“This site contains affiliate links for which OEMDTC may be compensated” |
July 3, 2020 NHTSA CAMPAIGN NUMBER: 20V394000
Engine Compartment Flap Hinge Improperly Welded
If the engine compartment flap detaches from the coach while it is in motion, it can become a projectile, increasing the risk of a crash.
NHTSA Campaign Number: 20V394
Manufacturer Daimler Coaches North America
Components STRUCTURE
Potential Number of Units Affected 55
Summary
Daimler Coaches North America (DCNA) is recalling certain 2018-2019 Setra S407 and 2019-2020 S417 passenger coaches. The engine compartment flap may not have sufficient welding seams on the hinges, allowing the hinge connection to fail and the engine compartment flap to detach from the coach.
Remedy
DCNA will notify owners, and dealers will inspect the engine compartment flap seam welds and, if necessary, re-weld or replace the engine compartment flap, free of charge. The recall began August 28, 2020. Owners may contact DCNA customer service at 1-905-403-7807. DCNA’s number for this recall is 75.00U20104A.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
COMPLAINT
The weld seams on the brackets of the engine compartment flap were not executed fully.
CAUSE
Error in the documentation.
REMEDY
Check the weld seams on the brackets of the engine compartment flap against the latest documentation and, if necessary, incorporate the missing weld seams.
If the weld seams cannot be incorporated, the engine compartment flap must be replaced with a new one.
MEASURE TYPE
The scope of the work is carried out as part of a safety recall (RC).
REPLACEMENT PARTS REQUIRED
Quantity | Designation | Number | Comment |
1 | Engine compartment flap | A 629 750 40 33 | Only if required |
Procedure
Warning
Risk of injury. Danger due to the dropping of unwieldy or heavy components. The unforeseen dropping of components can result in serious injuries to the body and limbs.
Warning
Risk of accident. Danger when lifting and transporting heavy components. The use of defective or unsuitable lifting equipment and hoists for the lifting and transporting of heavy components could result in serious or fatal injuries to all persons involved if the component were to drop or slip.
Warning
Risk of entrapment and crushing. Danger to hands, arms and legs during all work on doors, flaps, covers and roof hatches.
Warning
Risk of injury. Danger from the spontaneous opening or dropping of flaps, doors, covers and panels. There is a risk of flaps, doors, covers or panels that have been closed or fitted incorrectly opening or coming loose spontaneously, especially while the vehicle is in motion, and thereby causing injury.
Warning
Risk of entrapment and crushing. Reaching in between mechanically operated parts may result in serious injuries due to the severing or crushing of body parts.
Warning
Risk of fatal injury. Risk of fatal injury due to high voltages present during electric arc welding. Risk of explosion when welding near highly flammable materials. Risk of injury from welding spatter and ultraviolet light during welding. Risk of poisoning from inhalation of welding fumes. Welding sparks and splashes of liquid weld matter could cause severe burns if they come into contact with unprotected parts of the body. The ultraviolet light emitted during electric arc welding may cause damage to the eyes and burn unprotected skin. If electric welding work is carried out in a damp environment or on a wet surface, there is a risk of fatal injury as the voltage may be discharged through the human body. This could cause severe burning, cardiac fibrillation or heart failure. Standard work clothes (made of cotton or synthetic fibres) may catch fire due to welding sparks and splashes of liquid weld metal, and inflict very severe burns as a result.
Caution
Irreparable damage due to overvoltage and risk of fire. Measures required for the prevention of damage to buses or components during electric welding work. In order to prevent damage, the following measures should be carried out before the commencement of welding work:
Warning
Risk of explosion and poisoning. Risk of explosion and of poisoning from solvent vapours and gases. There is a risk of injury to the eyes and skin when handling corrosion inhibitors. Do not spray corrosion inhibitor onto naked flames or red-hot materials. Keep corrosion inhibitor away from sources of ignition at all times. Carry out the work in well-ventilated rooms and wear respiratory protection.
Warning
Risk of accident. Danger from unauthorised starting of the engine or movement of the vehicle. Persons in areas of the bus that are hidden from view (underbody, rear, roof, etc.) are at risk of injury if the engine is started or the vehicle is moved by other or unauthorised persons.
Checking the weld seams
- Open the engine compartment flap.
