HID Headlight Bulbs - D4S 8000K 35W - OEM Replacement - Original Quality. Hg-free - More Environmentally Friendly - 24 Months Warranty.
- 【No Flicker No Delay】Our 9005/9006 LED headlight bulbs light up with no delay and respond quickly, and the wide low voltage range of 12-24V protects the LED bulbs from voltage fluctuations. It works for a long time without flickering, has good stability and can be used even in bad weather.
- 【50,000 Hours Service Life】Our LED car fog light bulbs are made of high-quality waterproof metal material aluminum and 20 beads, which are durable and not easy to break. Excellent heat dissipation, reduced power consumption, and a service life of up to 50,000 hours.
- 【Super Bright Beam】These 12V 100W low beam lights have a color temperature of 6500K and a luminous flux of 1000LM. They illuminate the car in all directions without dazzling oncoming vehicles and are more friendly to the driver's eyes. Compared with traditional halogen bulbs, they provide greater visibility and greater light transmission.
- 【Easy to Install】These 6500K front light are easy to install, plug and play, no need to change the car's internal wiring, wireless integrated design, just plug into the corresponding groove in the fog light cover, saving you money and time in repairs.
- 【Widely Used】Our daytime running lights are suitable for most types of cars, such as cars, SUVs, trucks, etc. They can be used as daytime running lights, fog lights, low beams, and will not cause any harm to oncoming drivers, glare, practical and safe.
- 【600% Brighter Than Halogens】The h11 LED bulb adopts the newest 24pcs LED chips. Each set provides 22,000lm of 6500K white light output. Even in bad weather, the AUTOONE h8 led bulbs will make road signs and obstacles clearly visible. Make you can react in time
- 【Safe & Ideal Beam Pattern】The h11/h9 leds pattern is close to stock lamp with 0.03in ultra-thin chip spacing which achieve real 360 degree lighting with no dark spots or scattered light. Instant Illumination and strong penetration, No glare, stay polite. Win-win design for safety and brightness
- 【Direct Fit. Hassle-free Installation】AUTOONE h11 led bulbs features a plug-and-play wireless and 1:1 size halogens’ design that allows people to get rid of bulky drivers and annoying wiring harnesses. No modifications on the enclosure or housing, 5 minutes easy installation
- 【Up to 7 Years Lifespan】Built-in 12,000RPM high-speed silent cooling fan. Combined with high-quality LED chips along with copper base and unique hollow design on all-in-one aluminum body. Effectively improve the heat dissipation efficiency of AUTOONE h11/h9/h8 LED bulbs by 500%. Ensure h11 light bulb a longer service life up to 60,000 hours
- 【99% of Models Compatible】Built-in upgraded intelligent driver, have professional and rigorous testing make AUTOONE h11 LED light compatible with 99% of models without problem. NOTE: For few models, computer system may be sensitive and will display an error message or flicker for any aftermarket bulbs. To solve the issue, an additional decoder is needed, message to us on Amazon so we can send decoder directly
- 57 picecse car LED Package Include: 4 pieces 28mm, 4 pieces 29mm (1.14 inch) , 4 pieces 31mm (1.22 inch) , 6 pieces 31mm (1.412 inch) , 8 pieces 41mm (1.61 inch) festton light, 8 pieces 41mm Loop (1.73 inch) light and 4pieces T5, 16 pieces T10 wedge light, 4 picecs BA9S
- Main application: Dome Map Trunk Door Glove Box Vanity License plate light, Please enter your car model to check the bulb application location. The package does not include bulbs in all locations, please purchase on demand.
- Tips: This LED package is suitable for almost 99% of the interior lights of the car, if the car compatibility table does not list your model, does not mean that it is not suitable for use, check the original car bulb number as listed below will apply
- Main Parameters: about 6000k pure white, about 120 lumen, about 2 times brightness of original bulb, work volt 9~14V.
- Installation method: Plug and Play, Black model are Error Free, No Other Parts or Modifications Required
- Product Includes: 42PCS LED interior car lights in 6 different sizes, including T10, 31mm, 36mm, 41mm, and other sizes, to meet various needs for car interior lighting.
- Versatile Applications: These LED interior lights can be used in multiple positions in your car, including dome lights, map lights, license plate lights, glove box lights, and trunk lights, providing a modern and stylish lighting upgrade for your vehicle.
- Easy Installation: Designed for plug-and-play installation, with the correct polarity of the electrode, it is easy to replace the old bulb.
- Energy-efficient: These car LED lights interior are made with durable materials and feature energy-saving LED chips, ensuring stable and efficient lighting performance for enhanced visibility in your vehicle.
- Wide Compatibility: Compatible with various socket types, such as T10, DE3175, 194, 168, and more, these LED bulbs are suitable for most cars, trucks, SUVs, and other vehicles. Please ensure to carefully check the size of your socket before ordering.
- Adequate packaging:Rafeal Auto offers a package of 10 3157 premium bulbs for your replacement needs, which you can also share or keep as a spare.
- Ultra-long life:Our 3157brake light bulbs are made of high quality materials, and the high precision manufacturing process makes our car light bulbs have a super long service life, allowing you to use them for a long time!
- Multi-functional applications:Rafeal Auto's high quality 3157 bulbs have a wide range of applications and can be used as signal bulbs, tail bulbs, side marker bulbs, brake bulbs and more!
- Fine Appearance:The well-designed 3157 bulb has an attractive appearance and durable characteristics, allowing you to forget about maintenance and drive your car better!
- Gentle Reminder:Please confirm your car model before purchase, 3157 car light bulb is suitable for specific car models, confirm your car is suitable or not!
- 🚖 High Quality: The halogen bulb is made from high quality quartz glass material, the thickness of glass is increased and the internal pressure is increased in order to obtain more than 500 hours life, long lasting durability.
- 🚖 Super Bright: H7 car light bulb emits super white light with exceptional clarity on the road to improve driver safety. Manufactured by trusted OEM light source supplier. Meet DOT regulations.
- 🚖 Features: The halogen bulb has 100W power and up to 1800LM brightness, wider and more clarity light output than standard halogen bulb, and you can still see the road clearly in greasy weather and rainy weather.
- 🚖 Easy Installation: Plug and play, no tool needed, just remove your stock bulbs and replace with new bulbs. Please wear gloves when you install! Avoid touching the bulb with bare hands!
- 🚖 Application: Compatible with H7 socket (PX26D), 1 pair packaged. Replaces H7 high beam, H7 low beam, H7 driving light, H7 fog light. If you have any questions, please feel free to contact us.
- Adequate packaging:Rafeal Auto offers a package of 10 194 premium bulbs for your replacement needs, which you can also share or keep as a spare.
- Ultra-long life:Our 194 car bulbs are made of high quality materials, and the high precision manufacturing process makes our car light bulbs have a super long service life, allowing you to use them for a long time!
- Multi-functional applications:Rafeal Auto's high quality 194 bulbs have a wide range of applications and can be used as signal bulbs, tail bulbs, side marker bulbs, brake bulbs and more!
- Fine Appearance:The well-designed 194 bulb has an attractive appearance and durable characteristics, allowing you to forget about maintenance and drive your car better!
- gentle reminder:Please confirm your car model before purchase, 194 car light bulb is suitable for specific car models, confirm your car is suitable or not!
Last update on 2024-04-14 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.