| “This site contains affiliate links for which OEMDTC may be compensated” |
February 24, 2020 NHTSA CAMPAIGN NUMBER: 20V103000
Limit Switch Improperly Installed
If the platform level limit switch does not stop the platform from tilting, a platform occupant could fall, increasing the risk of an injury.
NHTSA Campaign Number: 20V103
Manufacturer Terex South Dakota, Inc.
Components EQUIPMENT
Potential Number of Units Affected 407
Summary
Terex South Dakota, Inc. (Terex) is recalling certain 2014-2019 TM bucket/boom trucks. The limit switch was installed upside down and does not stop platform level movement if the platform level exceeds 15 degrees.
Remedy
Terex will notify owners, and dealers will properly install the limit switch, free of charge. The recall began April 14, 2020. Owners may contact Terex customer service at 1-605-882-4000. Terex’s number for this recall is SN681.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
| Terex Utilities | |
| SAFETY NOTICE | SN681A |
DATE: 4/6/2020
REVISED: 5/27/2020
TO: Owners, Users, Dealers, and Installers
MODELS AFFECTED: TM Aerial Devices
SUBJECT: Leveling Sensor Installation
Issue:
On Terex TM aerial devices, manufactured from February 2011 through April 2020, the basket level limit sensors at the boom tip may have been assembled in the incorrect orientation. The limit sensors prevent the platform from going more than 15 degrees from level if the electrical system malfunctions or there is damage to components. The incorrect mounting of the level sensors may cause an out of level basket to continue moving more than 15 degrees out of level. If the leveling system malfunctions it may cause the occupants to fall from the platform.
Action:
What the Owner Must Do:
The owner must inspect their equipment and correct if required within 10 days of receiving this bulletin.
- Inform all users, operators, and supervisors that the basket level sensors must be inspected within 10 days on TM aerial devices and follow the continued use section of this bulletin until the unit is corrected. This bulletin applies to TM Aerial devices with the hydraulic generator at the boom tip and applies to machines with an end mount platform or dual side mount platforms.
- Inspect the unit to determine if your unit has the incorrectly installed level sensors.
Figure 1 – Level Sensor Location on End Mount Machine
Figure 2 – Level Sensor Location on Dual Platform Machine
- Inspect the basket level sensor orientation using the below pictures for reference.
End Mount Boom Tip:
Dual Basket Boom Tip:
- If your unit has the light colored potting visible on the top sensor, or the sensor labeled A on the bottom; this bulletin applies. Correct following the instructions in Field Service Kit Z1562. Take a picture before correcting the issue and another picture after correcting the issue. Send both pictures with the completion form including the serial number and date of correction to warranty@terex.com.
- If your unit has the light colored potting visible only on the bottom sensor with the wires coming out of the sensors above the mounting screw and with sensor labeled A on top this bulletin does not apply and use can continue without restriction.
Continued Use:
- Inform the users of the content of this bulletin and remind them of the daily pre-shift inspection requirements.
- If the leveling system malfunctions and the platform gets more than 15 degrees out of level utilize one of the following procedures to stop the leveling system:
- Release the enable lever and use the manual level adjustment control to correct the level of the platform.
- From the lower controls shut off the upper controls and use the lower controls to level platform and lower boom.
- Repair issue that caused the malfunction and correct leveling sensor per the Field Service Kit Z1562 instructions.
- Always follow inspection and maintenance requirements as specified in the manuals.
What Terex will Do:
Terex will provide a Field Service Kit, Z1562, to the nearest Terex Utilities dealer or Field Service Technician for installation on your unit at no cost to the owner.
Contact Terex Utilities; through your nearest TEREX Utilities dealer as shown on the web site, terexutilities.com, call Terex Utilities Warranty Department at 1-844-837-3948 or by email at utilities.warranty@terex.com to arrange for repair within 10 days of receiving this bulletin. If you have sold the unit involved in this bulletin forward this bulletin to the new owner within 10 days and notify Terex of the serial number and contact information for the new owner.
Dealers and Installers: A letter is being sent to owners of affected units. If affected units are in your area TEREX Utilities will contact you to arrange the repairs. Affected units, as shown on the owner letter, will have the repairs performed at no charge to the owner. Labor allowance is $120.
Only TM models built with hydraulic generators at the boom tip are affected. If the owner contacts you call TEREX Utilities Warranty Department at 1-844-837-3948 for repair instructions.
Important: Some of the involved units may be in rental fleets. Federal Law requires you to complete the recall service on these units before renting, or to inform the renters within 10 days of receipt of this bulletin.
Note to Owners: If the manufacturer or their dealer has failed or is unable to remedy the defect/noncompliance condition without charge or within a reasonable amount of time you can notify:
Administrator
National Highway Traffic Safety Administration
1200 New Jersey Avenue, SE, West Building
Washington, DC 20590
Or call the toll-free DOT auto Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153; or go to https://www.safercar.gov .)
Terex and local industry standards (CSA and ANSI) requires that the purchaser of a Terex unit report to Terex the model and serial number of each machine sold, as well as the name, address, and telephone number of the new owner, within 60 days of the sale. Use the Owner Update Form in the manual to update the owner status of any of your machines. Terex also asks the seller to provide the new owner information so if you require additional copies of the Owner Update Form or have any questions, please contact TEREX Utilities Warranty Department at 1-844-837-3948 or utilities.warranty@terex.com.
Terex, OSHA and local industry standards, also require that the manufacturer’s bulletins be completed. It is your responsibility to communicate this important information to all machine owners and applicable branches. If you require additional copies of this bulletin or have any questions, please contact TEREX Utilities at 1-844-837-3948.
April 14, 2020
‘owner’
‘address1 ‘
‘city’, ‘state’ ‘zip’
IMPORTANT SAFETY RECALL 20V-103
This notice applies to your vehicle
Dear Terex Equipment Owner,
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.
Terex is recalling certain 2014-2019 TM vehicles. The limit switch was installed upside down and may not stop platform level movement if the platform level exceeds 15 degrees as intended, potentially causing uncontrollable movement.
REASON FOR NOTICE
SN681 is for the platform leveling system on Terex TM end mount aerial devices. One of the two basket level limit sensors at the boom tip may have been assembled upside down. The limit sensors prevent the platform from going more than 15 degrees from level if the electrical system malfunctions. The incorrect mounting of the level sensor may cause an out of level basket to continue moving more than 15 degrees out of level. If the leveling system malfunctions it may cause the occupants to fall from the platform, increasing the risk of an injury.
WHAT TEREX WILL DO
No parts are required to reposition the sensor if required. Terex will provide Field Service Kit Zl 562, sensor repositioning and testing instructions, and labor at no charge to the customer. Contact Terex Utilities; through your nearest TEREX Utilities dealer as shown on the web site, https://www.terex.com/utilities/en, call Terex Utilities at 1-844837-3948 or by email at utilities.warranty@terex.com to arrange for repair within 10 days of receiving this bulletin.