- Check the weld seams on the brackets of the engine compartment flap against the latest documentation. Result 1 / 2
All weld seams present in accordance with the documentation.
▶ No further work necessary, close the engine compartment flap.
Result 2 / 2
Not all weld seams are present in accordance with the documentation.
▶ Remove the engine compartment flap and incorporate the missing weld seams in accordance with the documentation.
Completing the weld seams
- Abrade the weld area down to bright metal and clean.
Required material |
Pneumatic brush grinder Model: MBX® Metal Blaster® |
- Cover or mask off adjacent areas extensively and provide protection against flying sparks.
- Incorporate the missing weld seams to a professional standard.
Note
To ensure that the optimum welder setting is used, it is advisable to perform a test weld on a scrap sheet beforehand.
- Remove burn-off deposits and clean the welding point.
Required material |
Pneumatic brush grinder
Model: MBX® Metal Blaster® |
- Apply primer and corrosion inhibitor.
Note
Observe the application information and drying times of the paint manufacturer.
Fitting and adjusting the engine compartment flap
Note
Whenever you are adjusting flap gap dimensions, always take into consideration (adapt to) the gap dimensions of adjacent components.
Note
The following priorities govern the adjustment of exterior flaps: Priority 1: leak-tightness of the flaps. Priority 2: gap dimensions, appearance of the gap line and evenness of the outside of the flap surface in closed condition. Priority 3: gap dimensions, position and evenness of the outside of the flap surface in open condition.
- →
Reference values | |
Engine compartment flap gap dimension (D) | 6 … 10 mm |
Reference values | |
Uniform gap line from (1.1) to (1.2), permissible deviation | 1.5 |
Note
Adjust all gaps around the engine compartment flap in such a way that their dimensions are as equal as possible. The maximum relative deviation is 1.5 mm.
- →
Reference values | |
Transitions (planar alignment) (E) from the outer surface to all adjacent components | 0+1.5+1.5 mm |
SEOCONTENT-START
12.8.2020
1/6
Technical
information
TI No.: 75.00U20104A Distribution list: D Distribution date:
12.08.2020
Valid until: 31.12.2040
The point of contact is the EvoBus after-sales service in each country
Model: TC 400 USA
MODEL SERIES: 629540; 629557
TITLE: TC 400 USA – completing the weld seams on the brackets of the
engine compartment flap
OPERATION TEXTS
Operation no. Operation text Working time/h Comment
02-1920 Check weld seams on brackets of engine
compartment flap
0.2
02-1921 Remove and fit engine compartment flap
(after check)
1.2 Associated work for 02-1920
Operation no. Operation text Working time/h Comment
02-1922 Complete weld seams on brackets of engine
compartment flap (engine compartment flap
removed)
2.5 Associated work for 02-1921
The times apply for work at an hourly rate.
DEFECT NUMBER
Defect no.: Designation
7591065
CODEWORD
7500U20104
INTRODUCTION OF MODIFICATIONS INTO SERIES PRODUCTION
01.02.2020
WARRANTY AND GOODWILL SETTLEMENTS
Field measure type RC: 100 % of costs will be accepted.
BUS/MCC BUS/MCC-O
pp. pp.
Johannes Lehmann Markus Fischer
Attachments
*********************************************************************************************************
Daimler Coaches North America
2477 Deerfield Drive
Fort Mill, SC. 29715
August 28, 2020
A Yankee Line Inc
Attn: Donald Ogden
370 West First St
Boston MA 02127
IMPORTANT SAFETY RECALL
This notice applies to your vehicle
WKKA404 WKKA574 WKKA574 WKKA574
WKKA404 WKKA574 WKKA574 WKKA574
WKKA404 WKKA574 WKKA574 WKKA574
WKKA404 WKKA574 WKKA574 WKKA574
WKKA574 WKKA574 WKKA574 WKKA574
WKKA574 WKKA574
SUBJECT: SAFETY RECALL OF 2018~2020 SETRA S407 & S417TC COACHES
Ref.: NHTSA recall reference # 20V-394
Setra Bulletin # TI 75.00U20104A
Dear Setra Owner,
This notice is sent to you in accordance with the requirements of the U.S. National Traffic and Motor Vehicle
Safety Act.
EvoBus GmbH (the manufacturer of Setra coaches) has decided that a defect (details below) which relates to
motor vehicle safety exists in certain 2018~2019 Setra S407 and certain 2019~2020 Setra S417 vehicles.
