NHTSA ID Number: 10092539
Manufacturer Communication Number: RMI
TSB/Document Date: 2017-02-22
Summary
REGISTRATION MANUAL FOR IMMOBILIZER
system registration".)
Engine ECM registration
Items to be prepared
1. One registered key
2. Keys you want to register
Immobilizer system registration
Application
Perform when:
1. Additional keys are registered
2. Immobilizer CM is replaced
Mode name
1. Explanation of the SSM III registration mode
Caution:
When replacing the parts, always use a new one. Used parts cannot be registered.
If all the keys are lost, for protection against vehicle theft you must contact your Subaru service representative.
8-6 Immobilizer system (when Immobilizer CU (U.K./CANADA)) : Correspondence table at the time of
parts lost or failure
S1001BE.fm
E type
REGISTRATION MANUAL FOR IMMOBILIZER
125 ページ
２０１４年４月３０日
水曜日
午後２時９分
Vehicle-id:
SIE-id::
Å`
Error screen
125
Trouble mode
Action to be taken
When multiple attempts of registration did not solve the problem,
replace the immobilizer CM.
Perform the diagnosis for LAN system.
Immobilizer CM malfunction
CAN communication failure between Subaru Select Monitor and
immobilizer CM
NG Registration was not
successfully.
Transponder failure
Antenna failure
NG Abnormal Termination
NG Transponder communication
failure.
NG Immobilizer antenna failure.
→ "Initializing communication..."
7
—
Perform the diagnosis for LAN system.
•NG key
•Unregistered key
IGN-OFF performed during registration mode
CAN communication failure between Subaru
Select Monitor and
immobilizer CM
NG Transponder collation failure.
NG Performed conditions not
established.
NG BIU-SSM Communication
Prepare the registered key.
Check DTC and perform the diagnosis.
Check DTC and perform the diagnosis.
Check the data monitor. → Check the communication line.
Check version of Subaru Select Monitor.
Replace the immobilizer CM.
•Subaru Select Monitor malfunction
•Immobilizer CM malfunction
Execute "Immobilizer system registration" to register the key.
IGN line of immobilizer CM not detected
Immobilizer CM unregistered
Registered number = 0
Cannot confirm ignition ON.
"Engine ECU registration" start
→ "Turn ON the ignition switch."
Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)
5
NG EGI-SSM Communication
(Communication line judgment)
Communication failure between Subaru Select Monitor and ECM
Check DTC and perform the diagnosis.
Prepare the registered key.
•NG key
•Unregistered key
NG Transponder collation failure.
NG BIU-SSM Communication
Perform re-registration.
IGN-OFF performed during registration mode
Check DTC and perform the diagnosis.
NG Performed conditions not
established.
Check DTC and perform the diagnosis.
Antenna failure
Immobilizer CM failure
NG Non-volatile memory failure.
Check DTC and perform the diagnosis.
Transponder failure
NG Transponder communication
failure.
NG Immobilizer antenna failure.
Check version of Subaru Select Monitor.
Replace the immobilizer CM.
Check version of Subaru Select Monitor.
Replace the immobilizer CM.
•Subaru Select Monitor malfunction
•Immobilizer CM malfunction
NG Abnormal Termination
NG Cannot judge register mode (new
Immobilizer CM malfunction
or add)
Check the data monitor. Check the communication line.
IGN line of immobilizer CM not detected
Perform the diagnosis for LAN system.
Cannot confirm ignition ON.
CAN communication failure between Subaru Select Monitor and
immobilizer CM
•CAN communication failure between Subaru Select Monitor and
immobilizer CM
•CAN communication failure between Subaru Select Monitor and Perform the diagnosis for LAN system.
body integrated unit
6
4
→ "Initializing communication..."
3
→ "EGI initialization / During
registration..."
"Immobilizer system registration"
start
→ "Turn ON the ignition switch."
Select "Immobilizer" from the Main NG Comm. Failed
Menu
→ System "Immobilizer" → Smart
System "NO" → IGN-ON "YES" →
Meter/SCU registration
Status (procedure)
2
1
No.
A list of possible trouble mode, when an error screen is displayed at each status (procedure).
8-7 Correspondence table when registration is not possible
S1001BE.fm
E type
REGISTRATION MANUAL FOR IMMOBILIZER
Vehicle-id:
SIE-id::
Å`
２０１４年４月３０日
126
Immobilizer CM unregistered
-
NG EGI-SSM Communication
Registered number = 0
Registered number = 1
Check DTC and perform the diagnosis.
Prepare the registered key.
Transponder failure
Antenna failure
•NG key
•Unregistered key
Immobilizer CM failure
NG Abnormal Termination
NG Transponder communication
failure.
NG Immobilizer antenna failure.
NG Transponder collation failure.
NG Non-volatile memory failure.
Check DTC and perform the diagnosis.
Prepare the registered key.
Perform the diagnosis for LAN system.
Perform the diagnosis for the remote control engine starter, and
immobilizer CM.
When the same error is indicated again, replace the immobilizer CM.
Perform the diagnosis for LAN system.
Transponder failure
Antenna failure
•NG key
•Unregistered key
IGN-OFF performed during registration mode
CAN communication failure between immobilizer CM and remote
control engine starter
•Remote control engine starter malfunction
• Immobilizer CM malfunction
CAN communication failure between Subaru Select Monitor and
immobilizer CM
NG Abnormal Termination
NG Transponder communication
failure.
