“This site contains affiliate links for which OEMDTC may be compensated” |
July 30, 2021 NHTSA CAMPAIGN NUMBER: 21V588000
Detached fuel tank brackets could allow the fuel tank to separate from the vehicle, increasing the risk of a crash or injury.
NHTSA Campaign Number: 21V588
Manufacturer Wabash National Corporation
Components FUEL SYSTEM, GASOLINE
Potential Number of Units Affected 352
Summary
Wabash National Corporation (Wabash) is recalling certain 2018-2022 Van Trailers. The fuel tank brackets may detach.
Remedy
Dealers will add an aluminum plate and 4 fasteners to each bracket, free of charge. Owner notification letters were mailed on August 18, 2021. Owners may contact Wabash customer service at 1-765-771-5404. Wabash’s number for this recall is B21012.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
BULLETIN
Subject: | Securement of Bonded Fuel Tank Brackets | ||||
Date: | August 10, 2021 | Rev.: | FR | No.: | B21012 |
Re.: | Connection Inspection and Installation of Redundant Fasteners. | Type: | Safety | ||
Priority: | Earliest Opportunity | ||||
Units Affected: | Please see VIN # listing. |
Background:
We have received reports of certain Bonded Fuel Tank brackets becoming detached from the composite Longitudinal beam. This bulletin will explain how to add Doubler plates and Redundant fasteners to this connection for added strength.
Materials:
Item | Part Number | Qty. |
Doubler Plate | 08A00817 | 2 |
Bolts | BLT00871 | 8 |
Nuts | NUT00001 | 8 |
Washers | WSH00006 | 16 |
Adhesive | 93350081 | 1 |
Tools:
Caulking Gun
Drill
Right Angle Drill
9/16” Socket
9/16” Wrench
3/8” Drill Bit
7/16” Wrench
TX 30 Torx Bit
Impact Wrench
Accetone or Isopropyl Aclohol
Paper Towels
Pad Sander
40 Grit Sandpaper
Vice Grip Clamps
CAUTION!
- Wear appropriate personal protective equipment [PPE] like gloves, safety glasses and hard hat for example, when carrying out the following procedure.
- Should welding or cutting be needed, do so in a well ventilated area and wear appropriate head/face/eye protection, welding gloves and clothing.
- Refer to adhesive and chemical manufacturer’s MSDS for safe use and handling instructions if applicable.
- Follow your company’s safety procedures in addition to these recommendations.
- Follow industry standards for installation and tightening of all fasteners where torque values are not called out
Procedure:
- Remove the single fastener securing the Safety Tether at the mid-point of the same panel.
- With the Skirt Panel still attached to the second Spring Post, carefully push down on the panel and pull out and away to provide access to the fuel tank.
This is an exploded view of the parts you will be installing
- Position the Aluminum Doubler Plate inside the upper channel of the existing Tank bracket.
- Once the Doubler plate is properly positioned, use it as a template to mark the 4 holes for drilling.
- Using a 3/8” drill bit, drill through the existing tank bracket and into the Longitudinal beam. Note: Use caution to not drill all the way through the beam.
- Using a combination square, mark a line across the beam in line with the end of the existing tank bracket.
- Line up the aluminum doubler plate and clamp it into position. Note: Use caution to not push the plate up too high. It should sit flat and tight to the side of the beam.
- Using a Right Angle drill, drill through the beam and out through the previously drilled holes in the existing bracket. Note: A 6.5” to 7” bit is optimal for this step.
- Once all holes are drilled, prep the Aluminum plate and Composite beam for gluing and bolting.
Prep the Composite beam by thoroughly cleaning with paper towel and Accetone or Isopropyl alcohol.
Prep the mating surface of the Aluminum plate using 40 grit nonstearate paper, and follow up with a thorough Accetone or Alcohol wipe.
- Apply three ¼” beads of the provided Industrial adhesive as shown.
- From the outside in, insert the two outboard (end) bolts. Place the aluminum plate over the two bolts with the adhesive towards the mounting beam.
- Install flat washers and nuts on to the two installed bolts and tighten snug. Repeat these steps for the two remaining inboard bolts. Note: Use caution to not overtighten the fasteners or the Composite beam may become damaged.
- Torque the nuts to 20 ft. lbs. +/– 2 ft. lbs.
The outboard side of the tank is now complete.
- Repeat steps 7 and 8 from above for the inboard Tank bracket.
- Once the doubler plate is clamped into position, using an adequate length bit, drill all the way through the Composite beam and the existing Tank bracket using the Overlay plate as a drill template.