EvoBus therefore has initiated a recall of these vehicles. Our records indicate that your vehicle is included in
this group.
Due to an error in manufacturing, the welding on the hinge mounting of the engine compartment flap could be
incomplete. This could reduce the overall strength and stability of the hinge possibly resulting in the engine
compartment flap becoming detached. A detached engine compartment flap could increase the risk of injury or
a crash.
Setra will remedy this by inspecting the welding seams on the hinge mountings of the engine compartment flap
and, if necessary, re-weld or replace the engine compartment flap. This repair will be performed free of charge.
Details are outlined in the repair procedure number TI 75.00U20104A. Please allow for up to three (3) hours to
schedule and complete the repair.
Please contact DCNA Customer Service Line at 1-800-206-9728 if you need further information.
Setra strongly urges you to perform the recall inspection work on your vehicle(s) as soon as possible.
Daimler Coaches North America
2477 Deerfield Drive
Fort Mill, SC. 29715
For reimbursement of the repair, please submit a completed Setra Warranty Claim Form or refer to TI bulletin
75.00U20104A for complete details;
US Mail Email
Daimler Coaches North America (DCNA) DCNAWarranty@daimler.com
Attn: Shelly Bontrager
238 Oak Street,
Millersburg, IN. 46543
After contacting Setra Customer Service, if you are still unable to have the safety defect remedied without
charge and within a reasonable time, you may submit a complaint to:
For US customers:
You may submit a written complaint to the Administrator, National Highway Traffic Safety Administration, 1200
New Jersey Avenue, SE, Washington, DC 20590, or call 888 327-4236 (TTY: 800-424-9153), or go to
https://www.safercar.gov if remedy difficulties exist.
If you are no longer the vehicle owner, or have had a change of address, please complete the reverse side of this
letter and return the complete letter in the enclosed envelope. If this is a leased vehicle and the lessor and
registered owner receive this notice, Federal law requires any lessor who receives a notification of a
determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send the
notice to the lessee within 10 days.
If you have paid to have this recall condition corrected prior to this notice you may be eligible to receive
reimbursement. Please see the reverse side of this notice for details.
Please contact your authorized Setra dealer should you have any questions or encounter any difficulty regarding
this recall. If your dealer is unable to remedy your situation, please contact us at our Setra Customer Service
Line at 1-800-206-9728 if you have any questions about this recall.
We apologize for any inconvenience this situation may cause you.
Sincerely
Daimler Coaches North America
Warranty Department
Daimler Coaches North America
2477 Deerfield Drive
Fort Mill, SC. 29715
IMPORTANT
IF FOR ANY REASON YOU DO NOT NOW OWN THIS VEHICLE OR HAVE A CHANGE OF ADDRESS, PLEASE COMPLETE THE SECTION BELOW,
PLACE IN THE ENCLOSED ENVELOPE, AND DROP IN ANY MAIL BOX. IF POSSIBLE, PROVIDE THE NAME AND ADDRESS OF THE PRESENT
OWNER SO THAT WE MAY CONTACT THEM.
SCRAPPED
STOLEN
OTHER
SOLD I HAVE SOLD THE VEHICLE TO:
MY NEW ADDRESS IS:
NAME
STREET APT.
CITY STATE ZIP
PHONE
THANK YOU FOR YOUR COOPERATION
**** PLEASE DO NOT DETACH. RETURN COMPLETE LETTER ****
DO NOT USE THE ENCLOSED ENVELOPE FOR OTHER CORRESPONDENCE
Reimbursement to Customers for Repairs Performed Prior to Recall
If you have already paid to have this recall condition corrected you may be eligible to receive reimbursement.
Requests for reimbursement may include parts, labor, fees and taxes. Reimbursement may be limited to the amount
the repair would have cost if completed by an authorized Setra dealer. The following documentation must be
presented to your dealer for reimbursement.
Original or clear copy of all receipts, invoices and/or repair orders that show:
The name and address of the person who paid for the repair.
The Vehicle Identification Number (VIN) of the vehicle that was repaired.
What problem occurred, what repair was done, when it was done and who repaired it.
The total cost of the repair expense that is being claimed.
Proof of payment of repair (copy of front and back of cancelled check, or copy of credit card receipt).
