“This site contains affiliate links for which OEMDTC may be compensated” |
July 21, 2021 NHTSA CAMPAIGN NUMBER: 21V548000
Leveling Sprocket Weld Failure
Uncontrolled platform leveling increases the risk of injury and death.
NHTSA Campaign Number: 21V548
Manufacturer Altec Industries, Inc.
Components EQUIPMENT
Potential Number of Units Affected 1,284
Summary
Altec Industries, Inc. (Altec) is recalling certain 2020 AA5X/AN5X, AA5X(E)/AN5X(E), AA6X/AN6X, AA6X(E)/AN6X(E), AN4X-OC/AN4X(E)-OC, AN5X-OC/AN5X(E)-OC, AA/AN67-E100, and AA/AN67(E)-E100 vehicles. The leveling sprocket may have a failed weld between the sprocket and hub assembly.
Remedy
Altec will inspect and replace the damaged sprocket assembly, free of charge. If no damage is observed, a secondary retention kit will be installed to limit rotation of the platform, free of charge. Owner notification letters were mailed on September 15, 2021. Owners may contact Altec’s customer service at 1-877-462-5832. Altec’s number for this recall is CSN 828.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
IMPORTANT SAFETY RECALL
This notice applies to your vehicle. See attached serial number list.
NHTSA Safety Recall
No. 21V-548
September 16, 2021
Dear Altec Owner,
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act, and Canada Motor Vehicle Safety Act.
Altec Industries, Inc. has decided that a defect which relates to motor vehicle safety exists in certain AA/AN and AN-OC series aerial devices built from March 2020 to November 2020. These units may have a leveling sprocket with poor quality weld. Weld failure could cause the platform to tip. If the platform tips with an operator not wearing the required fall protection equipment, the operator could fall from the platform. Death or serious injury can result from a fall from the platform.
In order to determine if your unit is affected by this CSN, compare the serial number of your unit with the list of affected units attached to the notice. Refer to attached notice for the items covered under the warranty policy. The repair can be performed by the customer or you may contact Altec at 1-877-GO-ALTEC (1-877-462-5832) for further assistance. The repair is expected to take up to 51/2 hours to complete.
If you had this repair performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall.
At any time, you may contact Altec at 1-877 GO ALTEC (1-877-462-5832) with your unit’s serial number to determine if there are any other outstanding notices.
If you have sold or retired the unit, please call Altec at 1-877-GO-ALTEC (1-877-462-5832) so the records may be changed.
If you have leased this equipment to another person or company, you are required by Federal Law to forward a copy of this notice to the lessee by first class mail within ten (10) days of the receipt of this notice.
For US owners: after contacting Altec, if you are still not able to have the safety condition remedied without charge and within a reasonable time, you may submit a complaint to: Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, DC 20590 or call toll-free 1-888-327-4236 (TTY: 1-800-424-9153) or go to https://www.safercar.gov.
For Canadian Owners: if you are still not able to have the safety condition remedied by your dealer within a reasonable time, please contact Altec Customer Service at 1-877-GO-ALTEC (1-877-462-5832).
We are sorry to cause this inconvenience; however, we are taking this action in the interest of your safety and continued satisfaction with Altec products.
Thank you for your immediate attention on this important matter.
