“This site contains affiliate links for which OEMDTC may be compensated” |
March 16, 2022 NHTSA CAMPAIGN NUMBER: 22E020000
Cracked wheel spokes may damage the tires, causing a loss of vehicle control, and increasing the risk of a crash.
NHTSA Campaign Number: 22E020
Manufacturer Custom Wheel House LLC
Components WHEELS
Potential Number of Units Affected 116
Summary
Custom Wheel House LLC (Custom Wheel) is recalling certain Method Race Wheels, model MR316, part number MR31678060525, and size 17 x 8, +25 Offset, 6 x 5.5 (139.7) with casting lot markings “20C” and “13B.” The wheel spokes may experience cracking under heavy weight loads.
Remedy
Dealers will replace the wheels, free of charge. Owner notification letters were mailed March 24, 2022. Owners may contact Custom Wheel customer service at 1-866-779-8604.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
IMPORTANT SAFETY RECALL
March 24, 2022
NHTSA Campaign Number: 22E-020 Dear Customer,
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Reason for Notice
Custom Wheel House LLC has decided that a defect which relates to motor vehicle safety exists in certain Method Race Wheels MR316 wheels sold between November 1st 2021 to February 1st 2022.
BRAND | PART NUMBER | PRODUCT MODEL | SIZE AND OFFSET | BOLT PATTERN | FINISH |
METHOD RACE WHEELS | MR31678060525 | MR316 | 17X8 +25MM | 6X5.5IN
(6X139.7MM) |
MATTE BLACK |
Custom Wheel House LLC determined that defective wheels may experience cracking under extreme loads, i.e., vehicles with axle weights at or near the marked maximum load rating and using the maximum recommended tire diameter of 37 inches. This cracking is more likely to occur under extreme loads and may progress to the point of a wheel failure, which could lead to loss of vehicle control and increase risk of a crash. Custom Wheel House LLC will remedy the defect without charge and at no cost to the customer.
What Should You Do
Custom Wheel House LLC is recalling the subject wheels sold within the identified time frame. Upon receipt of this letter, you may immediately contact the dealer you purchased the wheels from to schedule replacement of the wheels. To ensure your safety and satisfaction with our product, we request that you return the recalled wheels and this letter to your dealer. Your wheels will be replaced with new wheels of same type and functionality.
Once contact has been made with your dealer, they will schedule a time to replace your wheels. The dealer will dismount the tires from your wheels. They will then install your tires on new wheels. The estimated time for the replacement is approximately 1-2 hours, but the service facility may need your vehicle for a longer period if scheduling issues arise.
Reimbursement
If wheels were replaced prior to notification of recall please contact Custom Wheel House at 866-779-8604 for information about how to be reimbursed for product and service.
Contact Information
Should any questions or problems arise with your wheels, please call Custom Wheel House at 866-779-8604 to speak with a representative. In the event you believe we have failed to or are unable to replace your wheels without charge to you, as described above, within 60 days after contacting your dealer or Custom Wheel House for replacement, you may submit a complaint to the
Administrator, National Highway Traffic Safety Administration,
1200 New Jersey Avenue, SE.,
Washington, DC 20590; or
call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153);, or go to https://www.safercar.gov
If you are a vehicle lessor, Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days of receiving the notification.
Please understand that we have taken this action in the interest of your safety and satisfaction with our wheels. We regret any inconvenience that this action may cause you.
Sincerely,
Custom Wheel House LLC
Chronology :
December 2021: pre-production sample part fails laboratory cornering fatigue test, which was informed to manufacturing partner to begin investigation, and the factory identified that a likely cause was the casting process not being optimized on pre-production parts.
January 2022: Production is halted, factory inventory quarantined, no shipments approved to leave factory, and the factory notified that some parts from the first production order failed laboratory cornering fatigue testing.
01/30/2022-02/08/2022: Factory shutdown for Chinese New Year February 2022: Based on review of US laboratory failures and factory work record, the failures are observed to only occur on wheels with 20C and 13B casting lots. Failures do not occur on wheels with any other casting lot identifications.
March 2022: Custom Wheel House notifies dealers of wheels with possible issue to begin gathering customer information.
