“This site contains affiliate links for which OEMDTC may be compensated” |
October 28, 2019 NHTSA CAMPAIGN NUMBER: 19V775000
Delay In Seatbelt-Unfastened Telltale/FMVSS 208
Without the seatbelt warning reminder, the driver may forget to fasten the seatbelt, increasing the risk of injury in the event of a crash.
NHTSA Campaign Number: 19V775
Manufacturer Thor Motor Coach
Components SEAT BELTS, ELECTRICAL SYSTEM
Potential Number of Units Affected 378
Summary
Thor Motor Coach (TMC) is recalling certain 2019-2020 Chateau 22B, 22E, 23U, 24F, 25V, and 28A, Daybreak 22GO, Four Winds 22B, 22E, 24F, 26B and 28A, Freedom Elite 22HE and 2020 Quantum GR22, and SE22 motorhomes. The seatbelt-unfastened warning light will not illuminate for approximately five seconds after the ignition is moved to the “on” or “start” position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, “Occupant Crash Protection.”
Remedy
GM will notify TMC owners, and dealers will reprogram the instrument panel cluster, free of charge. The recall began October 3, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, GMC customer service at 1-800-462-8782 or TMC customer service at 1-877-855-2867. TMC’s number for this recall is RC000177.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
IMPORTANT SAFETY RECALL
September 2019
This notice applies to your vehicle, VIN:
Dear Thor Motor Coach Inc:
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
General Motors has decided that certain 2019 model year Chevrolet Express and GMC Savana vehicles may fail to conform to S7.3 of Federal Motor Vehicle Safety Standard (FMVSS) 208, Occupant crash protection. As a result, GM is conducting a recall. We apologize for this inconvenience. However, we are concerned about your safety and continued satisfaction with our products.
I M P O R T A N T
|
Why is your vehicle being recalled? | In these vehicles, the seatbelt-unfastened telltale will not illuminate for approximately five seconds after the ignition is moved to the on or start position. There is no impact to the vehicle’s seatbelt systems, and the telltale will function normally after the five-second delay. A software change implemented for 2019 model year Chevrolet Express and GMC Savana vehicles contains an error that inhibits the activation of the telltale for five seconds after vehicle startup. During the five-second delay, the telltale will not alert the driver that the driver’s seatbelt is unbuckled, increasing the risk of the driver forgetting to buckle the seatbelt and the risk of injury’ in a crash. |
What will we do? | Your Chevrolet dealer will reprogram the instrument panel cluster (IPO). This service will be performed for you at no charge. Because of service scheduling requirements, it is likely that your dealer will need your vehicle longer than the actual inspection and service correction time of approximately 35 minutes. |
What should you do | You should contact your Chevrolet dealer to arrange a service appointment as soon as possible. |
Do you have questions? | If you have questions or concerns that your dealer is unable to resolve, please contact the Chevrolet Customer Assistance Center at 1.800.630.2438 (TTY 1.800.833.2438). |
If after contacting your dealer and the Customer Assistance Center, you are still not satisfied we have done our best to remedy this condition without charge and within a reasonable time, you may wish to write the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590, or call the toll-free Vehicle safety Hotline at 1 .888.327.4236 (TTY 1.800.424.9153), or go to https://www.safercar.gov. The National Highway Traffic Safety Administration Campaign ID Number for this recall is 19V644.
Federal regulation requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.
Maryann L. Combs
Vice President
Global Vehicle Safety
GM Recall: N192264500
SEOCONTENT-START
FMVSS Noncompliance Recall
N192264500 Seatbelt Reminder Telltale Delay
Copyright 2019 General Motors. All Rights Reserved. Page 1 of 4
Release Date:
September 2019
Revision:
01
Revision Description:
This bulletin has been updated to add the customer notification letter. Please discard all copies of N192264500.
Attention:
It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by this notification under a sale or lease until the defect or noncompliance is remedied.
All involved vehicles that are in dealer inventory must be held and not delivered to customers, dealer traded, or used for demonstration purposes until the repair contained in this bulletin has been performed on the vehicle.
Make
Model
Model Year
RPO
Description
From
To
Chevrolet
Express
2019
2019
GMC
Savana
Involved vehicles are marked “open” on the Investigate Vehicle History screen in GM Global Warranty Management system. This site should always be checked to confirm vehicle involvement prior to beginning any required inspections and/or repairs.
