RC000206 – BIM/BIR Is Not Watertight – 2020-2021 Thor Motor Coach Daybreak, Four Winds, Chateau, Freedom Elite, Quantum Motorhomes

“This site contains affiliate links for which OEMDTC may be compensated”

November 17, 2020 NHTSA CAMPAIGN NUMBER: 20V711000

BIM/BIR Is Not Watertight

Water may get into the BIM/BIR and create electrical arcing, increasing the risk of a fire.

 

NHTSA Campaign Number: 20V711

Manufacturer Thor Motor Coach

Components ELECTRICAL SYSTEM

Potential Number of Units Affected 1,074

 

Summary

Thor Motor Coach (TMC) is recalling certain 2020-2021 Daybreak, Four Winds, Chateau, Freedom Elite, Quantum motorhomes built on a Chevrolet chassis. The BIM (Battery Isolation Manager)/BIR (Battery Isolation Relay) is not watertight when exposed to engine compartment heat.

 

Remedy

TMC will notify owners, and dealers will replace the BIM/BIR with a Trombetta solenoid, free of charge. The recall began January 13, 2021. Owners may contact TMC customer service at 1-877-855-2867. TMC’s number for this recall is RC000206.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 


Issue:

It has been discovered that on certain model year 2020/2021 Chateau, Daybreak, Four Winds, Freedom Elite, and Quantum Motorhomes built on a Chevy chassis, expansion and contraction of the plastic body of the BIM (battery Isolation Manager)/BIR (Battery Isolation Relay) from heat in the engine compartment causes it to be susceptible to moisture inside the body, which in turn produces arcing of the internal components. This internal arcing can cause heating, or the possibility of a fire.

 

Shop Supplies Needed:

(3) ¼” self tapping screw

(4) #8 self tapping pan head screws

(1) ¼” star washer

 

Tools Required:

½” socket for torque wrench (for battery cables)

3/8” screw gun bit (for ¼” self tapping screws)

5/16” socket (to remove overflow bottle)

Electrical Tape

Heat gun

Screw Gun

Square head screw gun bit (for #8 self tapping screws)

Torque Wrench

Wire cutters

Wire Crimpers

 

YouTube Video Instructions Found Here:

YouTube video

 

Disclaimer– Video is for installation of recall repair on a Ford Chassis. Steps will vary for Chevy Chassis.

 

Instructions:

1. Disconnect battery cable on the negative post of the house battery located in the step well.

2. Disconnect battery cable from negative post of the chassis battery located under the hood.

3. Locate BIM/BIR mounted on passenger’s side inside fender.

4. Remove the chassis battery cable and the house battery cable from the BIM/BIR and remove BIM/BIR.

Note: The BIM/BIR needs to be returned to Thor Motor Coach for payment of the recall repairs.

5. Remove the screws holding the BIM/BIR to the inside fender.

6. Remove ground wire

7. Open the loom for the dash switch, locate the white and white with black tracer. Cut both wires.

8. Open the loom for the ignition power, locate the yellow wire and cut.

9. Find a good clearance where BIM/BIR was installed to mount the Trombetta solenoid. Make sure it is far away enough from the solenoid installed on fender below where the BIM/BIR was installed to avoid sparking.

10. Start a ¼” self-tapping hex head screw at the installation mark on the fender wall. Slide Trombetta solenoid bracket into place on the self-tapping hex head screw and secure.

11. Install a ¼” self-tapping hex head on the other side of the bracket of the Trombetta solenoid.

12. Install ground wire, black wire with ring terminal, above Trombetta solenoid on the inside of the fender by using a ¼” self-tapping hex head using a 3/8” bit. NOTE: Must use a star washer between the ring terminal and fender.

13. Mount the Isolater Relay Delay (IRD) beside the Trombetta solenoid and along the seam of the fender with 1-2 – #8 self-tapping pan head screws.

14. Verify which cable is coming from the chassis battery by tracing is back to the chassis battery. Remove the washer and nut from the Trombetta solenoid and secure the chassis battery cable to the large terminal post of the Trombetta solenoid closest to the firewall with the washer and nut.

Note: If either battery cable ring terminal is bent –– straighten before securing.

15. Secure the house battery cable to the other large terminal post (towards the front) of the Trombetta solenoid – this house battery is to be secured together with the white wire of the emergency start switch. Put the battery cable on the post first, then place the white wire on top and secure with washer and nut.

16. Tighten nuts on both battery cables using a torque wrench to 45 inch lbs.

17. Locate and cut yellow ignition power wire, strip back, and connect to yellow wire w/ yellow butt connector from the fuse holder. Crimp and heat shrink using a torch or electric heat gun. Using electrical tape, tape both ends of the yellow wires.

18. Locate cut white wire and white with black tracer from the emergency start switch and strip back both wires. Connect white wires with white butt connector and white with black wires white with black butt connector. Crimp both wires and heat shrink.

Use electrical tape to tape both ends of the wires.

