“This site contains affiliate links for which OEMDTC may be compensated” |
May 20, 2020 NHTSA CAMPAIGN NUMBER: 20V292000
Insufficient Rear Impact Protection/FMVSS 224
In the event of a rear impact crash, the other vehicle can travel under the rear of the vacuum excavator, increasing the risk of serious injury or death to someone in the other vehicle.
NHTSA Campaign Number: 20V292
Manufacturer Vac-Tron Equipment, LLC
Components STRUCTURE
Potential Number of Units Affected 110
Summary
Vac-Tron Equipment, LLC (Vac-Tron), a subsidiary of Vermeer Manufacturing Company (Vermeer), is recalling certain 2016-2020 CS500DT, CS570GT, CS573GT, CS800DT, CS800GT, CS1270GT, CS1270SGT, and CS1273GT Vacuum Excavator trailers. The rear most extremity extends too far beyond the rear of the trailer frame, reducing impact protection. As such, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 224, “Rear Impact Protection.”
Remedy
Vac-Tron will notify owners, and Vermeer dealers will install remedy kits provided by Vac-Tron, free of charge. The recall began July 14, 2020. Owners may contact Vac-Tron customer service at 1-888-822-8766. Vac-Tron’s number for this recall is VVK0008.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Vac-Tron Equipment, LLC
Trenchless
Okahumpka, FL 34762 USA
FIELD CAMPAIGN
SERVICE BULLETIN # SVV2020-012
DATE: 30 June 2020
CAMPAIGN TYPE: | Mandatory-Product Safety |
CAMPAIGN CATEGORY: | Kit and Bulletin |
MACHINE /
ATTACHMENT MODEL (S) : |
Serial Numbers | ||
Included | Excluded | Kit Version | |
CSGT | See attached listing on pages 4-5 of this Bulletin for specific VIN and Serial/Unit numbers | N/A | VVK01 |
CS873GT | |||
CS870GT | |||
CS870DT | |||
CS800GT | |||
CS573GT | |||
CS570GT | |||
CS500DT | |||
CS1273GT | See attached listing on Page 5 of this Bulletin for specific VIN and Serial/Unit numbers | N/A | VVK02 |
CS1270SGT | |||
CS1270GT |
Subject:
PRODUCT SAFETY RECALLFIRST NOTICE |
Light Relocation, Reflector, Conspicuity Tape Installation, and Rear Extension Installation Kit
(VVK00-0008)
Background:
INADEQUATE LIGHTING, REFLECTORS, CONSPICUTITY TAPE AND REAR EXTENSION
The lighting, side and rear reflectors and conspicuity tape do not meet US or Canada
Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) governmental regulation 108 for the Unites States, Canada and Mexico. The trailers may not have an extended lower rear chassis, reducing rear impact protection and does not meet US or Canada Federal Motor Vehicle Standard (FMVSS/CMVSS) government regulation 223 for the United States, Canada and Mexico.
DEATH OR SERIOUS INJURY POSSIBLE
When towing or parking the vacuum excavator on public roadways, a crash may occur resulting in death or serious injury resulting from a driver(s) of other vehicle(s) not seeing the vacuum excavator at night or during limited sunlight and strike the vacuum excavator. To reduce the potential of this occurring, vehicle lights will be relocated, additional reflectors and conspicuity tape are being added.
In the event of a rear impact crash, the other vehicle may travel under the rear of the vacuum excavator, increasing the risk of serious injury or death to someone in the other vehicle or to the towing vehicle occupants.
Property or equipment damage may also occur.
Solution:
IMMEDIATE MACHINE MODIFICATIONS REQUIRED
VVK00-0008 has been created to provide the necessary parts and instructions to relocate the vehicle lights, add reflex reflectors, add conspicuity tape to the sides and rear, and add a rear extension. This kit must be installed as soon as possible.
Please be reminded that it is a violation of Federal law for you to sell or lease the machines covered by this notification until this recall has been performed on these machines. Substantial civil penalties apply to violations of this law.
DEALER PARTICIPATION
REVIEW REPORT, ORDER KITS, CONTACT CUSTOMERS
- Reports will be emailed during the week of June 30, 2020, to dealerships shown in our records which have units in their territory affected by this Alert. Please review the report for accuracy, including owner and/or address changes.
If the information contained in the report is NOT correct, please notify the Product Safety Department on or before July 13, 2020 at:
Telephone: 641-621-7060
Fax: 641-621-8562
Email: productsafety@vermeer.com
- Dealerships Order Kits by calling Vac-Tron at 888-822-8766.
Each dealership should determine the quantity of Kits to order initially depending upon the number of units that may be available for immediate upgrade. Do not order more Kits than needed for immediate installation.
- Contact your affected customer(s) to schedule a mutually acceptable time to upgrade their machine. Note: Letters will be sent to the customer(s) on or about July 14, 2020. Also refer to Owner Notification section below.
If you have any questions concerning the installation of VVK00-0008, please contact the Vac-Tron Service Department. Vermeer Corporation is assisting Vac-Tron with the administration of this campaign.
REIMBURSEMENT
Upon completion of each Kit installation, a campaign Warranty Claim must be submitted to the Vermeer Corporation Warranty Department for reimbursement of the parts cost and labor of the Kit.
This kit will reimburse 6 labor hours.
Note: Future notices to dealers and owners are dependent upon the receipt of Warranty Claim.