Condition
General Motors has decided that certain 2019 model year Chevrolet Express and GMC Savana vehicles may fail to conform to S7.3 of Federal Motor Vehicle Safety Standard (FMVSS) 208, Occupant crash protection. In these vehicles, the seatbelt-unfastened telltale will not illuminate for approximately five seconds after the ignition is moved to the on or start position. There is no impact to the vehicle’s seatbelt systems, and the telltale will function normally after the five-second delay. A software change implemented for 2019 model year Chevrolet Express and GMC Savana vehicles contains an error that inhibits the activation of the telltale for five seconds after vehicle startup. During the five-second delay, the telltale will not alert the driver that the driver’s seatbelt is unbuckled. If the driver does not buckle the seatbelt, this could increase the driver’s risk of injury in the event of a crash.
Correction
Dealers will reprogram the instrument panel cluster (IPC).
Parts
No parts are required for this repair.
Warranty Information
Labor Operation
Description
Labor Time
Trans. Type
Net Item
9104608*
Verified Module Software or Calibration Level: Module Is Programmed with Same Level Software or Calibration
0.2
ZFAT
N/A
9104607*
Instrument Cluster Programming With SPS
0.3
ZFAT
N/A
* To avoid warranty transaction rejections, carefully read and follow the instructions below:
• The SPS Warranty Claim Code must be accurately entered in the “SPS Warranty Claim Code” field of the transaction.
• When more than one Warranty Claim Code is generated for a programming event, it is required to document all Warranty Claim Codes in the “Correction” field on the job card. Dealers must also enter one of the codes in the “SPS Warranty Claim Code” field of the transaction, otherwise the transaction will reject. It is best practice to enter the FINAL code provided by SPS.
Warranty Claim Code Information Retrieval
If the SPS Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS system as follows: 1. Open TIS on the computer used to program the vehicle. 2. Select and start SPS. 3. Select Settings. 4. Select the Warranty Claim Code tab.
FMVSS Noncompliance Recall
N192264500 Seatbelt Reminder Telltale Delay
Page 2 of 4
The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code field.
Service Procedure
Note: Carefully read and follow the instructions below.
• Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector. If there is an interruption during programming, programming failure or control module damage may occur.
• Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. Install a GM Authorized Programming Support Tool to maintain system voltage. Refer to www.gmdesolutions.com for further information. If not available, connect a fully charged 12 V jumper or booster pack disconnected from the AC voltage supply. DO NOT connect a battery charger.
• Turn OFF or disable systems that may put a load on the vehicles battery such as; interior lights, exterior lights (including daytime running lights), HVAC, radio, etc.
• Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M) system status indicators to NO.
5164840
Note: If the Same Calibration/Software Warning is noted on the SPS Summary screen, record the warranty claim code (WCC) and select OK and follow screen instructions. After a successful programming event, the WCC is located in the Service Programming System dialogue box of the SPS Summary screen. No further action is required. Refer to the Warranty section of the bulletin.
1. Reprogram the instrument cluster. Refer to P16 Instrument Cluster: Programming and Setup in SI.
5164843
FMVSS Noncompliance Recall
N192264500 Seatbelt Reminder Telltale Delay
Page 3 of 4
2. Record SPS Warranty Claim Code on job card for warranty transaction submission.
Dealer Responsibility – For USA & Export (USA States, Territories, and Possessions)
It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by this notification under a sale or lease until the defect or noncompliance is remedied.
The US National Traffic and Motor Vehicle Safety Act provides that each vehicle that is subject to a recall of this type must be adequately repaired within a reasonable time after the customer has tendered it for repair. A failure to repair within sixty days after tender of a vehicle is prima facie evidence of failure to repair within a reasonable time. If the condition is not adequately repaired within a reasonable time, the customer may be entitled to an identical or reasonably equivalent vehicle at no charge or to a refund of the purchase price less a reasonable allowance for depreciation. To avoid having to provide these burdensome remedies, every effort must be made to promptly schedule an appointment with each customer and to repair their vehicle as soon as possible. In the recall notification letters, customers are told how to contact the US National Highway Traffic Safety Administration if the recall is not completed within a reasonable time.
