• Do not let the harness and connector interfere or
tangle with other parts.

Caution:
Make sure to replace the cover LWR. Without
the replacement, the immobilizer control
module cannot be tightened to the specified
torque.
2) Install the ID code box.

• When the steering wheel and steering angle
sensor (steering roll connector) are removed,
perform "VDC sensor midpoint setting mode" of
VDC.
1) Disconnect the ground terminal from the
battery sensor, wait for 60 seconds or more and
begin the procedure.
2) Remove the instrument panel assembly.
3) Remove the heater and cooling unit assembly.
4) Remove the ID code box.
(1) Remove the tapping screw to remove the
immobilizer control module.

Tightening torque:
2.0 N·m (0.2 kgf-m, 1.5 ft-lb)
3) Install the heater and cooling unit assembly.
4) Install the instrument panel assembly.
5) Install the ground terminal to the battery
sensor.

IM-00639

109

Vehicle-id:
SIE-id::
Å`

S1001BE.fm

110 ページ

２０１４年４月３０日

水曜日

午後２時９分

E type
REGISTRATION MANUAL FOR IMMOBILIZER

8 E type

C: Caution

Vehicle without keyless access with push button
start system, without security ID (security tag)
when the vehicle is new, and with immobilizer CM.

• When you install wireless radios or car
phones, make sure that the immobilizer
system is not influenced by their electric
waves.

Note:
U.K./CANADA

• Do not operate cell phones or wireless radios
or the like when either trouble diagnosis or
immobilizer registration is in progress.

A: Structure
An immobilizer system consists of the following
components: Immobilizer indicator (in combination
meter), ECM, ignition key, immobilizer antenna,
and immobilizer CM.

• During immobilizer registration, do not bring
a key with a different ID close to the ignition
switch. When the key is on a keychain,
remove it from the chain before start of
diagnosis. When there are several keys on
one keychain, remove them from the
keychain and use them individually for the
work.

B: Operation
When the ignition key with built-in transponder is
inserted in the key cylinder, the immobilizer CM
receives ignition key ID via the immobilizer
antenna.
The received key ID is collated with the key ID
stored in the memory of immobilizer CM.
Then, the engine IDs stored in the memory of the
ECM and immobilizer CM are collated.
If the IDs do not match within the specified period of
time after the RPM of the engine reaches the
specified RPM, the engine stops.
If the IDs do not match, the engine stops within a
couple of seconds. If the engine does not start as a
result of a mismatch of the IDs, the immobilizer
indicator in the combination meter turns on to
indicate that the immobilizer is active. When the
ignition key is removed, the immobilizer is activated
and the immobilizer indicator lamp flashes to
generate an alert notifying people around the
vehicle that it is protected by the immobilizer.

• When the engine cannot be started with a
registered key, pull the ignition key from the
ignition switch, wait approximately one
second until the immobilizer warning lamp
starts flashing, and then turn the ignition key
slowly to start the engine.
• Confirm that the battery voltage is 11 V or
more and execute each mode.
• During immobilizer registration, make sure
connectors do not get disconnected.
Note:
When performing either one of the operations
shown below, perform also the "Registering
Remote Control Engine Starter".
• Installing remote control engine starter
• Replacing remote control engine starter
• Replacing immobilizer CM of the vehicle with
remote control engine starter

110

Vehicle-id:
SIE-id::
Å`

S1001BE.fm

111 ページ

２０１４年４月３０日

水曜日

午後２時９分

E type
REGISTRATION MANUAL FOR IMMOBILIZER

8-1 Registering Immobilizer CM

4) Click the [YES] button if the System Check
screen is displayed.

Caution:
Only when the immobilizer CM was replaced.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. Using the key you want to
register, turn on the ignition switch. (Refer to
"PC application help for Subaru Select
Monitor".)
2) On the Main Menu, select [All other models].

IM-00404

IM-00404

Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
keyless access with push button start system.
Click the [NO] button.

IM-00491

IM-00405

3) Select [Immobilizer] from the item selection
dialog box.

IM-00405

Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
access with push button start system] used in this
text.
6) Click [YES] after confirming if the ignition switch
is ON, as following screen will be displayed.

IM-00492

Note:
When an error screen is displayed, refer to No. 1 in
"8-7 Correspondence table when registration is not
possible".

IM-00406

IM-00406

111

Vehicle-id:
SIE-id::
Å`

S1001BE.fm

112 ページ

２０１４年４月３０日

水曜日

午後２時９分

E type
REGISTRATION MANUAL FOR IMMOBILIZER

7) On the Main Menu that appears on the display,
select [Immobilizer system registration].

Note:
When an error screen is displayed, refer to No. 3 in
"8-7 Correspondence table when registration is not
possible".

Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is A type. See the
procedures for A type vehicle.

IM-00605

11) Stand by as the key is registered.
Note:
When an error screen is displayed, refer to No. 3 in
"8-7 Correspondence table when registration is not
possible".

IM-00615

8) On the registration mode confirmation dialog
box that appears, click the [OK] button.

IM-00621

IM-00606

9) Registration content appears. Confirm that the
ignition is turned ON using the key you want to
register, and click the [OK] button.

12) The screen shown below will appear if
registration ends normally. If you have another
keys to be registered, insert the next key into
the ignition switch, turn on the ignition key, and
return to step 11. If you have no more keys to
be registered, click the [Exit] button.

