“This site contains affiliate links for which OEMDTC may be compensated” |
May 24, 2022 NHTSA CAMPAIGN NUMBER: 22V370000
Inoperable vehicle lighting can reduce visibility and increase the risk of a crash.
NHTSA Campaign Number: 22V370000
Manufacturer Braun Ambulances
Components ELECTRICAL SYSTEM, EQUIPMENT
Potential Number of Units Affected 4
Summary
Braun Ambulances is recalling certain 2021 Chief XL Type I, 2020 TLC, and Express Plus ambulances. An additional resistor was incorrectly installed on the printed circuit board, which can disrupt CAN network communication and cause vehicle lighting to fail.
Remedy
Braun Ambulances will replace the modules, free of charge. Owner notification letters were mailed on June 20, 2022. Owners may contact Braun Ambulances’ customer service at 1-877-344-9990.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
IMPORTANT SAFETY RECALL
This notice applies to your vehicle, 3C7WRNCL9NG186467
Braun Recall Notice: 22V370
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Braun Industries has decided a safety related defect may exist with some Weldon Hercules HC 1.5 I/O Nodes, Weldon Part Number 6060-1000-00, produced between April 21, 2022, and April 29, 2022.
In the affected products, Weldon installed a termination resistor on the circuit board. In this configuration and when combined with external resistors located in a harness or with multiple nodes that do not have external resistors, CAN communication may become compromised which can impact any of the electrical loads that are connected to the CAN, including vehicle lighting, potentially increasing the risk of a crash. Since V-MUX systems are configured to match user needs, some installations may not present an issue at initial acceptance test, but nevertheless should be remedied. You are receiving this notice because Braun records indicate you have received shipments of affected units.
Braun will remedy the affected units free of charge by replacing them with Hercules HC 1.6 that has the same functionality as the Hercules 1.5 but does not include the internal terminator resistor. Replacement Hercules
HC 1.6 I/O Nodes are available as of May 15th, 2022. Replacement is done by removing the affected Hercules HC 1.5 I/O Nodes and installing Hercules HC 1.6 I/O Nodes. Replacement labor for each node replacement is 15 minutes per node. Nodes will require OEM programming which can be done by USB thumb drive.
Affected Part | Hercules HC 1.5 | Part Number 6060-1000-00 |
Replacement Part | Hercules HC 1.6 | Part Number 6060-1010-00 |
Please contact Braun Industries to arrange replacement of the affected Hercules HC 1.5 I/O Node(s) in your vehicle(s). The Braun Service contact information is as follows:
Phone: 877-344-9990 6:00 a.m. – 4:30 p.m. EDT,
Email: braunservice@braunambulances.com
It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by the notification under a sale or lease until the defect or noncompliance is remedied.
If Braun Industries is unable to arrange service as described above without charge within a 60 day period upon contacting Braun Industries, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, S.E., Washington, DC 20590 or call toll-free Auto Safety Hotline at 1-888327-4236 (TTY 1-800-424-9153); or go to http://www.safercar.gov.
Any lessor who receives a notification of a determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send a copy of such notice to the lessee of a leased motor vehicle, by first-class mail to the most recent lessee known to the lessor. Such notification shall be mailed within ten days of the lessor’s receipt of the notification from the vehicle manufacturer. This requirement applies to both initial and follow-up notifications but does not apply where the manufacturer has notified a lessor’s lessees directly.
We apologize in advance for the inconvenience this issue may cause your organization. We will continue to work with Weldon and make every effort to make this as simple as possible on both our Dealers and our Customers.
Sincerely,
Kim Braun
President – U.S. Division
Chronology :
Weldon, the manufacturer of the defective component, verbally notified Braun Industries of the upcoming recall on 5/9/22. Braun received recall notices from Wheldon for the 22E-037 recall on 5/17/22, decision for Braun recall on 5/20/22. Claims were received between 7/6/22 and 7/25/22. All 4 units covered under the recall were completed by 8/2/22.
22E037 – V‐MUX Hercules Hi Content Node HC1.5 – Weldon Akron Brass
22E037 – TSB 22-001 – V‐MUX Hercules Hi Content Node HC1.5 – Weldon Akron Brass
3 Affected Products
Vehicles
MAKE | MODEL | YEAR |
BRAUN AMBULANCES | EXPRESS PLUS TYPE I | 2020 |
BRAUN | CHIEF XL TYPE I | 2021 |
BRAUN | TLC | 2020 |
9 Associated Documents
Recall Acknowledgement
RCAK-22V370-2420.pdf 646.513KB
Defect Notice 573 Report
RCLRPT-22V370-8026.PDF 214.866KB
Recall 573 Report- 06/30/2022
RCLRPT-22V370-5524.PDF 214.87KB
Recall 573 Report- 06/30/2022
RCLRPT-22V370-7808.PDF 214.87KB
Recall Quarterly Report #1, 2022-2
RCLQRT-22V370-3717.PDF 211.113KB
Recall 573 Report- 09/06/2022
RCLRPT-22V370-6521.PDF 243.381KB
Recall Quarterly Report #2, 2022-3
RCLQRT-22V370-2788.PDF 211.208KB
Recall Quarterly Report #3, 2022-4
RCLQRT-22V370-0028.PDF 211.287KB
Issued Owner Notification Letter(Part 577)
RCONL-22V370-1734.pdf 215.738KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V370&docType=RCL
- 🍇➤Please Note: 1. The HD OBD option is available for heavy truck owners and the OBD/EOBD option is available for other vehicle. 2. Owners need to fix the problem with the truck first before they need clear the error code.