Dealer Responsibility – All
All new, used, GM Certified Used, courtesy transportation vehicles, dealer shuttle vehicles, etc. in dealers’ possession and subject to this recall must be held and inspected/repaired per the service procedure of this bulletin before customers take possession of these vehicles. Involved vehicles must be held and not delivered to customers, dealer-traded, released to auction, used for demonstration, or any other purpose.
All GM Certified Used vehicles currently in the dealers’ inventory within the Certified Pre-Owned Inventory System (CPOIS) will be de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting an accepted/paid warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified for sale within the CPOIS system, or once again be used in the CTP program.
Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time forward.
Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions contained in this bulletin. A copy of the customer letter is provided in this bulletin for your use in contacting customers. Recall follow-up cards should not be used for this purpose, since the customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this recall enters your vehicle inventory or is in your dealership for service in the future, you must take the steps necessary to be sure the recall correction has been made before selling or releasing the vehicle.
Dealer Reports
For dealers with involved vehicles, a listing with involved vehicles has been prepared and will be provided to U.S. and Canadian dealers through the GM GlobalConnect Recall Reports or sent directly to export dealers. The listing may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor vehicle registration data for any purpose other than follow-up necessary to complete this recall is a violation of law in several states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to complete this recall.
Courtesy Transportation – For USA
Courtesy transportation is available for customers whose vehicles are involved in a product program and still within the warranty coverage period. See General Motors Service Policies and Procedures Manual, Sections 1.4 and 6.1.10, for courtesy transportation program details.
Customer Notification
USA – General Motors will notify customers of this recall on their vehicle (see copy of customer letter included with this bulletin).
Export – Letters will be sent to known owners of record located within areas covered by the US National Traffic and Motor Vehicle Safety Act. For owners outside these areas, dealers should notify customers using the attached sample letter.
GM bulletins are intended for use by professional technicians, NOT a “do-it-yourselfer”. They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the tools, equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your vehicle may benefit from the information.
We Support Voluntary Technician Certification
FMVSS Noncompliance Recall
N192264500 Seatbelt Reminder Telltale Delay
Page 4 of 4
IMPORTANT SAFETY RECALL
October 2019
This notice applies to your vehicle, VIN: _____________________________________
Dear General Motors Customer:
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
General Motors has decided that certain 2019 model year Chevrolet Express and GMC Savana vehicles may fail to conform to S7.3 of Federal Motor Vehicle Safety Standard (FMVSS) 208, Occupant crash protection. As a result, GM is conducting a recall. We apologize for this inconvenience. However, we are concerned about your safety and continued satisfaction with our products.
IMPORTANT
• Your vehicle is involved in GM safety recall N192264500.
• Schedule an appointment with your GM dealer.
• This service will be performed for you at no charge.
Why is your vehicle being recalled?
In these vehicles, the seatbelt-unfastened telltale will not illuminate for approximately five seconds after the ignition is moved to the on or start position. There is no impact to the vehicle’s seatbelt systems, and the telltale will function normally after the five-second delay. A software change implemented for 2019 model year Chevrolet Express and GMC Savana vehicles contains an error that inhibits the activation of the telltale for five seconds after vehicle startup. During the five-second delay, the telltale will not alert the driver that the driver’s seatbelt is unbuckled, increasing the risk of the driver forgetting to buckle the seatbelt and the risk of injury in a crash.
What will we do?
Your GM dealer will reprogram the instrument panel cluster (IPC). This service will be performed for you at no charge. Because of service scheduling requirements, it is likely that your dealer will need your vehicle longer than the actual inspection and service correction time of approximately 35 minutes.
What should you do?
You should contact your GM dealer to arrange a service appointment as soon as possible.
Do you have questions?
If you have questions or concerns that your dealer is unable to resolve, please contact the appropriate Customer Assistance Center at the number listed below.
Division
Number
Text Telephones (TTY)
Chevrolet
1-800-630-2438
1-800-833-2438
GMC
1-866-996-9463
1-800-462-8583
Puerto Rico – English
1-800-496-9992
Puerto Rico – Español
1-800-496-9993
Virgin Islands
1-800-496-9994
If after contacting your dealer and the Customer Assistance Center, you are still not satisfied we have done our best to remedy this condition without charge and within a reasonable time, you may wish to write the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE, Washington, DC 20590, or call the toll-free Vehicle Safety Hotline at 1.888.327.4236 (TTY 1.800.424.9153), or go to https://www.safercar.gov. The National Highway Traffic Safety Administration Campaign ID Number for this recall is 19V644.