WHAT THE OWNER MUST DO
The owner must inspect their equipment and correct if required within 10 days of receiving this bulletin.
- Inform all users, operators, and supervisors that the basket level sensor must be inspected within 10 days on TM end mount aerial devices and follow the continued use section of this bulletin until the unit is corrected. This bulletin does not apply to units with side mount platforms.
- Inspect the unit to determine if your unit has an incorrectly installed level sensor.
- If your unit has both sensors mounted with the light colored potting visible, this bulletin applies. Correct following the instructions in Field Service Kit Zl 562. Take a picture before correcting the issue and another picture after correcting the issue. Send both pictures with the completion form including the serial number and date of correction to warranty@terex.com.
- If your unit has the light colored potting visible only on the top sensor, and the wires coming out of the sensors below the mounting screw this bulleting does not apply and use can continue without restriction.
CONTINUED USE
- Inform the users of the content of this bulletin and remind them of the daily pre-shift inspection requirements.
- If the leveling system malfunctions and the platform gets more than 15 degrees out of level utilize one of the following procedures to stop the leveling system:
- Release the enable lever and use the manual level adjustment control to correct the level of the platform.
- From the lower controls shut off the upper controls and use the lower controls to level platform and lower boom.
- Repair issue that caused the malfunction and correct leveling sensor per the Field Service Kit Zl 562 instructions.
- Always follow inspection and maintenance requirements as specified in the manuals.
If you have any questions you can find your nearest dealer at this web site; https://www.terex.com/utilities/en/products/dealer-locator/index.htm.
If you take your unit to your dealer on the agreed service date and they do not remedy this condition on that date or within three (3) working days of scheduled appointment, we recommend you contact Terex Utilities Warranty department by calling 1-800-9828975
Note to Owners: If the manufacturer or their dealer has failed or is unable to remedy the defect/noncompliance condition without charge or within a reasonable amount of time you can notify:
Administrator
National Highway Traffic Safety Administration
1200 New Jersey Avenue, SE, West Building,
Washington, DC 20590
Or call the toll-free DOT auto safety Hotline at 1-888-327-4236 (TTY: 1-800-4249153; or go to https://www.safercar.gov.)
If you have had your unit repaired for this issue prior to receipt of this notice, you may be eligible for reimbursement. For more information, please contact Terex Utilities at the above contact information.
If you have sold or retired the unit please let us know by contacting the Terex Utilities Warranty department at 1-844-837-3948 or send the serial number and new owner contact information to utilities.warranty@terex.com . Forward this Notice to the new owner within 10 days of receipt of this letter.
If you have leased this vehicle to another person, forward a copy of this notice to the lessee within ten days of your receipt of this notice.
Thank you for your immediate attention on this important matter,
Jeff Hegstrom
Product Support Manager
Our records indicate the following machines, registered to you, are involved in PN681.
| Model | Serial Number |
| ‘model’ | ‘Serial number’ |
SEOCONTENT-START
Good afternoon,
DO NOT DISSEMINATE TO END CUSTOMERS! Any dissemination to affected owners can result in $15,ooo
fine per unit. If contacted about this notice, you can speak with the customers about the issue but can’t supply them
with any other information.
On Monday the 22d we’ll be hosting a conference call to release Safety Notice 681A. This addresses a potential problem
with the positioning of the platform leveling sensors at the boom tip. NHTSA has assigned their number 20V103 to this
bulletin.
Please dispose of any of the previous Safety Notice 681 information you received. Dispose of the previous safety notice
bulletin, work instructions, and SN681 work completion form.
I’ve attached the SN681A bulletin, Z1562 FSK bill of material plus work instructions, and the SN681A work completion
form. I’ve also attached the owner lists for U.S. units, Canadian units, and export units. Note also Column K. If a
customer ordered a Z1390 FSK/TM TILT CNTRL RETROFIT as a replacement part, they are affected as well. The Z1390 FSK
included the same level sensors so the machines that they were installed on are affected by this notice as well. The
ordering customer purchase order number is listed. The projected owner letter mailing date for U.S. owners is Tuesday
the 23d. The mailing date for Canadian customers is to take place no later than the 23d also.
**********************************************************************************
‘owner’
‘address1’
‘city’, ‘state’ ‘zip’
IMPORTANT SAFETY RECALL 20V-103
This notice applies to your vehicle
Dear Terex Equipment Owner,
September 25, 2020
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle
Safety Act.
REASON FOR NOTICE
SN681A is for the platform leveling system on Terex TM aerial devices. The basket level limit sensors
at the boom tip may have been assembled in the incorrect orientation. The limit sensors prevent the
platform from going more than 15 degrees from level if the electrical system malfunctions or there is
damage to components. The incorrect mounting of the level sensors may cause an out of level basket
to continue moving more than 15 degrees out of level. If the leveling system malfunctions it may cause
the occupants to fall from the platform.
WHAT TEREX WILL DO
Terex will provide a Field Service Kit, 21562, to the nearest Terex Utilities dealer or Field Service
Technician for installation on your unit at no cost to the owner, it will take 1 hour to complete.
Contact Terex Utilities; through your nearest TEREX Utilities dealer as shown on the web site,
terexutilities.com, call Terex Utilities Warranty Department at 1-844-837-3948 or by email at
utilities.warranty@terex.com to arrange for repair within 10 days of receiving this bulletin. If you have
sold the unit involved in this bulletin forward this bulletin to the new owner within 10 days and notify
Terex of the serial number and contact information for the new owner.
WHAT THE OWNER MUST DO
The owner must inspect their equipment and correct if required within 10 days of receiving this bulletin.
1. Inform all users, operators, and supervisors that the basket level sensors must be inspected
within 10 days on TM aerial devices and follow the continued use section of this bulletin until the
unit is corrected. This bulletin applies to TM Aerial devices with the hydraulic generator at the
boom tip and applies to machines with an end mount platform or dual side mount platforms.
2. Inspect the unit to determine if your unit has the incorrectly installed level sensors.
3. If your unit has the light colored potting visible on the top sensor, or the sensor labeled A on the
bottom; this bulletin applies. Correct following the instructions in Field Service Kit 21562. Take
a picture before correcting the issue and another picture after correcting the issue. Send both
pictures with the completion form including the serial number and date of correction to
utilities. warranty@terex.com.
4. If your unit has the light colored potting visible only on the bottom sensor with the wires coming
out of the sensors above the mounting screw and with sensor labeled A on top this bulletin does
not apply and use can continue without restriction.
Terex South Dakota, Inc.
3140 15th Avenue SE
Watertown, SD 57201 USA
1-844-837-3948
CONTINUED USE
1. Inform the users of the content of this bulletin and remind them of the daily pre-shift inspection
requirements.
2. If the leveling system malfunctions and the platform gets more than 15 degrees out of level
utilize one of the following procedures to stop the leveling system:
a. Release the enable lever and use the manual level adjustment control to correct the level of
the platform.
b. From the lower controls shut off the upper controls and use the lower controls to level
platform and lower boom.
c. Repair issue that caused the malfunction and correct leveling sensor per the Field Service
Kit Z1562 instructions.
3. Always follow inspection and maintenance requirements as specified in the manuals.
If you have any questions you can find your nearest dealer at this web site;
https://www.terex.com/utilities/en/products/dealer-locator/index.htm.
If you take your unit to your dealer on the agreed service date and they do not remedy this condition on
that date or within three (3) working days of scheduled appointment, we recommend you contact Terex
Utilities Warranty department by calling 1-800-982-8975.
Note to Owners: If the manufacturer or their dealer has failed or is unable to remedy the
defect/noncompliance condition without charge or within a reasonable amount of time you can notify:
Administrator
National Highway Traffic Safety Administration
1200 New Jersey Avenue, SE, West Building,
Washington, DC 20590
Or call the toll-free DOT auto Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153; or go to
https://www.safercar.gov.)
If you have had your unit repaired for this issue prior to receipt of this notice, you may be eligible for
reimbursement. For more information, please contact Terex Utilities at the above contact information.
If you have sold or retired the unit please let us know by contacting the Terex Utilities Warranty
department at 1-844-837-3948 or send the serial number and new owner contact information to
utilities.warranty@terex.com . Forward this Notice to the new owner within 10 days of receipt of this
letter.
If you have leased this vehicle to another person, forward a copy of this notice to the lessee within ten
days of your receipt of this notice.
Thank you for your immediate attention on this important matter,
Jeff Hegstrom
Product Support Manager
Our records indicate the following machines, registered to you, are involved in SN681A.
Model Serial Number
‘model’ ‘Serial number’
****************************************************************************************
‘owner’
‘address1’
‘city’, ‘state’ ‘zip’
IMPORTANT SAFETY RECALL 20V-103
This notice applies to your vehicle
Dear Terex Equipment Owner,
December 29, 2020
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle
Safety Act.
REASON FOR NOTICE
SN681A is for the platform leveling system on Terex TM aerial devices. The basket level limit sensors
at the boom tip may have been assembled in the incorrect orientation. The limit sensors prevent the
platform from going more than 15 degrees from level if the electrical system malfunctions or there is
damage to components. The incorrect mounting of the level sensors may cause an out of level basket
to continue moving more than 15 degrees out of level. If the leveling system malfunctions it may cause
the occupants to fall from the platform.
WHAT TEREX WILL DO
Terex will provide a Field Service Kit, Z1562, to the nearest Terex Utilities dealer or Field Service
Technician for installation on your unit at no cost to the owner, it will take 1 hour to complete.
Contact Terex Utilities; through your nearest TEREX Utilities dealer as shown on the web site,
terexutilities.com, call Terex Utilities Warranty Department at 1-844-837-3948 or by email at
utilities.warranty@terex.com to arrange for repair within 10 days of receiving this bulletin. If you have
sold the unit involved in this bulletin forward this bulletin to the new owner within 10 days and notify
Terex of the serial number and contact information for the new owner.
WHAT THE OWNER MUST DO
The owner must inspect their equipment and correct if required within 10 days of receiving this bulletin.
1. Inform all users, operators, and supervisors that the basket level sensors must be inspected
within 10 days on TM aerial devices and follow the continued use section of this bulletin until the
unit is corrected. This bulletin applies to TM Aerial devices with the hydraulic generator at the
boom tip and applies to machines with an end mount platform or dual side mount platforms.
2. Inspect the unit to determine if your unit has the incorrectly installed level sensors.
3. If your unit has the light colored potting visible on the top sensor, or the sensor labeled A on the
bottom; this bulletin applies. Correct following the instructions in Field Service Kit Z1562. Take
a picture before correcting the issue and another picture after correcting the issue. Send both
pictures with the completion form including the serial number and date of correction to
utilities.warranty@terex.com.
4. If your unit has the light colored potting visible only on the bottom sensor with the wires coming
out of the sensors above the mounting screw and with sensor labeled A on top this bulletin does
not apply and use can continue without restriction.
Terex South Dakota, Inc.
500 Oakwood Road
Watertown, SD 57201 USA
1-844-837-3948 • Fax 1-605-882-1842
CONTINUED USE
1. Inform the users of the content of th is bulletin and remind them of the daily pre-shift inspection
requirements.
2. If the leveling system malfunctions and the platform gets more than 15 degrees out of level
utilize one of the following procedures to stop the leveling system:
a. Release the enable lever and use the manual level adjustment control to correct the level of
the platform.
b. From the lower controls shut off the upper controls and use the lower controls to level
platform and lower boom.
c. Repair issue that caused the malfunction and correct leveling sensor per the Field Service
Kit Z1562 instructions.
3. Always follow inspection and maintenance requirements as specified in the manuals.
If you have any questions you can find your nearest dealer at this web site;
https://www. terex. com/utilities/en/products/dealer-locator/index. htm.
If you take your unit to your dealer on the agreed service date and they do not remedy th is condition on
that date or within three (3) working days of scheduled appointment, we recommend you contact Terex
Utilities Warranty department by calling 1-800-982-8975.
Note to Owners: If the manufacturer or their dealer has failed or is unable to remedy the
defect/noncompliance condition without charge or within a reasonable amount of time you can notify:
Administrator
National Highway Traffic Safety Administration
1200 New Jersey Avenue, SE, West Building,
Washington , DC 20590
Or call the toll-free DOT auto Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153; or go to
https://www.safercar.gov.)
If you have had your unit repaired for this issue prior to receipt of th is notice, you may be eligible for
reimbursement. For more information, please contact Terex Utilities at the above contact information.
If you have sold or retired the unit please let us know by contacting the Terex Utilities Warranty
department at 1-844-837-3948 or send the serial number and new owner contact information to
utilities.warranty@terex.com . Forward this Notice to the new owner within 10 days of receipt of this
letter.
If you have leased this vehicle to another person, forward a copy of this notice to the lessee within ten
days of your receipt of this notice.
Thank you for your immediate attention on this important matter,
Jeff Hegstrom
Product Support Manager
Our records indicate the following machines, registered to you , are involved in SN681A.
Model Serial Number
‘model’ ‘Serial number’
**************************************************************************************************
END MOUNT BOOM TIP
REMOVE COVER
TILT CONTROL SENSOR ASSEMBLY
SWITCH “B”
REVISIONS
REV DESCRIPTION ECN DATE CHG APP
A ORIGINAL 77629 1/28/20 JKM JKM
B CHANGED TEST 78589 4/27/20 JKM JKM
C ADD SPACER AND INSTRUCTIONS 78644 5/11/20 JKM JKM
1) REMOVE COVER OVER TILT CONTROL SENSOR ASSEMBLY.