1 Affected Product
Equipment
BRAND | PART NO. | PRODUCTION DATES |
METHOD RACE WHEELS | MR316 |
13 Associated Documents
Recall Acknowledgement
Defect Notice 573 Report
RCLRPT-22E020-1952.PDF 214.538KB
Recall 573 Report – 3/23/2022
RCLRPT-22E020-5059.PDF 214.623KB
ISSUED Owner Notification Letter(Part 577)
RCONL-22E020-7938.pdf 227.26KB
Manufacturer Notices(to Dealers,etc)
RCMN-22E020-4406.pdf 223.603KB
Recall Quarterly Report #2, 2022-2
RCLQRT-22E020-3500.PDF 211.277KB
Recall Quarterly Report #1, 2022-1
RCLQRT-22E020-9444.PDF 211.277KB
Recall Quarterly Report #1, 2022-1
RCLQRT-22E020-3554.PDF 211.114KB
Recall Quarterly Report #3, 2022-3
RCLQRT-22E020-3813.PDF 211.277KB
Recall Quarterly Report #4, 2022-4
RCLQRT-22E020-5192.PDF 211.391KB
Recall Quarterly Report #5, 2023-1
RCLQRT-22E020-8623.PDF 211.584KB
Recall Quarterly Report #6, 2023-2
RCLQRT-22E020-1142.PDF 211.584KB
Recall Quarterly Report #7, 2023-3
RCLQRT-22E020-3964.PDF 211.802KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22E020&docType=RCL
“This site contains affiliate links for which OEMDTC may be compensated” |
- SUPERIOR QUALITY 14G STAINLESS STEEL SPOKES FOR LONG TERM USE: These spokes are design to endure all biking conditions. They will not rust while chrome-plated steel does. They are also stronger and can resist corrosion better. Made in Europe.
- BRASS NIPPLE INCLUDED: High precision and quality nickel-plated brass nipples (silver color) are included. Nipple length : 14.6 mm
- PERFECT FOR REPLACEMENT OR BUILDING NEW WHEELS : It is suitable for 26 inch bike, 27-29 inch bike, 700c, MTB wheelset 26 inch. They also works for treking, road, city and E-bike. If you have problematic/lose spokes, then these can be used to repair. They are also great for building new wheelset for your dream bike, because you can choose your own hub and rims.
- AVAILABLE SIZE FROM 254-294 MM: The head is J-bend which mean it has 90-degree bend in the spoke head at one end, which leads it to resemble the letter J.
- WHAT SPOKE LENGTH DO I NEED: The length of spoke depends on dimension of hubs, rim and lacing pattern. You can use online spoke length calculator to determine it or simply consult with your wheel builder. For repair, you can simply remove a spoke from the wheel and measure its total length. You can use a conversion chart from inches to millimeters to order spokes.
- Enough Quantity: you will receive 216 pieces of bike spoke covers in 12 colors, including red, dark blue, light blue, dark green, light green, black, white, fluorescent, orange, purple, yellow and pink, adequate and various to meet your daily use and replacement needs
- Quality Material to Use: these spoke skins for dirt bikes are made of plastic, with high temperature resistance, reliable and lasting, not easy to fade, providing you with a nice experience
- Appropriate Size to Install: the dirt bike spoke covers measure about 24 cm/ 9.4 inches in length, lightweight and without increasing the burden to your bike; They are easy to install, you just need to measure the spoke length, and cut the spoke cover to the proper size, then open the slit on the side and press it in spoke, no glue or extra fasteners are required
- Decorative and Protective: these motocross spoke decorations can not only make your bike stylish and cool, but also effectively keep dirt and rust away from your bike spokes, to extend spokes' service life
- Widely Applicable: the plastic spoke protector is suitable for most brands and types of dirt bike, motorcycle, bicycles, mountain bike, road bike, folding bike, touring bike, kids bike, wheelchair and so on
- Package includes: 12 x 304 Stainless Steel Spokes + 12 x Nipples
- Made of high quality stainless steel, fine workmanship, environmental protection, electroplating surface, rust, corrosion resistance, long service life, durable
- Length: 260mm; Diameter: 0.2mm
- Type: 14G MTB Spoke
- Standard of spoke measurement: Distance from inner wall of elbow to top of other end
- Package includes: 12 x 14G MTB Spokes + 12 x 12mm Nipples
- Length: 290mm; Diameter: 2mm
- It is made of high-quality stainless steel, with fine workmanship, environmental protection, electroplated surface, rust prevention, corrosion resistance, long service life and durability
- Product: 14G MTB Spokes
- Spoke measurement standard: the distance from the inner wall of the elbow to the top of the other end
- Very beautiful luminous beads
- All standard bicycle spokes for any type of bicycle
- The luminous color bead is installed on the bicycle banner, which is very dazzling at night
- Easy to use, snap on,Round length 0.5"
- Package includes 108 round spoke beads
- Premium Material:Made of quality plastic, durable and not easy to deform and fade, designed with vivid color.Lightweight and portable.The bicycle spoke beads decoration would make an excellent way to decorate your bikes, and adding pleasure to your riding trip.