Note:
When an error screen is displayed, refer to No. 2
and 3 in "8-7 Correspondence table when
registration is not possible".

Note:
When an error screen is displayed, refer to No. 3
and 4 in "8-7 Correspondence table when
registration is not possible".

IM-00604

10) Stand by as the communication initialization is
performed.

IM-00607

112

Vehicle-id:
SIE-id::
Å`

S1001BE.fm

113 ページ

２０１４年４月３０日

水曜日

午後２時９分

E type
REGISTRATION MANUAL FOR IMMOBILIZER

16) The screen shown below will appear if
registration ends normally. Remove the key and
click the [OK] button.

Note:
a = Number of registered key
13) Stand by as the key registration ends.
Note:
When an error screen is displayed, refer to No. 4 in
"8-7 Correspondence table when registration is not
possible".

IM-00611

17) Make sure the engine can be started with all the
registered keys, then quit the registration
procedure.
IM-00608

14) Stand by as next registration continues.
Note:
When an error screen is displayed, refer to No. 4 in
"8-7 Correspondence table when registration is not
possible".

IM-00609

15) The screen shown below will appear if
registration ends normally. Check the number
of registered keys, and click the [OK] button.

IM-00610

Note:
a = Number of registered key

113

Vehicle-id:
SIE-id::
Å`

S1001BE.fm

114 ページ

２０１４年４月３０日

水曜日

午後２時９分

E type
REGISTRATION MANUAL FOR IMMOBILIZER

8-2 Adding Keys

4) Click the [YES] button if the System Check
screen is displayed.

Caution:
To add keys, you need one registered key.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. Using the registered key, turn on
the ignition switch. (Refer to "PC application
help for Subaru Select Monitor".)

IM-00404

Caution:
Make sure to use a registered key.
2) On the Main Menu, select [All other models].

IM-00404

Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
keyless access with push button start system.
Click the [NO] button.

IM-00405
IM-00491

3) Select [Immobilizer] from the item selection
dialog box.
IM-00405

6) Click [YES] after confirming if the ignition switch
is ON, as following screen will be displayed.
Note:
When an error screen is displayed, refer to No. 1 in
"8-7 Correspondence table when registration is not
possible".
IM-00492

IM-00406

IM-00406

114

Vehicle-id:
SIE-id::
Å`

S1001BE.fm

115 ページ

２０１４年４月３０日

水曜日

午後２時９分

E type
REGISTRATION MANUAL FOR IMMOBILIZER

7) On the Main Menu that appears on the display,
select [Immobilizer system registration].

Note:
When an error screen is displayed, refer to No. 3 in
"8-7 Correspondence table when registration is not
possible".

Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is A type. See the
procedures for A type vehicle.

IM-00605

11) Stand by as the key is being collated.

IM-00615

Note:
When an error screen is displayed, refer to No. 3 in
"8-7 Correspondence table when registration is not
possible".

8) On the registration mode confirmation dialog
box that appears, click the [OK] button.

ࠠ࡯ᾖวਛ̖

IM-00621

9) Registration content appears. Confirm that the
ignition is turned ON with the registered key,
and then click the [OK] button.

IM-00613

12) The key collation completion screen appears.
Turn the ignition switch OFF, and using a key to
be newly registered, turn the ignition switch
ON.

Note:
When an error screen is displayed, refer to No. 2
and 3 in "8-7 Correspondence table when
registration is not possible".

Note:
When an error screen is displayed, refer to No. 3 in
"8-7 Correspondence table when registration is not
possible".

IM-00612
⚳ੌ

Note:
n = Number of registered key
10) Stand by as the communication initialization is
performed.

IM-00614

13) Stand by as the key is registered.

115

Vehicle-id:
SIE-id::
Å`

S1001BE.fm

116 ページ

２０１４年４月３０日

水曜日

午後２時９分

E type
REGISTRATION MANUAL FOR IMMOBILIZER

16) The screen shown below will appear if
registration ends normally. Check the number
of registered keys, and click the [OK] button.

Note:
When an error screen is displayed, refer to No. 3 in
"8-7 Correspondence table when registration is not
possible".

IM-00610
IM-00606

Note:
a = Number of registered key
17) The screen shown below will appear if
registration ends normally. Remove the key and
click the [OK] button.

14) The screen shown below will appear if
registration ends normally. If you have another
keys to be registered, insert the next key into
the ignition switch, turn on the ignition key, and
return to step 13. If you have no more keys to
be registered, click the [Exit] button.
Note:
When an error screen is displayed, refer to No. 3 in
"8-7 Correspondence table when registration is not
possible".

IM-00611

18) Make sure the engine can be started with all the
registered keys, then quit the registration
procedure.

IM-00607

Note:
a = Number of registered key
15) Stand by as the key registration ends.

IM-00608

116

Vehicle-id:
SIE-id::
Å`

S1001BE.fm

117 ページ

２０１４年４月３０日

水曜日

午後２時９分

E type
REGISTRATION MANUAL FOR IMMOBILIZER

8-3 Registering Engine ECM

4) Click the [YES] button if the System Check
screen is displayed.

Caution:
To add keys, you need one registered key.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. Using the registered key, turn on
the ignition switch. (Refer to "PC application
help for Subaru Select Monitor".)
Caution:
Make sure to use a registered key.
2) On the Main Menu, select [All other models].

IM-00404

Note: