Incorrect GAWR on Certification Label – 2021-2022 Heartland North Trail Trailers

“This site contains affiliate links for which OEMDTC may be compensated”

March 29, 2022 NHTSA CAMPAIGN NUMBER: 22V199000

Incorrect GAWR on Certification Label/Part 567

An overloaded vehicle can increase the risk of a crash.

 

NHTSA Campaign Number: 22V199

Manufacturer Heartland Recreational Vehicles, LLC

Components EQUIPMENT

Potential Number of Units Affected 26

 

Summary

Heartland Recreational Vehicles, LLC (Heartland) is recalling certain 2021-2022 North Trail trailers. The Gross Axle Weight Rating (GAWR) listed on the Federal Certification Label, is incorrect, which can allow the vehicle to be overloaded. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, “Certification.”

 

Remedy

Dealers will send replacement certification labels to owners, free of charge. Owner notification letters were mailed May 4, 2022. Owners may contact Heartland customer service at 1-877-262-8032.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.

 


22v199 & 2022-148
V.I.N. TAG REPLACEMENT INSTRUCTIONS
99.01.66

The V.I.N. tag is broken into four sections. You will need to replace all four sections.

 

IMPORTANT: DO NOT APPLY NEW LABELS OVER THE EXISTING LABELS.

1. Locate sections 1, 2 and 4 on the driver’s side of your unit, typically just above the baggage door. Remove sections 1, 2 and 4 from your sidewall using a plastic scraping tool being careful not to scratch your unit. You may use isopropanol alcohol to assist with adhesion removal if needed.

2. Locate sections 1, 2 and 4 in the new set you received in the mail, remove from backer and carefully place on side wall in the order you removed them.

3. Locate section 3 in the door jamb closest to the hinge of the entrance door. Remove section 3 from your door jamb using a plastic scraping tool, being careful not to scratch your unit. You may use isopropanol alcohol to assist with adhesion removal.

4. Remove section 3 from the backer and place on the inside of the door jamb.

 


Chronology :

3/16 – engineering caught the discrepancy during a routine audit.

3/17-3/22 finalized scope

3/24 sent to the safety committee

 


2 Affected Products

Vehicle

MAKE MODEL YEAR
HEARTLAND NORTH TRAIL 2021-2022

 


7 Associated Documents

Noncompliance Notice 573 Report

RCLRPT-22V199-6799.PDF 215.007KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.97 KB]

 


Recall Acknowledgement

RCAK-22V199-8103.pdf 645.644KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [630.51 KB]

 


Remedy Instructions and TSB

RCRIT-22V199-9491.pdf 1011.562KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [0.96 MB]

 


Recall Quarterly Report #1, 2022-2

RCLQRT-22V199-9520.PDF 211.14KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.19 KB]

 


Recall Quarterly Report #2, 2022-3

RCLQRT-22V199-8202.PDF 211.243KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.29 KB]

 


Recall Quarterly Report #3, 2022-4

RCLQRT-22V199-5981.PDF 211.329KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.38 KB]

 


Owner Notification Letter(Part 577)

RCONL-22V199-4790.pdf 163.231KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [159.41 KB]

 


Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V199&docType=RCL

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
Bestseller No. 1
The Trailer Parts Outlet - 3.5k TK Trailer Axle - 3500 lb Idler 5 Lug - Dexter Compatible, 61/46 Hubface/Spring Center - (4'0) Frame Width / 5x4.5 Bolt Pattern
  • Specs: 3,500 lbs Idler Trailer Axle (Capacity 3.5K), 5 Lug, Tube: 2 3/8"
  • High Strength Straight Steel Axle Tube
  • Axle comes fully assembled, so all you'll have to do is attach the springs, the U-bolt kits, and the tire and wheel assemblies.
  • Underslung - Spring seats are welded to the bottom of the axle, which allows for a lower ride height.
  • Trailer Axle Design for use on Light Duty Trailers
Bestseller No. 2
The Trailer Parts Outlet - 2k TK Trailer Axle - 2000 lb Idler, 61/46 Hubface/Spring Center - (4'0) Frame Width / 4x4 Bolt Pattern
  • EZ Lube Design Removable rubber plug on the hub cap with easy access to a grease-able zerk fitting Grease your axle without pulling off your whole entire hub
  • Internal Wiring System To ensure seamless design Protect brake wires from wear and tear
  • High Strength Straight Steel Axle Tube Construction to ensure Even Tire Wear A better highway experience
  • Underslung - Axle is welded with spring seats on the bottom Allows for lower ride height For optimal usage, use with double eye springs
Bestseller No. 3
The Trailer Parts Outlet - 2k TK Trailer Axle - 2000 lb Idler, 71/58 Hubface/Spring Center - (5'0) Frame Width / 5x4.5 Bolt Pattern
  • Capacity: 2000 lbs, Tube:1-3/4 | 5x4.5 Bolt Pattern
  • EZ Lube Design: Removable rubber plug on the hub cap with easy access to a grease-able zerk fitting. Grease your axle without pulling off your whole entire hub.
  • Internal Wiring System: To ensure seamless design and protect brake wires from wear and tear.
  • High Strength Straight Steel Axle Tube Construction: To ensure even tire wear and a better highway experience.
  • Underslung - Axle is welded with spring seats on the bottom: Allows for lower ride height. For optimal usage, use with double eye springs.
Bestseller No. 4
LCI Lippert 3,500LB Straight Idler Trailer Axle 72HF 58SC
  • 72" from Hubface to Hubface and 58" Spring Center to Spring Center.
  • Springs are 25 1/4" long and 1 3/4" wide
  • 4 Leaf Springs
  • 2-3/8" Main Tube
  • 5 Lug with a 4 1/2" bolt pattern. 1/2 lug studs.
Bestseller No. 5
The Trailer Parts Outlet 3500 lb Light Duty Single Trailer Axle Kit with Suspension - Leaf Springs, Hanger & U-Bolt kit (89" Hubface - 74" Spring Center (6'4 Frame), 5x4.5 Bolt Pattern)
  • All-in-One Bundle: This 3.5K LD Single Axle trailer kit includes everything you need for a quick and easy installation, such as a 3.5k Idler Axle, double eye hanger kit, 4-Leaf Double Eye Springs, and 2 1.75k U-Bolt Kits
  • High Strength Construction - The high strength steel axle tube construction ensures a durable and long-lasting performance for small utility trailers, cargo trailers, ATV trailers, and more
  • High-Quality Parts - Made with OEM grade trailer axles and suspension, this kit is packed with high-temp axle grease for reliable performance
  • Low Ride Height - With an underslung design, the axle is welded with spring seats on the bottom, allowing for a lower ride height and improved stability
  • EZ Lube Design - Removable rubber plug allows for easy access to a grease-able zerk fitting, allowing you to grease your axle without having to remove the entire hub
Bestseller No. 6
The Trailer Parts Outlet - 2K-2000lb Idler Trailer Axle 5x4.5 Bolt Pattern - Light Duty Trailer Axle, Dexter Compatible, 71" Hubface-58 Spring Center
  • Underslung Design - Our trailer axle is underslung and Welded with Spring Seats on the Bottom - Provides a lower ride height for easier loading and unloading of your trailer
  • EZ Lube Design - These single trailer axle features a removable rubber plug on the hub cap - allows for easy grease access without the need to remove the entire hub, saving you time and hassle
  • Light Duty Trailer Axle - Designed for use on light duty trailers, utility, boat, car haulers, ATV, lawn & landscape, motorcycle, BBQ pit, cargo, enclosed, RV trailers and more
  • Internal Wiring System - The trailer axle comes with an internal wiring system that protects brake wires from wear and tear, ensuring a seamless design that is perfect for any trailer type
  • 5x4.5 Bolt Pattern - The 5 x 4.5 bolt pattern offers compatibility with a wide range of trailer wheels, providing flexibility and convenience for your trailer setup
SaleBestseller No. 7
VIRTIONZ Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1" Round BT8 Spindle -2pack
  • Trailer Axle Kits with 4 on 4" Bolt Idler Hub & 1"
  • 1,250 lb Hub Capacity, Used On 2,000 lb Axle Shaft 1 Diameter: 1 1/4" Shaft 2 Diameter: 1" Shaft Length: 8 3/4" (4" Long Stub) Hub A Diameter.: 2 1/2" Hub B Diameter: 5 1/2" Bolt Pattern: 4"
  • 2) Idler Hub with Lug Nuts, (2) 1" BT8 Round Spindle with Castle Nut, Pin & Washer, (4) Inner/Outer Bearings, (2) Double-lip Grease Seal (1 1/4" I.D. / 2" O.D.), (2) 2" Grease/Dust Cap
  • Assembly with 4 on 4" bolt idler hub & 1" round BT8 spindle. Rated to 1,250 lbs. each or 2,000 lbs. for the pair
Bestseller No. 8
Bestseller No. 9
The Trailer Parts Outlet - 3.5k TK Trailer Axle - 3500 lb Idler - (4" Drop), 73/00 (Loose Spring Seats) / 5x4.5 Bolt Pattern
  • 3,500 lbs TK Trailer Axle (3.5K Capacity), 5 x 4.5 Bolt Pattern, Tube: 2 3/8", Standard 4" Drop, Idler
Bestseller No. 10
The Trailer Parts Outlet - 3.5k TK Trailer Axle - 3500 lb Idler 5 Lug - Dexter Compatible, 89/74 Hubface/Spring Center - (6'4) Frame Width / 5x5 Bolt Pattern
  • Specs: 3,500 lbs Idler Trailer Axle (Capacity 3.5K), 5 Lug, Tube: 2 3/8"
  • High Strength Straight Steel Axle Tube
  • Axle comes fully assembled, so all you'll have to do is attach the springs, the U-bolt kits, and the tire and wheel assemblies.
  • Underslung - Spring seats are welded to the bottom of the axle, which allows for a lower ride height.
  • Trailer Axle Design for use on Light Duty Trailers

Last update on 2024-05-12 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

 


Leave a Comment

Share to...