- Once all four holes are drilled, with the exception of these bolts being installed from the inside out, repeat steps 10,11,12,13,and 14 from above.
- Once both aluminum plates have been installed and properly torqued, caulk around the perimeter of both plates. Also caulk around the perimeter of existing fuel tank mounting brackets if factory caulk is poor or absent.
- Reattach the Skirt panel using the pre-existing hardware.
The Recall Bulletin is now complete and should resemble the following model.
Special Instructions
- Prior to starting this repair, both existing Tank brackets should be inspected for signs of de-bonding or looseness.
- If any existing brackets are found to have issues please send pictures to johnson@wabashnational.com & john.gabriel@wabashnational.com
- Should you have questions or concerns about this repair please contact Eric Johnson @ 765-771-5444, John Gabriel @ 765-771-5428 or Brent Howard @765-237-8426
- The SRT for this Recall repair is 2.5 hours per unit affected.
- Be cautious of all sharp edges in the surrounding work area.
- Clamp time on Loctite adhesive is 24 hours. We suggest that the trailer be parked for 24 hours after this repair before returning to service.
- Loctite PL Premium-3X adhesive is being used for this repair bulletin only. Loctite PL Premium-3X adhesive should not be used for any other repairs or additions to any Wabash National products without Engineering approval from Wabash National.
August 11, 2021
IMPORTANT SAFETY RECALL
NHTSA Recall# 21V-588
This applies to your vehicle, see attached VIN list
Dear Wabash National Corporation Customer,
This notice is being sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Wabash National Corporation (WNC) has decided that a defect which relates to motor vehicle safety exists in certain 2018-2022 model year Wabash National Van trailers equipped with bonded fuel tank brackets.
A complete listing of your trailers impacted by this recall is included with this letter.
Description of Defect:
The fuel tank brackets installed on certain refrigerated van trailers may become detached
Risk to Motor Vehicle Safety:
If the fuel tank brackets become detached while the trailer is in motion, there is an increased risk of an accident or injury.
Precautions You Should Take:
The condition of the fuel tank brackets typically will not be apparent during routine inspections. A visual inspection is needed to see if one of the fuel tank brackets is detached. We feel that this inspection should take place as soon as practical, but not to exceed your normal PM cycle.
Remedy:
Enclosed with this notification is WNC Safety Bulletin “B21012”, and a list of the affected equipment. The equipment listed within, should be inspected and remedied per the instructions described in bulletin B21012. This repair should take approximately 2.5 hours and will be performed at no cost to the owner. The owner may perform this recall and be reimbursed by Wabash National, or you may contact your nearest Wabash National Warranty Provider for assistance. If you need help finding a Warranty Provider, please contact the Wabash National Warranty Department at 765-771-5404, Monday – Friday, 7:00am – 4:00pm, ET.
If this repair has been performed at cost to the owner prior to receipt of this notification, the owner may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. For more information, contact the Wabash National Warranty Department at 765-771-5404, Monday – Friday, 7:00am – 4:00pm, ET.
Further Assistance:
If your affected trailers have not been repaired within a reasonable amount of time after this defect notification, or if you have additional questions regarding this recall, please contact the Wabash National Warranty Department at 765-771-5404, Monday – Friday, 7:00am – 4:00pm, ET.
If you are the lessor of this vehicle, please forward a copy of this notice to the lessee within 10 days to comply with federal regulations.
Complaints:
You may also submit complaints to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., S.E., Washington, D.C. 20590 or call the toll-free vehicle safety hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov, if it is believed that the defect has not been remedied without charge or within a reasonable time.
We apologize for the inconvenience caused by this safety recall.
Thank you,
Mike Jones
Warranty Manager
Wabash National
1000 Sagamore Parkway S
Lafayette, IN 47905
August 11, 2021
IMPORTANT SAFETY RECALL
NHTSA Recall# 21V-588
This applies to your vehicle, see attached VIN list
Dear Wabash National Corporation Dealer,
This notice is being sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Wabash National Corporation (WNC) has decided that a defect which relates to motor vehicle safety exists in certain 2018-2022 model year Wabash National Van trailers equipped with bonded fuel tank brackets.
A complete listing of your trailers impacted by this recall is included with this letter.
Description of Defect:
The fuel tank brackets installed on certain refrigerated van trailers may become detached
Risk to Motor Vehicle Safety:
If the fuel tank brackets become detached while the trailer is in motion, there is an increased risk of an accident or injury.
