| “This site contains affiliate links for which OEMDTC may be compensated” |
August 21, 2019 NHTSA CAMPAIGN NUMBER: 19V613000
Engine Harness May Chafe and Cause Engine Stall
Damaged wires may cause a sudden reduction in engine power or an engine stall, increasing the risk of a crash.
NHTSA Campaign Number: 19V613
Manufacturer McLaren Automotive Incorporated
Components ELECTRICAL SYSTEM, ENGINE
Potential Number of Units Affected 129
Summary
McLaren Automotive Incorporated (McLaren) is recalling certain 2018-2019 Senna vehicles. The engine harness may contact a metal link pipe heat shield, chafing the harness over time, potentially damaging the wires.
Remedy
McLaren will notify owners, and dealers will reroute the engine harness, free of charge. The recall began October 18, 2019. Owners may contact McLaren’s Client Services department at (855) 202-8815 or clientservicesna@mclaren.com.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Urgent – Immediate Action Required
McLaren Senna – Engine Wiring
Harness Rework
| Bulletin type: | Safety Recall Campaign |
| Reference number: | SRC 15 F 002 |
| Campaign reference: | 04S |
| Attention: | Retailer General Managers, Retailer Aftersales Managers, Retailer Service Managers, Retailer Service Advisors, etailer Technicians, Retailer Parts Manager |
| Affected vehicles: | McLaren Senna |
| Situation: | Potential for contact between the engine wiring harness and neighbouring engine exhaust heat shield |
| Procedure: | To action affected vehicles on next Retailer visit.
Please refer to the information outlined in this document to replace an existing engine wiring harness cable tie |
| Date: | 4th August 2019 |
Urgent Safety Recall Campaign – McLaren Senna – Engine wiring harness:
- Retailers must contact customers and make service appointments as soon as reasonably practical.
- Repairs are to be performed by any McLaren Authorised Retailer regardless of where the vehicle was purchased.
For more details, please read the bulletin below.
This Safety Recall Campaign will cover:
1. Immediate Action Required
2. Overview
3. Procedure
4. Parts Information
5. Warranty Information
6. Affected vehicles
1. Immediate Action Required
Retailers must contact customers and make service appointments as soon as reasonably practical.
Repairs are to be performed by any McLaren Authorised Retailer regardless of where the vehicle was purchased. Retailers must not refuse to repair a vehicle due to the fact that it was not purchased from their location.
2. Overview
McLaren Automotive has identified through continuous product quality monitoring, that a number of McLaren Senna vehicles may have a concern whereby the engine wiring harness can contact the neighbouring engine exhaust
heatshield. This could result in damage to the insulation sleeve on the engine wiring harness.
If the wires are damaged, there are a number of potential consequences: (1) the car could enter idle limp mode (significant engine power reduction); (2) there could be a torque limitation (slight engine power reduction); (3
) the engine could stall; or (4) if the engine is not turned off despite the existence of several warnings to the driver, unburnt fuel in the catalyst could lead to increased temperature of the catalyst, resulting in overheating. This could eventually lead to a rupture of the exhaust system, which would allow exhaust gasses to escape. Depending on the location of such a rupture, there could be damage to the vehicle.
3. Procedure
To carry out the required rework, replacement of an existing engine wiring harness cable tie is required. Document
SRC 15 F 002 WI (attached with this bulletin), contains the relevant work instruction and care points to ensure the
required repair is carried out to bring the vehicle up to the current manufacturing standard.
In cases where contact between the engine wiring harness and engine exhaust heatshield is present and wear to the engine harness insulation sleeve is present, please submit a Technical Request including pictures to the Technical Support team for further advice.
4. Parts Information
The below part is required to action this repair and can be ordered in the usual way via Unidial.
| Part Number | Part Description | Quantity Required |
| 00RL023 (Unit of Purchase is 10) | Cable tie – High temp | 1 |
5. Warranty Information
| Description | Resolution Code | Repair Time |
| McLaren Senna – Engine Wiring Harness Rework | CPCPC504A11A9901 | 1.85 hours |
6. Affected vehicles
All Model Year 2018 and 2019 McLaren Senna vehicles manufactured prior to 2nd August 2019 are affected by this issue.
Your Regional Aftersales Manager will contact you with a list of affected vehicles.
If you have any questions, please speak to your Regional Aftersales Manager.
IT IS A VIOLATION OF FEDERAL LAW TO SELL OR DELIVER A NEW VEHICLE COVERED BY THIS NOTIFICATION UNTIL THE DEFECT IS REMEDIED.
Best regards,
Urgent – Immediate Action Required
McLaren Senna – Engine Wiring Harness Rework
| Bulletin type: | Safety Recall Campaign |
|---|---|
| Reference number: | SRC 15 F 002 |
| Campaign reference: | 04S |
| Attention: | Retailer General Managers, Retailer Aftersales Managers, Retailer Service Managers, Retailer Service Advisors, Retailer Technicians, Retailer Parts Manager |
| Affected vehicles: | McLaren Senna |
| Situation: | Potential for contact between the engine wiring harness and neighbouring engine exhaust heat shield |
| Procedure: | To action affected vehicles on next Retailer visit. Please refer to the information outlined in this document to replace an existing engine wiring harness cable tie |
| Date: | 4th August 2019 |
Urgent Safety Recall Campaign – McLaren Senna – Engine harness:
- Retailers must contact customers and make service appointments as soon as reasonably practical
- Repairs are to be performed by any McLaren Authorized Retailer regardless of where the vehicle was purchased
For more details, please read the bulletin below.
This Safety Recall Campaign will cover:
1. Immediate Action Required
2. Overview
3. Procedure
4. Parts Information
5. Warranty Information
6. Affected vehicles
1. Immediate Action Required
Retailers must contact customers and make service appointments as soon as reasonably practical.
Repairs are to be performed by any McLaren Authorised Retailer regardless of where the vehicle was purchased. Retailers must not refuse to repair a vehicle due to the fact that it was not purchased from their location.
2. Overview
McLaren Automotive has identified through continuous product quality monitoring, that a number of McLaren Senna vehicles may have a concern whereby the engine wiring harness can contact the neighbouring engine exhaust heatshield. This could result in damage to the insulation sleeve on the engine wiring harness.
If the wires are damaged, there are a number of potential consequences: (1) the car could enter idle limp mode (significant engine power reduction); (2) there could be a torque limitation (slight engine power reduction); (3) the engine could stall; or (4) if the engine is not turned off despite the existence of several warnings to the driver, unburnt fuel in the catalyst could lead to increased temperature of the catalyst, resulting in overheating. This could eventually lead to a rupture of the exhaust system, which would allow exhaust gasses to escape. Depending on the location of such a rupture, there could be damage to the vehicle.
3. Procedure
To carry out the required rework, replacement of an existing engine wiring harness cable tie is required. Document SRC 15 F 002 WI (attached with this bulletin), contains the relevant work instruction and care points to ensure the required repair is carried out to bring the vehicle up to the current manufacturing standard.
In cases where contact between the engine wiring harness and engine exhaust heatshield is present and wear to the engine harness insulation sleeve is present please submit a Technical Request including pictures to the Technical Support team for further advice.
4. Parts Information
The below part is required to action this repair and can be ordered in the usual way via Unidial.
| Part Number | Part Description | Quantity Required |
| 00RL023 (Unit of Purchase is 10) | Cable tie – High temp | 1 |
5. Warranty Information
| Description | Resolution Code | Repair Time |
| McLaren Senna – Engine Wiring Harness Rework | CPCPC504A11A9901 | 1.85 hours |
6. Affected vehicles
All Model Year 2018 and 2019 McLaren Senna vehicles manufactured prior to 2nd August 2019 are affected by this issue.
Your Regional Aftersales Manager will contact you with a list of affected vehicles. If you have any questions, please speak to your Regional Aftersales Manager.
IT IS A VIOLATION OF FEDERAL LAW TO SELL OR DELIVER A NEW VEHICLE COVERED BY THIS NOTIFICATION UNTIL THE DEFECT IS REMEDIED.