Reimbursement will be made by check from your dealer. If your claim is denied you will receive a letter from
Setra within 60 days of receipt with the reason(s) for the denial.
Please speak with your dealer concerning this matter.
SEOCONTENT-END
4 Affected Products
Vehicles
MAKE | MODEL | YEAR |
SETRA | S407 CC | 2018-2019 |
SETRA | S417 TC | 2019-2020 |
10 Associated Documents
Recall Acknowledgement
RCAK-20V394-6881.pdf 245.074KB
Defect Notice 573 Report
RCLRPT-20V394-5411.PDF 213.844KB
Defect Notice 573 Report
RCLRPT-20V394-8594.PDF 213.85KB
Recall Quarterly Report #3, 2021-1
RCLQRT-20V394-0290.PDF 211.326KB
Recall Quarterly Report #2, 2020-4
RCLQRT-20V394-7581.PDF 211.248KB
Owner Notification Letter(Part 577)
RCONL-20V394-6799.pdf 731.506KB
Remedy Instructions and TSB
RCRIT-20V394-7193.pdf 402.61KB
Recall Quarterly Report #1, 2020-3
RCLQRT-20V394-6480.PDF 211.145KB
Recall 573 Report- Amendment 1
RCLRPT-20V394-7613.PDF 216.888KB
Recall Quarterly Report #4, 2021-2
RCLQRT-20V394-8350.PDF 211.439KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V394&docType=RCL
- [MORE POWERFUL] Up to 135 Amp output allows you to weld mild steel up to 2/5” in the plate. Suitable for 2LB .030” & .035” flux core wire.
- [MULTI-PROCESS] 3-in-1 Welder, capable of Gasless MIG/Stick/Lift TIG. (need to buy an extra lift TIG torch) Meets your various welding needs.
- [DIGITAL DISPLAY] Advanced digital display, increases the visual clarity and improves the efficiency of the operation.
- [SYNERGIC CONTROL] When adjusting the wire feeding speed, the voltage will be automatically matched. Suitable for beginners and professionals.
- [SAFETY FIRST] Automatic compensation for voltage fluctuation, over current protection, over load protection.
- SYNERGIC CONTROL: The recommend current and wire feeding speed will be automatically matched after selected diameter of the welding wire(you can choose .030”/.035”/.040" flux core wire). The MIG welder is easier for beginners or those that are learning to weld and want to make small repairs around the house. 1 Free Flux Core Wire .030".
- 3-IN-1 WELDER: 3 welding modes Flux Core Gasless MIG/ Lift TIG/ MMA meet your different requirements (Need to buy extra Lift tig torch). Adjust the current and 10-speed variable feed controls for perfectly managed flux-cored welding of carbon steel, stainless or even thicker steel, Ideal for home DIY, outdoor repairs, rusty metal, farm and road equipment, and maintenance and repairs.
- SAFETY PROTECTION: The welder comes with an attached MIG torch and power cable, you can weld after unpacking the box, it’s convenient to use. Built-in over-current protection, over-load protection, overheating, and over-voltage function that extend the lifespan of the machine.
- PORTABLE AND COMPACT: The machine weighs only 11.79 pounds, and you can freely carry it anywhere with a handle or shoulder strap. Package includes 1* MIG130 Welder, 1* MIG Torch, 1*Ground Clamp, 1* Electronic Holder, 1* .030"/2lb Flux Cored Wire,1* 0.8/.030" conductive Nozzle,1* 0.9/.035" conductive Nozzle,1* Brush&Hammer,1* User Manual.
- WARM SERVICE & 2-YEAR WARRANTY: 30-Day Money Back Guarantee and 2-Year Warranty. Ideal for fathers day gifts. Every single of our welder machines passed various authoritative Laboratory tests in simulating extremely harsh environments before leaving our ARCCAPTAIN factory that conforms to the high standards.
