VVK0009 – Insufficient Rear Impact Protection/FMVSS 224 – 2016-2020 Vac-Tron CS873GT, CV1273GT, LP1273XDT, CS1270GT, CS1273GT, CS870GT, & CS1273SGT Vacuum Excavator Trailers

“This site contains affiliate links for which OEMDTC may be compensated”

May 20, 2020 NHTSA CAMPAIGN NUMBER: 20V293000

Insufficient Rear Impact Protection/FMVSS 224

In the event of a rear impact crash, the other vehicle can travel under the rear of the vacuum excavator, increasing the risk of serious injury or death to someone in the other vehicle.

 

NHTSA Campaign Number: 20V293

Manufacturer Vac-Tron Equipment, LLC

Components STRUCTURE

Potential Number of Units Affected 105

 

Summary

Vac-Tron Equipment, LLC (Vac-Tron), a subsidiary of Vermeer Manufacturing Company (Vermeer), is recalling certain 2016-2020 CS873GT, CV1273GT, LP1273XDT, CS1270GT, CS1273GT, CS870GT, and CS1273SGT Vacuum Excavator trailers. The rear most extremity extends too far beyond the rear of the trailer frame, reducing impact protection. As such, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) Number 224, “Rear Impact Protection.”

 

Remedy

Vac-Tron will notify owners, and Vermeer dealers will install remedy kits provided by Vac-Tron, free of charge. The recall began July 14, 2020. Owners may contact Vac-Tron customer service at 1-888-822-8766. Vac-Tron’s number for this recall is VVK0009.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 


Vac-Tron Equipment, LLC

Trenchless
Okahumpka, FL  34762 USA

 

FIELD CAMPAIGN

SERVICE BULLETIN # SVV2020-011

DATE: 30 June 2020

 

CAMPAIGN TYPE: Mandatory-Product Safety
CAMPAIGN CATEGORY: Kit and Bulletin

 

MACHINE /

ATTACHMENT

MODEL (S) :

Serial Numbers
Included Excluded Kit Version
CSGT See attached listing on page 4 of this Bulletin for specific VIN and Serial/Unit numbers. N/A VVK01
CV1273SGT
CVGT
CVSGT
LP1273XDT

 

Subject:

PRODUCT SAFETY RECALL

FIRST NOTICE

 

Light Relocation, Reflector, Conspicuity Tape and Rear Extension Installation Kit (VVK00-0009)

 

Background:

INADEQUATE LIGHTING, REFLECTORS AND CONSPICUTITY TAPE

The lighting, side and rear reflectors and conspicuity tape do not meet US or Canada Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) governmental regulation 108 for the Unites States, Canada and Mexico. The trailers may not have an extended lower rear chassis, reducing rear impact protection and does not meet US or Canada Federal Motor Vehicle Standard (FMVSS/CMVSS) government regulation 223 for the United States, Canada and Mexico.

 

DEATH OR SERIOUS INJURY POSSIBLE

When towing or parking the vacuum excavator on public roadways, a crash may occur resulting in death or serious injury resulting from a driver(s) of other vehicle(s) not seeing the vacuum excavator at night or during limited sunlight and strike the vacuum excavator. To reduce the potential of this occurring, vehicle lights will be relocated, additional reflectors and conspicuity tape are being added.

In the event of a rear impact crash, the other vehicle may travel under the rear of the vacuum excavator, increasing the risk of serious injury or death to someone in the other vehicle or to the towing vehicle occupants.

Property or equipment damage may also occur.

 

Solution:

IMMEDIATE MACHINE MODIFICATIONS REQUIRED

VVK00-0009 has been created to provide the necessary parts and instructions to relocate the vehicle lights, add reflex reflectors, add conspicuity tape to the sides and rear, and add a rear extension. This kit must be installed as soon as possible.

Please be reminded that it is a violation of Federal law for you to sell or lease the machines covered by this notification until this recall has been performed on these machines. Substantial civil penalties apply to violations of this law.

 

DEALER PARTICIPATION
REVIEW REPORT, ORDER KITS, CONTACT CUSTOMERS

  1. Reports will be emailed during the week of June 30, 2020, to dealerships shown in our records which have units in their territory affected by this Alert. Please review the report for accuracy, including owner and/or address changes.