2) INSPECT TILT SWITCH MOUNTING. TAKE A “BEFORE” PHOTO OF THE SENSOR MOUNTING
AND INCLUDE WITH COMPLETION FORM.
3) LOCATE THE “A” SWITCH AND “B” SWITCH. EACH SWITCH SHOULD BE LABELED WITH
WHITE MARKER WITH THE LETTER “A” OR “B”. IF NOT, REFER TO THE TESTING SHEET TO
DETERMINE THE “A” SWITCH AND “B” SWITCH.
4) REMOVE SWITCHES.
5) POSITION THE “B” SWITCH AS THE BACK SWITCH (SWITCH MOUNTED DIRECTLY TO THE
MOUNTING PLATE) WITH THE PURPLE POTTING MATERIAL FACING OUT AWAY FROM THE
MOUNTING PLATE.
6) POSITION THE “A” SWITCH AS THE FRONT SWITCH (SWITCH MOUNTED ON TOP OF THE “B”
SWITCH) WITH THE PURPLE POTTING MATERIAL FACING IN TOWARDS THE MOUNTING
PLATE. USE SPACERS PROVIDED TO SPACE THE “A” SWITCH OUT FROM THE MOUNTING
PLATE.
DO NOT OVERTIGHTEN THE SWITCH MOUNTING BOLTS. THE “B” SWITCH MIGHT HAVE SOME
CRACKING IN THE BLACK PLASTIC HOUSING, IT CAN STILL BE USED PROVIDED THAT THE
SWITCH CAN STILL BE SECURL Y FASTENED AND THE UNIT PASSES THE TESTING PORTION
OF THIS INSTRUCTIONAL SHEET.
7) SEE PAGE 2
CORRECT
PURPLE POTTING MATERIAL IS FACING AWAY FROM MOUNTING
PLATE ON BACK SWITCH “B”. PURPLE POTTING MATERIAL IS
FACING TOWARD MOUNTING PLATE ON FRONT SWITCH “A”. CABLE
ABOVE THE MOUNTING HOLE ON BOTH SWITHES.
SWITCH “A”
INCORRECT
THIS DRAWING, WRITTEN DESCRIPTION OR SPECIFICATION REPRESENTS
TEREX SOUTH DAKOTA, INC AND SHALL NOT BE RELEASED, DISCLOSED, USED,
NOR DUPLICATED WITHOUT THE WRITTEN PERMISSION OF TEREX SOUTH DAKOTA, INC
SIMILAR TO: N/A
SEE 603948 FOR WELD REQUIREMENTS, UNLESS OTHERWISE NOTED.
ALL DIMENSIONS ARE IN INCHES DO NOT SCALE THIS DRAWING WORK
UNLESS OTHERWISE STATED TO FIGURES BREAK ALL SHARP
3RD ANGLE PRJECTION CORNERS UNLESS OTHERWISE SPECIFIED -E3- TOLERANCE UNLESS .X ±.060
OTHERWISE SPECIFIED: .XX ±.030
ANGLES: ±2°
WELDMENTS: ±.060 .XXX ±.010
BOTH SWITCHES MOUNTED
INCORRECTLY. PURPLE
POTTING MATERIAL IS FACING
OUT ON BOTH SWITCHES,
SWITCH “A” IS BACK AND
SWITCH “B” IS FRONT.
1 627436 SPACER REF
ITEM PART NO PART NAME QTY
~TER 9158496 C
1 OF 3
PART NAME: FSK INSTRUCTIONS
PRODUCT: TM ASSY:9158496 MASS:
MATERIAL: STOCK SIZE:
DRAWN BY: JKM DATE: 1/28/20 SCALE: FORM#3469B
DUAL PLATFORM BOOM TIP
DRILL HOLES IN SWITCH MOUNTING
PLATE IF SWITCHES ARE MOUNTED
INCORRECTLY
DRILL 2 – 0.22
HOLES 0.50″
LOWER 0.22
0.50
0
0
0
0
0
0
0
Cl
REMOVE COVER
0
0
0
0.50
0 0.18 ORI LL 2 – 0.18
HOLES 0.50″
LOWER
0 0
SWITCH “A” ——…
SWITCH “B”
0
0 0
CORRECT
THIS DRAWING, WRITTEN DESCRIPTION OR SPECIFICATION REPRESENTS
TEREX SOUTH DAKOTA, INC AND SHALL NOT BE RELEASED, DISCLOSED, USED,
NOR DUPLICATED WITHOUT THE WRITTEN PERMISSION OF TEREX SOUTH DAKOTA, INC
SIMILAR TO: N/A
SEE 603948 FOR WELD REQUIREMENTS, UNLESS OTHERWISE NOTED.
ALL DIMENSIONS ARE IN INCHES DO NOT SCALE THIS DRAWING WORK
UNLESS OTHERWISE STATED TO FIGURES BREAK ALL SHARP
3RD ANGLE PRJECTION CORNERS UNLESS OTHERWISE SPECIFIED
TOLERANCE UNLESS
OTHERWISE SPECIFIED:
ANGLES: ±2°
WELDMENTS: ±.060
X ±.060
.XX ±.030
.XXX ±.010
0 0
0 0
INCORRECT
~TER 9158496
20F3
C
PART NAME: FSK INSTRUCTIONS
PRODUCT: TM ASSY:9158496 MASS:
MATERIAL: STOCK SIZE:
DRAWN BY: JKM DATE: 1/28/20 SCALE: FORM# 3469B
DISCONNECT CABLE 7) TAKE AN “AFTER” PHOTO OF THE SENSOR MOUNTING AND INCLUDE WITH COMPLETION FORM.
SERVO VALVE 8) REMOVE COVER OVER LEVEL CONTROL BOX AND SERVO VALVE.
TEST
TOP VIEW OF SERVO VALVE 1) LOCATE THE SERVO VALVE AND DISCONNECT THE ELECTRICAL CABLE.
2) LOCATE THE LEVEL CONTROLLER.
MANUALLEVER o.,..__ _.. ……..,,o
3) LOCATE PIN A4, A6, A7, B1, AND B2.
4) LOCATE YELLOW WIRE WITH TAPED END. REMOVE TAPE AND INSERT YELLOW WIRE INTO THE MIDDLE FUSE PANEL.
THE LEVEL CONTROLLER LED WILL TURN ON FLASHING GREEN
MANUAL LEVER. MOVE SIDE
TO SIDE ONLY.