SEOCONTENT-START
September 16, 2021
Dear Altec Owner,
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act, and Canada Motor Vehicle Safety Act.Altec Industries, Inc. has decided that a defect which relates to motor vehicle safety exists in certain AA/AN and AN-OC series aerial devices built from March 2020 to November 2020. These units may have a leveling sprocket with poor quality weld. Weld failure could cause the platform to tip. If the platform tips with an operator not wearing the required fall protection equipment, the operator could fall from the platform. Death or serious injury can result from a fall from the platform.In order to determine if your unit is affected by this CSN, compare the serial number of your unit with the list of affected units attached to the notice. Refer to attached notice for the items covered under the warranty policy. The repair can be performed by the customer or you may contact Altec at 1-877-GO-ALTEC (1-877-462-5832) for further assistance. The repair is expected to take up to 51/2 hours to complete.If you had this repair performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. At any time, you may contact Altec at 1-877 GO ALTEC (1-877-462-5832) with your unit’s serial number to determine if there are any other outstanding notices.If you have sold or retired the unit, please call Altec at 1-877-GO-ALTEC (1-877-462-5832) so the records may be changed.If you have leased this equipment to another person or company, you are required by Federal Law to forward a copy of this notice to the lessee by first class mail within ten (10) days of the receipt of this notice.For US owners: after contacting Altec, if you are still not able to have the safety condition remedied without charge and within a reasonable time, you may submit a complaint to: Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, DC 20590 or call toll-free 1-888-327-4236 (TTY: 1-800-424-9153) or go to https://www.safercar.gov. For Canadian Owners: if you are still not able to have the safety condition remedied by your dealer within a reasonable time, please contact Altec Customer Service at 1-877-GO-ALTEC (1-877-462-5832).We are sorry to cause this inconvenience; however, we are taking this action in the interest of your safety and continued satisfaction with Altec products.Thank you for your immediate attention on this important matter.
NHTSA Safety Recall
No. 21V-548
IMPORTANT SAFETY RECALL
This notice applies to your vehicle. See attached serial number list.
210 Inverness Center Parkway Telephone: 205-991-7733
Birmingham, AL 35242 Facsimile: 205-991-9993
www
.altec.com
Page 1 of 7
Altec Industries, Inc.
Midwest Operations
St. Joseph, MO
CSN 828
Customer Service Notice
September 16, 2021
Units Affected: AA/AN and AN-OC series aerial devices built from March 2020 to November 2020 (Verify that your unit serial number is affected by reviewing the attached list in this CSN or by accessing your fleet on connect.altec.com/login)
Elbow Leveling Sprocket Inspection
Altec is committed to providing our customers with safe and reliable products from initial delivery throughout the useful life of the unit.
The leveling sprocket weldment in the elbow of the affected units is purchased from more than one manufacturer. Altec has discovered that the sprocket weldments provided by one supplier may have poor quality welds between the sprockets and the hub. A sprocket can turn freely on the hub if its weld fails, resulting in uncontrolled platform leveling. If the platform tips with an operator not wearing the required fall protection equipment, the operator could fall from the platform. Death or serious injury can result from a fall from the platform.
Altec requires the elbow leveling sprocket weldment to be inspected on each unit to verify the manufacturer and determine whether the sprocket must be repaired or replaced. This must be done no later than 30 days from the receipt of this CSN. Use the Inspection Procedure beginning on page 2.
If the inspection determines that the sprocket was supplied by the manufacturer in question, inspection of the welds is prescribed. Order the specified kit based on the result of the weld inspection, and install it upon receipt.
This inspection and repair are covered under the Altec Warranty Policy and can be performed by Altec, the customer, or the customer’s warranty provider. The sprocket replacement requires a hoist and sling rated for 4,000 pounds, and up to 1,200 pounds of test load for a structural test. Altec will perform the work for free at an Altec facility. If the customer or the customer’s warranty provider performs the work, a warranty claim must be submitted to be reimbursed for the cost of the parts and/or labor. Altec will allow up to $45 for the labor to perform the inspection, up to $45 for the labor to install the sprocket retainer kit, and up to $405 for the labor to replace the sprocket. Altec will allow an additional $90 for the labor to remove and reinstall the hose retainer assembly, if equipped, during the inspection or repair of an AN-OC series unit.
Altec Use Only
Parts Kit
Part No.
Qty
Warranty
Elbow sprocket retainer kit
991370742
1
Yes
Elbow sprocket replacement kit, AA/AN Series
991381820
1
Yes
Elbow sprocket replacement kit, AN-OC Series
991381821
1
Yes
Altec Use Only
Inspection labor
0.5 hr (AA/AN), 1.5 hr (AN-OC)
Repair labor, retainer kit
0.5 hr (AA/AN), 1.5 hr (AN-OC)
Repair labor, sprocket kit
4.5 hr (AA/AN), 5.5 hr (AN-OC)
Account #
010.1093.43151.447.0000.000
Travel
Not included
NHTSA code
16
Prime fail P/N
970346819, 970236795
Doc ref
074900791, 074900798
Page 2 of 7
CSN 828
Call 1-877-GO ALTEC (1-877-462-5832) option 3 to schedule the work to be done by an Altec Mobile
Service technician or option 2 to schedule the work to be done at an Altec facility. Customers are responsible
for the travel costs of an Altec Mobile Service technician if the technician performs the inspection
and/or repair at the owner’s location.