- WELD ANYWHERE: Plug in the Weld-Pak 90i MIG wire feed welder anywhere 120V input power is available; It's designed to use with flux-cored welding wire (1/4” max thickness) or solid MIG wire (3/16" max thickness)
- ACCESSORIES INCLUDED: The machine comes with a full list of accessories including a welding gun, nozzle, contact tip, work cable and clamp; Metal case provides protection from the elements
- LIGHT & PORTABLE: Ideal for maintenance and mobile welders, thanks to its small and lightweight (15 lbs) inverter design and shoulder strap for portability; A good choice for professionals but it’s an easy to use welder for beginners too
- SMOOTH & EASY OPERATION: Has simple control with two knobs for wire speed and voltage; Inverter power source makes it more efficient to operate and provides smoother weld characteristics compared to traditional welders
- PERFECT FOR SMALL WELD JOBS: This machine is best for DIY projects, hobbyists, home repairs and more; Infinite welding voltage allows fine-tuning of weld characteristics
- Synergic Control: The welding parameter is built-in with precise data. It will choose the voltage, amperage and feeding speed that is needed based on welder data, making it much easier for new welders.
- Multi-functions in one machine: Suitable for stick, lift TIG(torch is not included), flux MIG, gas MIG
- Powerful Machine: Up to 200A output current that can weld mild up to 5/32 inch (4.0mm) plate.
- Big enough to apply to 2 and 10 pounds rolls of wire. Ready to feed .030"(0.8mm) with solid core wire, and .035" (0.9mm)with flux core wire.Can Handle E7018 basic electrode.
- Dual voltage input design: Welding machine can be plugged into 110(120)V / 220(230)V dual voltage (Automatic fitting).
- 4 in 1 Welding Machine:This is a multifunctional welding machine,suitable for MMA, Lift TIG, flux MIG, gas MIG,4 welding modes for you to choose.
- Synergic Control: Adjusting the amperage or choosing different wire thicknesses,the voltage and wire feeding speed will automatically change.Even a beginner can easily use it.
- Gas/Gasless Welding: You can choose Flux Core Wire(Gasless) or Solid Wire(Gas). This Welder Can handle 2 lb and 10 lb rolls of wire 0.8mm~1.0mm Flux Core Wire/Solid Wire, MAX Welding Thickness 8.0mm.
- Lift TIG/ARC Welding: Lift TIG available,TIG Torch fits WP17V, not included in the package.TIG Welding thickness 1.0MM-8.0MM, Suitable for thin work-pieces such as stainless steel, alloy steel, carbon steel etc.Arc Welding fits rods E6013.
- Powerful And Safe Machine:This 200A Welding machine can weld mild up to 8.0mm plate,equipped with overload and overheating system,feel free to use,it’s very safe.
- 【EASY TO USE】: The welding machine has included with voltage control knob,wire speed adjustment knob and with synergic control, automatic change of the voltage & wire feeding speed by adjusting the amperage or choosing different thicknesses. Even beginners can use it easily.
- 【POWERFUL AND SAGE WELDER MACHINE】: This 130A Welding machine can weld mild up to 3.0mm plate,equipped with overload and overheating system,feel free to use,it’s very safe.Big enough to handle 2.2 pound rolls of wire.
- 【PORTABLE DESIGN】: Lightweight and compact design, with a comfortable hand grip that makes it easy to carry wherever you want; It only weighs 8.6 lbs., so you can effortlessly take it as far as you can.
- 【WIDE APPLICATIONS】: It can be used with a wide variety of metals and alloys. Suitable for home users, DIY craft enthusiasts, beginners and small projects.
- 【PACKAGE INCLUDES】: 130 MIG welding machine; Mig torch; Ground clamp; Brush&Hammer; 1lb .030" flux cored welding wire; Contact Tip*2.
- 【POWERFUL 3-IN-1 MIG WELDER】The 135Amp MIG welder that included Gas/Solid Wire MIG(GMAW), Gasless Flux Core MIG(FCAW), Stick/MMA. The machine is delivered ready for operation without adjustments with 0.8 mm diameter filler wire.Also, 0.6 mm, 0.9 mm or 1.0mm solid wire or cored wire can be used as filler wire.
- 【SYNERGIC CONTROL】Adjusting the welding power according to sheet thickness affects simultaneously both wire feed speed and amount of current lead to the wire. This is a good starting point for welding in different operating situations.It's suitable for both hobby and professional use.
- 【IGBT TECHNOLOGY】IGBT intelligent inverter technology. IGBT power device with unique control mode improves the reliability of welding machine. The flux core welder works more efficiently, reduces energy loss, and welds better.