0 0
MOVE SIDE TO SIDE ONLY
5) SWITCH “A” IS WIRED TO A6 AND SWITCH “B” IS WIRED TO A7
6) CONNECT THE POSTIVE LEAD OF A VOLTAGE METER TO PIN A6 AND THE NEGATIVE LEAD TO PIN A4. DO NOT
DISCONNECT THE WIRES IN PIN A4 AND A6.
7) ENABLE THE SINGLE STICK AND MANUALLY LEVEL DOWN (DUMP) THE PLATFORM BY MOVING THE MANUAL LEVER
ON THE SERVO VALVE SIDE TO SIDE. DO NOT LIFT UP ON MANUAL LEVER ON SERVO VALVE OR THE LEVER COULD
BREAK.
8) VERIFY THERE IS 12 VOLTS ACROSS PIN A4 AND PIN A6 WHEN THE PLATFORM IS MORE THAN 10 DEGREES DOWN.
9) CONNECT THE POSTIVE LEAD OF A VOLTAGE METER TO PIN A7 AND THE NEGATIVE LEAD TO PIN A4. DO NOT
DISCONNECT THE WIRES IN PIN A4 AND A7.
10) ENABLE THE SINGLE STICK AND MANUALLY LEVEL UP (TIP UP) THE PLATFORM BY MOVING THE MANUAL LEVER ON
THE SERVO VALVE SIDE TO SIDE.
11) VERIFY THERE IS 12 VOLTS ACROSS PIN A4 AND PIN A7 WHEN THE PLATFORM IS MORE THAN 10 DEGREES UP.
LEVEL CONTROLLER
12) ENABLE THE SINGLE STICK AND MANUALLY LEVEL THE PLATFORM WITH THE MANUAL LEVER ON THE SERVO VALVE
TO ZERO DEGREES. CONNECT B1 AND B2 (RE-ZERO LEVEL) TERMINALS TOGETHER WITH A FLAT BLADE SCREWDRIVER
FOR 5 SECONDS. LEVEL CONTROLLER LED WILL TURN RED AND THEN BACK TO FLASHING GREEN.
LEVEL CONTROLLER LED
A4 GROUND
A6 SWITCH “A” ~
A 7 SWITCH “B” ~
A
A1
A2
A3
A4
AS
A6
A7
A8
0
(Q) (]I)
0
B1
B2
B3
B4
BS
B6
B7
B8
13) DISCONNECT THE YELLOW WIRE FROM THE FUSE PANEL AND TAPE END OF YELLOW WIRE.
YELLOW WIRE 14) RE-CONNECT ALL CABLES. VERIFY THE YELLOW WIRE IS DISCONNECTED FROM THE FUSE PANEL AND THE LEVEL
CONTROLLER LED IS OFF.
0 15) INSTALL COVERS.
(]I)
• e
D
BLACK COLORED
HOUSING
FUSE PANEL
(]I)
0
B1 RE-ZERO LEVEL
B2 RE-ZERO LEVEL
CABLE ABOVE
MOUNTING HOLE
PURPLE COLORED
POTTING MATERIAL
0
SWITCH II B”
SWITCH “A”
,_____ CABLE ABOVE
MOUNTING HOLE
THIS DRAWING, WRITTEN DESCRIPTIO’J OR SPECIFICATION REPRESENTS
TEREX SOUTH DAKOTA, INC AND SHALL NOT BE RELEASED, DISCLOSED, USED,
NOR DUPLICATED WITHOUT THE WRITTEN PERMISSIO’J OF TEREX SOUTH DAKOfA, INC
SIMILAR TO: N/A
SEE 603948 FOR WELD REQUIREMENTS, UNLESS OTHERWISE NOTED.
ALL DIMENSIONS ARE IN INCHES DO NOT SCALE THIS DRAWING WORK
UNLESS OTHERWISE STATED TO FIGURES BREAK ALL SHARP
3RD ANGLE PRJECTION CORNERS UNLESS OTHERWISE SPECIFIED E3- TOLERANCE UNLESS .X ±.060
OTHERWISE SPECIFIED:
ANGLES ±2° .XX ±.030
WELDMENTS: ±.060 .XXX ±.010
1
~TEREX. 9158496 C
30F3
PART NAME: FSK INSTRUCTIONS
PRODUCT: TM ASSY: 9158496 MASS:
MATERIAL: STOCK SIZE:
DRAWN BY: JKM DATE: 1/28/20 SCALE: FORM#3469B
*******************************************************************************************
Terex Utilities Service Network
0
C.c;,~
Hawaii {;>
Terex Utilities
Seattle 206. 764.5025 I I North Little Rock 501.945.61 ool I Bourbon 574.342.0086
7829 South 2016th Street 309 Dixie Street 4470 Lincoln Hwy West
Kent, WA 98032 North Little Rock, AR 72114 Bourbon, IN 46504
Portland 503.620.0611 I I Birmingham 205.841.6411 l ( Waukesha 262.547.8500
12805 SW 77th Place 4120 Lewisburg Rd N4W22610 Bluemound Rd
Tigard, OR 97223 Birmingham, AL 35207 Waukesha, WI 53186
Stockton 209.242. 1104 I I White House 615.672.4911 1 f Shakopee 952.445.1555
2610 Lycoming Street 200 Edenway Dr 12565 Hwy 41 Frontage Rd
Stockton, CA 95206 White House, TN 37189 Shakopee,MN 55379
Fontana 909.565.1234 I I Charlotte 704.654.3903 1 [ Watertown 605.882.3004
8594 Cherry Avenue 11945 Goodrich Drive 190114th Avenue NW
Fontana, CA 92335 Charlotte, NC 28273 Watertown, SD 57201
Phoenix 602.256.01627 I Glen Allen 804.752.2811 l ( Denver 303.202.0304
4920 W. Magnolia Street 11072 Washington Hwy 6295 E. 56th Avenue
Phoenix, AZ 85043 Glen Allen, VA 23059 Commerce City, CO 80022
,_
Fort Worth 817.698.8005 I I Lancaster 717.650.1044 l (F ield Service 800.292.1931
1300 S. Sylvania Avenue 180 N. Donnerville Rd, Suite B
Fort Worth, TX 76111 Mountville, PA 17554
San Antonio 210.476.7777 I f Medina 330.122.6900 l
142 Gembler Rd 1175 Industrial Parkway
San Antonio, TX 78219 Medina, OH 44256
Revision 3/201Q
Terex Utilities Service Center
Distributors
D Commercial Truck Equipment
D Wajax Equipment
D James A. Kiley Co.
Ring Power Corp.