- Easy to Installation:Easy to snap the spoke beads on your children bicycle spokes and transform the wheels in seconds.Easy to install and remove,suitable for most standard type of bike spoke.Enough quantity and nice bicycle spoke decoration.
- Assorted Colors and Shapes:A variety of color design,simple and cute,is loved by children.The bicycle spoke beads in vivid and lively color can catch the attention easily and light up the kid's moods.Except decor your bicycle. It is not only makes you been seen safely on roads and also increases your rate of second glance when riding.
- Ideal Festival Gift:It's perfect as gifts for kids,such as children's day, Halloween, Christmas, Easter, birthday, New Year etc.Beautiful and practical decoration,make your bike more attractive and stylish.
- Wide Application:The spoke beads are both suitable for the front and back wheels of the bicycle; your kids will have the coolest bikes.Suitable for decorating bicycle and helping to cultivate child's hands-on skills.
- 12 inch Spokes have good toughness and well anti impact resistance, reduce the impact resistance of wheel.
- Fit for SSR 50cc 125cc 150cc XR CRF Chinese Dirt Pit Bike Front Or Rear 2.5-12 3.00-12 80/100-12 Wheel Rims Hub motorcycles.
- Wheel spoke kit includes enough spokes(36 pcs) to rebuild your motorcycle wheel.
- package incloud:36pcs spokes,1 pcs Inner tube protective strip
- pls check your Tire and rim size before buying ,the spoke fits Front 2.75-12 Rear 3.00-12 80/100-12 Tire Wheel and C Style Rim Hub Only
- Material: Stainless Steel, 9H hardness
- Size: Circular spoke wrench: 1.57'' x 1.57''x 0.47''; 14Model Spoke Wrench: 2'' x 1.45''x 0.53''
- Bicycle spoke wrench, must-have tool for adjusting the spokes to be tightened and correct the deformation of the rim.
- Suitable for spoke nipple sizes 10, 11, 12, 13, 14, 15.
- Portable: Small and lightweight, weighting 1.94 oz.
- Package included 108 pcs round spoke bead,Assorted Colors
- All standard bicycle spokes for any type of bicycle
- Make your bike look more special
- Easy to use, snap on,Round length 0.5"
- Great for decorating your kid's bike
Last update on 2024-04-15 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
IMPORTANT SAFETY RECALL
March 24, 2022
NHTSA Campaign Number: 22E-020
Dear Customer,
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Reason for Notice
Custom Wheel House LLC has decided that a defect which relates to motor vehicle safety exists in certain Method Race Wheels MR316 wheels sold between November 1st 2021 to February 1st 2022.
BRAND
PART NUMBER
PRODUCT MODEL
SIZE AND OFFSET
BOLT PATTERN
FINISH
METHOD RACE WHEELS
MR31678060525
MR316
17X8 +25MM
6X5.5IN (6X139.7MM)
MATTE BLACK
Custom Wheel House LLC determined that defective wheels may experience cracking under extreme loads, i.e., vehicles with axle weights at or near the marked maximum load rating and using the maximum recommended tire diameter of 37 inches. This cracking is more likely to occur under extreme loads and may progress to the point of a wheel failure, which could lead to loss of vehicle control and increase risk of a crash. Custom Wheel House LLC will remedy the defect without charge and at no cost to the customer.