- 🍉➤【Support Full Systems for Heavy Duty Truck】 NL102 PLUS supports read and clear DTC, live data, ECU information for truck all systems. Including Engine, Transmission, Drivetrain, Suspension, ABS, ESP, Cluster, E-xhaust, P-articular, Suspension, Braking System, Cab Climate, Body Control, Instrument Panel, Fuel System and more, which are in compliance with J1939, J1708 and J1587 protocols, It includes almost American HD trucks(Class4-Class8), it is recommended that customers confirm before purchase that if they comply with the years and agreements supported by NL102P before purchasing.
- 🍋➤【Professional DPF Regeneration Tool】Force DPF Regen work on Cummings, Detroit, Maxxforce, ISUZU, HINO engine,It covers almost all US trucks, supported advanced features: DPF Regeneration,D-O-C Cleaning Procedures, DPF Regeneration in Parking, DPF Regeneration in Driving, DPF Onboard. NL102P's tool helps you re-awaken the engine power When the diesel p-articulates of the engine accumulate. It will save $800-$2500 for truck owners a year.
- 🍊➤【Excellent Oil Light Reset】NL102 PLUS support Oil service reset work on Cummings, Detroit, Maxxforce engine. when the replacement of engine oil is done, the truck system calculates when to change the engine oil and filter based on vehicle use. An oil change is required whenever indicated by the display, otherwise it will affect the engine maintenance and life. The NL102P truck scanner offers help to reset the Oil Life Reminder (Determine the Oil Service Light), ensure your driving safety.
- 🍐➤【All OBD/EOBD Diagnosis】NL102 PLUS supports both all 12V and all 24V truck, and it comes with 6 pin, 9 pin and 16 pin adapters for different interfaces. NL102 PLUS can read and earse the trouble codes, determine the MIL (check your Truck engine) and I/M Readiness, Freeze Frame, Live Data, O-xygen Sensor Test, On-Board Monitor, Vehicle Identification Info. Built in a DTC lookup library you can find the related code definition to help you determine if your car needs repair. In order to ensure that you can use the NL102P, please check the manual before purchasing.
- 🔥2024 TOP INTELLIGENT DIAGNOSTIC SCANNER FOR SEMI COMMERCIAL: ANCEL V5 HD obd2 scanner is specifically designed for 12V & 24V semi trucks,pickup trucks,heavy-duty trucks and 99% of commercial vehicles.you will enjoy✅All System Diagnostic;✅40+ Special Functions;✅ Full Bi-directional Test; ✅Advanced ECU Coding;✅Exclusive Remote Diagnosis Assistance;✅Full System Diagnostic ;✅Wider Vehicle Coverage;✅ Full HD OBD /OBDII /EOBD Modes;✅Top-level Hardware;✅>2 Yrs Free Update,Lifetime Tech Support
- 🚚40+ Resets with ABS SRS DPF Regen: ANCEL V5 HD includes 40+ resets for various systems, including ABS, SRS, DPF, EPB, BMS,DPF Regen, Injector Coding,Parameter Setting,Idle Speed Adjustment, Speed Limit Adjustment and more to fully meet your various needs. These resets can help reset the vehicle's systems to their default settings, eliminating any error codes or malfunctions that may be causing problems.Please send your VIN# to our 💌 amazon@anceltech.com 💌 to check compatibility.
- 🚛FULL BI-DIRECTIONAL CONTROL, GET YOU TO MALFUNCTIONS DIRECTLY:ANCEL V5 HD bidirectional scan tool supports bidirectional testing, which means it can both read and erase fault codes from the vehicle's ECUs.This feature saves time and money by eliminating the need for multiple scanners or tools.you can quickly identify whether the repair job works or not:Aftertreatment Test, Injector Test,Fuel Pump Test,Cylinder Test,Enigne State Monitor,A/C Compressor Test,Heated Oxygen Sensor Test and more.
- 🚜ADVANCED ECU CODING & PROGRAMMING:ANCEL V5 HD diesel truck scan tool comes with a powerful ECU programming and coding function, allowing you to reprogramme and decode the electronic control units (ECUs) of the vehicle.This feature is especially useful for technicians who need to update software,adjust parameters,or perform other modifications to the vehicle's electronic systems.🚦Note: ECU Coding is not universal to all cars, please check compatibility with VIN before order.
- 🚌OE-Level Full System Diagnostic:ANCEL V5 HD code reader is a professional-grade truck scanner that covers almost all the systems in semi-commercial vehicles, including engine, transmission, ABS, SRS, airbag,instrument panel, etc.It provides accurate and comprehensive diagnostic results,helping you quickly identify and solve vehicle problems,which are in compliance with J1939, 1708,ISO14230,ISO15765,ISO9141,ISO11898,E-J1850 VPW,SAE-J1850 PWM,J1587,CAN TP16,CAN TP20,AN-FD,and DOIP protocols.