Distributors
Commercial Truck an.915.9140
11199 48 St SE
Calgary, AB T2C 5H4, Canada -Wajax Equipment 519.893.2942
815 Trillium Drive
Kitchener, ON N2R 1J9, Canada
Wajax Equipment 450.682.3737
2000 Rue John-Molson
Laval, Quebec H7T 0H4, Canada
Wajax Equipment 902.468.7352
151 Thornhill Drive
Dartmouth, NS B3B 1 S2, Canada
James A. Kiley Co. 617.776.0344
15 Linwood Street
Somerville, MA 02143-2188
r, IUqhll’U Co. IM.731.1131
500 World Commerce Pkwy
St. Augustine, FL 32092
SEOCONTENT-END
6 Affected Products
Vehicle
| MAKE | MODEL | YEAR |
| TEREX | TM-SERIES | 2014-2019 |
14 Associated Documents
ISSUED Owner Notification Letter(Part 577)
RCONL-20V103-2493.pdf 1055.261KB
Loading...
Reload document 
Open in new tab
Safety Bulletin
RCSB-20V103-7476.pdf 1411.699KB
Loading...
Remedy Instructions and TSB
Loading...
Safety Bulletin
RCSB-20V103-7561.pdf 1019.522KB
Loading...
Recall Acknowledgement
RCAK-20V103-6731.pdf 245.266KB
Loading...
Defect Notice 573 Report
RCLRPT-20V103-3601.PDF 212.847KB
Loading...
Recall 573 Report- Amendment 1
RCLRPT-20V103-5747.PDF 214.021KB
Loading...
ISSUED Owner Notification Letter(Part 577)
RCONL-20V103-6696.pdf 578.541KB
Loading...
ISSUED Renotification Notice
RCRN-20V103-0833.pdf 6673.982KB
Loading...
Manufacturer Notices(to Dealers,etc)
RCMN-20V103-0208.pdf 1013.897KB
Loading...
Recall Quarterly Report #3, 2020-4
RCLQRT-20V103-8052.PDF 211.328KB
Loading...
ISSUED Renotification Notice
RCRN-20V103-6349.pdf 7047.752KB
Loading...
Recall Quarterly Report #2, 2020-3
RCLQRT-20V103-4284.PDF 211.236KB
Loading...
Recall Quarterly Report #1, 2020-2
RCLQRT-20V103-6623.PDF 211.142KB
Loading...
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V103&docType=RCL
| “This site contains affiliate links for which OEMDTC may be compensated” |
- 🧰UPGRADE ACCESSORIES:Our 4 point adjustment full body harness is international version which is signed according to the highest standards in world.It adds many safe and practical accessories: this harness has as many as 4 adjustm-ent points; shoulder load-bearing loops allow you to enhance suspension protection in tight spaces; the waist of the harness has durable side D-rings can be used in work positioning to and store more spare hooks！
- 🧰SAFETY STANDARD:This full body construction harness is the perfect roofing harness specifically designed with premier fall arrest gear.We exceeded expectations by meeting and surpassing the requirements set forth in the ANSI/ASSE Z359.11-2014 standard.This complete fall protection package includes a 2m long safety lanyard and is also compatible with other types of lanyards.We offer unmatched safety harness fall protection!Safety is our number one priority!
- 🧰LIGHTWEIGHT & COMFORT: Ergonomic, our new patented waist padding upgrades with thick premium ventilated breathable mesh plush pads minimize muscle fatigue.Increased air flow provides faster cooling and drying,providing additional comfort for the waist.Constructed with extra-wide support belt with premium plush padding for major support, soothing comfort and lateral movements.TRSMIMA harness for construction workers will never let you "down"!
- 🧰RELIABLY DURABLE:Our safety harness strap is made of 100% premium high strength industrial synthetic polyester fibers, which has great performance in abrasion and heat resistance.We commit that all stitching of the webbing are intact after successive tearing test in different angles at force of 25KN!.Our 4-point full body harness designed to accommodate both men and women. Waist size: 78-143cm(30.7inch-55.3inch) Leg size: 54-97cm(21.2inch-38inch), fit weigh 130-350 pounds (59 to 159 kg)
- 🧰OSHA COMPLIANT – TRSMIMA ensures the safety and well-being of workers through setting standards and offering training, outreach, education, and assistance. Great for use in Construction, Demolition, Climbing, Hunting, Roofing, Emergency, First responder, Landscaping, Security and etc.
- ✅COMFORT – Designed with reinforced edges for added comfort and relief. Water-wicking material averts the harness from sweat and water deterioration. Harness is designed to allow for better lateral movements.
- ✅RELIABLE – Standout and be easily spotted with our high-visibility green harness. Alloy steel D-ring ensures all weather performance preventing corrosion against all weather conditions. Rugged construction endures rough use, standing up to long periods of outdoor elements including sun exposure without tearing or fraying for added longevity.
- ✅SAFE – The AFP 6 FT Internal Shock Absorbing Lanyards are made with lightweight, heavy-duty, high-strength outer polyester webbing and a polyester core specially sewn in to reduce impact forces, with two substantially secure heavy-duty double-locking gates.
- ✅DURABLE – The tough webbing is highly resistant to abrasion, aging, and won’t soften from frequent use. This webbing has low shrink properties and a high temperature threshold.
- ✅CONVENIENT – Our most popular 2-in-1 fall arrest lanyards that minimizes trip hazards or fall with a shock absorber built into the lanyard, eliminating the need for an additional bulky shock pack. Elasticated leg expands from 4-1/2 to 6 feet and can resist 8,500 lbs. of tensile strength!
- 🧰UPGRADE ACCESSORIES:Our 4 point adjustment full body harness is international version which is signed according to the highest standards in world.It adds many safe and practical accessories: this harness has as many as 4 adjustm-ent points; shoulder load-bearing loops allow you to enhance suspension protection in tight spaces; the waist of the harness has durable side D-rings can be used in work positioning to and store more spare hooks！
- 🧰SAFETY STANDARD:This full body construction harness is the perfect roofing harness specifically designed with premier fall arrest gear.We exceeded expectations by meeting and surpassing the requirements set forth in the ANSI/ASSE Z359.11-2014 standard.This complete fall protection package includes a 2m long safety lanyard and is also compatible with other types of lanyards.We offer unmatched safety harness fall protection!Safety is our number one priority!
- 🧰LIGHTWEIGHT & COMFORT: Ergonomic, our new patented waist padding upgrades with thick premium ventilated breathable mesh plush pads minimize muscle fatigue.Increased air flow provides faster cooling and drying,providing additional comfort for the waist.Constructed with extra-wide support belt with premium plush padding for major support, soothing comfort and lateral movements.TRSMIMA harness for construction workers will never let you "down"!
- 🧰RELIABLY DURABLE:Our safety harness strap is made of 100% premium high strength industrial synthetic polyester fibers, which has great performance in abrasion and heat resistance.We commit that all stitching of the webbing are intact after successive tearing test in different angles at force of 25KN!.Our 4-point full body harness designed to accommodate both men and women. Waist size: 78-143cm(30.7inch-55.3inch) Leg size: 54-97cm(21.2inch-38inch), fit weigh 130-350 pounds (59 to 159 kg)
- 🧰OSHA COMPLIANT – TRSMIMA ensures the safety and well-being of workers through setting standards and offering training, outreach, education, and assistance. Great for use in Construction, Demolition, Climbing, Hunting, Roofing, Emergency, First responder, Landscaping, Security and etc.