NG Immobilizer antenna failure.
NG Transponder collation failure.
NG Performed conditions not
established.
NG Remote Control Engine Starter
communication failure.
NG Remote start registration NG
NG BIU-SSM Communication
→ "Initializing communication..."
14
—
Check DTC and perform the diagnosis.
Check the data monitor. → Check the communication line.
Check version of Subaru Select Monitor.
Replace the immobilizer CM.
•Subaru Select Monitor malfunction
•Immobilizer CM malfunction
Execute "Immobilizer system registration" to register the key.
IGN line of immobilizer CM not detected
Immobilizer CM unregistered
Registered number = 0
Perform the diagnosis for LAN system.
NG BIU-SSM Communication
Cannot confirm ignition ON.
—
IGN-OFF performed during registration mode
CAN communication failure between Subaru Select Monitor and
immobilizer CM
NG Performed conditions not
established.
DTC is detected except for a new unit. Therefore, check DTC and
perform the diagnosis. When multiple attempts of registration did not
solve the problem, replace the immobilizer CM.
Check DTC and perform the diagnosis.
Check the data monitor. → Check the communication line.
Check version of Subaru Select Monitor.
Replace the immobilizer CM.
Subaru Select Monitor malfunction
Immobilizer CM malfunction
—
IGN line of immobilizer CM not detected
Cannot confirm ignition ON.
→ "Turn ON the ignition switch."
11
Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the
battery.
Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)
•ECM failure
•Communication failure between Subaru Select Monitor and ECM
13
→ "Initializing communication..."
10
Check version of Subaru Select Monitor.
Replace the ECM.
•Subaru Select Monitor failure
•ECM failure
NG EGI security access NG
Execute "Immobilizer system registration" to register the key.
Perform the diagnosis for DTC B1576 (P1576).
ECM failure
NG EGI unit EEPROM
"Remote Control Engine Starter
Registration" start
→ "Turn ON the ignition switch."
9
Immobilizer CM failure
NG IMM Control Module EEPROM
Perform the diagnosis for DTC B1577 (P1577).
Retry the procedure.
Perform the diagnosis for DTC B1572 (P1572).
•IGN-OFF performed during registration mode
•Communication failure between ECM and immobilizer CM
NG EGI-Immobilizer communication
Action to be taken
Communication failure with ECM
Trouble mode
Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)
Error screen
午後２時９分
NG EGI-SSM Communication
(Communication line judgment)
水曜日
12
"Immobilizer key ID deletion" start
8
Status (procedure)
126 ページ
→ "EGI initialization / During
registration..."
No.
S1001BE.fm
E type
REGISTRATION MANUAL FOR IMMOBILIZER
127 ページ
２０１４年４月３０日
水曜日
午後２時９分
Vehicle-id:
SIE-id::
Å`
B1571 (P1571) Reference Code Incompatibility
B1575 (P0513) Incorrect Immobilizer Key
B1402 Immobilizer Key Collation NG
B1575 (P0513) Incorrect Immobilizer Key
B1571 (P1571) Reference Code Incompatibility
B1402 Immobilizer Key Collation NG
List of DTC codes, when the immobilizer is not registered
S1001BE.fm
E type
REGISTRATION MANUAL FOR IMMOBILIZER
127
S1001BE.fm
128 ページ
２０１４年４月３０日
水曜日
午後２時９分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
8-8 Immobilizer control module
B: Installation
A: Removal
• Before handling the airbag module, refer to
"CAUTION" in "General Description" described in
the "AIRBAG SYSTEM" section.
• Before handling the airbag module, refer to
"CAUTION" in "General Description" described in
the "AIRBAG SYSTEM" section in the service
manual.
• Do not let the harness and connector interfere or
tangle with other parts.
• When the steering wheel and steering angle
sensor (steering roll connector) are removed,
perform "VDC sensor midpoint setting mode" of
VDC.
1) Replace the air duct cover LWR.
• Do not let the harness and connector interfere or
tangle with other parts.
• When the steering wheel and steering angle
sensor (steering roll connector) are removed,
perform "VDC sensor midpoint setting mode" of
VDC.
1) Disconnect the ground terminal from the
battery sensor, wait for 60 seconds or more and
begin the procedure.
2) Remove the instrument panel assembly.
3) Remove the heater and cooling unit assembly.
4) Remove the immobilizer control module.
(1) Remove the tapping screw to remove the
immobilizer control module.
Caution:
Make sure to replace the cover LWR. Without
the replacement, the immobilizer control
module cannot be tightened to the specified
torque.
2) Install the immobilizer control module.
Tightening torque:
2.0 N·m (0.2 kgf-m, 1.5 ft-lb)
3) Install the heater and cooling unit assembly.
4) Install the instrument panel assembly.
5) Install the ground terminal to the battery
sensor.
IM-00639
128
Vehicle-id:
SIE-id::
Å`
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
PDF Not Avaliable. View on NHTSA Website
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
- MC-10092539-2280.pdf (6.26 MB)
- SB-10092539-2280.pdf (6.26 MB)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: RMI
Replacement Service Bulletin Number:
MFR Communication Date: 2015-08-26
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.