- 🔥🔥🔥2024 New Functions Making X7 HD the Top Dog - Big Surprise!!! ANCEL X7 HD heavy duty truck scan tool 10 major functional advantages .✅>Full HDOBD/OBD2 Function ✅>ALL System Diagnostic ✅>40+ Reset Function ✅>Active Test / Bi-Directional Control✅>ECU Coding✅>Graphing Live Data✅>Wide Compatibility ✅>2 Yrs Free Update✅>Remote Operation✅>Bluetooth 5.0 & Wifi In addition, 8 major hardware advantages: ✅>6000 mAh✅>10.1 inch Tablet✅>2G RAM✅>32G ROM (Expandable to 128GB)✅>Data Record & Replay & Print✅>Android 10.0✅>Bluetooth 5.0 & Wifi✅>14 Languages
- 🚛Advanced ECU Coding & Programming - ANCEL X7 HD 10.1inch diesel truck scan tool is equipped with advanced ECU coding, supports Level calibration, Idle speed learning and Adjustment, Camshaft timing control learning, Control unit adaptations, Injector Codes, Read/Write VIN, Road speed limit optional vehicle speed set, etc... PLEASE NOTE that ECU codes are not compatible with all vehicles, please send us your VIN# to check vehicle compatibility.
- 🚛40+ Reset Functions & Bidirectional Control - 2024 newest top truck scanner diagnostic tool, comes with 40+ special services (ECU, Oil Reset, Injector Coding, EPB, ABS, SRS, Suspension, Throttle, etc. and always keep growing), which meet all your various needs for service and maintenance. Please send your VIN# to our 💌 amazon@anceltech.com 💌 to check compatibility.
- 🚛10 Inch All Systems Diesel Scanner & Full HDOBD/OBD2 Modes - ANCEL X7 HD diesel scanner diagnostic tool supports all systems scan, such as Engine, Brake, Retarder, TECU Transmission, Tachograph, ABS, SRS, TPMS, EPB, SAS, ESP, and other vehicle systems, comes with 10 obd2 service modes: read/erase error codes, Data Stream, I/M Readiness, Vehicle Information, Actuations, DTC Lookup, EVAP, view freeze frame, etc.
- 🚛OEM DPF Forced Regen & Cylinder Cutout Test & more - ANCEL X7 HD truck scanner not only supports DPF regeneration, DPF reset, DPF related information reset, DPR state reset, DPD forced regeneration etc, which helps you better solve the exhaust aftertreatment system problems, but also supports activate motor to do exhaust air in ABS Automatically. Moreover, it features TPMS activation, cylinder cut-off and learning functions.
- 🔎【Comprehensive Full Systems Diagnostic Tool For Truck】Launch Heavy Duty Truck Diagnostic Tool offers OE-Level diagnosis for all systems of heavy truck/Pickups/Bus/Van in compliance with OBD-II Communication Modes 1-10 and J1587, J1708 and J1939 protocols,Including Engine, Transmission, Drivetrain, Suspension, ABS, ESP, Cluster, E-xhaust, P-articular, Suspension, Braking System, Cab Climate, Body Control, Instrument Panel, Fuel System and more.
- 🔥【All OBD/EOBD Diagnosis】This truck scanner diagnostic tool supports both most 12V and 24V truck, and it comes with 6 pin, 9 pin and 16 pin adapters for different interfaces. Our truck scan tool can read codes, erase codes, I/M Readiness, Live data, EVAP Test. . . etc for obd2/eobd cars. Built in a DTC lookup library you can find the related code definition to help you determine if your car needs repair.
- 🚚【Wide Truck Applications】Heavy duty truck scan tool covers almost J1587, J1708 and J1939 protocols heavy duty trucks and OBD II vehicles. Such as Cummins, Paccar, Detroit, Perkins, International, Peterbilt, Allison, Eaton, Ford duty trucks and so on, Covers class 4 (14,001 lbs) through class 8 (33,000 lbs and over) heavy duty trucks. One that meets all the requirements! NOTE:Compatibility will vary on vehicles model and year, please send V-IN to check the compatibility before purchase.
- 💡【Friendly Design, Easy of Use】This heavy duty diagnostic scan tool is plug and play, simple and convenient, The excellent 2.8 inch LCD color screen makes it easy to view the displayed results and gives you a better overview of your car's problem areas and the identified codes. In addition, the processor is super-fast and responds without lagging, providing maximum comfort and efficiency in diagnostic and service work.
- ✨【3 YEARS WARRANTY & FREE LIFETIME UPDATES】The diesel truck scanner is exclusively designed for US truck. it's come With a full service functions and full systems and provides 24/7 technical support, 3 years warranty, 90-days free return for refund or replacement. This diesel scan tool is suitable for auto repair shops and technicians.No subscription fee and free lifetime updates.
- Powerful and Cost-Effective - An essential heavy duty truck scanner designed for heavy duty truck owner-operators and small commercial fleets. With the Diesel Decoder, just plug the diesel scan tool into the diagnostic port and pair with the free smartphone app to access in-depth HD diagnostic information.
- Swift and Adaptable - This heavy duty truck scanner recognizes both diagnostic trouble codes (DTCs) and brand-specific error codes for prevalent heavy-duty truck brands in North America, such as Freightliner, Peterbilt, Mack, Kenworth, Volvo, Western Star, among others and give the ability to perform DPF regens on select model years of Cummins, International, Detroit, Isuzu, Paccar, Mercedes, Hino and Mack/Volvo.