![KwikSafety - Charlotte, NC - SCORPION Safety Harness [w/attached 6ft. Tubular Lanyard on back] OSHA ANSI Fall Protection INTERNAL Shock Absorbing Lanyard/Construction Carpenter Scaffolding](https://m.media-amazon.com/images/I/51uatJjjfxL._SL160_.jpg)
- FALL PROTECTION GEAR - The KwikSafety SCORPION is a durable, heavy duty, high performance Full Body Harness that meets and exceeds ANSI/ASSE Z359.11-2014 standards. Our harness fall protection is the complete support package because the SCORPION includes a fall protection safety lanyard! The harness is also compatible with other lanyards with shock absorbers, roof lifelines, and anchorage tether lanyards. Safely perform the job knowing the SCORPION fall protection harness has your back!
- HEAVY DUTY D-RING - One back dorsal ring is all it takes to provide functionality on the construction job. The dorsal ring is used for fall arrest & can be used for travel restraint or rescue. The pass-through buckles on our universal harness are made out of synthetic material that is superior to polyester. For some jobs, more fall prevention accessories may be necessary. If an anchor point is needed, like a roofers anchor point or scaffold cross arm strap, we have kits and combos available!
- OSHA COMPLIANT - This construction harness is an essential part to any workers positioning system & is ideal for any job where OSHA compliance is required. This full body harness supports users within the capacity range of 130 - 310LBS (59 to 140 kg), 4’10” to 6’6” (147 to 198 centimeters) due to the adjustment points. To ensure your harnesses properly fit, see that all buckles are connected, leg & shoulder straps are snug, & chest straps are in the center of the chest area.
- FALL PROTECTION HARNESS - Safety harnesses are crucial PPE used in various industries to prevent falls & injuries. They consist of adjustable straps, buckles, & attachment points designed to secure a worker to an anchor point. When properly worn & connected, safety harnesses distribute the force of a fall across the body, reducing the risk of serious injury. Safety harnesses are necessary for workers in construction, roofing & other high-risk occupations.
- THE SAFETY YOU NEED, THE STYLE YOU WANT - Safety harnesses offer a secure fit for users of all shapes & sizes, ensuring both safety & peace of mind. Harnesses play a vital role in mitigating the risks associated w/ working or engaging in activities at elevated heights. The proper use of safety harnesses significantly reduces the risk of accidents or injuries, and regular inspections ensure harnesses remain in optimal condition, providing reliable protection for workers operating at heights.
- ✅COMFORT – Upgraded thick premium vented breathable mesh plush pads for added comfort delivering relief to shoulders, legs, and back. Reinforced soft edges foam shoulder pads prevent skin from chafing. Water-wicking material averts the harness from sweat build-up and water breakage. Constructed with extra-wide 8’’ back support belt with premium plush padding for major support, soothing comfort and lateral movements. 5 adjustment points on the padded shoulders, padded legs, and chest.
- ✅LIGHTWEIGHT & CONVENIENT – Stand out with hi-viz lime stitching webbing throughout the harness. Endures rough use, standing up to long periods of the outdoors including sun without corrosion, tearing or fraying for added longevity. Quick-Release buckles on the chest and spring activated shoulder adjuster. Convenient buckle strap on shoulder pad to hold cell phone, lanyards, walkie-talkies. Side D-rings allows use of both hands. Fixed D-ring reduces constant readjustments and stays in position.
- ✅RELIABLE – Upgraded braided webbing designed with a high-tension stitching pattern for maximum visibility, security and a tensile strength of over 5,000 lbs! Tough webbing is highly resistant to abrasion, aging, and will not soften from frequent use. Thick sturdy belt for tool bag carrying convenience. Durable lanyard keepers on both straps for easy parking of hooks and carabiners. Equipped with a new molded “easy-link” SRL adapter technology, which allows for easy SRL attachments.
- ✅PERFORMANCE – Harness is designed for a maximum capacity of 310lbs, including the worker's body weight, clothing, tools and other accessories. Meets ANSI Z359.11; and OSHA 1910.140 and 1926.502. D-rings conform to EN361-2002. We rigorously test all our Fall Protection safety products to ensure they meet global industry standards established by OSHA, MSHA, ANSI, CSA and CE. Our ISO 9001-2008 certification and on-site ISO 17025-accredited lab demonstrates our commitment to quality and safety.
- ✅SAFE – When you're working at height, you need to be able to trust your personal protective equipment, not only for your sake, but for the sake of your co-workers below. AFP Fall Protection elevates worker safety to new heights with quality products, people and service. With harnesses designed to comply with industry standards and adapt to the needs of today's workforce, we're committed to making products that help employers bring workers home safely.
- ✅UPGRADE ACCESSORIES:Our full body harness is international version which is designed according to the highest standards in world.It adds many safe and practical accessories: this harness has as many as 4 quick release buckles; shoulder load-bearing loops allow you to enhance suspension protection in tight spaces; chest attachment points improve safety when you climb high (such as poles); the chest of the harness has extra hanging loops to help you store more spare hooks！
- ✅CERTIFIED with Both OSHA and ANSI:This full body construction harness is the perfect roofing harness specifically designed with premier fall arrest gear.The compliancy guidelines met include: ANSI Z359.11-2014, ANSI A10.32-12, OSHA 1926 Subpart M, OSHA 1910. We offer unmatched safety harness fall protection!Safety is our number one priority !The Trsmima System exceeds the already-rigorous ANSI testing standards and is heavy-duty, high-performance fall protection you can trust to have your back.
- ✅LIGHTWEIGHT & COMFORT: Ergonomic, our new patented shoulder, leg, and back padding upgrades with thick premium ventilated breathable mesh plush pads minimize overhead muscle fatigue.Increased air flow provides faster cooling and drying,providing additional comfort for the shoulders, legs and back.Constructed with extra-wide 8''back support belt with premium plush padding for major support, soothing comfort and lateral movements.TRSMIMA harness for construction workers will never let you "down"!
- ✅RELIABLY DURABLE:Our safety harness strap is made out of 100% premium high strength industrial synthetic polyester fibers, which has great performance in abrasion and heat resistance.We commit that all stitching of the webbing are intact after successive tearing test in different angles at force of 25KN!Proper fit is essential for convenience in work at height, our harness safety offers 6 adjustm-ent points for users to ensure proper fit within the weight capacity range of 130 to 350 pounds !
