“This site contains affiliate links for which OEMDTC may be compensated” |
October 16, 2020 NHTSA CAMPAIGN NUMBER: 20V641000
Body Mount Bracket May Rub Brake Line
If the bracket rubs through the brake lines, braking ability may be negatively affected, increasing the risk of a crash.
NHTSA Campaign Number: 20V641
Manufacturer Shyft Group
Components SERVICE BRAKES, HYDRAULIC
Potential Number of Units Affected 323
Summary
Shyft Group is recalling certain 2021 Utilimaster Aeromaster vehicles built on Ford E-450 chassis. The body mount bracket may chafe the brake lines, eventually rubbing through the brake lines.
Remedy
Shyft Group has notified owners, and dealers will inspect the brake line and body mount brackets for adequate clearance, depending on the revision level of body mount bracket installed on the vehicle, a new bracket may need to be installed, free of charge. Any damaged brake lines would be replaced. The recall began October 16, 2020. Owners may contact Shyft Group customer service at 1-800-582-3454. Shyft Group’s number for this recall is 20-10.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
1 Affected Product
Vehicle
MAKE | MODEL | YEAR |
UTILIMASTER | AEROMASTER | 2021 |
6 Associated Documents
Recall Quarterly Report #3, 2021-2
RCLQRT-20V641-6364.PDF 211.309KB
Defect Notice 573 Report
RCLRPT-20V641-8100.PDF 213.431KB
Recall Acknowledgement
RCAK-20V641-5758.pdf 244.509KB
Recall Quarterly Report #1, 2020-4
RCLQRT-20V641-4063.PDF 211.125KB
Recall Quarterly Report #2, 2021-1
RCLQRT-20V641-7417.PDF 211.22KB
Recall Quarterly Report #4, 2021-3
RCLQRT-20V641-5788.PDF 211.411KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V641&docType=RCL
- Provides an extra margin of safety in extreme braking conditions
- Mix of polyglycol ethers ensures hot brake-system operation will not create dangerous vapor
- Excellent for ABS, disc and drum brake systems
- Delivers braking power when needed by avoiding a spongy pedal
- Both wet and dry boiling points exceed the minimum government standards
- High quality blend of polyethylene glycol ethers and additives
- Compatible with all brake system rubber components and other brake fluids
- Prevents seal hardening or softening
- Protects against rust and corrosion
- Provides excellent lubricity
- High compatibility. Use with or direct replacement for DOT 3, DOT 4, and DOT 5. 1
- Extended Service Interval (ESI): Lasts 100% longer than DOT 3, 50% longer than DOT 4, and 10% longer than DOT 5. 1
- Exceeds all DOT 3, DOT 4, and DOT 5. 1 standards
- Wet boiling point ~ 365 DegreeF/Viscosity at -40 DegreeC ~ 685mm2/s
- Standard brake fluid has a recommended change interval of 2 years. The recommended change interval for Bosch ESI6 is 3 years.
- Premium DOT 3 Brake Fluid has a minimum boiling point of 450°F
- Meets and exceeds DOT 3 and all other Federal and SAE specifications and standards for motor vehicle brake fluids
- Mixes with all DOT 3 approved brake fluids
- Designed for use in disc, drum and ABS brake systems
- Synthetic quality brake fluid
- Contains special ingredients to guard against vapor lock and moisture absorption
- Exceeds requirements for both DOT 3 and DOT 4 brake fluids
- Specially formulated for DOT 4 brake fluid applications
- Designed for use in disc, drum and ABS brake systems
- Premium brake and hydraulic clutch fluid that protects internal components from corrosion under normal use
- High boiling point to minimize brake fluid boiling and vapor lock
- Excellent low temperature capability and stability when used where lower cold viscosities are required
- Excellent low temperature capability and stability when used where lower cold viscosities are required
- The 336⁰F wet boil point and 521⁰F dry boil point exceeds common characteristics for DOT 4 brake fluids
- Provides corrosion protection in brake components
- Matches needs of all DOT 4 manufacturer recommendations
- Compatible with all DOT 3 and DOT 4 applications
- Minimal decrease of boiling point due to excellent water locking properties
- Non-foaming when filling and bleeding the brake system
- Excellent corrosion protection due to selected additives
- High safety tolerance against steam bubbles
- Makes brake fluid changing intervals of up to 3 years possible
- 2 Pack
- Dry boiling point 594 degrees F
- Motul 600 brake fluid is 100 percent synthetic and has an extremely high boiling poin
- Helping to prevent vapor lock and brake fade during hard use
- This brake fluid exceeds both DOT 3 and DOT 4 specifications
Last update on 2024-04-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.