Federal regulation requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.
Maryann L. Combs
Vice President
Global Vehicle Safety
GM Recall: N192264500
9 Affected Products
Vehicles
MAKE | MODEL | YEAR |
THOR | CHATEAU | 2019-2020 |
THOR | DAYBREAK | 2019-2020 |
THOR | FOUR WINDS | 2019-2020 |
THOR | FREEDOM ELITE | 2019-2020 |
THOR | QUANTUM | 2020 |
5 Associated Documents
Owner Notification Letter(Part 577)
RCONL-19V775-4725.pdf 91.757KB
Manufacturer Notices(to Dealers,etc)
RCMN-19V775-9503.pdf 277.634KB
Recall Acknowledgement
RCAK-19V775-1340.pdf 244.832KB
Non-Compliance Notice 573 Report
RCLRPT-19V775-1003.PDF 215.81KB
Manufacturer Notices(to Dealers,etc)-N192264500-01 Bulletin
RCMN-19V775-4161.pdf 277.634KB
Latest Recalls Documents
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V775&docType=RCL
GM Reprogramming
GM Diagnostic/Programming (TIS2Web)
Approved J2534 Device with TIS2WEB can reprogram 1996 and later All GM Modules.
To obtain the latest electronic controller calibration information for your vehicle, go to https://tis2web.service.gm.com/tis2web and enter the vehicle's 17 character Vehicle Identification Number (VIN) and select 'Get CAL ID’.
You can then compare the latest part number with the actual number installed on the vehicle to determine if a reprogram is needed.
The Service Programming System (SPS) application is part of the TIS2Web system. To program an ECU, the SPS application must communicate with the vehicle control modules using the proper J2534 programming interface tool.
The following are the supported interface tools:
The Tech 2 supports model years 1996 and beyond. With the addition of the CAN Diagnostic Interface (CANdi) module, Tech 2 is fully backward compatible with current Tech 2 functionality and operates transparently when diagnosing non-CAN-equipped vehicles.
Servicing the next generation Global A vehicles will require the diagnostic software, GDS2, Global Diagnostic System 2 running on a local PC device while the MDI is connected to the vehicle. The GM MDI is the Global Diagnostic tool for future vehicles starting with Global A vehicles.
The GM MDI was introduced in the fall of 2007 for Pass-Thru programming and offers faster programming speed. It can be used to perform Pass-Thru programming on all vehicles built since 1996 and into the future. Click here to view a list of GDS supported vehicles.
- 【As a multi-protocol Pass-Thru vehicle interface】MaxiFlash Elite is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device. Specially designed to provide users with convenient PC communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, MaxiFlash Elite offers the most significant features desired by OEM customers: reliability, fast performance and flexibility.
- 【MaxiFlash Elite is an accessory tool for MK908P, MS908S Pro】Autel MaxiSys Elite to program ECUs on specific for BMW and for Benz vehicles, in case you lost the J-2534 programmer. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your tablet MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. The functions are NOT universally compatible. Please send VIN number to 🚘jmxd2022@outlook.com📧🚘 to check compatibility before your order. If need any supports, Please contact us.
- 【Wireless with advanced networking functions】Built-In Wireless with advanced networking functions and data storage. Fast performance ensures reprogramming even the newest controllers & Internet upgradable and updatable. Autel MaxiFlash Elite is compatiable with MaxiSYS MS908S, MaxiSYS MS908S Pro , MaxiSYS MS908CV, MaxiCOM MK908, MaxiCOM MK908 Pro, MaxiSYS Elite, MaxiSYS Elite II and Personal Computer
- 【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
- 【Supports simultaneous communication Definition in J2534-1】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed.Rugged aluminum case with non-slip rubber end caps, capable of withstanding harsh environment.
- ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
- J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
- TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
- J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
- FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
- Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, Subaru, & VW/Audi.
- Supports Current GM Vehicles: Now includes CAN-FD, DoIP (Diagnostics over Internet Protocol - as defined in J2534-2) and support for J2534 version 5.0. This is the tool that GM dealerships use for diagnostics and reprogramming.
- NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
- Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
- Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
- Stay up-to-date with thelatest firmware and support of the SM2Pro J2534VCI ECUs programmer, ensuring reliable perform and optimalresults.
- The SM2Pro J2534VCI ECUs programmer is a trustedtool for professional technicians, offering comprehensive functionality and easy integration into your workflows.
- The SM2Pro J2534VCI ECUs programmer offersadvanced functionality for efficient and precise ECUs programming.
- With its 67IN1 without dongle & OBDcompatibility, the SM2Pro J2534VCI ECUs programmer provides a versatilesolution for read and write operations.
- Experienceseamless ECUs programming with the SM2Pro J2534VCI, designed to streamlines the read and write processes for enhanced efficiency.
- 【ALL-IN-1 REPROGRAMMING TOOL】With its exceptional compatibility, TOPDON RLink Lite J2534 pass-thru programmer and enhanced VCI seamlessly conducts original equipment-level diagnostics, programming, and coding jobs, achieving OE-level diagnostics across various vehicle models with a single device. Note: TOPDON RLink Lite is Window-only, not compatible with Mac.
- 【J2534 REPROGRAMMING TOOL】The RLink Lite functions as a J2534 pass-thru programmer to achieve OEM programming and diagnostics. Compliant with three major automotive industry standards D-PDU/J2534/RP1210, and latest DoIP/CAN/CAN FD, the RLink Lite ensures extensive vehicle coverage and speedy diagnostics.
- 【ENHANCED VCI】The TOPDON RLink Lite operates as a versatile VCI box, enabling you to achieve advanced diagnostic, programming, and coding functionalities when paired with OE software. Moreover, TOPDON's DMS Driver Management System helps you easily master the OE software by offering drivers for various brands.
- 【FASTER & SMOOTHER】Powered by a 1.8 GHz quad-core processor, enjoy swift response and seamless operation. The RLink Lite Enhanced VCI runs on Android 11.0 for advanced features and top-notch security. With 2GB RAM and 32GB ROM, storage is ample for smooth performance and quick access to data and apps.
- 【PACKAGE+J2534 SUPPORT】The package comprises the RLink Lite main unit, a 2m OBDII diagnostic cable, a 5m Ethernet cable, a 1.5m USB 2.0 data cable, a 12V DC power adapter, and a quick start guide. Enjoy complimentary technical support from our dedicated TOPDON team for any J2534-related inquiries or concerns throughout the lifespan of your device.
- 【Autel MaxiFlash VCI】👉The MaxiFlash VCI is a bluetooth-enabled vehicle communication interface (VCI) and a J2534-1 and J2534-2 compliant pass-thru programming device. Compatible with the MaxiSYS MS909 advanced diagnostics tablet. The MaxiFlash VCI supports CAN FD, 4 CAN Channels, D-PDU, ISO22900-1 & ISO 22900-2 protocols and is RP1210 compliant.
- 【Programming Compatibility】👉The MaxiFlash VCI is a D-PDU, SAE J2534 & RP1210 compliant PassThru programming interface. Using the updated OEM software, it is capable of replacing the existing software/firmware in the Electronic Control Units (ECU), programming new ECUs, and fixing software-controlled drivability issues and emission issues.
- 【Communication Compatibility】👉The MaxiFlash VCI supports Bluetooth (BT), Wi-Fi, and USB communications. It can transmit vehicle data to the tablet with or without a cable connection. In open areas, the working range of the transmitter through Bluetooth communication is up to 328 feet (about 100 m). The working range of 5G Wi-Fi is up to 164 feet (50 m). If the signal is lost due to being taken out of range, communication will be restored once the tablet is within range.
- 👉The MaxiFlash VCI can be used with a Windows computer with applicable OE subscription for vehicle module programming and when connected to the MaxiSYS MS909 tablet for BMW and for Mercedes (compatible) vehicle module programming.
- 👉Includes One-Year Limited Warranty. This VCI Kit also includes an Autel Main Cable V2.0, USB 2.0 cable, and AC/DC adapter. 🚦If you have any other question, feel free to contact 📧 mbdh2022@outlook. com 📧
Last update on 2024-06-18 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.