Inspection Procedure
Normal mechanic’s hand tools, a flashlight, mirror, and step ladder or rolling stairs are required for this
inspection. On an AN-OC series unit, the upper boom may need to be unfolded to 70 degrees for the last
part of the inspection. Read and understand all steps of the instructions before beginning the procedure.
Setup
1. Position the unit on a level surface. Apply the
parking brake, and turn off the engine. Remove
the key from the ignition, and secure it following
your employer’s vehicle lockout/tagout procedure.
Chock the wheels.
2. Determine whether the aerial device is an AA series,
AN series, or AN-OC series unit. The model number
is shown on the serial number placard on the side of
the pedestal.
3. Remove the three fasteners along the top edge
of the boom elbow cover (refer to Figure 1), and
allow the cover to hang down. Keep the fasteners
for reuse.
Identifying Supplier Code
4. Locate the leveling sprocket weldment in the boom elbow (refer to Figure 2). Using a flashlight, if
necessary, look for the five-digit supplier code number stamped on the street side of the sprocket on
the spoke opposite from the center mark (refer to Figure 3)
• If the supplier code is 13037 or if it cannot be identified, proceed to step 5.
• If the supplier code is 50605 or 55843, the inspection is complete. Reattach the top edge of the boom
elbow cover to the upper boom using the original fasteners. Put the unit back into service. Complete
the Inspection Sheet at the end of the CSN and return it to Altec.
Figure 2 – Boom Elbow Components
Leveling
Sprocket
Center Mark
Supplier Code Timing Mark
13037
Figure 3 – Sprocket Markings
Upper Boom
Lower Boom
Figure 1 – Opening Boom Elbow Cover
Boom
Elbow
Cover
Cover
Fasteners
Upper Boom
Lower Boom
Page 3 of 7
CSN 828
Checking AN-OC Unit for Hose Retainer
5. For an AN-OC series unit, proceed to step 6. For an AA series or AN series unit, proceed to
step 13.
6. Look into the end of the elbow to determine if the boom is equipped with a hose retainer assembly
attached to the sprocket (refer to Figure 4).
• If the boom has a hose retainer assembly, proceed to step 7.
• If the boom does not have a hose retainer assembly, proceed to step 13.
Removing Hose Retainer on AN-OC Unit
7. Confirm whether there is sufficient overhead clearance to unfold the upper boom to 70 degrees (refer
to Figure 5). If necessary, move the unit to a suitable level surface with adequate vertical clearance.
Apply the parking brake, and chock the wheels.
8. Start the engine, engage the unit’s hydraulic system, and properly set the outriggers.
9. With the lower boom fully stowed, use the lower controls to unfold the upper boom to approximately
70 degrees.
10. Disengage the unit’s
hydraulic system,
and turn off the engine.
11. Remove the four 3/8”
flat head cap screws
attaching the spacer
block to the hose
retainer body, and
remove the spacer
block (refer to Figure
6).
Figure 4 – Hose Retainer
Hose Retainer
Components
70°
Upper Boom
Lower Boom
Figure 5 – Unfolding Upper Boom
Sprocket
Figure 6 – Removing Spacer Block Figure 7 – Removing Hose Retainer Body
Spacer
Block Hose Retainer
Body
3/8” Flat
Head Cap
Screw
5/16” Hex
Head Cap
Screw
Page 4 of 7
CSN 828
12. Remove the two sets of 5/16” fasteners holding the halves of the hose retainer body together, and remove
the hose retainer body (refer to Figure 7). Keep the hose retainer components and fasteners for
reuse.
Inspecting Welds
13. Using a flashlight and a mirror as required, attempt to visually inspect the weld all around the hub on
the street side of the leveling sprocket for any cracks (refer to Figure 8). Repeat this for the weld on
the curb side of the sprocket, looking through the holes in the guard plate (refer to Figure 9).
• If the weld could be fully inspected 360 degrees around the hub on both sides and a hose retainer was
removed from the elbow, proceed to step 19.
• If the weld could be fully inspected 360 degrees around the hub on both sides and a hose retainer was
not removed from the elbow, proceed to step 22.
• If the weld could not be fully inspected 360 degrees around the hub, use a felt tip marker to mark
what portion of each weld was inspected, and proceed to step 14.
Weld
Figure 8 – Inspecting Weld on Street Side of Sprocket
Weld
Weld
Weld
Figure 9 – Inspecting Weld on Curb Side of Sprocket
Guard Plate
(Cut Away
for Visibility)
Guard
Plate
Holes
Weld
Page 5 of 7
CSN 828
Rotating Sprocket for Further Weld Inspection
14. Start the engine, and engage the unit’s hydraulic system. Properly set the outriggers if they have not
already been set. Use the lower controls to unfold the upper boom far enough out of the rest to provide
adequate clearance below the platform so it can be fully tilted without interfering with any unit structures.
15. Using the upper controls, engage the upper control interlock, lift up on the platform tilt control
interlock, and move the platform tilt control to fully tilt the platform. This will rotate the
sprocket in the elbow for further inspection. Disengage the unit’s hydraulic system and turn
off the engine.
16. Using a flashlight and a mirror as required, visually inspect the remaining portions of the
welds around the hub on both sides of the sprocket that could not be seen previously based
on the markings made in step 13.
17. Start the engine, and engage the unit’s hydraulic system. Using the upper controls, engage the upper
control interlock, lift up on the platform tilt control interlock, and move the platform tilt
control to tilt the platform back to the working position.
18. Using the lower controls, ensure the lower boom is stowed. Position the upper boom as described below.
• If a hose retainer was removed from the elbow, unfold the upper boom to approximately 70 degrees.
Disengage the unit’s hydraulic system, turn off the engine, and proceed to step 19.
• If the elbow was not equipped with a hose retainer, stow the upper boom. Retract the outriggers,
disengage the unit’s hydraulic system, turn off the engine, and proceed to step 22.
Installing and Testing Hose Retainer on AN-OC Unit
19. Reinstall the hose retainer assembly using the original fasteners.
20. Start the engine, and engage the unit’s hydraulic system. Operate the upper and lower booms using
the lower controls to check for proper operation of the hose retainer assembly. Make any necessary
corrections.
21. Use the lower controls to stow the booms. Retract the outriggers, disengage the unit’s hydraulic system,
and turn off the engine.
Completion
22. Reattach the top edge of the boom elbow cover to the upper boom using the original fasteners.
23. Review the inspection results from steps 13 and 16.
• If there are no visible weld crack(s) on the sprocket, put the unit back into service. Call 1-877-
GO ALTEC (1-877-462-5832) option 1 to order the Elbow Sprocket Retainer Kit, part number
991370742. Do not complete the Inspection Sheet at the end of the CSN. A separate reply card will
be provided with the kit to document the completion of the CSN. Install the kit upon receipt.
Page 6 of 7
CSN 828
• If there are visible weld crack(s) on the sprocket, take the unit out of service. Call 1-877-GO ALTEC
(1-877-462-5832) option 1 to order the Elbow Sprocket Replacement Kit. This is part number
991381820 for an AA or AN series unit or part number 991381821 for an AN-OC series unit. Do not
complete the Inspection Sheet at the end of the CSN. A separate reply card will be provided with the
kit to document the completion of the CSN. Install the kit upon receipt.
Page 7 of 7
CSN 828
CSN 828 Elbow Leveling Sprocket Inspection Sheet
Company Name: _______________________________________________ Phone____________________________
Service Company Name:_ ________________________________________ Phone:___________________________
Company Contact: _ ________________________________________________________________________________
Company Street Address:_____________________________________________________________________________
City ______________________________________________ State:_________________ ZIP Code:_ _______________
Signature:_ ____________________________________________________
Complete this form and return to Altec to document inspection completion.