19. Zip tie fuse holders and wires together as shown below to keep secure.

20. Reconnect house battery cable in the step well.

21. Reconnect chassis battery cable under the hood.

22. Test the emergency start switch by pushing the switch and listen for an audible clicking noise. This indicates the connection is proper. If you do not hear the clicking noise, check fuse holder and wire connections (white & white with black wires).

23. Start the engine, after 15-20 seconds, you should hear an audible clicking noise. This indicates the connection is proper. If you do not hear the clicking noise, check fuse holder and yellow wire connections.

 



10 Affected Products

Vehicles

MAKE MODEL YEAR
THOR MOTOR COACH CHATEAU 2020-2021
THOR MOTOR COACH DAYBREAK 2020-2021
THOR MOTOR COACH FOUR WINDS 2020-2021
THOR MOTOR COACH FREEDOM ELITE 2020-2021
THOR MOTOR COACH QUANTUM 2020-2021

 


10 Associated Documents

ISSUED Owner Notification Letter(Part 577)

RCONL-20V711-5835.pdf 37.282KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [36.41 KB]

 


Manufacturer Notices(to Dealers,etc)

RCMN-20V711-3148.pdf 139.258KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [135.99 KB]

 


Remedy Instructions and TSB

RCRIT-20V711-7005.pdf 2534.907KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.42 MB]

 


Remedy Instructions and TSB

RCRIT-20V711-8742.pdf 2534.907KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.42 MB]

 


Manufacturer Notices(to Dealers,etc)

RCMN-20V711-5278.pdf 139.258KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [135.99 KB]

 


Recall Quarterly Report #1, 2021-1

RCLQRT-20V711-3913.PDF 211.126KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.18 KB]

 


Recall Quarterly Report #2, 2021-2

RCLQRT-20V711-2837.PDF 211.227KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.28 KB]

 


Recall Acknowledgement

RCAK-20V711-6932.pdf 244.877KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [239.14 KB]

 


Defect Notice 573 Report

RCLRPT-20V711-4134.PDF 217.757KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [212.65 KB]

 


Recall Quarterly Report #3, 2021-3

RCLQRT-20V711-3182.PDF 211.311KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.36 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V711&docType=RCL