What Should You Do
Custom Wheel House LLC is recalling the subject wheels sold within the identified time frame. Upon receipt of this letter, you may immediately contact the dealer you purchased the wheels from to schedule replacement of the wheels. To ensure your safety and satisfaction with our product, we request that you return the recalled wheels and this letter to your dealer. Your wheels will be replaced with new wheels of same type and functionality.
Once contact has been made with your dealer, they will schedule a time to replace your wheels. The dealer will dismount the tires from your wheels. They will then install your tires on new
wheels. The estimated time for the replacement is approximately 1-2 hours, but the service facility may need your vehicle for a longer period if scheduling issues arise.
Reimbursement
If wheels were replaced prior to notification of recall please contact Custom Wheel House at 866-779-8604 for information about how to be reimbursed for product and service.
Contact Information
Should any questions or problems arise with your wheels, please call Custom Wheel House at 866-779-8604 to speak with a representative. In the event you believe we have failed to or are unable to replace your wheels without charge to you, as described above, within 60 days after contacting your dealer or Custom Wheel House for replacement, you may submit a complaint to the
Administrator, National Highway Traffic Safety Administration,
1200 New Jersey Avenue, SE.,
Washington, DC 20590; or
call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153);, or go to http://www.safercar.gov
If you are a vehicle lessor, Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days of receiving the notification.
Please understand that we have taken this action in the interest of your safety and satisfaction with our wheels. We regret any inconvenience that this action may cause you.
Sincerely,
Custom Wheel House LLC
**************************************************************************************************************
IMPORTANT SAFETY RECALL
March 24, 2022
NHTSA Campaign Number: 22E-020
Dear Dealer or Distributor,
Reason for Notice
Custom Wheel House LLC has decided that a defect which relates to motor vehicle safety may exist in certain Method Race Wheels MR316 wheels identified as below, which were sold between November 1st 2021 to February 1st 2022.
BRAND
PART NUMBER
PRODUCT MODEL
SIZE AND OFFSET
BOLT PATTERN
FINISH
METHOD RACE WHEELS
MR31678060525
MR316
17X8 +25MM
6X5.5IN (6X139.7MM)
MATTE BLACK
Custom Wheel House LLC determined that defective wheels may experience cracking under extreme loads, i.e., vehicles with axle weights at or near the marked maximum load rating and using the maximum recommended tire diameter of 37 inches. This cracking is more likely to occur under extreme loads.
What Should You Do
Custom Wheel House LLC is recalling the subject wheels sold within the identified time frame. To ensure customer safety and satisfaction with our product, we request your assistance with customers’ return and replacement of the recalled wheels. Customers have been instructed to contact their dealer to schedule replacement of the subject wheels at no cost to them, including service. Custom Wheel House LLC will remedy the defect without charge and at no cost to the dealer as well. Replacement parts are currently available.
Custom Wheel House LLC also requests your assistance with the replacement procedures, including dismounting the tires from the customer’s wheels and installing the customer’s tires on new replacement wheels. We have advised customers that the estimated time for the replacement is approximately 1-2 hours.
Please be advised that it is a violation of Federal law for a dealer to deliver any new or used item of motor vehicle equipment covered by this notification under a sale or lease until this defect is remedied.
Should any questions or problems arise, please call Custom Wheel House at 866-779-8604 to speak with a representative.
Sincerely,
Custom Wheel House LLC
**************************************************************************************************************
OMB Control No.: 2127-0004
Part 573 Safety Recall Report 22E-020
The information contained in this report was submitted pursuant to 49 CFR §573
Manufacturer Name : Custom Wheel House LLC
Submission Date : MAR 23, 2022
NHTSA Recall No. : 22E-020
Manufacturer Recall No. : NR
Manufacturer Information :
Manufacturer Name : Custom Wheel House LLC
Address : 15500 Cornet St
Santa Fe Springs CA 90670
Company phone : 8667798604
Population :
Number of potentially involved : 116
Estimated percentage with defect : 50 %
Equipment Information :
Brand / Trade 1 : Method Race Wheels
Model : MR316
Part No. : MR31678060525
Size : 17×8, +25 Offset, 6×5.5(139.7)
Function : Wheel Rim
Descriptive Information : The recall population includes MR31678060525 wheels received and sold
between 11/01/2021 to 02/01/2022 with casting lot markings of “20C” and
“13B”. The quantity of wheels that may contain those casting lots is 389. The
quantity of wheels sold in that time is 116. The recall population was determined
based on factory work record and product quality control markings identifying
casting date and casting lot number on the wheels.