Best regards,
David Bodily
Head of Service Operations
Craig Danns
Technical Case Manager
The information contained in McLaren bulletins is for internal use only by McLaren Authorised Retailers and must not be published on external websites or social media forums etc.
Part numbers listed in McLaren bulletins are for reference only. Always check with the parts department to verify the latest part numbers.
SRC 15 F 002 WI
McLaren Senna – Engine Wiring Harness Rework Instructions
The total labour time is 1.85 hours.
Complete the pre-works that follows:
| Instruction Number | Instruction Name |
|---|---|
| EA-RM-01A001-00-001 | Secure/lift Vehicle on platform |
| EA-RM-04B005-01-001 | Remove/Install Wheel – Rear |
| EA-RM-02A051-03-002 | Remove/Install Panel – Bodyside access |
| EA-RM-02A053-03-001 | Remove/Install Panel- Rear wing |
| EA-RM-0ZA051-08-001 | Remove/Install Panel – Engine cover |
| EA-RM-0ZA051-03-005 | Remove/Install Panel – HTR Gurney |
| EA-RM-0ZA051-07-002 | Remove/Install Panel- Rear deck |
| EA-RM-03A071-10-002 | Remove/Install Extension – Rear bumper |
| EA-RM-0ZA051-03-001 | Remove/Install Bodyside – Upper |
The below parts are required:
| Part Number | Part Description | Quantity |
|---|---|---|
| 00RL023 | Cable tie – High temp | 1 |
RISK OF DAMAGE: Be careful with aesily damaged and trim
Care Point: Use protective covers to help prevent damage to paintwork
Care Point: If you see damage to the wiring harness, raise a technical request
1. Remove the bolt (1) 8 Nm and remove the airguide (2).
Care Point: Do not cause damage to the harness in the step that follows
2. Carefully cut and remove the cable tie (3) from the harness (4).
Care Point: The clip (5) must be used again in the subsequent steps
3. Turn the clip (5) to remove it from the cylinder head (6).
4. Cut the used cable tie from the clip as shown (7).
5. Assemble the new cable tie (8) – 00RL023 to the used clip (9).
6. Install new cable tie assembly into hole (10).
7. Make sure the gap between the cable tie (11) and the end of the chloroplast tape (12) is 10 -15mm.
8. Tighten the cable tie (11).
9. Make sure there is a minimum of 10mm of clearance between the harness (13) and the link pipe (14).
10. Install the components in the reverse order.
IMPORTANT SAFETY RECALL NOTICE
NHTSA Recall No. 19V-613
October 18, 2019
This important safety recall notice applies to your vehicle with the following Vehicle Identification Number (“VIN”):
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. McLaren Automotive Incorporated (“McLaren”) has decided that a defect that relates to motor vehicle safety exists in certain Model Year 2018-2019 McLaren Senna vehicles. According to our records, you are the owner of one of those vehicles.
WHAT IS THE ISSUE?
McLaren has determined that a branch of the Senna’s engine wiring harness can potentially come into contact with a metal link pipe heatshield. If there is contact, there may over time be chafing of the engine harness. If this chafing breaches the harness heatshield wrap and the harness outer sleeving, it could lead to damage to the wires contained within the engine harness bundle. If the wires are damaged, there are a number of potential consequences: (1) the car could enter idle limp mode (significant engine power reduction); (2) there could be a torque limitation (slight engine power reduction); and (3) the engine could stall, which could lead to a risk if a crash. There will be several warnings prior to any stall, including a dashboard warning light, a dashboard warning message, an audio alert signal, and a change in the vehicle’s driving characteristics.
In addition, if the engine is not turned off following these warnings, unburnt fuel in the catalyst could lead to increased temperature of the catalyst, resulting in overheating. This could eventually lead to a rupture of the exhaust system, which would allow exhaust gasses to escape. Depending on the location of such a rupture, there could be damage to the vehicle, increasing the risk of a crash.
WHAT MCLAREN WILL DO
To remedy this problem, your McLaren dealer will re-route the wiring harness to assure that it will not come into contact with the heatshield. This will be performed at no cost to you.