OWNER NOTIFICATION
Sample Letter: Included at the end of this Bulletin is a sample letter which will be sent by Vermeer Corporation directly to the Owners on or about July 14, 2020, via USPS certified/registered mail. Owner registrations indicate no translations are required for this campaign. The owner letter will be available in English only.
This owner notification/letter instructs the owner to contact their local dealership to arrange for a time to have the Kit installed. After receiving VVK00-0008 from Vac-Tron, you must contact your affected customer(s) immediately and schedule a mutually acceptable time to upgrade their machine.
We regret any inconvenience these corrective measures may cause you. This required work is for safety of the safety of the towing vehicle driver and occupants as well as other traveling on public roadways or in the immediate are while being towed. We hope you agree the safety benefits surpass the inconvenience.
VAC-TRON EQUIPMENT, INC.
Attachment:
VVK00-0008 Kit Instructions
SEOCONTENT-START
AFFECTED MACHINES – VVK01-0008 | ||||||
MODEL | VIN | SERIAL/UNIT | MODEL | VIN | SERIAL/UNIT | |
CS870GT | 5HZBF1625HLKH1441 | 171497 | CS870GT | 5HZBF1625HLHH1313 | 171336 | |
CS500DT | 5HZBF1624GLDG1147 | 161099 | CS870GT | 5HZBF1620HLHH1333 | 171371 | |
CS570GT | 5HZBF1419GLEG3103 | 161158 | CS870GT | 5HZBF1621HLHH1339 | 171380 | |
CS570GT | 5HZBF1621JLBJ1151 | 181084 | CS870GT | 5HZBF1628HLHH1340 | 171381 | |
CS573GT | 5HZBF162XJLBJ1150 | 181078 | CS870GT | 5HZBF1622HLHH1351 | 171391 | |
CS573GT | 5HZBF1628JLEJ1351 | 181389 | CS870GT | 5HZBF1624HLHH1352 | 171392 | |
CS800GT | 5HZBF1623GLKG1277 | 161325 | CS870GT | 5HZBF1626HLJH1400 | 171432 | |
CS800GT | 5HZBF1621GLLG1278 | 161326 | CS870GT | 5HZBF1629HLKH1426 | 171477 | |
CS800GT | 5HZBF1623GLLG1279 | 161327 | CS870GT | 5HZBF1626HLLH1466 | 171547 | |
CS800GT | 5HZBF1624HLEH1214 | 171208 | CS870GT | 5HZBF1628HLLH1467 | 171548 | |
CS800GT | 5HZBF1620HLDH1188 | 171215 | CS870GT | 5HZBF1622JLAJ1155 | 181082 | |
CS800GT | 5HZBF1629JLHJ1416 | 181492 | CS870GT | 5HZBF1620JLBJ1156 | 181083 | |
CS800GT | 5HZBF1629KLAK1134 | 191131 | CS870GT | 5HZBF1625JLAJ1120 | 181089 | |
CS870DT | 5HZBF1621HLJH1370 | 171428 | CS870GT | 5HZBF1623JLCJ1171 | 181110 | |
CS870GT | 5HZBF1622GLBG1125 | 161066 | CS870GT | 5HZBF1629JLCJ1174 | 181118 | |
CS870GT | 5HZBF1620GLCG1126 | 161068 | CS870GT | 5HZBF1620JLCJ1175 | 181119 | |
CS870GT | 5HZBF1622GLCG1127 | 161069 | CS870GT | 5HZBF1622JLCJ1176 | 181120 | |
CS870GT | 5HZBF1623GLCG1136 | 161084 | CS870GT | 5HZBF1624JLCJ1177 | 181121 | |
CS870GT | 5HZBF1628GLDG1149 | 161111 | CS870GT | 5HZBF1626JLCJ1178 | 181122 | |
CS870GT | 5HZBF1624GLDG1150 | 161112 | CS870GT | 5HZBF1624JLCJ1180 | 181123 | |
CS870GT | 5HZBF1628GLFG1190 | 161186 | CS870GT | 5HZBF1623HLJH1399 | 181133 | |
CS870GT | 5HZBF1621GLFG1192 | 161190 | CS870GT | 5HZBF1628JLEJ1270 | 181263 | |
CS870GT | 5HZBF1623GLFG1193 | 161191 | CS870GT | 5HZBF162XJLEJ1271 | 181264 | |
CS870GT | 5HZBF1625GLFG1194 | 161192 | CS870GT | 5HZBF1620JLEJ1280 | 181276 | |
CS870GT | 5HZBF1627GLFG1195 | 161193 | CS870GT | 5HZBF1628JLEJ1303 | 181309 | |
CS870GT | 5HZBF1620GLJG1251 | 161297 | CS870GT | 5HZBF1624JLFJ1382 | 181346 | |
CS870GT | 5HZBF1626GLLG1292 | 161347 | CS870GT | 5HZBF1626JLEJ1333 | 181358 | |
CS870GT | 5HZBF1628HLAH1141 | 171069 | CS870GT | 5HZBF1625JLEJ1341 | 181379 | |
CS870GT | 5HZBF1627HLBH1148 | 171081 | CS870GT | 5HZBF1629JLEJ1343 | 181387 | |
CS870GT | 5HZBF1626HLCH1175 | 171135 | CS870GT | 5HZBF1620JLEJ1344 | 181388 | |
CS870GT | 5HZBF1628HLCH1176 | 171137 | CS870GT | 5HZBF1626JLEJ1347 | 181391 | |
CS870GT | 5HZBF1622HLDH1189 | 171154 | CS870GT | 5HZBF162XJLHJ1392 | 181396 | |
CS870GT | 5HZBF1620HLDH1191 | 171157 | CS870GT | 5HZBF1621JLHJ1393 | 181442 | |
CS870GT | 5HZBF1626HLEH1215 | 171209 | CS870GT | 5HZBF1629JLJJ1430 | 181486 | |