If the information contained in the report is NOT correct, please notify the Product Safety Department on or before July 13, 2020 at:

Telephone: 641-621-7060
Fax:  641-621-8562
Email: productsafety@vermeer.com

 

  1. Dealerships Order Kits by calling Vac-Tron at 888-822-8766.

Each dealership should determine the quantity of Kits to order initially depending upon the number of units that may be available for immediate upgrade. Do not order more Kits than needed for immediate installation.

 

  1. Contact your affected customer(s) to schedule a mutually acceptable time to upgrade their machine. Note: Letters will be sent to the customer(s) on or about July 14, 2020. Also refer to Owner Notification section below.

If you have any questions concerning the installation of VVK00-0008, please contact the Vac-Tron Service Department. Vermeer Corporation is assisting Vac-Tron with the administration of this campaign.

 

REIMBURSEMENT

Upon completion of each Kit installation, a campaign Warranty Claim must be submitted to the Vermeer Corporate Warranty Department for reimbursement of the parts cost and labor of the Kit.

 

This kit will reimburse 6 labor hours.

 

Note: Future notices to dealers and owners are dependent upon the receipt of Warranty Claim.

 

OWNER NOTIFICATION

Sample Letter: Included at the end of this Bulletin is a sample letter which will be sent by Vermeer Corporation directly to the Owners on or about July 14, 2020, via USPS certified/registered mail. Owner registrations indicate no translations are required for this campaign. The owner letter will be available in English only.

This owner notification/letter instructs the owner to contact their local dealership to arrange for a time to have the Kit installed. After receiving IK00-xxxx from the Parts Center, you must contact your affected customer(s) immediately and schedule a mutually acceptable time to upgrade their machine.

We regret any inconvenience these corrective measures may cause you. This required work is for safety of the safety of the towing vehicle driver and occupants as well as other traveling on public roadways or in the immediate are while being towed. We hope you agree the safety benefits surpass the inconvenience.

 

VAC-TRON EQUIPMENT, INC.

Attachment:
VVK00-0009 Kit Instructions

 



NHTSA SAFETY RECALL NUMBER 20V-290 and 20V-293

IMPORTANT SAFETY RECALL

First Notice

Light Relocation, Reflector, Conspicuity Tape and Rear Extension Installation Kit   (VVK00-009)

 

Sample Owner Letter

 

Model: «Model»

This notice applies to your vehicle,

Serial No: «VIN»

Unit No: «PART_SRL»

 

VIA USPS CERTIFIED/REGISTERED MAIL

July 14, 2020

Dear «MODEL» Owner:

This notice is sent to you in accordance with the requirements of the U.S. National Traffic and Motor Vehicle Safety Act.

Vermeer has decided that a defect, that relates to motor vehicle safety, exists in certain model year 2016-2020 Vermeer «MODEL».

 

INADEQUATE LIGHTING, REFLECTORS AND CONSPICUTITY TAPE

The lighting, side and rear reflectors and conspicuity tape do not meet US or Canada Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) governmental regulation 108 for the Unites States, Canada and Mexico.

The trailers may not have an extended lower rear chassis, reducing rear impact protection and does not meet US or Canada Federal Motor Vehicle Standard (FMVSS/CMVSS) government regulation 223 for the United States, Canada and Mexico.

 

DEATH OR SERIOUS INJURY POSSIBLE

When towing or parking the vacuum excavator on public roadways, a crash may occur resulting in death or serious injury resulting from a driver(s) of other vehicle(s) not seeing the vacuum excavator at night or during limited sunlight and strike the vacuum excavator. To reduce the potential of this occurring, vehicle lights will be relocated, additional reflectors and conspicuity tape are being added.

In the event of a rear impact crash, the other vehicle may travel under the rear of the vacuum excavator, increasing the risk of serious injury or death to someone in the other vehicle or to the towing vehicle occupants.

Property or equipment damage may also occur.

 

IMMEDIATE MACHINE MODIFICATIONS REQUIRED

VVK00-009 has been created to provide the necessary parts and instructions to relocate the vehicle lights, add reflex reflectors, add conspicuity tape to the sides and rear, and add a rear extension. This kit must be installed as soon as possible.