Choose one of these options.
• Online through the customer portal – Altec Connect*
Sign in or Register for an account at www.altec.com/altec-connect/
1. Select Equipment
2. Select Altec Product Notices
3. Select Report a Completed APN
• Scan and Email to product.safety@altec.com
• FAX to 1-877-659-9929
*Customer performed warranty can be submitted online for reimbursement
through Altec Connect.
To login to your existing
Altec Connect account,
scan here with your
smart phone!
Submission of this form does not order parts or schedule service from Altec.
If the customer or the customer’s warranty provider performs the repair, a warranty claim must be submitted
to be reimbursed for the cost of the parts and/or labor through Altec Connect.
For more information or to schedule the work to be done by an Altec Service technician call:
1-877-GO ALTEC (1-877-462-5832)
Make copies of this form for additional units if needed.
Model Altec Unit Serial Number Date Inspected
*
*
*
*
*
*
*
*
***************************************************************************************
2 Affected Products
Vehicles
MAKE | MODEL | YEAR |
ALTEC | AA-CLASS | 2020 |
ALTEC | AN-CLASS | 2020 |
6 Associated Documents
Defect Notice 573 Report
RCLRPT-21V548-4785.PDF 213.835KB
Recall Acknowledgement
RCAK-21V548-7072.pdf 645.634KB
ISSUED Owner Notification Letter(Part 577)
RCONL-21V548-8586.pdf 1900.107KB
Recall Quarterly Report #2, 2021-4
RCLQRT-21V548-2649.PDF 211.235KB
Recall Quarterly Report #1, 2021-3
RCLQRT-21V548-7799.PDF 211.133KB
Recall Quarterly Report #3, 2022-1
RCLQRT-21V548-3456.PDF 211.316KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=21V548&docType=RCL
- [MORE POWERFUL] Up to 135 Amp output allows you to weld mild steel up to 2/5” in the plate. Suitable for 2LB .030” & .035” flux core wire.
- [MULTI-PROCESS] 3-in-1 Welder, capable of Gasless MIG/Stick/Lift TIG. (need to buy an extra lift TIG torch) Meets your various welding needs.
- [DIGITAL DISPLAY] Advanced digital display, increases the visual clarity and improves the efficiency of the operation.
- [SYNERGIC CONTROL] When adjusting the wire feeding speed, the voltage will be automatically matched. Suitable for beginners and professionals.
- [SAFETY FIRST] Automatic compensation for voltage fluctuation, over current protection, over load protection.
- SYNERGIC CONTROL: The recommend current and wire feeding speed will be automatically matched after selected diameter of the welding wire(you can choose .030”/.035”/.040" flux core wire). The MIG welder is easier for beginners or those that are learning to weld and want to make small repairs around the house. 1 Free Flux Core Wire .030".
- 3-IN-1 WELDER: 3 welding modes Flux Core Gasless MIG/ Lift TIG/ MMA meet your different requirements (Need to buy extra Lift tig torch). Adjust the current and 10-speed variable feed controls for perfectly managed flux-cored welding of carbon steel, stainless or even thicker steel, Ideal for home DIY, outdoor repairs, rusty metal, farm and road equipment, and maintenance and repairs.
- SAFETY PROTECTION: The welder comes with an attached MIG torch and power cable, you can weld after unpacking the box, it’s convenient to use. Built-in over-current protection, over-load protection, overheating, and over-voltage function that extend the lifespan of the machine.
- PORTABLE AND COMPACT: The machine weighs only 11.79 pounds, and you can freely carry it anywhere with a handle or shoulder strap. Package includes 1* MIG130 Welder, 1* MIG Torch, 1*Ground Clamp, 1* Electronic Holder, 1* .030"/2lb Flux Cored Wire,1* 0.8/.030" conductive Nozzle,1* 0.9/.035" conductive Nozzle,1* Brush&Hammer,1* User Manual.
- WARM SERVICE & 2-YEAR WARRANTY: 30-Day Money Back Guarantee and 2-Year Warranty. Ideal for fathers day gifts. Every single of our welder machines passed various authoritative Laboratory tests in simulating extremely harsh environments before leaving our ARCCAPTAIN factory that conforms to the high standards.