WHAT YOU SHOULD DO
At your earliest convenience, please call your McLaren dealer to schedule an appointment to have the remedy performed. We estimate that the procedure will take less than two (2) hours to complete.
OTHER IMPORTANT INFORMATION
If you no longer own the vehicle identified above, please contact McLaren’s Client Services department at (855) 202-8815 or clientservicesna@mclaren.com. If possible, please provide us with the name and address of the current owner so we may contact him or her regarding this recall.
If you have any questions or require further assistance, please contact McLaren’s Client Services department at (855) 202-8815 or clientservkesna@mclaren.aom.
If you believe that McLaren has failed or is unable to remedy the defect without charge within a reasonable time, please contact us at the number shown above. You may also contact the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE, Washington, DC 20590; or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153);, or go to https://www.safercar.gov.
If you have leased any of the above-referenced vehicles to another person, Federal regulations require you to send a copy of this notice to the lessee by first-class mail within ten days of your receipt of this notice.
Thank you for your prompt attention to this matter. We sincerely regret any inconvenience that this condition may cause you. Your safety is our highest priority.
Sincerely,
VP Fixed Operations
2 Affected Products
Vehicle
| MAKE | MODEL | YEAR |
| MCLAREN | SENNA | 2018-2019 |
12 Associated Documents
Recall Quarterly Report #2, 2020-1
RCLQRT-19V613-8129.PDF 211.245KB
Loading...
Reload document 
Open in new tab
Defect Notice 573 Report
RCLRPT-19V613-9220.PDF 216.339KB
Loading...
Manufacturer Notices(to Dealers, etc.) Urgent – Immediate Action Required McLaren Senna – Potential for contact between the engine wiring harness and neighboring engine exhaust heat shield.
RCMN-19V613-4056.pdf 595.328KB
Loading...
Recall Acknowledgement
RCAK-19V613-1304.pdf 245.433KB
Loading...
Recall 573 Report – AMENDMENT 1
RCLRPT-19V613-2991.PDF 216.578KB
Loading...
Recall Quarterly Report #1, 2019-4
RCLQRT-19V613-5516.PDF 211.146KB
Loading...
Manufacturer Notices(to Dealers,etc)- SCB 15 F 001 McLaren Senna – Engine Wiring Harness Rework
RCMN-19V613-3651.pdf 476.285KB
Loading...
Recall 573 Report – Amendment 3
RCLRPT-19V613-9398.PDF 216.601KB
Loading...
Recall 573 Report – Amendment 2
RCLRPT-19V613-4563.PDF 216.583KB
Loading...
Remedy Instructions and TSB
RCRIT-19V613-1681.pdf 532.906KB
Loading...
ISSUED Owner Notification Letter(Part 577)
RCONL-19V613-6480.pdf 76.879KB
Loading...
Recall Quarterly Report #3, 2020-2
RCLQRT-19V613-2753.PDF 211.329KB
Loading...
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V613&docType=RCL
| “This site contains affiliate links for which OEMDTC may be compensated” |
- FEATURES - Metal zip ties made of 304 stainless steel. These heavy duty zip ties are 4x stronger than regular plastic zip ties. These stainless steel zip ties mean they are High temperature resistant, Cold resistant, Rust and Corrosion resistant. Unlike traditional plastic zip ties, these heavy duty metal ties won't break down by uv light in the sun like normal plastic zip ties.
- HEAVY DUTY - These stainless steel zip ties can support weight up to 90KG (198lb) which is 4x more than traditional plastic zip ties, and they can support temperatures up to 932 F.
- EASY TO USE - These self locking zip ties only need a set of needle nose plier to tighten and a diagonal plier or tin snips to cut the excess zip ties.
- UNIVERSAL APPLICATION - These stainless zip ties are perfect for outdoors, fence, gardens, farms, pipes, roofs, basements, auto application such as exhaust wraps, and more.
- Package Includes: ①stainless steel cable tie gun ②100 pcs 4.6 x 270mm Stainless steel cable tie ③Tool storage bag ④Industrial Metal Scissors ⑤Industrial gloves ⑥Metal Cable Tie Remover ⑦User Manual.