- Instant Repair Help - The diesel scan tool seamlessly connects to the Diesel Laptops comprehensive Diesel Repair Platform library so you can immediately start diagnosing and repairing any problems and get back on the road as soon as possible.
- Continuous Enhancement - Benefit from direct feature additions and updates via the app, our heavy duty truck scanner will continue to have functionality added over time. This removes the hassle of lengthy update processes and the financial strain of renewing costly diagnostic gear.
- 🌟【Run Your DPF Cleaner, Longer -Renew, Don't Replace!】Safeguard your truck from breakdowns and and high repair costs with focused DPF care. Opt for HD3400, featuring DPF regen, reset, DPR state control, and more, tailored for engines like Cummins, Detroit, Caterpillar, etc. Imagine this: easy and cost-effective DPF regen saving you from potential $10,000 to $30,000 in repairs. Unlock compliance-free operation for improved fuel efficiency, extended engine life, and significant cost savings
- 🚜【Maximize Caterpillar Engine Trucks' Potential!】HD3400 Plus diesel scanner, exclusively for Caterpillar engines (C7, C9, C11, C13, C15, C32, and more) commonly found in trucks like Caterpillar, Ford Pick-up, Freightliner, Peterbilt, Kenworth. Features include code reading/clearing, live data streaming, ECU retrieval, DPF regeneration and more. Unleash your Caterpillar engine's power!
- 🚛【Designed for Detroit Engine Trucks】ANCEL HD3400 heavy duty truck scan tool is compatible with a wide range of heavy duty commercial trucks – class 7 and class 8, medium duty trucks, light duty trucks and semi-trucks equipped with Detroit engines, including DD13, DD15, DD16, Series 50, Series 60, MBE 900, MBE 4000, OM501, OM502, DDDL 6, and DDDL 7.
- 🚐【Designed for Paccar Engine Trucks】ANCEL HD3400 heavy-duty truck scanner diagnostic tool is specifically designed for Paccar engines, including Paccar PX-7, PX-9, MX-11, MX-13. ❗Note: PACCAR engines post-2016 require a CAN-3 adapter for forced DPF regeneration. If you want to perform DPF regen for your PACCAR engines manufactured after 2016, please find us to get the additional CAN-3 adapter.
- 🌟【Unlock Advanced DPF Regeneration】Our diesel scanner diagnostic tool excels in DPF reset, providing active/forced regeneration and advanced DPF state control. Save time and money on DPF maintenance, making it the top choice for truck diagnostics. Elevate your DPF maintenance with our advanced features!
- 【Extensive Compatibility】After the upgrade, the compatibility is wider and more accurate! HD601 PRO heavy duty truck scanner supports all major truck models that comply with standard protocols (SAE J1939, SAE J1708, ISO 14230-4, ISO 15764-4 and ISO 9141-2, ISO 27145-4 and Euro6). Such as Cummins, Paccar, Detroit, Perkins, Freightliner, International, Peterbilt, Ford, Class 4-Class 8 trucks, etc. It also check engine diagnosis on most cars, minivans and light trucks from 1996 and latest.
- 【OE-Level Full System Diagnostic】HD601 PRO Diesel Scanner supports all system scans of heavy trucks compliant with standard protocols SAE J1939 & J1708, such as Engine, ABS, Transmission, Braking System, ESP, EPS, Fuel System, etc, It is a great scan tool for Cummins, Caterpillar, Detroit, Perkins, Maxxforce, BendixWabash, Wabaco, Haldex, Allison, Eaton heavy trucks, With this truck tool, you can get deep analysis data about the system and do some repairs by yourself, saving much time and money.
- 【Enhanced Diesel OBD Scanner】As a 2-in-1 code reader, it supports the latest ISO27145 and Euro6 protocols and enables diagnosis of car and truck engines. In addition to reading codes, clearing codes and displaying live data in a text or graphic format for trucks, you can also retrieve vehicle information, view freeze frames and look up DTCs. To ensure that this device works with different engines, it is also equipped with 6, 9 and 16 pin cables that allow you to easily turn off the CEL light.
- 【DTC Library】+【Life Time Free Update】The built-in DTC library allows you to retrieve the codes directly without searching for the definition in the book. Whether you are a professional mechanic or a DIY car owner, HD601 diesel scanner explains the existing problem, makes it easier for you to understand the codes definition and fix the problem faster. Plus, you get a lifetime free internet updates, so you always have the latest software for diagnostics in English and Spanish languages.
- 【Friendly Design, Easy of Use】This scanner is plug and play, simple and convenient, and very friendly for beginners. With improved buttons for easy menu navigation. The excellent 2.8 inch LCD color screen makes it easy to view the displayed results and gives you a better overview of your car's problem areas and the identified codes. In addition, the processor is super-fast and responds without lagging, providing maximum comfort and efficiency in diagnostic and service work.
- 【2024 NEWEST LAUNCH 1st Advanced Scan Tool Compatible With 12V&24V Vehicles】Design for Passenger&Commercial Vehicles 2 in1,work for Cars/Trucks/buses/trailers/excavators/diesel engine/pick-up/etc.