- WELD ANYWHERE: Plug in the Weld-Pak 90i MIG wire feed welder anywhere 120V input power is available; It's designed to use with flux-cored welding wire (1/4” max thickness) or solid MIG wire (3/16" max thickness)
- ACCESSORIES INCLUDED: The machine comes with a full list of accessories including a welding gun, nozzle, contact tip, work cable and clamp; Metal case provides protection from the elements
- LIGHT & PORTABLE: Ideal for maintenance and mobile welders, thanks to its small and lightweight (15 lbs) inverter design and shoulder strap for portability; A good choice for professionals but it’s an easy to use welder for beginners too
- SMOOTH & EASY OPERATION: Has simple control with two knobs for wire speed and voltage; Inverter power source makes it more efficient to operate and provides smoother weld characteristics compared to traditional welders
- PERFECT FOR SMALL WELD JOBS: This machine is best for DIY projects, hobbyists, home repairs and more; Infinite welding voltage allows fine-tuning of weld characteristics
- Easy to Use: The welding machine has included with voltage control knob,wire speed adjustment knob and with synergic control, automatic change of the voltage & wire feeding speed by adjusting the amperage or choosing different thicknesses. Even beginners can use it easily.
- Powerful And Safe Machine:This 130A Welding machine can weld mild up to 3.0mm plate,equipped with overload and overheating system,feel free to use,it’s very safe.Big enough to handle 2.2 pound rolls of wire.
- Portable Design: Lightweight and compact design, with a comfortable hand grip that makes it easy to carry wherever you want; It only weighs 8.7 lbs., so you can effortlessly take it as far as you can.
- Wide Applications:It can be used with a wide variety of metals and alloys.Suitable for home users, DIY craft enthusiasts, beginners and small projects.
- Package Includes:130 MIG welding machine; Mig torch; Ground clamp; Brush&Hammer; 1lb .030" flux cored welding wire.
- Simple user interface - Seven segment display with basic knob controls.
- Process Capabilities - MIG, Flux-Cored and Spool Gun.
- Dual Input Voltage - 120V and 230V inputs so you can plug into any common power supply.
- Ergonomic Case - Sleek and robust case design with multiple lift points for ease of mobility around the shop.
- Lightweight and Portable - Only 41 lbs
- 4 in 1 Welding Machine:This is a multifunctional welding machine,suitable for MMA, Lift TIG, flux MIG, gas MIG,4 welding modes for you to choose.
- Synergic Control: Adjusting the amperage or choosing different wire thicknesses,the voltage and wire feeding speed will automatically change.Even a beginner can easily use it.
- Gas/Gasless Welding: You can choose Flux Core Wire(Gasless) or Solid Wire(Gas). This Welder Can handle 2 lb and 10 lb rolls of wire 0.8mm~1.0mm Flux Core Wire/Solid Wire, MAX Welding Thickness 8.0mm.
- Lift TIG/ARC Welding: Lift TIG available,TIG Torch fits WP17V, not included in the package.TIG Welding thickness 1.0MM-8.0MM, Suitable for thin work-pieces such as stainless steel, alloy steel, carbon steel etc.Arc Welding fits rods E6013.
- Powerful And Safe Machine:This 200A Welding machine can weld mild up to 8.0mm plate,equipped with overload and overheating system,feel free to use,it’s very safe.
- Synergic Control: The welding parameter is built-in with precise data. It will choose the voltage, amperage and feeding speed that is needed based on welder data, making it much easier for new welders.
- Multi-functions in one machine: Suitable for stick, lift TIG(torch is not included), flux MIG, gas MIG
- Powerful Machine: Up to 200A output current that can weld mild up to 5/32 inch (4.0mm) plate.
- Big enough to apply to 2 and 10 pounds rolls of wire. Ready to feed .030"(0.8mm) with solid core wire, and .035" (0.9mm)with flux core wire.Can Handle E7018 basic electrode.
- Dual voltage input design: Welding machine can be plugged into 110(120)V / 220(230)V dual voltage (Automatic fitting).