CS870GT | 5HZBF1628HLEH1216 | 171210 | CS870GT | 5HZBF1620JLHJ1417 | 181497 | |
CS870GT | 5HZBF1625HLFH1239 | 171240 | CS870GT | 5HZBF162XJLKJ1486 | 181648 | |
CS870GT | 5HZBF1621HLFH1254 | 171258 | CS870GT | 5HZBF1625JLKJ1492 | 181659 | |
CS870GT | 5HZBF162XHLFH1267 | 171276 | CS870GT | 5HZBF1629JLKJ1494 | 181662 | |
CS870GT | 5HZBF1621HLFH1268 | 171277 | CS870GT | 5HZBF1624JLMJ1506 | 181698 | |
CS870GT | 5HZBF1628HLGH1285 | 171307 | CS870GT | 5HZBF1627KLAK1150 | 191159 | |
CS870GT | 5HZBF1625HLGH1292 | 171308 | CS870GT | 5HZBF1629KLAK1151 | 191169 | |
CS870GT | 5HZBF1622HLGH1296 | 171312 | CS870GT | 5HZBF1620KLAK1152 | 191197 |
AFFECTED MACHINES – VVK01-0008 | ||||||
MODEL | VIN | SERIAL/UNIT | MODEL | VIN | SERIAL/UNIT | |
CS870GT | 5HZBF1624KLMJ1572 | 191232 | CS873GT | 5HZBF1625JLMJ1501 | 181683 | |
CS873GT | 5HZBF1629HLLH1459 | 171533 | CS873GT | 5HZBF1622KLKJ1502 | 191139 | |
CS873GT | 5HZBF1624JLDJ1246 | 181225 | CSGT | 5HZB192W4KK002001 | 191288 | |
CS873GT | 5HZBF1626JLDJ1247 | 181226 | CSGT | 5HZB192W3KK002006 | 191372 | |
CS873GT | 5HZBF1628JLDJ1248 | 181227 |
AFFECTED MACHINES – VVK02-0008 | ||||||
MODEL | VIN | SERIAL/UNIT | MODEL | VIN | SERIAL/UNIT | |
CS1270GT | 5HZBF1922JLAJ2110 | 181135 | CS1273GT | 5HZBF1921JLHJ2278 | 181500 | |
CS1270GT | 5HZBF1924JLCJ2146 | 181076 | CS1273GT | 5HZBF1929JLKJ2348 | 181705 | |
CS1270SGT | 5HZBF1923HLJH2211 | 171145 |
NHTSA SAFETY RECALL NUMBER 20V-289 and 20V-292
IMPORTANT SAFETY RECALL
First Notice Light Relocation, Reflector, Conspicuity Tape and Rear Extension Installation Kit (VVK00-008) |
Model: «Model»
This notice applies to your vehicle, Serial No: «VIN» Unit No: «PART_SRL» |
VIA USPS CERTIFIED/REGISTERED MAIL
July 14, 2020
Dear «MODEL» Owner:
This notice is sent to you in accordance with the requirements of the U.S. National Traffic and Motor Vehicle Safety Act.
Vermeer has decided that a defect, that relates to motor vehicle safety, exists in certain model year 2016-2020 Vermeer «MODEL».
INADEQUATE LIGHTING, REFLECTORS, CONSPICUTITY TAPE AND REAR EXTENSION
The lighting, side and rear reflectors and conspicuity tape do not meet US or Canada Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) governmental regulation 108 for the Unites States, Canada and Mexico.
The trailers may not have an extended lower rear chassis, reducing rear impact protection and does not meet US or Canada Federal Motor Vehicle Standard (FMVSS/CMVSS) government regulation 223 for the United States, Canada and Mexico.
DEATH OR SERIOUS INJURY POSSIBLE
When towing or parking the vacuum excavator on public roadways, a crash may occur resulting in death or serious injury resulting from a driver(s) of other vehicle(s) not seeing the vacuum excavator at night or during limited sunlight and strike the vacuum excavator. To reduce the potential of this occurring, vehicle lights will be relocated, additional reflectors and conspicuity tape are being added.
In the event of a rear impact crash, the other vehicle may travel under the rear of the vacuum excavator, increasing the risk of serious injury or death to someone in the other vehicle or to the towing vehicle occupants.
Property or equipment damage may also occur.
IMMEDIATE MACHINE MODIFICATIONS REQUIRED
VVK00-008 has been created to provide the necessary parts and instructions to relocate the vehicle lights, add reflex reflectors, add conspicuity tape to the sides and rear, and add a rear extension. This kit must be installed as soon as possible.
Please contact your authorized, independent Vermeer dealer immediately to arrange a mutually acceptable time and location to install VVK00-008 at no cost to you for labor or materials. The installation of this kit is estimated at 6 hours of labor. If the Vermeer dealer travels to the unit to install the kit, costs may be incurred by the owner. You must have your machine upgraded for these safety features.
Contact your local Vermeer Dealer: «Service_Dealer_Name» «Serv_Dealer_Add1» «Serv_Dealer_Add2» «Serv_Dealer_City» «Serv_Dealer_St» «Serv_Dealer_Zip» «SERV_DEALER_COUNTRY» Telephone: «Serv_Dealer_Phone» |
According to our records, you currently own a Vermeer «MODEL» ^[PRODUCT TYPE]. The Model and Serial Number of the «MODEL» is shown at the top right of this letter. If you no longer own this unit, please notify the Product Safety Department at:
Toll Free: 800-829-0051, extension 7060
Telephone: 641-621-7060
E-mail: productsafety@vermeer.com
If possible, please provide the name and address of the new owner. Vermeer Corporation is Vac-Tron with the administration of this campaign.
We regret any inconvenience these corrective measures may cause you. This required work is for safety of the safety of the towing vehicle driver and occupants as well as other traveling on public roadways or in the immediate are while being towed. We hope you agree the safety benefits surpass the inconvenience.
Very truly yours,
VAC-TRON EQUIPMENT, LLC
Federal regulations require that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten (10) days.
If the authorized dealer has failed or is unable to remedy the defect without charge and within a reasonable time, contact Vermeer Product Safety by email at productsafety@vermeer.com or by calling 800-829-0051 or 641-621-7060. You may also submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, D.C. 20590 or call the Vehicle Safety Hotline at 888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov
Vac-Tron Equipment, LLC
Trenchless
Okahumpka, FL 34762 USA
FIELD CAMPAIGN KIT # VVK00-0008
DATE: 30 June 2020
For Dealer Reference: Service Bulletin # SVV2020-012
Light Relocation, Reflector, Conspicuity Tape and Rear Extension Installation Kit
CAMPAIGN TYPE: | Mandatory-Product Safety |
CAMPAIGN CATEGORY: | Kit and Bulletin |
MACHINE / ATTACHMENT MODEL (S) : |
Serial Numbers | |||
Included | Excluded | Kit Version | ||
CSGT | See attached listing on pages 18–19 of this Kit
Instructions for specific VIN and Serial/Unit numbers |
N/A | VVK01 | |
CS873GT | ||||
CS870GT | ||||
CS870DT | ||||
CS800GT | ||||
CS573GT | ||||
CS570GT | ||||
CS500DT | ||||
CS1273GT | See attached listing on Page 19 of this Kit Instructions for specific VIN and Serial/Unit
numbers |
N/A | VVK02 | |
CS1270SGT | ||||
CS1270GT |
PRODUCT SAFETY ALERT |
PURPOSE: INADEQUATE LIGHTING, REFLECTORS, CONSPICUTITY TAPE, AND REAR EXTENSION The lighting, side and rear reflectors and conspicuity tape do not meet US or Canada Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) governmental regulation 108 for the United States, Canada and Mexico. The trailers may not have an extended lower rear chassis, reducing rear impact protection and does not meet US or Canada Federal Motor Vehicle Standard (FMVSS/CMVSS) government regulation 223 for the United States, Canada and Mexico. When towing or parking the vacuum excavator on public roadways, a crash may occur resulting in death or serious injury resulting from a driver(s) of other vehicle(s) not seeing the vacuum excavator at night or during limited sunlight and strike the vacuum excavator. To reduce the potential of this occurring, vehicle lights will be relocated, additional reflectors and conspicuity tape are being added. In the event of a rear impact crash, the other vehicle may travel under the rear of the vacuum excavator, increasing the risk of serious injury or death to someone in the other vehicle or to the towing vehicle occupants. Property or equipment damage may also occur.
Shutdown Procedure
STOPPING THE MACHINE
For your safety and the safety of others, follow shutdown procedure before working on the machine for any reason, including servicing, maintaining, cleaning, inspecting, unclogging or transporting machine, or as otherwise directed in Operator’s manual.
Step 1: Make sure end of vacuum hose is clear of all spoils, debris, and other materials.
Step 2: Push Throttle Control left several times to slow engine. Idle engine five minutes to allow vacuum pump (with Reverse Flow Lever – Neutral) to cool down. This helps to prevent the buildup of condensation.
Step 3: Turn Keyswitch OFF to shut down engine.
Step 4: Drain Filter Housing.
PROCEDURE 1:
- Select the angled bracket with the amber colored marker light. Align the bracket with the edge of the curb side fender as shown below. Ref. 1, Fig 1.
- Mark the light bracket hole locations onto the fender and drill (3) Ø9/32” (7.15 mm) holes through the I-beam.
- Attach the marker light bracket with the supplied hardware. Ref. 1, 2, 3, 4, and 5 Fig. 1.
- Connect one end of the 10 ft (30 cm) length of dual core wire to the marker lamp using the butt connectors. 5 and 6, Fig. 1.
- Complete all steps for the street side of the trailer.
PROCEDURE 2:
- Select the angled bracket with the red colored marker light. Align the bracket with the edge of the curb side fender as shown below. Ref. 1, Fig 1.
- Mark the light bracket hole locations onto the fender and drill (3) Ø9/32” (7.15 mm) holes through the I-beam.
- Attach the marker light bracket with the supplied hardware. Ref. 1, 2, 3, 4, and 5 Fig.2.
- Connect one end of the 5 ft (152.4 cm) length of dual core wire to the marker lamp using the butt connectors. 5 and 6, Fig.
- Loom all exposed wires. Ref. 7, Fig1 and Ref. 7 Fig. 2.
- Connect wires from the amber marker light, red marker light on the fender to the red marker light in the bumper as shown using the heat shrink butt connectors.
PROCEDURE 3:
- Clean area where the conspicuity tape will be installed with light soap and water. Areas with damaged paint or heavy corrosion should be prepped, painted, and thoroughly dry before applying conspicuity tape.
- Refer to the illustration and install the conspicuity tape in the locations shown. Ref. 1 and 2, Fig. 3.
- Repeat for the opposite side of the trailer.
PROCEDURE 4: (APPLIES TO KIT VVK01 AND VVK03)
- Clean area where the conspicuity tape will be installed with light soap and water. Areas with damaged paint or heavy corrosion should be prepped, painted, and thoroughly dry before applying the conspicuity tape.
- Refer to the illustration and install each of the white conspicuity tape on the debris tank door Ref 1, Fig. 4.
PROCEDURE 5:
- For units with kit VVK01, skip to set 2. For units with kit VVK02 (CS1200), use a grinder to remove 2” from the corner stiffener located under the trailer. Repeat on opposite side of trailer.
- Grind off the paint and rust where the cross members provided are to be installed. Refer to the figure in Step 2.
- Position the reinforcement members as indicated below Ref. 1 or 2 Fig. 5.
- Weld the reinforcement members into place as indicated in the figures below.
PROCEDURE 6:
- Ensure the debris tank is empty. Using suitable blocking, block debris tank to prevent shifting. Debris tank weighs approximately 1,000 lb (455 kg).
- Remove the cotter pin on both sides.
- Push the headed pins out to be flush with the inner side of the tank hinges. Be careful not to push the pin through the hinge.
- Push the headed pins out to be flush with the inner side of the tank hinges. Be careful not to push the pin through the hinge.
- Use a suitable lifting device when installing the bumper. Bumper weight is approximately 120 lb (55 kg).
- Inspect the tank hinges connected to the bumper. Hinges with the single hole configuration shown must be replaced. If the hinges have a 2-hole configuration, skip to step 9.
- Use a cutting torch to remove the (4) tank hinges from the bumper. Grind away residual slag.
- Remove all damaged paint down to bare metal. Repaint all affected areas.
- Install the bumper and align the bolt holes with the tank hinges.
- Push the headed pins back into position and replace the cotter pins on both sides.
- Install the hardware Ref. 3, 4, and 5 Figure 6. Tighten the bolts to 644 ft-lb (873 Nm).
SEOCONTENT-START
AFFECTED MACHINES – VVK01-0008 | ||||||
MODEL | VIN | SERIAL/UNIT | MODEL | VIN | SERIAL/UNIT | |
CS870GT | 5HZBF1625HLKH1441 | 171497 | CS870GT | 5HZBF1625HLHH1313 | 171336 | |
CS500DT | 5HZBF1624GLDG1147 | 161099 | CS870GT | 5HZBF1620HLHH1333 | 171371 | |
CS570GT | 5HZBF1419GLEG3103 | 161158 | CS870GT | 5HZBF1621HLHH1339 | 171380 | |
CS570GT | 5HZBF1621JLBJ1151 | 181084 | CS870GT | 5HZBF1628HLHH1340 | 171381 | |
CS573GT | 5HZBF162XJLBJ1150 | 181078 | CS870GT | 5HZBF1622HLHH1351 | 171391 | |
CS573GT | 5HZBF1628JLEJ1351 | 181389 | CS870GT | 5HZBF1624HLHH1352 | 171392 | |
CS800GT | 5HZBF1623GLKG1277 | 161325 | CS870GT | 5HZBF1626HLJH1400 | 171432 | |
CS800GT | 5HZBF1621GLLG1278 | 161326 | CS870GT | 5HZBF1629HLKH1426 | 171477 | |
CS800GT | 5HZBF1623GLLG1279 | 161327 | CS870GT | 5HZBF1626HLLH1466 | 171547 | |
CS800GT | 5HZBF1624HLEH1214 | 171208 | CS870GT | 5HZBF1628HLLH1467 | 171548 | |
CS800GT | 5HZBF1620HLDH1188 | 171215 | CS870GT | 5HZBF1622JLAJ1155 | 181082 | |
CS800GT | 5HZBF1629JLHJ1416 | 181492 | CS870GT | 5HZBF1620JLBJ1156 | 181083 | |
CS800GT | 5HZBF1629KLAK1134 | 191131 | CS870GT | 5HZBF1625JLAJ1120 | 181089 | |
CS870DT | 5HZBF1621HLJH1370 | 171428 | CS870GT | 5HZBF1623JLCJ1171 | 181110 | |
CS870GT | 5HZBF1622GLBG1125 | 161066 | CS870GT | 5HZBF1629JLCJ1174 | 181118 | |
CS870GT | 5HZBF1620GLCG1126 | 161068 | CS870GT | 5HZBF1620JLCJ1175 | 181119 | |
CS870GT | 5HZBF1622GLCG1127 | 161069 | CS870GT | 5HZBF1622JLCJ1176 | 181120 | |
CS870GT | 5HZBF1623GLCG1136 | 161084 | CS870GT | 5HZBF1624JLCJ1177 | 181121 | |
CS870GT | 5HZBF1628GLDG1149 | 161111 | CS870GT | 5HZBF1626JLCJ1178 | 181122 | |
CS870GT | 5HZBF1624GLDG1150 | 161112 | CS870GT | 5HZBF1624JLCJ1180 | 181123 | |
CS870GT | 5HZBF1628GLFG1190 | 161186 | CS870GT | 5HZBF1623HLJH1399 | 181133 | |
CS870GT | 5HZBF1621GLFG1192 | 161190 | CS870GT | 5HZBF1628JLEJ1270 | 181263 | |
CS870GT | 5HZBF1623GLFG1193 | 161191 | CS870GT | 5HZBF162XJLEJ1271 | 181264 | |
CS870GT | 5HZBF1625GLFG1194 | 161192 | CS870GT | 5HZBF1620JLEJ1280 | 181276 | |
CS870GT | 5HZBF1627GLFG1195 | 161193 | CS870GT | 5HZBF1628JLEJ1303 | 181309 | |
CS870GT | 5HZBF1620GLJG1251 | 161297 | CS870GT | 5HZBF1624JLFJ1382 | 181346 | |
CS870GT | 5HZBF1626GLLG1292 | 161347 | CS870GT | 5HZBF1626JLEJ1333 | 181358 | |
CS870GT | 5HZBF1628HLAH1141 | 171069 | CS870GT | 5HZBF1625JLEJ1341 | 181379 | |
CS870GT | 5HZBF1627HLBH1148 | 171081 | CS870GT | 5HZBF1629JLEJ1343 | 181387 | |
CS870GT | 5HZBF1626HLCH1175 | 171135 | CS870GT | 5HZBF1620JLEJ1344 | 181388 | |
CS870GT | 5HZBF1628HLCH1176 | 171137 | CS870GT | 5HZBF1626JLEJ1347 | 181391 | |
CS870GT | 5HZBF1622HLDH1189 | 171154 | CS870GT | 5HZBF162XJLHJ1392 | 181396 | |
CS870GT | 5HZBF1620HLDH1191 | 171157 | CS870GT | 5HZBF1621JLHJ1393 | 181442 | |
CS870GT | 5HZBF1626HLEH1215 | 171209 | CS870GT | 5HZBF1629JLJJ1430 | 181486 | |
CS870GT | 5HZBF1628HLEH1216 | 171210 | CS870GT | 5HZBF1620JLHJ1417 | 181497 | |
CS870GT | 5HZBF1625HLFH1239 | 171240 | CS870GT | 5HZBF162XJLKJ1486 | 181648 | |
CS870GT | 5HZBF1621HLFH1254 | 171258 | CS870GT | 5HZBF1625JLKJ1492 | 181659 | |
CS870GT | 5HZBF162XHLFH1267 | 171276 | CS870GT | 5HZBF1629JLKJ1494 | 181662 | |
CS870GT | 5HZBF1621HLFH1268 | 171277 | CS870GT | 5HZBF1624JLMJ1506 | 181698 | |
CS870GT | 5HZBF1628HLGH1285 | 171307 | CS870GT | 5HZBF1627KLAK1150 | 191159 | |
CS870GT | 5HZBF1625HLGH1292 | 171308 | CS870GT | 5HZBF1629KLAK1151 | 191169 | |
CS870GT | 5HZBF1622HLGH1296 | 171312 | CS870GT | 5HZBF1620KLAK1152 | 191197 | |
AFFECTED MACHINES – VVK01-0008 | ||||||
MODEL | VIN | SERIAL/UNIT | MODEL | VIN | SERIAL/UNIT | |
CS870GT | 5HZBF1624KLMJ1572 | 191232 | CS873GT | 5HZBF1625JLMJ1501 | 181683 | |
CS873GT | 5HZBF1629HLLH1459 | 171533 | CS873GT | 5HZBF1622KLKJ1502 | 191139 | |
CS873GT | 5HZBF1624JLDJ1246 | 181225 | CSGT | 5HZB192W4KK002001 | 191288 | |
CS873GT | 5HZBF1626JLDJ1247 | 181226 | CSGT | 5HZB192W3KK002006 | 191372 | |
CS873GT | 5HZBF1628JLDJ1248 | 181227 | ||||
AFFECTED MACHINES – VVK02-0008 | ||||||
MODEL | VIN | SERIAL/UNIT | MODEL | VIN | SERIAL/UNIT | |
CS1270GT | 5HZBF1922JLAJ2110 | 181135 | CS1273GT | 5HZBF1921JLHJ2278 | 181500 | |
CS1270GT | 5HZBF1924JLCJ2146 | 181076 | CS1273GT | 5HZBF1929JLKJ2348 | 181705 | |
CS1270SGT | 5HZBF1923HLJH2211 | 171145 |
FIGURE 1 Parts List | ||||
REF. NO. | PART NO. | DESCRIPTION | VVK01 QTY. | VVK02 QTY |
1 | 135500266 | MARKER LIGHT BRACKET | 2 | 2 |
2 | P-4190 | LED MARKER LIGHT, AMBER | 2 | 2 |
3 | P-1473 | 1/4-20 X 1 HEX HEAD BOLT | 6 | 6 |
4 | P-1472 | 1/4 ID FLAT WASHER | 6 | 6 |
5 | P-2782 | 1/4-20 NYLON LOCKNUT | 6 | 6 |
6 | P-1054 | 10’ (304.8 cm) LENGTH DUAL CORE CONDUCTOR WIRE | 2 | 2 |
7 | P-2762 | 1/2″ SPLIT WIRE LOOM, 10’ (304.8 cm) LENGTH | 1 | 1 |
8 | P-2369 | 16-14 HEAT SEAL BUTT CONNECTOR BLUE | 4 | 4 |
9 | P-1301 | ZIP TIE | 12 | 12 |
FIGURE 2 Parts List | ||||
REF. NO. | PART NO. | DESCRIPTION | VVK01 QTY. | VVK02 QTY. |
1 | 135500266 | MARKER LIGHT BRACKET | 2 | 2 |
2 | P-4189 | LED MARKER LIGHT, RED | 2 | 2 |
3 | P-1473 | 1/4-20 X 1 HEX HEAD BOLT | 6 | 6 |
4 | P-1472 | 1/4 ID FLAT WASHER | 6 | 6 |
5 | P-2782 | 1/4-20 NYLON LOCKNUT | 6 | 6 |
6 | P-1054 | 5’ (152.4 cm) LENGTH DUAL CORE CONDUCTOR WIRE | 2 | 2 |
7 | P-2762 | 1/2″ SPLIT WIRE LOOM, 5’ (152.4 cm) LENGTH | 1 | 1 |
8 | P-2369 | 16-14 HEAT SEAL BUTT CONNECTOR BLUE | 4 | 4 |