- 【J2534 Reprogramming with Smartlink C】Advanced OEM J2534 reprogramming,Helps access direct data online, replace existing software/firmware in ECU,program new ECUs and fix software-controlled issue.
- 【Over 60 Service Reset Functions + Bi-Directional + ECU Coding 】This scan tool can support ECU Coding,60+ reset service functions like SAS/EPB/TPMS/DPF/Oil/Brake/ABS Bleed, Injector coding, etc.
- 【2024 BEST Advanced Hardware & All Systems Diagnosis+Topology Display 】Support All systems Diagnostic including ENG, AT, ECM, TCM, ABS, SRS, BCM, BMS, TPMS, SAS, Fuel System, Light System and more.
- 【Wider Vehicle Coverage of 12V & 24V Vehicles + 24 Languages】LAUNCH X431 PRO3S+SMARTLINK HD automotive scanner is ALL-IN-ONE Scan Tool for 12V cars and 24V Heavy-duty trucks support CANFD & DOIP.
- 【Full Systems Heavy Duty Scanner Tool】:this heavy duty scanner tool supports Read DTC and Clear DTC, Live Data,Engine Check, Transmission, Drivetrain, Suspension, Cluster, Suspension, Braking System, Cab Climate, Body Control, Instrument Panel, Fuel System and more, which are in compliance with J1939, J1708 and J1587 protocols,
- 【OBD2/HDOBD/EOBD All Diagnosis】: supports both all 12V and all 24V truck, with 6 pin and 9 pin adapters for different interfaces.It support reading code, earsing trouble codes, Live Data, determine the MIL (check your Truck engine) and I/M Readiness, Freeze Frame, O2 Sensor Test, On-board Monitor, Vehicle Identification Info.It can lookup DTC, translates the related code's meaning to help you know what's wrong with the car.
- 【Suitable for Most Trucks】:diesel diagnostic scanner support all truck standard protocols SAEJ1939/ J1587/ J1708,it work on heavy duty trucks/ light truck/ mini vans/ buses/ pickups from1996 to now.
- 【CANBUS System】:Detect the CANBUS node, and easily find out the wrong modoles and lines.
- 【Professional Automotive Scanner Diagnostic Tools】:Designed specifically for HDOBD/OBD2/EOBD.This HD10 covers all the functions of HDOBD,OBD2,and EOBD. What is more important is that it provide the results correctly and quickly, and you can read the results with graghs, which make you easier to read.
- 👍【2024 Newest wide Coverage for Heavy truck】: With support for standard HD OBD protocols and customized protocols, ANCEL HD3400 PRO provides 98% coverage for heavy truck models in the US market, including those with Cummins, Detroit, Caterpillar, Paccar engines,and trucks like Ford, Autocar, western star, Freightliner, Kenworth, Peterbilt, caterpillar,Terex, Thomas, Sany, Komatsu, Agrifac , Isuzu, Fuso, Hino,Volvo and more.
- 🚛【Available for Cummins 】ANCEL HD3400 Pro is specifically designed to support a wide range of Cummins engines found in trucks like Ford, Volvo, Freightliner, Kenworth, and more, as well as Sany machinery, Agrifac vehicles, RVs, and more. Compatible with ISX, ISM, ISN, QSB, X12, ISB, ISC, ISD, ISG, ISK, ISL, X15, B6.7, L9, L9N, QSM11, and other popular models.
- 🚒【Available for Caterpillar】exclusively designed for Caterpillar engines (C7, C9, C11, C13, C15, C32, and more), you can perform top-notch diagnostics to keep your trucks running reliably. Compatible with popular truck models like Kenworth, Peterbilt, Freightliner, International, Mack, and Volvo.
- 🚛【Available for Paccar&Detroit】ANCEL HD3400 PRO is compatible with a wide range of engine types, including Detroit engines (Series 50, Series 55, Series 60, OM501, OM502, DD5, DD13, DD15, DD16,MBE 900, MBE 4000, DD8, DDDL 6, DDDL 7, CPC2, CPC02T, CPC04T, CPC302T and More) and Paccar engines(PX-7, PX-9, MX-11, MX-13 and more). like medium-duty or light-duty trucks, or even semi-trucks
- 🚒【Superb Lifetime Free Update,Best Bang For The Buck】ANCEL HD3400 PRO diesel code reader allow our customers get the latest version with free update via WIFI,With Lifetime Free Update,HD3400 PRO is way more valuable by comparing with the other OBD diagnosis,which can save hundreds of dollar for our customers!