Production Dates : OCT 14, 2021 – NOV 18, 2021
Description of Defect :
Description of the Defect : Custom Wheel House LLC observed during a routine audit test that subject
wheels exhibited cracking in the spokes when subject to the cornering fatigue
test, conducted pursuant to SAE J2530. The wheel may experience cracking
under extreme loads, i.e. vehicles with axle weights at or near the marked
maximum load rating and using the maximum recommended tire diameter of
37 inches.
FMVSS 1 : NR
FMVSS 2 : NR
Description of the Safety Risk : The safety risk is of the wheel cracking under extreme loads and maximum
ratings, as described. While precise safety-related-risk cannot be quantified
with certainty there is risk of causing a vehicle crash, Custom Wheel House
will conduct a recall out of abundance of caution.
Part 573 Safety Recall Report 22E-020 Page 2
The information contained in this report was submitted pursuant to 49 CFR §573
Description of the Cause : Factory labor error and mold cooling issue resulted in inferior material
mechanical properties.
Identification of Any Warning
that can Occur :
NR
Involved Components :
Component Name : Wheel Rim
Component Description : MR316, 17×8, +25mm offset, 6×5.5(139.7), Matte Black
Component Part Number : MR31678060525
Supplier Identification :
Component Manufacturer
Name : Shandong Jinma Automotive Equipment
Address : 206 National Road, Luozhuang District
Linyi City Foreign States
Country : China
Chronology :
December 2021: pre-production sample part fails laboratory cornering fatigue test, which was informed to
manufacturing partner to begin investigation, and the factory identified that a likely cause was the casting
process not being optimized on pre-production parts.
January 2022: Production is halted, factory inventory quarantined, no shipments approved to leave factory,
and the factory notified that some parts from the first production order failed laboratory cornering fatigue
testing.
01/30/2022-02/08/2022: Factory shutdown for Chinese New Year
February 2022: Based on review of US laboratory failures and factory work record, the failures are observed to
only occur on wheels with 20C and 13B casting lots. Failures do not occur on wheels with any other casting lot
identifications.
March 2022: Custom Wheel House notifies dealers of wheels with possible issue to begin gathering customer
information.
Part 573 Safety Recall Report 22E-020 Page 3
The information contained in this report was submitted pursuant to 49 CFR §573
Description of Remedy :
Description of Remedy Program : At no cost to the customer, replace subject wheels and service to replace
them. If remedy was handled prior to recall owners can mail invoice to
Custom Wheel House or call 866-779-8604 for reimbursement.
How Remedy Component Differs
from Recalled Component :
Remedy components will have manufacture dates and casting lot numbers
that do not match the affected product. The replacement wheels will not
experience cracking of the spokes under the extreme loads described
previously.
Identify How/When Recall Condition
was Corrected in Production :
This was an isolated incident that involved an issue with a mold cooling
system and worker not following work instructions. Internal corrective
actions, including quarantining all affected inventory parts, have been
made at the manufacturing site to prevent re-occurrence.
Recall Schedule :
Description of Recall Schedule : Owners and dealers will be notified starting March 23, 2022, 5 business
days from the submission of this report as required per 577.5. To
facilitate the recall process, Custom Wheel House will perform enhanced
outreach to affected customers and dealers by direct phone and email
communications as follow-up and as necessary.
Planned Dealer Notification Date : MAR 24, 2022 – NR
Planned Owner Notification Date : MAR 24, 2022 – NR
Purchaser Information :
The following manufacturers purchased this defective/noncompliant equipment for possible use or
installation in new motor vehicles or new items of motor vehicle equipment:
Name : NR
Address : NR
NR
Country : NR
Company Phone : NR
* NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004
Part 573 Safety Recall Report 22E-020
The information contained in this report was submitted pursuant to 49 CFR §573
Manufacturer Name : Custom Wheel House LLC
Submission Date : MAR 16, 2022
NHTSA Recall No. : 22E-020
Manufacturer Recall No. : NR
Manufacturer Information :
Manufacturer Name : Custom Wheel House LLC
Address : 15500 Cornet St
Santa Fe Springs CA 90670
Company phone : 8667798604
Population :
Number of potentially involved : 116
Estimated percentage with defect : NR
Equipment Information :
Brand / Trade 1 : Method Race Wheels
Model : MR316
Part No. : MR31678060525
Size : 17×8, +25 Offset, 6×5.5(139.7)
Function : Wheel Rim
Descriptive Information : The recall population includes MR31678060525 wheels received and sold
between 11/01/2021 to 02/01/2022 with casting lot markings of “20C” and
“13B”. The quantity of wheels that may contain those casting lots is 389. The
quantity of wheels sold in that time is 116. The recall population was determined
based on factory work record and product quality control markings identifying
casting date and casting lot number on the wheels.