Precautions You Should Take:
The condition of the fuel tank brackets typically will not be apparent during routine inspections. A visual inspection is needed to see if one of the fuel tank brackets is detached. We feel that this inspection should take place as soon as practical, but not to exceed your normal PM cycle.
Remedy:
Enclosed with this notification is WNC Safety Bulletin “B21012”, and a list of the affected equipment. The equipment listed within, should be inspected, and remedied per the instructions described in bulletin B21012. This repair should take approximately 2.5 hours and will be performed at no cost to the owner. The owner may perform this recall and be reimbursed by Wabash National, or you may contact your nearest Wabash National Warranty Provider for assistance. If you need help finding a Warranty Provider, please contact the Wabash National Warranty Department at 765-771-5404, Monday – Friday, 7:00am – 4:00pm, ET.
If this repair has been performed at cost to the owner prior to receipt of this notification, the owner may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. For more information, contact the Wabash National Warranty Department at 765-771-5404, Monday – Friday, 7:00am – 4:00pm, ET.
Further Assistance:
If your affected trailers have not been repaired within a reasonable amount of time after this defect notification, or if you have additional questions regarding this recall, please contact the Wabash National Warranty Department at 765-771-5404, Monday – Friday, 7:00am – 4:00pm, ET.
If you are the lessor of this vehicle, please forward a copy of this notice to the lessee within 10 days to comply with federal regulations.
Complaints:
You may also submit complaints to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., S.E., Washington, D.C. 20590 or call the toll-free vehicle safety hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov, if it is believed that the defect has not been remedied without charge or within a reasonable time.
We apologize for the inconvenience caused by this safety recall.
Thank you,
Mike Jones
Warranty Manager
Wabash National
1000 Sagamore Parkway S
Lafayette, IN 47905
P.O. Box 6129 | Lafayette, IN 47903 | Phone: (765) 771-5300
5 Affected Products
Vehicle
MAKE | MODEL | YEAR |
WABASH NATIONAL | VAN | 2018-2022 |
10 Associated Documents
Defect Notice 573 Report
RCLRPT-21V588-8047.PDF 215.511KB
Recall Acknowledgement
Recall 573 Report – Amendment 2
RCLRPT-21V588-2922.PDF 215.513KB
ISSUED Owner Notification Letter(Part 577)
RCONL-21V588-4004.pdf 400.043KB
Recall 573 Report – Amendment 1
RCLRPT-21V588-3149.PDF 215.511KB
Remedy Instructions and TSB
RCRIT-21V588-7513.pdf 1595.545KB
Manufacturer Notices(to Dealers,etc)
Recall Quarterly Report #2, 2021-4
RCLQRT-21V588-2772.PDF 211.233KB
Recall Quarterly Report #1, 2021-3
RCLQRT-21V588-6853.PDF 211.126KB
Recall Quarterly Report #3, 2022-1
RCLQRT-21V588-0109.PDF 211.316KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=21V588&docType=RCL
“This site contains affiliate links for which OEMDTC may be compensated” |
- Outstanding Suitability: Fuel Tank Hanger w/Strap Compatible with 1973-1986 Chevy Chevrolet & GMC Pickup Truck C/K Series, 1987-1991 Chevy Chevrolet & GMC Pickup Truck R/V Series.
- Note: Sold as a pair. This gas tank hanger replacement is for the front & rear gas tank support. Can be used for left or right side mounted fuel gas tanks.
- Durable Steel: This tank hanger is made of high quality steel for added overall strength to withstand heavy loads. The black electrophoresis process further adds additional protection against rust and other environmental factors.
- Safe Tank Mounting: Designed to provide a secure mounting system for your vehicle's fuel tank. It ensures that the front & rear side mounted fuel tank stays in place under rigorous driving conditions. No need for the fuel tank to be displaced or damaged while driving.
- Package Contents: Only 2 x fuel tank hanger with straps (front & rear side mounted). No instructions or mounting hardware. Replace your rusted or damaged gas tank straps and brackets with these replacement parts.
- Outstanding Suitability: Fuel Tank Hanger w/Strap Compatible with 1973-1986 Chevy Chevrolet & GMC Pickup Truck C/K Series, 1987-1991 Chevy Chevrolet & GMC Pickup Truck R/V Series.
- Note: Sold as a single. This gas tank hanger replacement is for the rear gas tank support. Can be used for left or right side mounted fuel gas tanks.
- Durable Steel: This tank hanger is made of high quality steel for added overall strength to withstand heavy loads. The black electrophoresis process further adds additional protection against rust and other environmental factors.
- Safe Tank Mounting: Designed to provide a secure mounting system for your vehicle's fuel tank. It ensures that the rear side mounted fuel tank stays in place under rigorous driving conditions. No need for the fuel tank to be displaced or damaged while driving.
- Package Contents: Only 1 x fuel tank hanger with strap (rear side mounted). No instructions or mounting hardware. Replace your rusted or damaged gas tank straps and brackets with these replacement parts.
- [Fitment]: Fuel Tank Hanger fit for 1973-1986 Chevy & GMC pickup c/k series;for 1987-1991 Chevy & GMC pickup r/v series
- [Part Number]: 15549305, 15592480, 15624659
- [Durable performance]: Made of high quality steel, this Gas Tank Hanger is extremely durable and robust. Made according to strict production standards.
- [Safe driving]: The Fuel Tank Hangers' good quality can give you more peace of mind during the driving process.
- [Note] : The contents of the package are shown in the figure. Please make sure that your model is suitable for this product before purchasing.
- 98-8741-0 Fuel Tank Retainer, Set Of 4 NEW!
- Compatible With Volkswagen Type 1 1949 to 1979, Ghia 1956 to 1974, Type 3 1962 to 1973 and Thing 1973 to 1974
- Gas Tank Hold Down Brackets
- These Brackets / Tabs are used to secure the fuel tank to the body
- Sold as all four Brackets which are required per car
- For mounting 6" diameter tanks
- With 0.39" screw hole, 4.33"hole distance
- Black finish
- Universal Fit
- 1 year Warranty
- for propane tank mount propane tank holder fuel bottle holder nitrous tank bottle
- Model number : 63401
- Direct replacement - this fuel tank strap matches the fit, function and performance of the original part.Material:Steel
- Ideal solution - recommended for replacement when the fuel tank is serviced or replaced
- Durable construction - manufactured from quality materials for superior service and reliability
- Trustworthy design - backed by 100 years of automotive aftermarket experience
- Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool
- Great Compatibility: The Fuel Tank Strap, will be compatible with 1988-1998 Chevrolet GMC 1500 C/K Pick Up. Compatible with 1988-2000 Chevrolet GMC 2500 3500 C/K Pick Up.
- Function:The Fuel Tank Strap is designed to securely hold the fuel tank in place, ensuring that it remains stable during transportation and vehicle operation.
- High-quality Materials: Fuel Tank Straps are made from high-quality steel. Anti-oxidation by electrophoresis ensures to withstand harsh conditions and provide long-lasting performance.
- Easy Installation: Direct Bolt-on. Fuel Tank Straps are designed for easy installation. It can be quickly and securely attached to the vehicle.
- Package Included: 1 × Fuel Tank Strap. Instructions and installation accessories are not included.
- Outstanding Suitability: Fuel Tank Hanger w/Strap Compatible with 1973-1986 Chevy Chevrolet & GMC Pickup Truck C/K Series, 1987-1991 Chevy Chevrolet & GMC Pickup Truck R/V Series.
- Note: Sold as a single. This gas tank hanger replacement is for the front gas tank support. Can be used for left or right side mounted fuel gas tanks.
- Durable Steel: This tank hanger is made of high quality steel for added overall strength to withstand heavy loads. The black electrophoresis process further adds additional protection against rust and other environmental factors.
- Safe Tank Mounting: Designed to provide a secure mounting system for your vehicle's fuel tank. It ensures that the front side mounted fuel tank stays in place under rigorous driving conditions. No need for the fuel tank to be displaced or damaged while driving.
- Package Contents: Only 1 x fuel tank hanger with strap (front side mounted). No instructions or mounting hardware. Replace your rusted or damaged gas tank straps and brackets with these replacement parts.
- ⛽Our fuel tank bracket lock is universal fit for 3L or 5L fuel tank.PLEASE NOTE: Before purchasing, please compare whether the hole shape of the oil drum is suitable
- ⛽It is well made of Advanced Engineering Plastics and Metals.
- ⛽Using these sturdy mounting brackets help 3L / 5L fuel bottle stay steady and will not fall down which provide you with a safe driving environment.
- ⛽Convenient to use. Easy to install and remove. It is mountable in different locations. You can install it in different locations according to your needs.
- ⛽Package Include:1x Jerry Can Mount for Motorcycle
Last update on 2024-03-18 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.