Last update on 2024-04-11 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
IMPORTANT SAFETY RECALL This notice applies to your vehicle, 3C7WRNCL9NG186467 Braun Recall Notice: 22V370 This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Braun Industries has decided a safety related defect may exist with some Weldon Hercules HC 1.5 I/O Nodes, Weldon Part Number 6060-1000-00, produced between April 21, 2022, and April 29, 2022. In the affected products, Weldon installed a termination resistor on the circuit board. In this configuration and when combined with external resistors located in a harness or with multiple nodes that do not have external resistors, CAN communication may become compromised which can impact any of the electrical loads that are connected to the CAN, including vehicle lighting, potentially increasing the risk of a crash. Since V-MUX systems are configured to match user needs, some installations may not present an issue at initial acceptance test, but nevertheless should be remedied. You are receiving this notice because Braun records indicate you have received shipments of affected units. Braun will remedy the affected units free of charge by replacing them with Hercules HC 1.6 that has the same functionality as the Hercules 1.5 but does not include the internal terminator resistor. Replacement Hercules HC 1.6 I/O Nodes are available as of May 15th, 2022. Replacement is done by removing the affected Hercules HC 1.5 I/O Nodes and installing Hercules HC 1.6 I/O Nodes. Replacement labor for each node replacement is 15 minutes per node. Nodes will require OEM programming which can be done by USB thumb drive. Affected Part Replacement Part Hercules HC 1.5 Hercules HC 1.6 Part Number 6060-1000-00 Part Number 6060-1010-00 Please contact Braun Industries to arrange replacement of the affected Hercules HC 1.5 I/O Node(s) in your vehicle(s). The Braun Service contact information is as follows: Phone: 877-344-9990 6:00 a.m. – 4:30 p.m. EDT, Email: braunservice@braunambulances.com It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by the notification under a sale or lease until the defect or noncompliance is remedied. If Braun Industries is unable to arrange service as described above without charge within a 60 day period upon contacting Braun Industries, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, S.E., Washington, DC 20590 or call toll-free Auto Safety Hotline at 1-888- 327-4236 (TTY 1-800-424-9153); or go to http://www.safercar.gov. Any lessor who receives a notification of a determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send a copy of such notice to the lessee of a leased motor vehicle, by first-class mail to the most recent lessee known to the lessor. Such notification shall be mailed within ten days of the lessor’s receipt of the notification from the vehicle manufacturer. This requirement applies to both initial and follow-up notifications but does not apply where the manufacturer has notified a lessor’s lessees directly. We apologize in advance for the inconvenience this issue may cause your organization. We will continue to work with Weldon and make every effort to make this as simple as possible on both our Dealers and our Customers. Sincerely, Kim Braun President – U.S. Division
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-370 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Braun Ambulances Submission Date : MAY 24, 2022 NHTSA Recall No. : 22V-370 Manufacturer Recall No. : NR Manufacturer Information : Manufacturer Name : Braun Ambulances Address : 1170 Production Drive Van Wert OH 45891 Company phone : 4192327020 Population : Number of potentially involved : 4 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2020-2020 Braun Ambulances Express Plus Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only two Braun Ambulances MY2020 Express Plus on a Ford MY2022 F450 chassis with a diesel engine. Production Dates : APR 21, 2022 – APR 21, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 2 : 2020-2020 Braun Ambulances TLC Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only one Braun Ambulances MY2020 TLC on a Navistar MY2022 MV607 chassis with a diesel engine. Production Dates : APR 29, 2022 – APR 29, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-370 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2021-2021 Braun Ambulances Chief XL Type I Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only one Braun Ambulances MY2021 Chief XL Type I on a Dodge MY2022 R5500 chassis with a diesel engine. Production Dates : APR 22, 2022 – APR 22, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : In the affected products, the Node contains a termination resistor installed on the node circuit board instead of the termination resistor being installed only within the electrical harness. If the vehicle network design has not accounted for this additional resistor, it may reduce the bus resistance below the defined tolerance levels and may lead to a loss of data on the CAN network. Installations with multiple nodes are more likely to experience the condition FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : If the bus resistence is reduced, the CAN network connection could faill which may interrupt the transfer of data on this connection. If the CAN network connection is interrupted or fails and depending on how the vehicle’s electrical systems are designed, it may impact the operation of various electrical loads controlled by the Node, including vehicle lighting, which may increase the risk of a crash Description of the Cause : Due to a bill of material error, a resistor installed on the printed circuit board was inadvertently included by the manufacturer Identification of Any Warning that can Occur : NR Involved Components : Component Name 1 : V-mux Hercules HC Node 1.5 Component Description : High-Content Node Component Part Number : Weldon P/N:6060-1000-00 (Braun P/N: 28735) Part 573 Safety Recall Report 22V-370 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : Weldon Division of Akron Brass Address : 3656 Paragon Drive Columbus Ohio 43228 Country : United States Chronology : Weldon, the manufacturer of the defective component, verbally notified Braun Industries of the upcoming recall on 5/9/22. Braun received recall notices from Wheldon for the 22E-037 recall on 5/17/22. Description of Remedy : Description of Remedy Program : Braun Industries will contact affected customers and their dealer in to inform them of the subject components. Braun Industries and/or their dealer will arrange for the affected Weldon Hercules HC 1.5 I/O nodes to be removed from the customer vehicle/s. Replacement nodes will be installed in the customers vehicle/s. Dealers who conduct the removal and replacement of the nodes will contact Braun