| “This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10171333
Manufacturer Communication Number: 059-726-00
Summary
Brake Assembly Kit for 7″, 10″ and 12″ Electric or Hydraulic Brakes Installation Instructions
1 Affected Product
Equipment
| BRAND | PART NO. | PRODUCTION DATES |
| DEXTER AXLE CO | DEXTER AXLE CO | |
INSTALLATION INSTRUCTIONS
Brake Assembly Kit for 7”, 10” and 12” Electric or Hydraulic Brakes
Notice to Buyer
It is recommended that all brakes be replaced at the same time to ensure balanced braking performance.
Remove the old brakes
- Jack up trailer and secure on adequate capacity jack stands. Follow trailer manufacturers recommendations for lifting and supporting the unit.
| CAUTION |
| Do not lift or support the trailer on any part of the axle or suspension system. Never go under any trailer unless it is properly supported on jack stands which have been rated for the load. Improperly supported vehicles can fall unexpectedly and cause serious injury or death. |
- Remove the wheel and drum from the spindle, leaving the brake exposed. Check armature surface and drum braking surface. Resurface if required per your Operation Maintenance Service Manual.
- Disconnect the brake actuation system.
- Electric brakes
Cut the magnet wire and remove the strain relief from the dust shield.
Hydraulic brakes
Remove the hydraulic line from the wheel cylinder.
- Remove the brake mounting hardware. Then remove the old complete brake assembly and save the brake mounting hardware for installing the new brake.
Installing the new brakes
- Install the new brake assembly using the old hardware. If new hardware is required (or desired), select the correct components according to your brake size from the following chart.
| Brake Size | Qty | Part No. | Description |
| 7″ | 4 | 006-017-00 | 7/16-20 Hex Nut Torque 45-70 Ft. Lbs. |
| 10″ | 4 | 006-017-00 (2-3/8” Tube) | 7/16-20 Hex Nut Torque 45-70 Ft. Lbs. |
| 10″ | 4 | 006-207-00 (3” Tube) | 7/16-20 Hex Nut Torque 45-70 Ft. Lbs. |
| 12″ | 5 | 006-193-00 | 3/8-24 Hex Nut Torque 25-50 Ft. Lbs. |
- Reconnect the brake actuation system. Refer to Dexter’s current Operation Maintenance Service Manual for proper connection.
- Remount the drum and wheel. Refer to Dexter’s current Operation Maintenance Service Manual for proper bearing adjustment procedure.
- After replacement of brakes, the brakes must be re-burnished to seat the new components. This should be done by applying the brakes 20-30 times from an initial speed of 40 mph, slowing the vehicle to 20 mph. Allow ample time for the brakes to cool between applications. This procedure allows the new brake shoes to seat in to the drum surface.
Note: The current Dexter Axle Operation Maintenance Service Manual is available at www.dexteraxle.com.
059-726-00 | 2020.01
059-726-00
https://www.nhtsa.gov/recalls?nhtsaId=10171333
https://static.nhtsa.gov/odi/tsbs/2020/MC-10171333-0001.pdf
Loading...
Reload document 
Open in new tab
Bestseller No. 1
Bestseller No. 2
VEVOR Electric Trailer Brake Assembly, 12" x 2", 2 Pairs Self-Adjusting Electric Brakes Kit for 7000 lbs Axle, 5-Hole Mounting, Backing Plates for Braking System Part Replacement (2 Right + 2 Left)
- Self-Adjusting Electric Brake: Say goodbye to manual adjustments! Dive into the world of 12" x 2" electric trailer brake assemblies that self-adjust. It's not just smart; it's efficient and gives your trailer that smooth braking touch.
- Hassle-Free Installation: DIY's best friend! Our electric trailer brake is straightforward and a breeze to install. It's ready to install right out of the box and boasts high compatibility. Wherever you are, installation is just a few steps away.
- Built for the Long Haul: Keep on rolling! With a lifespan of up to 30,000 kilometers, these trailer brakes are in it for the long haul, designed for your trailer's daily adventures. Constructed from premium materials, our brakes promise robust durability and resistance to wear and tear.
- Versatility at Its Best: The trailer brake kit has a broad range of applications, including towing trailers, transporting goods, camping trips, and more. It's compatible with Dexter, AL-KO (a brand under the former), and other trailer axles.
- Top-Notch Packaging: When it comes to packaging, we don't just box; we care. Our trailer electric brake kit is packaged above industry standards. Every brake is meticulously checked and wrapped to ensure what you get is nothing short of perfect.
Bestseller No. 3
LIBRA 2 Sets Trailer 5 on 4.5" B.C. Hub Drum Kits with 10" x2-1/4 Electric Brakes for Tandem 3500 Lbs Axles
- 4 x trailer 5 on 4.5" hub drum kits + 4 x 10"x2-1/4" electric brakes for Dexter and other brands 3,500 lbs trailer axle
- Drum Bolt pattern: 5 on 4.5", bearing races and 1/2"-20 studs installed, Ref part #. 008-247-05, 84546
- Kits also includ: 4x L68149 inner cone bearings and 4x L44649 outer cone bearings, 4x Grease seals 1.719" x 2.565", 4x E Z lube grease caps with rubber plug; 20 cone wheel nuts 1/2"-20 thread
- Also include: 2 left + 2 right 10"x2-1/4" electric brakes with 3" center bore and 4" mounting bolts circle diamter
Bestseller No. 4
Southwest Wheel 10" X 2-1/4" TruRyde Trailer Electric Brake Assembly (1 Right + 1 Left)
- Pair of 10" x 2.25" TruRdye electric trailer brake assemblies with parts.