Please contact your authorized, independent Vermeer dealer immediately to arrange a mutually acceptable time and location to install VVK00-009 at no cost to you for labor or materials. The installation of this kit is estimated at 6 hours of labor.  If the Vermeer dealer travels to the unit to install the kit, costs may be incurred by the owner. You must have your machine upgraded for these safety features.

 

Contact your local Vermeer Dealer:  «Service_Dealer_Name»
«Serv_Dealer_Add1» «Serv_Dealer_Add2»
«Serv_Dealer_City» «Serv_Dealer_St» «Serv_Dealer_Zip»
«SERV_DEALER_COUNTRY» Telephone: «Serv_Dealer_Phone»

 

According to our records, you currently own a Vermeer «MODEL» vacuum excavator trailer. The Model and Serial Number of the «MODEL» is shown at the top right of this letter.  If you no longer own this unit, please notify the Product Safety Department at:

Toll Free: 800-829-0051, extension 7060
Telephone: 641-621-7060
E-mail: productsafety@vermeer.com

If possible, please provide the name and address of the new owner. Vermeer Corporation is  Vac-Tron with the administration of this campaign.

 

We regret any inconvenience these corrective measures may cause you. This required work is for safety of the safety of the towing vehicle driver and occupants as well as other traveling on public roadways or in the immediate are while being towed. We hope you agree the safety benefits surpass the inconvenience.

 

Very truly yours,

VAC-TRON EQUIPMENT, LLC

 

Federal regulations require that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten (10) days.

 

If the authorized dealer has failed or is unable to remedy the defect without charge and within a reasonable time, contact Vermeer Product Safety by email at productsafety@vermeer.com or by calling 800-829-0051 or 641-621-7060. You may also submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, D.C. 20590 or call the Vehicle Safety Hotline at 888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov

 


Vac-Tron Equipment, LLC

Trenchless
Okahumpka, FL 34762 USA

 

FIELD CAMPAIGN KIT VVK0000009

DATE: 30 June 2020

For Dealer Reference: Service Bulletin # SVV2020-011

Light Relocation, Reflector and Conspicuity Tape Installation Kit

CAMPAIGN TYPE: Mandatory-Product Safety
CAMPAIGN CATEGORY: Kit and Bulletin

 

MACHINE /

ATTACHMENT

MODEL (S) :

Serial Numbers
Included Excluded Kit Version
CSGT See attached listing on page 17 of this Kit Instructions for

specific VIN and Serial/Unit numbers.

N/A VVK01
CV1273SGT
CVGT
CVSGT
LP1273XDT

 

PURPOSE: INADEQUATE LIGHTING, REFLECTORS AND CONSPICUTITY TAPE

The lighting, side and rear reflectors and conspicuity tape do not meet US or Canada Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) governmental regulation 108 for the United States, Canada and Mexico. When towing or parking the vacuum excavator on public roadways, a crash may occur resulting in death or serious injury resulting from a driver(s) of other vehicle(s) not seeing the vacuum excavator at night or during limited sunlight and strike the vacuum excavator. To reduce the potential of this occurring, vehicle lights will be relocated, additional reflectors and conspicuity tape are being added.  Property or equipment damage may also occur.

 

Shutdown Procedure

STOPPING THE MACHINE

 

For your safety and the safety of others, follow shutdown procedure before working on the machine for any reason, including servicing, maintaining, cleaning, inspecting, unclogging or transporting machine, or as otherwise directed in Operator’s manual.

 

Step 1: Make sure end of vacuum hose is clear of all spoils, debris, and other materials.

 

Step 2: Push Throttle Control left several times to slow engine.  Idle engine five minutes to allow vacuum pump (with Reverse Flow Lever – Neutral) to cool down.  This helps to prevent the buildup of condensation.

 

Step 3: Turn Key Switch OFF to shut down engine.

 

Step 4: Drain Filter Housing.

 

PROCEDURE 1:

 

  1. Align the bracket with the edge of the curb side I-beam as shown below. Ref. 1, Fig 1.

 

  1. Mark the light bracket hole locations onto the I-beam and drill (2) Ø9/32” (7.15 mm) holes through the I-beam.

 

  1. Attach the marker light bracket with the supplied hardware. Ref. 1, 2, 3, and 4, Fig. 1.

 

 

  1. Connect one end of the 100” (2.54 m) length of dual core wire to the front side marker lamp using the butt connectors. 5 and 6, Fig. 1.