- 【PACKAGE INCLUDED】1*MIG/MMA Welder; 1*8.2ft CCA cable with 200A Electrode holder; 1*8.2ft CCA cable with 200A Earth clamp; 1*8.2ft Power cable with American standard plug; 1*8.2ft fixed MIG; 1*slag hammer; 1*User Manual
- 【SAFETY & DURABLE】The machine has passed a variety of professional tests and certifications before leaving the factory.The welding gun has an overheating protector which prevents operation when the machine is overheated. The machine is also protected from too low or too high supply voltage.
- ➠【𝐒𝐲𝐧𝐞𝐫𝐠𝐢𝐜 𝐌𝐈𝐆 𝐂𝐨𝐧𝐭𝐫𝐨𝐥】The wire feeding speed (current) and welding voltage will be automatically matched after selected diameter of the welding wire (.030/.035 inch flux core wire). The MIG welder is easier to make a beginner becoming a master welder.
- ➠【𝐒𝐦𝐚𝐫𝐭 𝐒𝐭𝐢𝐜𝐤 𝐖𝐞𝐥𝐝】Bulit-in smart Hot-start and Arc-force provide easy, quick and reliable arc start, and stable welding current, this mini welder has ideal performance for the most E6013, E6011, E6010, E7018 and E308-16 rods.
- ➠【𝐋𝐢𝐟𝐭 𝐓𝐈𝐆 𝐅𝐮𝐧𝐜𝐭𝐢𝐨𝐧】This 3 in 1 welder has excellent Lift-arc TIG function, just touch the tungsten rod to the workpiece and lift off, easily arc starting, don't need to scratch it, it's like you getting a TIG welder for free.
- ➠【𝐒𝐚𝐟𝐞 𝐚𝐧𝐝 𝐒𝐭𝐚𝐛𝐥𝐞】This multiprocess welder built-in automatic Anti-stick, compensation for voltage fluctuation, over current protection, over heat protection, short circuit damage protection, to make sure the welding kit safely operation and long life.
- ➠【𝐖𝐢𝐝𝐞 𝐀𝐩𝐩𝐥𝐢𝐜𝐚𝐭𝐢𝐨𝐧 𝐚𝐧𝐝 𝐏𝐨𝐫𝐭𝐚𝐛𝐥𝐞】The wire feed welder is capable of welding all kinds of ferrous metals such as carbon steel, medium carbon steel, mild steel, stainless steel and cast iron. Only weighs 10.1 lbs, easy to carry with a handle or shoulder strap(included), very suitable for outdoor maintenance, farm, road equipment, and home DIY.
- Simple user interface - Seven segment display with basic knob controls.
- Process Capabilities - MIG, Flux-Cored and Spool Gun.
- Dual Input Voltage - 120V and 230V inputs so you can plug into any common power supply.
- Ergonomic Case - Sleek and robust case design with multiple lift points for ease of mobility around the shop.
- Lightweight and Portable - Only 41 lbs
- 【POWERFUL 3-IN-1 WELDER】Composed with Flux MIG, Lift TIG and Stick/MMA. Our powerful 3-in-1 welding machine meets your requirement for different welding situations like home DIY, outdoor maintenance and repairs, etc. (NOTE: the lift tig torch is not included)
- 【SYNERGIC CONTROL】Equipped with precise data, this flux core welder will automatically match the most suitable voltage, wire feeding speed by adjusting amperage, which is quite friendly for both professional welding worker and beginner. You can also adjust machine parameters by manually In order to best suit for your demand.
- 【SAFE & INTELLIGENT】Our MIG welder features overheat and overload protection will automatically shut off while overheated, and the built-in fan will consistently cool down your welder for 1-2 mins after shutdown. Additionally, the intelligent IGBT technology helps the welder reduce energy loss and works more efficiently.
- 【LIGHTWEIGHT & DURABLE】Item Dimensions: 13.6(L) x 6.6(W) x 11.15(H) inches, welder machine weight: 10.14lbs. This lightweight 135amp stick welder designed with two portable handles, allows you to take it anywhere, and you can add a shoulder belt by your own if need. Besides, IP21 water rating better protect your welder and extend its service life.
- 【SET INCLUDES】To spend you less money and bring you more convenience, our 3-in-1 welder set includes a solar powered auto darkening welding helmet (viewing size: 3.66"x1.69"), a pair of 932°F/500℃ heat resistant leather welding gloves and a roll of E71T-GS .030" 2lb flux core welding wire.
Last update on 2024-04-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.