Ad Blocker Detected
Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker.
NHTSA ID Number: 10161690
Manufacturer Communication Number: CK19-16
Summary
ISRI SEAT BELT WITH SENSOR INSTALLATION (ACCESSORY KIT 23687694)
3 Affected Products
Vehicle
| MAKE | MODEL | YEAR |
|---|---|---|
| PREVOST | H3-45 | 2017-2019 |
DESCRIPTION
On the vehicles affected by this bulletin, a new seat belt buckle with warning sensor (telltale/buzzer) must be installed on the driver’s seat following the instruction below. Accessory Kit # 23687694 must be run to activate the system at the end of the procedure.
Conversion Kit CK19-16
Writer: MG
Date Expiration Revision Page
06.2019 N/A 0 1(17)
First Release
06-03-2019
ISRI SEAT BELT WITH SENSOR INSTALLATION (ACCESSORY KIT 23687694)
Prevost / Volvo Vehicles
DESCRIPTION
On the vehicles affected by this bulletin, a new seat belt buckle with warning sensor (telltale/buzzer) must be installed on the driver’s seat following the instruction below. Accessory Kit # 23687694 must be run to activate the system at the end of the procedure.
MODEL YEAR(S) AND VEHICLES INVOLVED
Model
VIN
H3-45 coaches
Model Year : 2017 - 2019
2PCH33490HC713599, 2PCH33493HC713600, 2PCH33497HC713602, 2PCH33490HC713604, 2PCH33494HC713606, 2PCH33498HC713608, 2PCH3349XHC713626, 2PCH33493HC713628, 2PCH33495HC713629, 2PCH33497HC713826, 2PCH33497HC713843, 2PCH33490HC713859, 2PCH33496HC713865, 2PCH33494JC713899, 2PCH33496JC713905, 2PCH33497JC713928, 2PCH33499JC713932, 2PCH33494JC713952, 2PCH33492JC713965, 2PCH33495JC713992, 2PCH33491JC710006,
2PCH33490JC710031, 2PCH33494JC710078, 2PCH33491KC710282, 2PCH33490KC710290, 2PCH33495KC710320, 2PCH33490KC710323, 2PCH33495KC710348, 2PCH33498KC710375, 2PCH33498KC710389, 2PCH33490KC710399, 2PCH33492KC710419, 2PCH33491KC710430, 2PCH33492KC710467, 2PCH33497KC710478
MATERIAL NEEDED
Order the following parts:
Part No.
Description
Qty
860332
SEAT BELT ASS W/SENSOR
1
562548
TERMINAL, MOLEX .093 SOCKET 20-14AWG
2
562549
CONNECTOR, MOLEX .093 2 SH
1
Equipment that may be required:
Part No.
Description
Qty
Laptop with PTT (Premium TechTool, latest version installed) & related cables.
1
NOTE
Material can be obtained through regular channels.
Conversion Kit CK19-16
Revision Page
0 2(17)
Writer: MG <QF7720961 rev8>
PROCEDURE
DANGER
Park vehicle safely, apply parking brake, stop engine. Prior to working on the vehicle, set the ignition switch to the OFF position and trip the main circuit breakers equipped with a trip button. On Commuter type vehicles, set the battery master switch (master cut-out) to the OFF position.
Lock out & Tag out (LOTO) must be performed during set-up, maintenance or repair activities. Refer to your local procedure for detailed information regarding the control of hazardous energy.
1. Remove seat base (cushion) from the seat.
- Lift-up center lever and slide seat base (cushion) to the foremost position.
- Remove handle from seat base (remove two mounting screws).
- Hold center lever in upper position and push it sideward (left) to disengage it.
- Make sure the seat base is at its full forward position and lift it up to free it from the seat.
Conversion Kit CK19-16
Revision Page
0 3(17)
Writer: MG <QF7720961 rev8>
2. Remove seat belt from the seat.
- Unscrew the belt lower mount Torx screw (lift the backrest adjustment lever to uncover the screw).
- Remove both seat armrests.
- Disengage J hooks and cut the cable ties holding together the lower edges of the backrest seat cover.
Conversion Kit CK19-16
Revision Page
0 4(17)
Writer: MG <QF7720961 rev8>
- Remove the backrest seat cover (unhook the side and center Velcro’s).
- Pass the belt and belt buckle through the seat cover opening.
- Unscrew the belt upper mount (special Torx screw with shoulder).
- Remove the cardboard covering at the back of the seat backrest and pass the belt and buckle through the seat opening.
Conversion Kit CK19-16
Revision Page
0 5(17)
Writer: MG <QF7720961 rev8>
- Remove the belt mechanism plastic cover at the back of the seat (remove the 4 trim clips by pushing out the center pin).
- Disengage the sliding rail clip at the back of the seat to free the belt from the rail (press one of the pin and slide clip up or down).
- Unscrew the seat belt mechanism from the back of the seat (Torx screw).
Conversion Kit CK19-16
Revision Page
0 6(17)
Writer: MG <QF7720961 rev8>
3. Remove seat buckle from the seat base.
- Unscrew the buckle dust cover (a small # 6 Torx screwdriver is required).
- Detach the side plastic cover to access the buckle hold down Torx screw.
- Remove the buckle and dust cover.
Conversion Kit CK19-16
Revision Page
0 7(17)
Writer: MG <QF7720961 rev8>
4. Install new seat buckle.
- Pass the buckle end and harness through the dust cover (it is not be possible to install the dust cover with the buckle already secured to the seat).
- Pass the new buckle harness through the air supply line opening at the back of the seat.
- Secure the new buckle to the seat using one of the new supplied Torx screw (make sure the locating pin is engaged). Apply medium strength (blue) thread locker to the screw threads TORQUE: 35 Nm (26 lb-ft).