 

  1. Place loom over wires for protection. Ref. 8, Fig. 1.
  2. Run the wire through the cross member and inside of the I-Beam to connect with the front clearance marker lamp. Reference step 3, Procedure 2 for connecting the front side marker lamp and front clearance marker lamp.

 

  1. Use supplied zip ties to fasten wire harness to trailer frame.
  2. Complete all steps for the street side of the trailer.

 

PROCEDURE 2:

 

  1. Remove the curb side marker light from the platform gusset and disconnect the wires. Retain the marker light for future installation.

 

  1. Place the front clearance marker bracket on the gusset approximately 1-1/2” (3.81 cm) from the bottom as shown in Figure C. If the location of the antifreeze tank stand interferes with positioning the bracket properly, position the marker bracket just below the antifreeze tank stand as shown if Figure D.  Mark the bolt locations on the gusset and drill (2) Ø9/32” (Ø7.15 mm) holes. (Curb side shown). Ref. 1

 

  1. Use the 1 ft (30.48 cm) length of dual core conductor wire to reconnect the front clearance marker lamp and tie in with the 100” (2.54 m) length wire from the front side marker lamp. Use the 12-10 (yellow) and 16-14 (blue) heat seal butt connectors to connect all wires according to diagram below.

 

  1. Insert the front clearance marker lamp into the front clearance marker bracket as shown. Ref A, Fig. 2 for VVK01. Ref 2, Fig 2 for VVK02.  Refer to the illustration below for proper lamp orientation.
  2. Attach the front clearance marker bracket with the hardware Ref. 3, 4, and 5 Fig. 2.
  3. Loom all exposed wires. Ref. 8 Fig. 2.
  4. Repeat all steps to connect the front clearance marker lamp on the street side of the trailer.

 

PROCEDURE 3:

 

  1. Clean area where the conspicuity tape will be installed with light soap and water. Areas with damaged paint or heavy corrosion should be prepped, painted, and thoroughly dry before applying conspicuity tape.
  2. Refer to the illustration and install the conspicuity tape in the locations shown. Ref. 1 and 2, Fig. 3.
  3. Repeat for the opposite side of the trailer.

 

PROCEDURE 4:

 

  1. Remove the existing rear corner/side clearance marker lamp from the gusset and disconnect the wires. Retain the light for future installation.

 

  1. Place the rear corner/side clearance marker bracket on the support approximately 1-1/2” (3.81 cm) from the bottom as indicated in the illustration below. Mark the bolt locations on the support and drill (2) Ø9/32” (Ø7.15 mm) holes.
  2. Use the 1 ft (30.48 cm) length of dual core conductor wire to reconnect the rear corner/side clearance marker lamp using 16-14 butt connectors. Ref A, 7 and 8, Fig 4 for VVK01.

 

  1. Attach the rear corner/side clearance marker bracket to the fender support with the hardware as shown Ref. 3, 4, and 5 Fig. 4.
  2. Loom all exposed wires. Ref. 9 Fig. 4.
  3. Insert the rear corner/side clearance marker lamp into the bracket as shown Ref 1 and A, Fig. 4.
  4. Clean area where the rear side marker reflectors will be installed with light soap and water. Areas with damaged paint or heavy corrosion should be prepped, painted, and thoroughly dry before applying the reflectors as shown.

 

  1. Install the rear side marker reflector below the side marker bracket as shown.
  2. Repeat all steps for the opposite side of the trailer.

 

PROCEDURE 5:

 

  1. Clean area where the conspicuity tape will be installed with light soap and water. Areas with damaged paint or heavy corrosion should be prepped, painted, and thoroughly dry before applying the conspicuity tape.
  2. Refer to the illustration and install each of the white conspicuity tape on the debris tank door and water tanks as shown Ref 1, Fig. 5.