9 | P-1301 | ZIP TIE | 12 | 12 |
10 | 135500217 | 12-10 HEAT SEAL BUTT CONNECTOR | 4 | 4 |
FIGURE 3 Parts List | ||||
REF. NO. | PART NO. | DESCRIPTION | VVK01 QTY. | VVK02 QTY. |
1 | P-0485 | 2” (2.54 cm) WIDE, 90” (228.6 cm) LONG | 2 | 2 |
2 | P-0485 | 2” (2.5 cm) WIDE, 54”(137.2 cm) LONG | 2 | 2 |
FIGURE 4 Parts List | ||||
REF. NO. | PART NO. | DESCRIPTION | VVK01 QTY. | VVK02 QTY. |
1 | P-5783 | WHITE CONSPICUITY TAPE, 12” LENGTH | 4 | 4 |
FIGURE 5 Parts List | ||||
REF. NO. | PART NO. | DESCRIPTION | VVK01 QTY. | VVK02 QTY. |
1 | 135500310 | REINF. MEMBER | 2 | 0 |
2 | 135500311 | REINF. MEMBER | 0 | 2 |
FIGURE 8 Parts List | ||||
REF. NO. | PART NO. | DESCRIPTION | VVK01 QTY. | VVK02 QTY. |
1 | 135500268 | REAR EXTENSION | 1 | 0 |
2 | 135500267 | REAR EXTENSION | 0 | 1 |
A | SA-4471 | HEADED PIN (EXISTING ON TRAILER) | 2 | 2 |
3 | 135500218 | 1-8 X 6-1/2 HEX BOLT | 2 | 2 |
4 | P-3827 | 1 ID FLAT WASHER | 4 | 4 |
5 | P-2626 | 1-8 PREVAILING TORQUE NUT | 2 | 2 |
6 | 135500216 | TANK HINGE BRACKET | 4 | 4 |
40 Affected Products
Vehicles
MAKE | MODEL | YEAR |
VAC-TRON | CS 1270 GT | 2016-2020 |
VAC-TRON | CS 1270 SGT | 2016-2020 |
VAC-TRON | CS 1273 GT | 2016-2020 |
VAC-TRON | CS 500 DT | 2016-2020 |
VAC-TRON | CS 570 GT | 2016-2020 |
VAC-TRON | CS 573 GT | 2016-2020 |
VAC-TRON | CS 800 DT | 2016-2020 |
VAC-TRON | CS 800 GT | 2016-2020 |
9 Associated Documents
Non-Compliance Notice 573 Report
RCLRPT-20V292-5135.PDF 217.449KB
Recall Acknowledgement
RCAK-20V292-3283.pdf 245.439KB
Miscellaneous Document- BEFORE AND AFTER
RMISC-20V292-2126.pdf 531.478KB
Remedy Instructions and TSB
RCRIT-20V292-7834.pdf 2332.726KB
Safety Bulletin
RCSB-20V292-1999.pdf 1224.089KB
Recall Quarterly Report #2, 2020-4
RCLQRT-20V292-9770.PDF 211.241KB
Recall Quarterly Report #1, 2020-3
RCLQRT-20V292-3582.PDF 211.137KB
Owner Notification Letter(Part 577)
RCONL-20V292-2406.pdf 224.239KB
Recall Quarterly Report #3, 2021-1
RCLQRT-20V292-8418.PDF 211.331KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V292&docType=RCL
“This site contains affiliate links for which OEMDTC may be compensated” |
- 🚘WARNING: Intended to be used on parked vehicles ONLY. Never drive with the BumperButler attached; using the BumperButler while driving may leave scratches on your car's exterior.
- 🚘Dimensions: 43 X 11 inches
- 🚘Easy installation with adjustable straps and hook to inside of your trunk. Folds into your trunk cargo area with ease when not in use. Loose dirt can be shaken out or vacuumed, and hard soiled areas can be hosed down with water and allowed to dry
- 🚘Patented, durable, and long-lasting rubber design; Fits most sedan vehicles. Strong security straps help deter theft and add extra sturdiness
- 🚘High-Intensity Safety Reflectors make the Bumper Butler stand out to vehicles parking behind you and helps make your vehicle noticeable in emergency situations
- High-quality material: High-quality soft and environmentally friendly material, reducing external impact, durable and scratch-resistant, flexible and flexible, and full of toughness.
- Excellent performance: Anti-scratch, abrasion resistance, anti-aging, groove anti-skid design, effectively prevent items from falling, and provide protection for scratches.
- Easy to install: After cleaning the location that needs to be installed, it can be installed privately without drilling or welding.
- Wide range of application: The newly upgraded 41x3.5 inches is suitable for most models such as SUVs and trucks. Please measure the size of the installation location before purchasing.
- Buy with confidence: If you have any questions, please contact us, we are always at your service.
- SUPER WIDE Bumper Protection Area; The Largest Bumper Protector!