Industries Service for reimbursement upon completion of work. How Remedy Component Differs from Recalled Component : The remedy component will have the additional termination resistor removed from the circuit board. Identify How/When Recall Condition was Corrected in Production : Vehicles with the affected node have had those nodes replaced starting on 5/11/22. Remedy of production vehicles at Braun’s location is still in process. Recall Schedule : Description of Recall Schedule : NR Planned Dealer Notification Date : MAY 25, 2022 – JUN 01, 2022 Planned Owner Notification Date : MAY 31, 2022 – JUN 07, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-370 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Braun Ambulances Submission Date : JUN 30, 2022 NHTSA Recall No. : 22V-370 Manufacturer Recall No. : NR Manufacturer Information : Manufacturer Name : Braun Ambulances Address : 1170 Production Drive Van Wert OH 45891 Company phone : 4192327020 Population : Number of potentially involved : 4 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2020-2020 Braun Ambulances TLC Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only one Braun Ambulances MY2020 TLC on a Navistar MY2022 MV607 chassis with a diesel engine. Production Dates : APR 29, 2022 – APR 29, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 2 : 2020-2020 Braun Ambulances Express Plus Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only two Braun Ambulances MY2020 Express Plus on a Ford MY2022 F450 chassis with a diesel engine. Production Dates : APR 21, 2022 – APR 21, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-370 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2021-2021 Braun Ambulances Chief XL Type I Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only one Braun Ambulances MY2021 Chief XL Type I on a Dodge MY2022 R5500 chassis with a diesel engine. Production Dates : APR 22, 2022 – APR 22, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : In the affected products, the Node contains a termination resistor installed on the node circuit board instead of the termination resistor being installed only within the electrical harness. If the vehicle network design has not accounted for this additional resistor, it may reduce the bus resistance below the defined tolerance levels and may lead to a loss of data on the CAN network. Installations with multiple nodes are more likely to experience the condition FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : If the bus resistence is reduced, the CAN network connection could faill which may interrupt the transfer of data on this connection. If the CAN network connection is interrupted or fails and depending on how the vehicle’s electrical systems are designed, it may impact the operation of various electrical loads controlled by the Node, including vehicle lighting, which may increase the risk of a crash Description of the Cause : Due to a bill of material error, a resistor installed on the printed circuit board was inadvertently included by the manufacturer Identification of Any Warning that can Occur : NR Involved Components : Component Name 1 : V-mux Hercules HC Node 1.5 Component Description : High-Content Node Component Part Number : Weldon P/N:6060-1000-00 (Braun P/N: 28735) Part 573 Safety Recall Report 22V-370 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : Weldon Division of Akron Brass Address : 3656 Paragon Drive Columbus Ohio 43228 Country : United States Chronology : Weldon, the manufacturer of the defective component, verbally notified Braun Industries of the upcoming recall on 5/9/22. Braun received recall notices from Wheldon for the 22E-037 recall on 5/17/22. Description of Remedy : Description of Remedy Program : Braun Industries will contact affected customers and their dealer in to inform them of the subject components. Braun Industries and/or their dealer will arrange for the affected Weldon Hercules HC 1.5 I/O nodes to be removed from the customer vehicle/s. Replacement nodes will be installed in the customers vehicle/s. Dealers who conduct the removal and replacement of the nodes will contact Braun Industries Service for reimbursement upon completion of work. How Remedy Component Differs from Recalled Component : The remedy component will have the additional termination resistor removed from the circuit board. Identify How/When Recall Condition was Corrected in Production : Vehicles with the affected node have had those nodes replaced starting on 5/11/22. Remedy of production vehicles at Braun’s location is still in process. Recall Schedule : Description of Recall Schedule : NR Planned Dealer Notification Date : MAY 25, 2022 – JUN 01, 2022 Planned Owner Notification Date : MAY 31, 2022 – JUN 24, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-370 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Braun Ambulances Submission Date : SEP 06, 2022 NHTSA Recall No. : 22V-370 Manufacturer Recall No. : NR Manufacturer Information : Manufacturer Name : Braun Ambulances Address : 1170 Production Drive Van Wert OH 45891 Company phone : 4192327020 Population : Number of potentially involved : 4 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2020-2020 Braun Ambulances TLC Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only one Braun Ambulances MY2020 TLC on a Navistar MY2022 MV607 chassis with a diesel engine. Production Dates : APR 29, 2022 – APR 29, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 2 : 2020-2020 Braun Ambulances Express Plus Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only two Braun Ambulances MY2020 Express Plus on a Ford MY2022 F450 chassis with a diesel engine. Production Dates : APR 21, 2022 – APR 21, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-370 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2021-2021 Braun Ambulances Chief XL Type I Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only one Braun Ambulances MY2021 Chief XL Type I on a Dodge MY2022 R5500 chassis with a diesel engine. Production Dates : APR 22, 2022 – APR 22, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : In the affected products, the Node contains a termination resistor installed on the node circuit board instead of the termination resistor being installed only within the electrical harness. If the vehicle network design has not accounted for this additional resistor, it may reduce the bus resistance below the defined tolerance levels and may lead to a loss of data on the CAN network. Installations with multiple nodes are more likely to experience the condition FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : If the bus resistence is reduced, the CAN network connection could faill which may interrupt the transfer of data on this connection. If the CAN network connection is interrupted