 

PROCEDURE 6:

 

  1. Ensure the debris tank is empty. Using suitable blocking, block debris tank to prevent shifting.  Debris tank weighs approximately 1,000 lb (455 kg).
  2. Remove the cotter pin on both sides.
  3. Push the headed pins out to be flush with the inner side of the tank hinges. Be careful not to push the pin through the hinge.

 

  1. Push the headed pins out to be flush with the inner side of the tank hinges. Be careful not to push the pin through the hinge.
  2. Use a suitable lifting device when installing the bumper. Bumper weight is approximately 120 lb (55 kg).
  3. Inspect the tank hinges connected to the bumper. Hinges with the single hole configuration shown must be replaced.  If the hinges have a 2-hole configuration, skip to step 9.

 

  1. Use a cutting torch to remove the (4) tank hinges from the bumper. Grind away residual slag.

 

  1. Remove all damaged paint down to bare metal. Repaint all affected areas.
  2. Install the bumper and align the bolt holes with the tank hinges.

 

  1. Push the headed pins back into position and replace the cotter pins on both sides.
  2. Install the hardware Ref. 3, 4, and 5 Figure 6. Tighten the bolts to 644 ft-lb (873 Nm).

 



 

FIGURE 1 Parts List
REF. NO. PART NO. DESCRIPTION VVK01 QTY.
1 B134-5749 FRONT SIDE MARKER LAMP BRACKET WITH REFLECTOR 2
2 P-1473 1/4-20 X 1 HEX HEAD BOLT 4
3 P-1472 1/4 ID FLAT WASHER 4
4 P-2782 1/4-20 NYLON LOCKNUT 4
5 P-1054 100” (2.54 m) LENGTH DUAL CORE CONDUCTOR WIRE 2
6 P-2369 16-14 HEAT SEAL BUTT CONNECTOR BLUE 4
7 P-1301 ZIP TIE 15
8 P-2762 1/2″ SPLIT WIRE LOOM, 100” (2.54 m) LENGTH 2

 

FIGURE 2 Parts List
REF. NO. PART NO. DESCRIPTION VVK01 QTY.
1 B134-5748 FRONT CLEARANCE MARKER LAMP BRACKET 2
A P-4190 FRONT CLEARANCE MARKER LAMP (EXISTING ON TRAILER) 2
3 P-1473 1/4-20 X 1 HEX HEAD BOLT 4
4 P-1472 1/4 ID FLAT WASHER 4
5 P-2782 1/4-20 NYLON LOCKNUT 4
6 P-1054 1’ (30.48 cm) LENGTH DUAL CORE CONDUCTOR WIRE 2
7 P-1611 12-10 HEAT SEAL BUTT CONNECTOR 4
8 P-2762 1/2″ SPLIT WIRE LOOM, 1’ (30.48 cm) LENGTH 2
9 P-2369 16-14 HEAT SEAL BUTT CONNECTOR BLUE 4

 

FIGURE 3 Parts List
REF. NO. PART NO. DESCRIPTION VVK01 QTY.
1 P-1426 2” (2.5 cm) WIDE, 101 ”(256.5 cm) LONG CONSPICUITY TAPE 2
2 P-1426 2” (2.54 cm) WIDE, 25” (63.5 cm) LONG CONSPICUITY TAPE 2

 

FIGURE 4 Parts List
REF. NO. PART NO. DESCRIPTION VVK01 QTY.
1 B134-5748 REAR CORNER/SIDE CLEARANCE MARKER LAMP BRACKET 2
A P-4189 REAR CORNER/SIDE CLEARANCE MARKER LAMP (EXISTING ON TRAILER) 2
2 P-4189 REAR CORNER/SIDE CLEARANCE MARKER LAMP 0
3 P-1473 1/4-20 X 1 HEX HEAD BOLT 4
4 P-1472 1/4 ID FLAT WASHER 4
5 P-2782 1/4-20 NYLON LOCKNUT 4
6 P-5730 REAR SIDE MARKER REFLECTOR 4
7 P-1054 1’ (30.48 cm) LENGTH DUAL CORE CONDUCTOR WIRE 2
8 P-2369 16-14 HEAT SEAL BUTT CONNECTOR BLUE 8
9 P-2762 1/2″ SPLIT WIRE LOOM, 1’ (30.48 cm) LENGTH 2

 