Production Dates : OCT 14, 2021 – NOV 18, 2021
Description of Defect :
Description of the Defect : Custom Wheel House LLC observed during a routine audit test that subject
wheels exhibited cracking in the spokes when subject to the cornering fatigue
test, conducted pursuant to SAE J2530. The wheel may experience cracking
under extreme loads, i.e. vehicles with axle weights at or near the marked
maximum load rating and using the maximum recommended tire diameter of
37 inches.
FMVSS 1 : NR
FMVSS 2 : NR
Description of the Safety Risk : The safety risk is of the wheel cracking under extreme loads and maximum
ratings, as described. While precise safety-related-risk cannot be quantified
with certainty, Custom Wheel House will conduct a recall out of abundance of
caution.
Part 573 Safety Recall Report 22E-020 Page 2
The information contained in this report was submitted pursuant to 49 CFR §573
Description of the Cause : Factory labor error and mold cooling issue resulted in inferior material
mechanical properties.
Identification of Any Warning
that can Occur :
NR
Involved Components :
Component Name : Wheel Rim
Component Description : MR316, 17×8, +25mm offset, 6×5.5(139.7), Matte Black
Component Part Number : MR31678060525
Supplier Identification :
Component Manufacturer
Name : Shandong Jinma Automotive Equipment
Address : 206 National Road, Luozhuang District
Linyi City Foreign States
Country : China
Chronology :
December 2021: pre-production sample part fails laboratory cornering fatigue test, which was informed to
manufacturing partner to begin investigation, and the factory identified that a likely cause was the casting
process not being optimized on pre-production parts.
January 2022: Production is halted, factory inventory quarantined, no shipments approved to leave factory,
and the factory notified that some parts from the first production order failed laboratory cornering fatigue
testing.
01/30/2022-02/08/2022: Factory shutdown for Chinese New Year
February 2022: Based on review of US laboratory failures and factory work record, the failures are observed to
only occur on wheels with 20C and 13B casting lots. Failures do not occur on wheels with any other casting lot
identifications.
March 2022: Custom Wheel House notifies dealers of wheels with possible issue to begin gathering customer
information.
Part 573 Safety Recall Report 22E-020 Page 3
The information contained in this report was submitted pursuant to 49 CFR §573
Description of Remedy :
Description of Remedy Program : At no cost to the customer, replace subject wheels and service to replace
them.
How Remedy Component Differs
from Recalled Component :
Remedy components will have manufacture dates and casting lot numbers
that do not match the affected product. The replacement wheels will not
experience cracking of the spokes under the extreme loads described
previously.
Identify How/When Recall Condition
was Corrected in Production :
This was an isolated incident that involved an issue with a mold cooling
system and worker not following work instructions. Internal corrective
actions, including quarantining all affected inventory parts, have been
made at the manufacturing site to prevent re-occurrence.
Recall Schedule :
Description of Recall Schedule : Owners and dealers will be notified starting March 23, 2022, 5 business
days from the submission of this report as required per 577.5. To
facilitate the recall process, Custom Wheel House will perform enhanced
outreach to affected customers and dealers by direct phone and email
communications as follow-up and as necessary.
Planned Dealer Notification Date : MAR 23, 2022 – NR
Planned Owner Notification Date : MAR 23, 2022 – NR
Purchaser Information :
The following manufacturers purchased this defective/noncompliant equipment for possible use or
installation in new motor vehicles or new items of motor vehicle equipment:
Name : NR
Address : NR
NR
Country : NR
Company Phone : NR
* NR – Not Reported
SEOCONTENT-END