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
SaleBestseller No. 1
Stinger SGP32 200 AMP Battery Relay Isolator and Relay
Bestseller No. 2
Stinger SGP38 80-AMP Battery Isolator and Relay,BLACK
Bestseller No. 3
500 Amp Battery Isolator for Mobile Audio Relay Continuous Battery Isolator, 12v Battery Disconnect Relay 500A Relay and Isolator
  • 500 AMP BATTERY ISOLATOR - Perfect for any application with multiple batteries that need to be isolated including Marine, Mobile Audio, Off-Road, Power Sports, etc. | battery disconnect relay is used to isolate the second battery which powers audio, visual navigation, or other equipment.
  • POWERFUL FUNCTION - 12v battery isolator can continuously power handling 500 amps at 12V and handling of 700 amps at surge power | Doesn't create a voltage drop to your second battery unlike common isolators do. battery isolator 500 amp with a maximum current transfer, power on demand.
  • ELIMINATES BATTERY DRAIN - Normally, when two car batteries are connected in parallel, they are easy to charge and discharge each other | The relay battery isolator stops the battery bank from getting power from each one, eliminating that negative effect | Reducing the natural consumption of batteries after power off, lengthens the life of the primary battery.
  • FEATURE- Battery isolator solenoid is made of high-quality materials, excellent performance, and durability. Easy to install and start up immediately.
  • ONE YEAR SERVICE - The Mobile Audio Continuous Relay comes with 1 Year Warranty | Any problem please feel free to contact us for a replacement.
Bestseller No. 4
AFEISOL 500 Amp Battery Isolator and Relay for Marine, Mobile Audio, Off-Road, Power Sports 12V Mobile Audio Relay Battery Isolator
  • 【500 AMP BATTERY ISOLATOR】The 500 Amp Battery Isolator is designed to isolate a second battery or applications where multiple batteries need to be isolated, making it ideal for audio, navigation, winches, generators, etc., without dropping the voltage of the second battery as traditional isolators do while preventing the main battery from discharging.
  • 【PREMIUM QUALITY】500 Amp Battery Isolator Audio Relay uses high quality copper coiled wire to dramatically increase electrical and thermal resistance while extending service life, meets or exceeds OEM standards, and is endurance-tested for extreme environments.
  • 【HIGH CURRENT ISOLATOR】The rated voltage of this battery isolator is 12V, it can provide 500A constant current stably under 12V voltage, and 700A under surge power, which is upgraded on the traditional isolator, and it will not cause voltage drop to other batteries except the main battery.
  • 【KEY FEATURES】Prevent the main battery from discharging, when the main and secondary batteries are connected in series, it is easy to affect each other when charging and discharging, when your engine starts the battery isolator can connect the two batteries together and isolate them when the engine is turned off, which reduces the second battery's natural loss to the main battery and prolongs the service life of the main battery.
  • 【ONE YEAR WARRANTY】12V mobile audio relay battery isolator one year warranty is included in your purchase, if you have any questions about your purchase you can contact us at any time and we will get back to you within 24 hours!
Bestseller No. 5
Stinger SGP35 500-AMP Relay and Isolator , Black
  • 500 AMP High Current Relay/Isolator
  • Prevents primary battery discharge
  • Power on demand
  • Extends battery life
  • Universal 12 volt applications
Bestseller No. 6
MaySpare 200 Amp Mobile Audio Continuous Relay and Battery Isolator High Current Relay 12VDC
  • Function: An isolator is used to combine two batteries when a alternator is charging ( engine running) and isolate them when not charging ( engine off) so you can still start your vehicle
  • Voltage: 12VDC/ Dimensions: 2-3/8"W x 2-3/8"D x 3-3/4"H/Power Handling: Continuous power handling of 200 amps/ Surge Power Handling: 300 amps
  • Advantage: Does not create a voltage drop to the second battery like conventional isolators
  • Wrie Diagram : Connect the two small studs one to ground the other to an ignition on source from fuse box , the order on the large/ small studs does not matter
  • 100% OEM matching and high quality, direct replacement
Bestseller No. 7
500 Amp Battery Isolator for Mobile Audio Relay 12V Relay 12Volt Battery Disconnect Relay and Isolator
  • 【Signification】100,000 mechanical cycle life; 500A constant. Compatible with all types of alternators and charging systems.
  • 【Package Includes】1 x 500 Amp 12V Relay Battery Isolator.
  • 【Features】Great for isolating a second battery, making it dedicated to the stereo system, winch, generator, starter, and more. Does not create a voltage drop to the second battery like conventional isolators or prevents primary battery discharge.
  • 【Features】Prevents primary battery discharge; Maximum current transfer ; Ideal for 2nd audio battery isolation from vehicle systems. Please properly verify the year, make, model before purchasing.
  • 【Buy with Confidence】We will offer you 24 hours customer service. We have been struggling to offer satisfatory shopping experience for you. If there are any questions, please feel free to contact us and we will be honored to serve
Bestseller No. 8
Recoil SRL500 Microprocessor Controlled 500A Smart Battery Isolator and High Current Starter Relay, Dual Sensing Smart Relay, with Ring Terminals
  • SRL500 handles 500 Amps continuous at 12V and 700 Amps Surge. Microprocessor-controlled smart relay does not create a voltage drop to the second battery like conventional isolator.
  • Eliminates multiple battery drain as it stops battery bank from getting power from each one and extends battery life. Prevents the equipment from discharging the main battery when it is operated while the engine is off.
  • Once the main battery reaches 13.2V, the smart relay connects two batteries. Once the system drops below 12.7V, it disconnects two batteries.
  • The dual sensing feature allows charging both ways if auxiliary battery is charged by external power source. A waterproof manual override switch allows you to connect two batteries with the push of a button for 60 seconds.
  • Excellent waterproof performance, high quality in any weather conditions. Two 1/0AWG copper ring terminals and heat shrink tubing are included for easy installation.
Bestseller No. 9
VEVOR Split Charge Relay Kit, 6mtr 12V, Automatic Dual Battery Isolator Kit with 140AMP Voltage Sense Relay VSR, Compatible with RV Marine Car Vehicle Truck Caravan Camper Yacht ATV UTV Boats Workshop
  • Dual Battery Isolator: The smart battery isolator cuts in at 13.3 volts and cuts out at 12.8 volts to ensure your primary battery is always charged and ready to start your vehicle. It can charge two batteries simultaneously and isolate them from each other when the vehicle is turned off.
  • Easy to Install: This split charge relay kit comes with complete accessories, allowing you to start installing directly without purchasing additional components. Besides, we have detailed instructions for you to complete the installation easily and flawlessly.
  • Rugged & Durable: Split charge relay is made of a premium plastic material, which is shockproof and dustproof, ensuring maximum strength and durability for long-lasting usage. You will always be prepared and confident to take on any challenge.
  • Superb IP65 Waterproof: Voltage sensitive relay is waterproof up to IP65, which means that your isolator is secure for use even in dusty, wet, and unexpected extreme weather environments. Great for extreme vibration applications as well.
  • Fit Various Vehicles: This isolator kit 12v has a compact size of 2.66" x 2.11" x 2.66", suitable for almost anywhere. Mainly used in off-road vehicles, camper vans, RVs, caravans, 4x4s, leisure vehicles, ships, yachts, marine applications, etc.
Bestseller No. 10
NVX BIR500 500 AMP Battery Relay Isolator and Relay for Cars, RVs, ATVs, UTVs, and Boats.
  • 500 Amps at 12V Continuous Power Handling
  • 700 Amps Surge Power Handling
  • Switching Power: 10 - 16 VDC
  • Draws Less Than 1 Amp When On
  • Mobile Audio Relay and Battery Isolator

Last update on 2024-04-17 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...