or fails and depending on how the vehicle’s electrical systems are designed, it may impact the operation of various electrical loads controlled by the Node, including vehicle lighting, which may increase the risk of a crash Description of the Cause : Due to a bill of material error, a resistor installed on the printed circuit board was inadvertently included by the manufacturer Identification of Any Warning that can Occur : NR Involved Components : Component Name 1 : V-mux Hercules HC Node 1.5 Component Description : High-Content Node Component Part Number : Weldon P/N:6060-1000-00 (Braun P/N: 28735) Part 573 Safety Recall Report 22V-370 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : Weldon Division of Akron Brass Address : 3656 Paragon Drive Columbus Ohio 43228 Country : United States Chronology : Weldon, the manufacturer of the defective component, verbally notified Braun Industries of the upcoming recall on 5/9/22. Braun received recall notices from Wheldon for the 22E-037 recall on 5/17/22, decision for Braun recall on 5/20/22. Claims were received between 7/6/22 and 7/25/22. All 4 units covered under the recall were completed by 8/2/22. Description of Remedy : Description of Remedy Program : Braun Industries will contact affected customers and their dealer in to inform them of the subject components. Braun Industries and/or their dealer will arrange for the affected Weldon Hercules HC 1.5 I/O nodes to be removed from the customer vehicle/s. Replacement nodes will be installed in the customers vehicle/s. Dealers who conduct the removal and replacement of the nodes will contact Braun Industries Service for reimbursement upon completion of work. How Remedy Component Differs from Recalled Component : The remedy component will have the additional termination resistor removed from the circuit board. Identify How/When Recall Condition was Corrected in Production : Vehicles with the affected node have had those nodes replaced starting on 5/11/22. Remedy of production vehicles at Braun’s location is still in process. Recall Schedule : Description of Recall Schedule : Recall Dealer Notifications will be sent between 5/25/22 and 6/1/22. Owner Notification Letters will be mailed first class between 5/31/22 and 6/24/22. Planned Dealer Notification Date : MAY 25, 2022 – JUN 01, 2022 Planned Owner Notification Date : MAY 31, 2022 – JUN 24, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-370 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Braun Ambulances Submission Date : JUN 30, 2022 NHTSA Recall No. : 22V-370 Manufacturer Recall No. : NR Manufacturer Information : Manufacturer Name : Braun Ambulances Address : 1170 Production Drive Van Wert OH 45891 Company phone : 4192327020 Population : Number of potentially involved : 4 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2020-2020 Braun Ambulances TLC Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only one Braun Ambulances MY2020 TLC on a Navistar MY2022 MV607 chassis with a diesel engine. Production Dates : APR 29, 2022 – APR 29, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 2 : 2020-2020 Braun Ambulances Express Plus Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only two Braun Ambulances MY2020 Express Plus on a Ford MY2022 F450 chassis with a diesel engine. Production Dates : APR 21, 2022 – APR 21, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-370 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2021-2021 Braun Ambulances Chief XL Type I Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : DIESEL Descriptive Information : Recall population is determined by the vehicles that have the affected Hercules HC 1.5 I/O nodes per the supplied serial numbers from Weldon. Vehicles not affected by this recall do not contain the internal terminator resistor. Only one Braun Ambulances MY2021 Chief XL Type I on a Dodge MY2022 R5500 chassis with a diesel engine. Production Dates : APR 22, 2022 – APR 22, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : In the affected products, the Node contains a termination resistor installed on the node circuit board instead of the termination resistor being installed only within the electrical harness. If the vehicle network design has not accounted for this additional resistor, it may reduce the bus resistance below the defined tolerance levels and may lead to a loss of data on the CAN network. Installations with multiple nodes are more likely to experience the condition FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : If the bus resistence is reduced, the CAN network connection could faill which may interrupt the transfer of data on this connection. If the CAN network connection is interrupted or fails and depending on how the vehicle’s electrical systems are designed, it may impact the operation of various electrical loads controlled by the Node, including vehicle lighting, which may increase the risk of a crash Description of the Cause : Due to a bill of material error, a resistor installed on the printed circuit board was inadvertently included by the manufacturer Identification of Any Warning that can Occur : NR Involved Components : Component Name 1 : V-mux Hercules HC Node 1.5 Component Description : High-Content Node Component Part Number : Weldon P/N:6060-1000-00 (Braun P/N: 28735) Part 573 Safety Recall Report 22V-370 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : Weldon Division of Akron Brass Address : 3656 Paragon Drive Columbus Ohio 43228 Country : United States Chronology : Weldon, the manufacturer of the defective component, verbally notified Braun Industries of the upcoming recall on 5/9/22. Braun received recall notices from Wheldon for the 22E-037 recall on 5/17/22. Description of Remedy : Description of Remedy Program : Braun Industries will contact affected customers and their dealer in to inform them of the subject components. Braun Industries and/or their dealer will arrange for the affected Weldon Hercules HC 1.5 I/O nodes to be removed from the customer vehicle/s. Replacement nodes will be installed in the customers vehicle/s. Dealers who conduct the removal and replacement of the nodes will contact Braun Industries Service for reimbursement upon completion of work. How Remedy Component Differs from Recalled Component : The remedy component will have the additional termination resistor removed from the circuit board. Identify How/When Recall Condition was Corrected in Production : Vehicles with the affected node have had those nodes replaced starting on 5/11/22. Remedy of production vehicles at Braun’s location is still in process. Recall Schedule : Description of Recall Schedule : NR Planned Dealer Notification Date : MAY 25, 2022 – JUN 01, 2022 Planned Owner Notification Date : MAY 31, 2022 – JUN 24, 2022 * NR – Not Reported
SEOCONTENT-END