FIGURE 5 Parts List
REF. NO. PART NO. DESCRIPTION VVK01 QTY.
1 P-5783 WHITE CONSPICUITY TAPE 4

 

FIGURE 8 Parts List
REF. NO. PART NO. DESCRIPTION VVK01 QTY.
1 135500258 REAR EXTENSION 1
A SA-4471 HEADED PIN (EXISTING ON TRAILER) 2
3 135500218 1-8 X 6-1/2 HEX BOLT 2
4 P-3827 1 ID FLAT WASHER 4
5 P-2626 1-8 PREVAILING TORQUE NUT 2
6 135500216 TANK HINGE BRACKET 4

 


35 Affected Products

Vehicles

MAKE MODEL YEAR
VAC-TRON CS 1270 GT 2016-2020
VAC-TRON CS 1273 GT 2016-2020
VAC-TRON CS 870 GT 2016-2020
VAC-TRON CS 873 GT 2016-2020
VAC-TRON CV 1273 GT 2016-2020
VAC-TRON CV 1273 SGT 2016-2020
VAC-TRON LP 1273 XDT 2016-2020

 


9 Associated Documents

Non-Compliance Notice 573 Report

RCLRPT-20V293-3677.PDF 216.715KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [211.64 KB]

 


Recall Acknowledgement

RCAK-20V293-6235.pdf 245.457KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [239.70 KB]

 


Remedy Instructions and TSB

RCRIT-20V293-6692.pdf 2380.489KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.27 MB]

 


Miscellaneous Document- Before and After

RMISC-20V293-6518.pdf 609.92KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [595.62 KB]

 


Safety Bulletin

RCSB-20V293-9755.pdf 1199.269KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.14 MB]

 


Recall Quarterly Report #2, 2020-4

RCLQRT-20V293-6039.PDF 211.242KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.29 KB]

 


Recall Quarterly Report #1, 2020-3

RCLQRT-20V293-6000.PDF 211.138KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.19 KB]

 


Owner Notification Letter(Part 577)

RCONL-20V293-2999.pdf 223.687KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [218.44 KB]

 


Recall Quarterly Report #3, 2021-1

RCLQRT-20V293-7897.PDF 211.323KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.37 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V293&docType=RCL