- 4 Hole mounting, comes with mounting bolts, nuts, and lock washers
- For Alko, Dexter, Quality, or other popular trailer axle manufacturers.
- TruRyde Brakes
- TruRyde parts are manufactured to automotive standard in ISO/TS-16949 registered factory.
Bestseller No. 5
LIBRA 6 on 5.5" B.C. Trailer Hub Drum Kits with 12"x2" Electric Brakes for 5200-6000 Lbs Axle
- 2x Trailer 6 on 5.5" B.C. hub drum Kits + 2x 12"x2" electric brakes for 5200-6000 Lbs Axle. Bolt pattern: 6 on 5.5";
- Kit also include: 2x 25580 inner cone bearings and 2x 15123 outer cone bearings, 2x Grease seals 2.25" x 3.371", 2x EZ lube grease caps with rubber plug, 12 cone wheel nuts 1/2"x20 thread,
- Also include: One right and one left 12" x 2" electric brakes with 3-1/4" center hole
- Ref drum part #. 008-201, 42656; ref brake part #. K23-180-00, K23-181-00
Bestseller No. 6
Southwest Wheel 2-Pack 3,500 lbs. Trailer Axle Self Adjusting Electric Brake Kit 5-4.5" Bolt Circle
- 2-Pack 3,500 lbs. Trailer Axle Self Adjusting Electric Brake Kit 5-4.5" Bolt Circle
- 4 x 10" x 2 1/4" 5-4.5" bolt circle TruRyde hub and drums with parts (2 5/8" from center of one stud to the center of the next stud)
- 2 x 10" x 2 1/4" TruRyde Self-Adjusting electric backing plates
- Works with Al-Ko, Dexter, Lippert, and Quality Trailer Axles. TruRyde parts are manufactured to automotive standard in ISO/TS-16949 registered factory.
- Comes with TruRyde bearings, seals, lug nuts, open and closed grease caps, cotter pins, spindle washers, tang washers, spindle nuts, and brake mounting washers and nuts
Bestseller No. 8
4Pcs 10" x 2-1/4" Electric Trailer Brake Assemblies for 3,500lbs, Left and Right
- Compatible with: Fit For Alko/ for Dexter/ for Quality, and other brands 3,500lbs trailer axle
- Kit Includes: 2x 10" x 2-1/4" left electric brake assemblies, 2x 10" x 2-1/4" right electric brake assemblies, 16x spring pad, 16x nut
- Production and Installation: Strictly follow automotive standards and comply with the G3000 standard in the US; Easy to install
- Product Introduction: The AEagle electronic brake features non-asbestos brake linings for superior friction performance, ensuring longevity and enhanced braking capabilities.
- Quality Assurance: 12-month warranty! Tested before shipping.
Bestseller No. 9
JADODE Electric Trailer Brake Assembly 12" x 2" fits 7000 lbs Axle Trailers,Electric and Hydraulic Brake for One Pair- 23-108-00/23-181-00 Trailer Brakes
- Set of two 12" x 2" electric trailer brake assembly, for most 5200lbs 6000lbs 7000lbs trailer axle；Center hole diameter: 3-1/4"
- Fits the wheel bolt pattern 6 lug or 8 lug,fits spline size #42 steel brake drum.Bolt hole spacing: 2.0" O.C. around the top,Bolt hole spacing: 3.0" O.C.across the bottom
- Replace ：K23-180-00，K23-181-00；77-12EA-1-2；replace Axletech B12E-22 (12x2)；Al-Ko Lippert,etc
- The trailer brakes are NOT self adjusting, unlike most drum brakes on cars and trucks,need to be done when installed and periodically thereafter.If you cannot adjust yourself, please find a professional adjustment
- JADODE electric and hydraulic trailer brake parts offers 3 years warranty.Note make sure it matches you size,hub has to fit over
Bestseller No. 10
JADODE Trailer Electric Brake Assembly 10" x 2-1/4" for 3500 lbs Heavy Duty Axle Trailr 10" x 2.25" One Pair
- 10" x 2.25"electric trailer brake assembly (left & right side), fit most 3500lbs - 4000lbs trailer axle; 4-hole mount w/mounting bolt
- Fits the wheel bolt pattern 4 lug,fits spline size #84 steel drum; center hole diameter: 3" ; bolt circle diameter: 4"
- Replace 023-026-00 and 023-027-00；77-10-2；23-105, 23-106，296649；replace Dexter Lippert Al-Ko,etc brake assemblies
- The electric brakes are NOT self adjusting, unlike most drum brakes on cars and trucks,need to be done when installed and periodically thereafter.If you cannot adjust yourself, please find a professional adjustment
- JADODE electric and hydraulic trailer brake parts offers 3 years warranty.Note make sure it matches you size,hub has to fit over
Last update on 2024-04-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.