- 🛡️★Multi-Function Welding Machine: IGBT Full 20-200Amp(Max) with Digital Display for reliable quality and stable performance. Suitable for MMA, Lift TIG, Flux MIG, and Gas MIG. Big enough to handle 2 to 5 pound rolls of wire.
- 🛡️★Powerful Welding Capability: Up To 200A Output Current That Can Weld Mild Up To 5/32 Inch (4.0mm) Plate.MAX 5 Pound Rolls Of Wire.030"(0.8mm) With Solid Core Wire, And .035" (0.9mm)With Flux Core Wire.Can Handle E7018 Basic Electrode
- 🛡️★Complete Welding Kit: Includes MIG Gun(2.8M), Ground Clamp and Holder (2M), 220V to 110V Adapter, Drive Roller Wheel, Contact Tips, Gass Nozzles, and Welder Operation Manual. Processes recommended for MIG-Cast Iron, Copper, Brass, Titanium, Magnesium Alloys. Flux Cored- Aluminium, Cast Iron, Copper, Brass, Titanium.
- 🛡️★Intuitive Synergic Design: Synergic Control with automatic change of the voltage & wire feeding speed by adjusting the amperage or choosing different thicknesses. The MIG-200 is capable of true lift TIG (TIG Lift Torch not included) welding as well as stick welding.
- 🛡️★Safety Features: Automatic protection function for over-current, over-voltage, and over-heating.
- 6 in 1 Welding Machine: The multi-function welding machine included Gas/Solid Wire MIG, Gasless Flux Core MIG, Stick/MMA, Spot welding, Lift TIG, spool gun compatible (tig gun and spool gun not included,WP-17V-35,LBT150)
- MIG Synergic Control: When you selecting wire diameter and gas material,the welder will automatically match recommended current and wire feed speed.So, it’s very easy for beginners.Also, if you are experienced welder, you can adjust the welding current according to your personal welding habit.
- Can Weld Aluminum:This Multi MIG welder can weld various of metals,It can not only weld stainless steel,alloy steel,iron but also can weld aluminum.It has two ways to weld aluminum, to install the teflon wire feed tube or use spool gun.
- Wide Application:Various Welding Wire Suitable,suitable for all kinds of welding requirements .023”/.030”/.035” solid wire, .023”/.030”/.035” flux core wire,.035”/.040”/.045” aluminum wire.
- Powerful And Safe Machine:This 250A Welding machine can weld mild up to 8.0mm plate,equipped with overload / over-voltage/over-current/overheating system,feel free to use,it’s very safe.
- 【IGBT Inverter Welder】This welder can perform STICK(ARC)/MIG welding. The unique IGBT control mode improves the reliability of the welder, which can ensure good arc stability and provide smoother welding and deeper depth of melt with stable welding current for perfect welding. Perfect for beginners or professionals for small welding operations.
- 【Safe and stable welder】The welding machine is designed with 110v/220v dual voltage, stable wire feeding, good arc leading, easy to control and suitable for different welding requirements. MIG/STICK welder is also equipped with overheat protection to improve welding efficiency and ensure your safety. The high performance fan motor provides cooling function to promote the heat dissipation of the machine and prolong the service life of the machine.
- 【Portable Welder】MIG welder machine is made of high quality material, compact mini body design (12.9*6*6.5 inches, 11LBS), easy to move and store. The user-friendly handle design of the flux core welder allows you to use your welding creativity anytime and anywhere. Whether you work indoors or outdoors, the handle design allows you to carry it around and weld whenever you want.
- 【Easy to operate】The flux core welding machine is a super easy to operate 2-in-1 welder that can effectively handle iron and carbon steel welding tasks with flux cored wire sizes of 0.030" and 0.035", you can set the current range according to the thickness and characteristics of the material, with an output current of up to 140 amps and an ARC mode that supports welding of E7018 and E6013 electrodes.
- 【Big enough for wiring space】Changing wire feeders or wire feed wheels is a simple process, as is using our multi-process MIG welding machine that can handle 2 lbs of flux cored wire. In addition, the spacious interior makes handling MIG welding tasks easier. If you have any questions, please feel free to contact us.
Last update on 2024-03-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.