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
SaleBestseller No. 1
FH Group Universal Fit Rear Bumper Guard Protection Bumperbutler for Cars, Suvs, Vans, and Trucks Black
  • 🚘WARNING: Intended to be used on parked vehicles ONLY. Never drive with the BumperButler attached; using the BumperButler while driving may leave scratches on your car's exterior.
  • 🚘Dimensions: 43 X 11 inches
  • 🚘Easy installation with adjustable straps and hook to inside of your trunk. Folds into your trunk cargo area with ease when not in use. Loose dirt can be shaken out or vacuumed, and hard soiled areas can be hosed down with water and allowed to dry
  • 🚘Patented, durable, and long-lasting rubber design; Fits most sedan vehicles. Strong security straps help deter theft and add extra sturdiness
  • 🚘High-Intensity Safety Reflectors make the Bumper Butler stand out to vehicles parking behind you and helps make your vehicle noticeable in emergency situations
Bestseller No. 3
SINGARO Car Rear Bumper Protector, 41inch x3.5inch Car/SUV Universal Rubber Anti-Scratch Trunk Exterior Accessories(Black)
  • High-quality material: High-quality soft and environmentally friendly material, reducing external impact, durable and scratch-resistant, flexible and flexible, and full of toughness.
  • Excellent performance: Anti-scratch, abrasion resistance, anti-aging, groove anti-skid design, effectively prevent items from falling, and provide protection for scratches.
  • Easy to install: After cleaning the location that needs to be installed, it can be installed privately without drilling or welding.
  • Wide range of application: The newly upgraded 41x3.5 inches is suitable for most models such as SUVs and trucks. Please measure the size of the installation location before purchasing.
  • Buy with confidence: If you have any questions, please contact us, we are always at your service.
Bestseller No. 4
BumperBully - The Ultimate Outdoor Rear Bumper Guard (Black Edition)
  • SUPER WIDE Bumper Protection Area; The Largest Bumper Protector!
  • PREMIUM Grade Rubber Material
  • Patented Stabilizer Bars Keep The BumperBully FLAT Against Your Bumper
  • PREMIUM Grade Rubber Material (PVC FREE)
Bestseller No. 5
TrexNYC Bumper Guard - Car Bumper Protector, Rear Bumper Guard - The Ultimate Bumper Protector for Car - Reliable Rear Car Bumper Protection
  • Universal Fit for All Cars: Ensure a flawless match with our TrexNYC bumper guard, universally designed to fit bumper guards for cars of all sizes. Experience the perfect blend of style and protection for your vehicle.
  • High-Quality, Weather-Resistant Material: Crafted from premium, high-density foam, our bumper guard is an impenetrable shield against parking-related mishaps. Measuring just 1/4 inch thick, it's a sleek and durable solution to safeguard your car bumper.
  • Effortless Installation, Instant Peace of Mind: Weighing only 1.5 lb., the lightweight design of our rear bumper car protector ensures easy installation, providing instant protection and peace of mind. No more worrying about dings, dents, or scratches while parking.
  • Protection for Your Vehicle: Enjoy comprehensive coverage with our extra-wide (72-inch) bumper guard that wraps around the corners of your car. This ensures complete protection, making it an ideal choice for bumper guards for cars seeking maximum security.
  • Secure and Adjustable Placement: Rest easy knowing your bumper guard is securely fastened with two Velcro straps attached to your trunk's carpet. Adjustable straps provide convenience, allowing you to customize the fit. Whether you opt for side straps or not. Our bumper guard protection is for your car bumper.
SaleBestseller No. 6
Rear Bumper Guard Protector for Car, Universal Black Rubber Scratch-Resistant Non-Slip Trunk Door Protector for Most Cars, Car Exterior Accessories
  • [High-quality Material] Our product is made of upgraded rubber material, which is durable and eco-friendly, features scratch-resistant, abrasion resistant, anti-aging, heat & cold resistant performance and flexible, upgraded quality extends service life.
  • [Multiple Use] Effectively prevent scratches and damages when loading and unloading luggages, tool box, groceries and more items in car trunk, also can be used to cover existing scratches and stains in the car surface, keep car looks new and clean.
  • [Easy to Install] Our protective strips come with adhesive backing, no need any extra tools. Clean the surface to make sure there's no oil, water or dirty stain first, tear off the tape on the back, put and press our rubber bumeper guard protector on the car surface. Easy and convenient to use and remove.
  • [Specification] Measuring 2.95*35.43". Practical to meet your need in daily life to protect car. Universal for most cars with rear guard, if you are not sure whether it is enough for your car, please measure accurately before ordering.
  • [ONE YEAR WARRANTY] We're always committed to provide our customer with quality product and the best after-sales service, your satisfaction is our first priority. Please feel free to let us know if you have any questions.
Bestseller No. 7
otoez Car Bumper Guard Foldable Truck Rear Bumper Protector Universal Trunk Mat SUV Cargo Liner Floor Mat Prevent Scratches While Unloading and Loading, 31.4 x 25.2 Inch
  • ✓ Universal Bumper Guards: This trunk bumper protector universal fits car, truck, sedan, SUV. It is a must-have accessory to any vehicle.
  • ✓ High Quality Material: Made of 600D oxford cloth and pearl cotton, soft, lightweight and wearable, will not scratch or hurt your bumper.