- PREMIUM Grade Rubber Material
- Patented Stabilizer Bars Keep The BumperBully FLAT Against Your Bumper
- PREMIUM Grade Rubber Material (PVC FREE)
- Added protection against scuffs, nicks, scratches, and other damaging marks
- Textured surface provides slip resistance
- Quick and easy no-drill installation with the use of self-adhering 3M Tape
- Attaches directly to your rear bumper
- To ease concerns about fitment, use the size variations above to see images of our bumper protector on your vehicle
- Fits select 2020-2024 Toyota Highlander, 2020-2024 Toyota Highlander Hybrid Models. Please confirm fitment to your year, make, and model in Amazon Garage prior to purchase.
- Coverage: Rear Bumper, Color: Black
- Safeguard your rear bumper from scratches, paint chipping, and everyday wear and tear with the WeatherTech BumperTopper. Made from an impact-resistant hard plastic, it stands up to damage. When it’s time to trade your vehicle in, BumperTopper also helps cover small scuffs and blemishes to protect resale value.
- BumperTopper attaches directly to your bumper’s surface with Very High Bond adhesive strips. A Center Indication Mark makes installation quick, easy and accurate. This rear bumper cover hugs the profile of your vehicle’s bumper for custom-fit protection. BumperTopper is thin enough (3mm) to allow complete closure of your trunk or hatchback, yet tough enough to protect your vehicle.
- Made in USA!
- 🚘[PACKAGE INCLUDES] 1 BumperButler
- 🚘[DIMENSION] 43 x 11 inches
- 🚘[DURABLE AND MADE TO LAST] Our rubber design is not only durable and long-lasting, but it also fits most sedan vehicles. This means that you can trust our product to provide reliable protection for your vehicle for years to come, no matter what sedan you drive. So, if you're looking for a product that is both versatile and built to last, look no further than our rubber design.
- 🚘[EASY INSTALLATION] Installing our product is a breeze thanks to its adjustable straps and hook that attach to the inside of your trunk. This means that you can easily secure it in place and start using it right away. Plus, when you're not using it, it conveniently folds up and can be stored in your trunk cargo area without taking up too much space. So, whether you're using it frequently or just occasionally, our product is designed to be hassle-free and easy to use.
- 🚘[EASY TO CLEAN] Our product is durable and versatile. This means that you can rest assured that it will stay looking great even after repeated use. Additionally, it's easy to clean - loose dirt can be shaken out or vacuumed, and hard-soiled areas can be hosed down with water and allowed to dry. So, whether you're dealing with everyday dirt or a more serious mess, our product is designed to make cleaning a breeze.
- Universal Fit for All Cars: Ensure a flawless match with our TrexNYC bumper guard, universally designed to fit bumper guards for cars of all sizes. Experience the perfect blend of style and protection for your vehicle.
- High-Quality, Weather-Resistant Material: Crafted from premium, high-density foam, our bumper guard is an impenetrable shield against parking-related mishaps. Measuring just 1/4 inch thick, it's a sleek and durable solution to safeguard your car bumper.
- Effortless Installation, Instant Peace of Mind: Weighing only 1.5 lb., the lightweight design of our rear bumper car protector ensures easy installation, providing instant protection and peace of mind. No more worrying about dings, dents, or scratches while parking.
- Protection for Your Vehicle: Enjoy comprehensive coverage with our extra-wide (72-inch) bumper guard that wraps around the corners of your car. This ensures complete protection, making it an ideal choice for bumper guards for cars seeking maximum security.
- Secure and Adjustable Placement: Rest easy knowing your bumper guard is securely fastened with two Velcro straps attached to your trunk's carpet. Adjustable straps provide convenience, allowing you to customize the fit. Whether you opt for side straps or not. Our bumper guard protection is for your car bumper.
- Fits select 2016-2022 Honda Pilot Models. Please confirm fitment to your year, make, and model in Amazon ConfirmedFit prior to purchase.
- Coverage: Rear Bumper, Color: Black
- Safeguard your rear bumper from scratches, paint chipping, and everyday wear and tear with the WeatherTech BumperTopper. Made from an impact-resistant hard plastic, it stands up to damage. When it’s time to trade your vehicle in, BumperTopper also helps cover small scuffs and blemishes to protect resale value.
- BumperTopper attaches directly to your bumper’s surface with Very High Bond adhesive strips. A Center Indication Mark makes installation quick, easy and accurate. This rear bumper cover hugs the profile of your vehicle’s bumper for custom-fit protection. BumperTopper is thin enough (3mm) to allow complete closure of your trunk or hatchback, yet tough enough to protect your vehicle.
- Made in USA!
- Fits select 2017-2024 Mazda CX-5 Models. Please confirm fitment to your year, make, and model in Amazon ConfirmedFit prior to purchase.
- Coverage: Rear Bumper, Color: Black
- Safeguard your rear bumper from scratches, paint chipping, and everyday wear and tear with the WeatherTech BumperTopper. Made from an impact-resistant hard plastic, it stands up to damage. When it’s time to trade your vehicle in, BumperTopper also helps cover small scuffs and blemishes to protect resale value.
- BumperTopper attaches directly to your bumper’s surface with Very High Bond adhesive strips. A Center Indication Mark makes installation quick, easy and accurate. This rear bumper cover hugs the profile of your vehicle’s bumper for custom-fit protection. BumperTopper is thin enough (3mm) to allow complete closure of your trunk or hatchback, yet tough enough to protect your vehicle.
- Made in USA!
Last update on 2024-04-14 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.