- Steel Cable zip tie Feature: The upgraded 304 stainless steel Metal zip ties max supporting weight is 198 lbs.High temperature and oxidation resistant, suitable for outdoor use.
- Tie Gun Cutting Range: Zip tie gun is very ideal for tensioning and cutting off stainless steel cable ties with width from 4.5mm to 12 mm, easily and cleanly without rough edges, will greatly improve your efficiency of work.
- Multiple Usage Metal Shears: Ideal for cutting aluminum,sheet metal,leather,floor covering,card board and plastic.
- Widely Applications: Stainless steel zip ties are extremely reliable, whether you're working on a building or rewiring project, you can fasten wires and components securely in place with metal zip ties. Metal ties is suitable for cable routing, exhaust/header heat wrap, electronic engineering, automobile, home improvement, outdoor fence repair etc.
- 【inch Size】:11.8” x 0.18" x 0.01" inch【mm Size】: 300 x 4.6 x 0.25mm(length x width x thickness)
- You can return for free if any quality issue! Because the tensile force of the cable ties is affected by the width, in the same width (4.6mm/0.18"inch), our tensile force is very large, reaching 250LB, using real materials, with strict quality supervision, we are very confident in our products. Please use it in the correct way and choose the correct length
- 【Material】: 304 stainless steel 【Package】:100 pcs 【Tension Strength】: 1100N/110kg/250pounds 【This is 304 material, can be used in general occasions. but if you want to use it in harsh occasions such as oceans and ships, please choose 316 material. 】
- 【Work Temperature】: -80 to 538 Celsius/-120℉~+1000℉ 【colour】: silver
- 【characteristic】：Used For Automotive Application Such As computer, ship cable， Exhaust Heat Wrap Binding，fence Repair, Etc.Don't Worry About Heat And Corrosion. Perfect For Outdoor Applications.Outstanding chemical resistance， Antimagnetic，Non-burning，Easy fitting Anti-corrosive.No Special Tools Required. just Need A Needle Nose Plier To Tighten And A Diagonal Plier Or Tin Snips To Cut it
- 【FEATURES】Metal Heavy duty 304 Stainless steel Zip Ties high temperature resistance, cold resistance, rust and corrosion resistance,Stainless steel Cable Ties is anti-oxidation, anti-ultraviolet, easy to operate, sturdy and Durable
- 【PHYSICAL PROPERTIES】304 stainless steel Our Metal zip ties max supporting weight is 198 lbs Operation Temperature -170℉~+1000℉ Max bundle diameter is 90mm 3.5inch
- 【EASY TO USE】Self-locking design Metal zip ties only need to be tightened with sharp-nosed pliers and the excess can be cut off with diagonal pliers or tin scissors, which allows you to complete the project efficiently
- 【SIZE QUANTITY】 11.8" x 0.18" x 0.01"/300mm x 4.6mm x 0.25mm (L*W*T) 100 PCS
- 【MULTIPLE USAGE】 This multifunctional cable zip ties are widely used in machinery, vehicles, gardens, farms, cables, pipes, roofs, basements as well as Outdoor binding perfect for use in harsh outdoor environments as well
- 【FEATURES】Metal Zip Ties black epoxy coating process, high temperature resistance, cold resistance, rust and corrosion resistance,Stainless steel Cable Ties is anti-oxidation, anti-ultraviolet, easy to operate, sturdy and Durable
- 【PHYSICAL PROPERTIES】304 stainless steel epoxy coating Our Metal zip ties max supporting weight is 198 lbs Operation Temperature -170℉~+500℉ Max bundle diameter is 90mm 3.5inch
- 【EASY TO USE】Self-locking design Metal zip ties only need to be tightened with sharp-nosed pliers and the excess can be cut off with diagonal pliers or tin scissors, which allows you to complete the project efficiently.
- 【SIZE QUANTITY】 300mm x 4.6mm x 0.25mm/ 11.8" x 0.18" x 0.01" (L*W*T) 100 PCS
- 【MULTIPLE USAGE】 This multifunctional cable zip ties are widely used in machinery, vehicles, gardens, farms, cables, pipes, roofs, basements as well as Outdoor binding perfect for use in harsh outdoor environments as well
- [Durable Metal Cable Tie Tool] To fasten and automatic cut ties with adjustable bunding pressure, cut stainless steel cable ties cleanly and without sharp edges.