  • ✓ Protect Truck Cargo: Protect the rear bumper from scratch and damage when transporting or placing heavy objects, boxes, in the trunk. Keeping your trunk clean and organized.
  • ✓ Easy to Use: With 2 straps and buckles, this bumper guards can be hung on the trunk hook. Besides, the head has a Velcro, which can be pasted on the trunk pad and firmly fixed.
  • ✓ Foldable Trunk Bumper Protector: It is 31.4'' * 25.2'', and can be easily folded and stored at will. Pull down when you need it and folds up in your trunk when not in use.
SaleBestseller No. 8
Car Rear Bumper Guard, DIY Peel & Stick On Car Bumper Protector, Adhesive Bumper Protector for Cars, Tough Rubber Protective Strip Universal Fit, 6 x 62 inches - BumperX
  • Quality Bumper Guards for Cars - Protect your car from any “love taps” without ruining its looks with our rear bumper guard. It’s crafted from a formulated premium grade EDP rubber that is soft and elastic. Our bumper rubber guard is tough and built to last for years.
  • Suitable for the Outdoors - Designed to last, our car bumper guard uses a special 3M adhesive car bumper tape. It easily adheres to automotive clear coats, plastic, and metal. It’s also resistant to UV rays and harsh weather conditions.
  • Customizable Car Bumper Strip - Aiming for a better fit? You can easily trim this rear bumper protector to suit flat bumpers. It’s also lightweight, allowing you to handle and install it quickly. You can use it as a front bumper guard, too, with careful measurements and trimmings.
  • Preserves Your Vehicle - Say goodbye to constant repairs and long waiting hours in the shop with our car bumper protectors! Cover up dents and scratches or safeguard your vehicle with this auto bumper guard. It’ll act as your car’s second skin!
  • Sleek Universal Design - No more blemishes or repaints—enhance your car’s appearance and appeal when you stick this car rubber bumper guard. BumperX’s rear bumper cover comes in black. It can cover any tiny flaws and complement any car color.
Bestseller No. 9
FH Group Universal Fit BumperButler® Rubber Mat for Rear of Vehicle Universal Fit for Trucks, SUVs, and Vans Black Automotize Accessories
  • 🚘[PACKAGE INCLUDES] 1 BumperButler
  • 🚘[DIMENSION] 43 x 11 inches
  • 🚘[DURABLE AND MADE TO LAST] Our rubber design is not only durable and long-lasting, but it also fits most sedan vehicles. This means that you can trust our product to provide reliable protection for your vehicle for years to come, no matter what sedan you drive. So, if you're looking for a product that is both versatile and built to last, look no further than our rubber design.
  • 🚘[EASY INSTALLATION] Installing our product is a breeze thanks to its adjustable straps and hook that attach to the inside of your trunk. This means that you can easily secure it in place and start using it right away. Plus, when you're not using it, it conveniently folds up and can be stored in your trunk cargo area without taking up too much space. So, whether you're using it frequently or just occasionally, our product is designed to be hassle-free and easy to use.
  • 🚘[EASY TO CLEAN] Our product is durable and versatile. This means that you can rest assured that it will stay looking great even after repeated use. Additionally, it's easy to clean - loose dirt can be shaken out or vacuumed, and hard-soiled areas can be hosed down with water and allowed to dry. So, whether you're dealing with everyday dirt or a more serious mess, our product is designed to make cleaning a breeze.
Bestseller No. 10
Ziciner Car Rear Bumper Protector Guard, Anti-Scratch Carbon Fiber Trunk Door Sill Protection Strip Sticker, Universal Vehicle Trim Cover Accessories for Car, Truck, SUV, Van (35.4×3.75 in, Black)
  • 【High-Quality Materials】: Our car rear bumper protection strip is made of high quality PVC material, which is resistant to high temperature, friction and corrosion, and has good hardness and toughness. It can protect your car door panel from wear and tear, will not scratch the original car paint, even if it is frequently scraped, it will not be easily damaged.
  • 【Anti-scratch/Waterpoor】: This product can effectively protect the car trunk door sill, it can prevent nasty scratches, wear and tear, and provide protection during the process of items, luggage up and down and in and out to keep the vehicle surface paint perfect. It is also waterproof, so you don't have to be afraid of getting wet when it rains, just wipe it off.
  • 【Easy Installation】: Before installation, wipe the trunk door sill clean and make sure the surface is clean and dry. Tear off the adhesive backing film, grasp the location where it needs to be pasted, stick the protection strip flat on its surface and press it evenly for a few seconds to make sure it is tight. The installation process does not require much effort and can be easily completed in a few minutes.
  • 【Widely Application】: This product is cut for the original version and is universally suitable for most cars, trucks, pickups or SUVs. After many tests and uses on real cars, our protection strips will never fail to fit in any way. We have 2 sizes for you to choose from, we suggest you measure the size of the installation location before you buy.
  • 【Decorative】: This car door sill sticker is not only protective, but also decorative. It has two colors for you to choose, please choose the color that suits your car to make it more personalized and sporty fashion.

Last update on 2024-03-15 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...