- ✅SAFE:TRSMIMA cannot tolerate any defective product outgoing factory.We focus on servicing the industrial and residential contractors to the weekend DIY warrior with our brand TRSMIMA in rope, personal protective equipment and fall protection.Customer service and satisfaction is the key to our success by delivering great products quickly and at reasonable prices!
![KwikSafety - Charlotte, NC - SUPERCELL Safety Harness [2 PACK] Premium Shoulder Padding ANSI OSHA Full Body Fall Protection Work Equipment Construction Tower Climbing Roofing Forklift Aerial Boom Lift](https://m.media-amazon.com/images/I/517Z2tocDIL._SL160_.jpg)
- 3 HEAVY DUTY D-RINGS | SHOULDER PAD SUPPORT - The KwikSafety SUPERCELL is a premium, durable, high performance full body harness that meets & exceeds ANSI/ASSE Z359.11-2014 standards. Our safety harness fall protection features: (2) hip d-rings & (1) dorsal d-ring for fall arrest attachment, travel restraint & rescue, (2) cushioned shoulder pads, (1) pass-through buckles & (2) tongue buckles to ensure proper fit, & premium stitched load bearing straps made from a non-recycled synthetic material.
- FREE TOOL LANYARD & BAG - Fall arrest harness d ring harness made of 100% polyester quality stitched yellow & black aerial lift harness straps. Correct fitting construction harness is essential for proper performance for men & women. Supports users within the capacity range of 130-310Ibs (59-140kg), 4'10"-6'6" (147-198cm). To ensure your fall arrest safety harnesses fit properly, see that all buckles are connected, leg & shoulder straps are snug & chest straps are in the center of the chest.
- OSHA APPROVED SAFETY HARNESS - The best construction body harness for those who need safety first but want premium product & style. Fall protection body harness men ideal use: construction harnesses, climbing harness, ironworkers harness, roofing harness, construction harness women, rescue chest harness, security harness, forklift harness, safety harness lineman & harness tower climbing. Mens harness also for high-rise window cleaning, gutter cleaning, painting harness & search/rescue.
- FALL PROTECTION HARNESS - Safety harnesses are crucial PPE used in various industries to prevent falls & injuries. They consist of adjustable straps, buckles, & attachment points designed to secure a worker to an anchor point. When properly worn & connected, safety harnesses distribute the force of a fall across the body, reducing the risk of serious injury. Safety harnesses are necessary for workers in construction, roofing & other high-risk occupations.
- THE SAFETY YOU NEED, THE STYLE YOU WANT - Safety harnesses offer a secure fit for users of all shapes & sizes, ensuring both safety & peace of mind. Harnesses play a vital role in mitigating the risks associated w/ working or engaging in activities at elevated heights. The proper use of safety harnesses significantly reduces the risk of accidents or injuries, and regular inspections ensure harnesses remain in optimal condition, providing reliable protection for workers operating at heights.
- 🧰 WORK SAFELY - Palmer Safety Harnesses are designed and tested to comply with applicable OSHA and ANSI standards for fall protection equipment. When used as a component in a personal fall arrest system, or a personal restraint system, the Palmer Safety harnesses provide workers with the full body harness system
- 🧰 ADJUST WITH EASE - The fall protection body harness has 5 easily accessible adjustment points to ensure a comfortable fit a wide range of body types properly and safely. The dorsal D-ring for fall arrest, hip D-rings, heavy duty back support, tongue buckle leg straps. Palmer Safety Full Body Safety Harness are designed for use by person with a combined Weight (clothing, tools, etc.) of 130 – 300 lbs.
- 🧰 RELIABLY DURABLE - We provide fall protection gear that is built to last and can keep you out of harm’s way. The body harness is build with these physical parameters: Webbing: Polyester, Width: 1.73 in, Breaking Strength: 5000 lbs., Stitching Thread: High-tenacity polyester | Metal Component: Alloy Steel, Finish: Silver or Golden Yellow Galvanized | Weight: 4.28 lbs.
- 🧰 COMPLIANT WITH SAFETY STANDARDS - We take working environment safety very seriously. That’s why our fall protection fall arrest harness complies with OSHA standards as well as meet in some cases exceed ANSI/ASSE Z359.11-2014. A10.32-2012 fall protection requirements. It’s a must-have for safe and fully-compliant work operations in Ports, Highways, Government buildings, Military Installations, Residential & Commercial Construction, Roofing.
- 🧰 WHY PALMER SAFETY: Palmer Safety is a full service fall protection and safety training organization with offices in New Orleans, Houston, New York, and Los Angeles. We believe knowledge is power and, in the case of fall protection, can mean life or death. We offer the complete package: high quality products serviced by experienced personnel with industry knowledge. Put safety on top of your agendas. Add the Palmer Safety 5pt Safety Harness to your cart today!
- 🧰 PEACE OF MIND ON THE JOB - The Palmer Safety Harness Kit is a top-performing and heavy-duty full-body harness that exceeds industry standards set by ANSI/ASSE Z359.11-2014. This complete fall protection package includes a safety lanyard and is also compatible with other types of lanyards, such as those with shock absorbers, roof lifelines, and anchorage tethers. Feel secure while on the job knowing that the Palmer Safety fall protection harness has got you covered.
- 🧰 EQUIPMENT CHOICE for HEIGHT - This single dorsal d-ring located on the back of the harness can be used for fall arrest, travel restraint, and even rescue operations. For more demanding work environments, additional fall prevention accessories may be required. We offer kits and combinations that include roofers anchor points and scaffold cross arm straps to ensure that all your safety needs are met.
- 🧰 ADJUST WITH EASE - Palmer Safety full body harness is designed to accommodate both men and women, and it is essential for both safety and performance that the harness fits properly. It can be adjusted to fit users who weigh between 130 and 310 pounds (59 to 140 kg) and are between 4'10" and 6'6" tall (147 to 198 cm). To ensure a secure fit, make sure all buckles are fastened, the leg and shoulder straps are tight, and the chest strap is positioned in the center of the chest.
- 🧰 COMPLIANT WITH SAFETY STANDARD - We exceeded expectations with our Palmer Safety Full Body Harnesses by meeting and surpassing the requirements set forth in the ANSI/ASSE Z359.11-2014 standard. This standard lays out guidelines for testing fall protection products, including the number of items to be tested, equipment used, and the roles of both the manufacturer and testing lab. You can find more information by checking the Compliance Label/Safety Label on our products.
- 🧰 ANSI & OSHA COMPLIANCE – OSHA ensures the safety and well-being of workers through setting standards and offering training, outreach, education, and assistance. When employees are working at a height of 6 feet or more above lower levels, a personal fall arrest system is mandatory. The Palmer Safety fall protection safety harness is perfect for various job roles such as roofing, residential & commercial construction, arborist, high-rise painting, window and gutter cleaning.
Last update on 2024-04-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.