- [Versatility] This versatile cable tensioning and cutting tool works with any length of cable tie wrap, and supports cable ties with a width of up to 0.47 in (12 mm) and a thickness of up to 0.01 in (0.3 mm).
- [Easy to Use] The fastening cable tie tool is small and exquisite, convenient and easy to use, suitable for self-locking, stepped and other cable ties, and can be cut without tightening.
- [Ergonomic Design] TPR handles and updated trigger reduces stress, fatigue and risk of injury from long term use.
- [Premium Quality] SKD11 steel blade and TPR handle,the characteristics of high hardness, high wear resistance, high slip resistance.It's durable
- [Premium Stainless Steel Cable Zip] Made of all 304 material, the stainless steel cable tie comes with excellent acid and alkali resistance, abrasion resistance, and anti-aging.
- [Flexible and Strong Bearing Capacity] These cable ties are made with a special flexible process, which is flexible and convenient for strapping. The zip ties heavy duty is high in strength and provides a maximum bearing capacity of 270 pounds.
- [Size and Design] Advanced cold rolling technology makes the product more compact. The product is 19.7 inches long, 0.18 inches wide, 0.01 inches thick, and the maximum bundle diameter is 4.02 inches.
- [High and Low Temperature Resistance] The cable ties can be used from -76°F to 752°F, which is more practical than ordinary traditional nylon cable ties.
- [Widely Used] It is manufactured with stainless steel substrate and sprayed plastic surface treatment, which is stylish and beautiful, widely used in transportation, computer, electronic engineering, automobile, home maintenance, etc.
- Durable Metal Cable Tie Tool : This portable pocket sized cable tie installation gun quickly and easily installs 316SS stainless steel cable ties.
- Easy to use: With a one-squeeze mechanism, the metal zip tie tightener adjusts the cable tie tension to perfectly suite your cable bundle, and trims excess metal from the cable tie in one motion.
- Versatility: This versatile cable tensioning and cutting tool works with any length of cable tie wrap, and supports widths up to 0.47in (12mm)
- Multifunction: This versatile cable tensioning and cutting tool works with any length of cable tie wrap, and supports widths up to 0.47inch, ensuring it can support a variety of cable ties, depending upon your application. Ideal for exhaust / header heat wrap, CV Joint rubber boot on motorcycle or automotive.
- Ergonomic design: TPR handleS and updated trigger reduces stress, fatigue and risk of injury from long term use.
- Quality Material: these metal zip ties are made of quality 304 stainless steel material, resistant to high temperature, cold, rust, corrosion and are suitable for outdoor applications
- Good Performance: the tensile strength of the stainless steel zip ties is 220 pounds (100Kg), and the operating temperature is from -170 degrees Fahrenheit to +1000 degrees Fahrenheit, very suitable for use in harsh outdoor environment
- Simple Operation: metal ties are as easy to use as plastic ties, and have self locking function; You can use pointed nose pliers to tighten the metal zip ties and diagonal pliers or tin scissors to cut off the excess part, so as to complete the project quickly
- Multifunctional: stainless steel cable ties provide a good solution for your long term work of fixing objects; They are ideal for your machinery, vehicles, farms, gardens, cables, pipes, roofs and basements, and are applied by ships, mine, power and oil companies worldwide
- Wide Use: metal heavy duty 304 stainless steel zip ties are suitable for binding cables and pipes, refitting automobile exhaust pipe, fixing chain link fence, wire fencing, privacy protection screen fence and fence post, and building pet cages and chicken coops; It is also a good choice to replace plastic ties and aluminum ties
- ☀ To fasten and automatic cut ties with adjustable bunding pressure.
- ☀ For cable ties thickness up to 0.3mm.width up to 12mm steel plate.
- ☀ Cut stainless steel cable ties, clean and without sharp edges.
- ☀ Durable cable tie 2x 100pcs, 4.6 x 300mm.
- ☀ Light weight and easy to carry.
Last update on 2024-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.