- Reattach the side plastic cover and re-install the dust cover.
Conversion Kit CK19-16
Revision Page
0 8(17)
Writer: MG <QF7720961 rev8>
5. Install new seat belt and mechanism.
- Secure the new belt mechanism to the base of the seat (Apply medium strength (blue) thread locker to the screw threads but hand tight only, use new supplied Torx screw).
NOTE
The new seat belt mechanism does not have a locating tab.
- Position the belt in the sliding rail and reinstall the rail clip.
- Pass the belt end and belt buckle through seat and seat cover opening.
- Secure the top part of the belt at the opening in the backrest. Use the supplied special Torx screw with shoulder. Apply medium strength (blue) thread locker to the screw threads. TORQUE: 35 Nm (26 lb-ft).
- Secure the lower part of the belt to the seat (behind the adjustment lever). Center the belt end in the cover opening and tighten. Apply medium strength (blue) thread locker to the screw threads TORQUE: 35 Nm (26 lb-ft).
Conversion Kit CK19-16
Revision Page
0 9(17)
Writer: MG <QF7720961 rev8>
- Make sure that the belt is centered in the top part of the sliding rail and that there is no belt to rail contact at the lower part of the rail. Adjust the angle of the seat belt mechanism as required.
Conversion Kit CK19-16
Revision Page
0 10(17)
Writer: MG <QF7720961 rev8>
- When correctly positioned, tighten the belt mechanism Torx hold down screw to its final torque 35 Nm (26 lb-ft).
- Re-install the cardboard at the back of the seat (use masking tape to hold in place).
- Slide back the seat cover over the backrest, hook the side and center Velcro’s.
- Secure the seat cover at the bottom of the backrest using cable ties. Re-attach J-hooks on both sides.
- Re-install both armrests. Apply medium strength (blue) thread locker to the screw threads TORQUE: 22 Nm (16 lb-ft).
- Make sure the belt is operating properly (moving & retracting freely). Adjust the mechanism angle as required to ensure proper operation and reinstall the belt mechanism cover.
Conversion Kit CK19-16
Revision Page
0 11(17)
Writer: MG <QF7720961 rev8>
6. Connect the buckle harness to the vehicle (vehicles with connector under the seat).
NOTE
Some vehicle may already be equipped with a belt buckle connector located under the seat base.
If present, the connector will be coming from the vehicle front compartment (air supply hole in the floor under the seat).The connector is sometime secured to the seat base frame as shown.
A jumper wire is connected to the end of it to simulate a fastened belt and prevent the illumination of the dashboard belt telltale light.
- Locate the belt buckle connector under the seat (typical location shown, actual location may vary).
- Disconnect the jumper wire at the end of the connector.
- Cut the end of the new belt buckle harness previously installed and shorten harness to the required length.
- Splice the ends of both buckle harness wire and crimp the two supplied 562548 terminals.
- Insert the terminals in the supplied 562549 connector.
- Connect the belt buckle harness to the connector under the seat.
Conversion Kit CK19-16
Revision Page
0 12(17)
Writer: MG <QF7720961 rev8>
Conversion Kit CK19-16
Revision Page
0 13(17)
Writer: MG <QF7720961 rev8>
7. Connect the buckle harness to the vehicle (vehicles without connector under the seat).
- Route the buckle harness down to the air supply hose opening in the vehicle floor (secure to seat frame with cable ties).
NOTE
Make sure that the harness will not get pinched by internal seat components (during seat adjustment or seat movement).
- Pass the harness inside the vehicle front compartment (through air supply opening).
- Inside the front compartment, connect the harness to the C.SE51 connector.
- Secure the harness with cable ties inside the compartment.
Conversion Kit CK19-16
Revision Page
0 14(17)
Writer: MG <QF7720961 rev8>
PROGRAMMING STEPS:
1. In Premium TechTool, select PROGRAM tab. In PROGRAM tab, select operation 1700-22-03-06 Accessory Kit then clicks START.
2. Enter Accessory kit number 23687694 Click on PROGRAM button below and then follow the instructions. The programming process will start
Conversion Kit CK19-16
Revision Page
0 15(17)
Writer: MG <QF7720961 rev8>
Conversion Kit CK19-16
Revision Page
0 16(17)
Writer: MG <QF7720961 rev8>
Conversion Kit CK19-16
Revision Page
0 17(17)
Writer: MG <QF7720961 rev8>
PARTS / WASTE DISPOSAL
Discard waste according to applicable environmental regulations (Municipal/State[Prov.]/ Federal)
ESTIMATED TIME
The time required to perform this special bulletin is approximately 3.0 hours.
Access all our Service Bulletins on http://techpub.prevostcar.com/en/
or scan the QR-Code with your smart phone.
E-mail us at [email protected]volvo.com and type “ADD” in the subject to receive our warranty bulletins by e-mail.
Prevost engages in a continuous program of testing and evaluating to provide the best possible product. Prevost, however, is not committed to, or liable for updating existing products.
CK19-16
06.2019
https://www.nhtsa.gov/recalls?nhtsaId=10161690
https://static.nhtsa.gov/odi/tsbs/2019/MC-10161690-0001.pdf
- Simple & Non-Toxic - Condition & protect in one simple step to maintain any finished leather surface
- Use On - Use regularly on accessories such as leather, purses, shoes, boots, briefcases & handbags.
- Protect - UVX - Sunscreen protects all types of leather from sun damage, fading, drying & cracking.
- Restore - Safely removes dirt, soil & residue to soften, strengthen & moisturize neglected leather.
- Recommended - Finished leather surfaces including car interior shoes boots briefcases handbags & coats
- It’s Not Just for Car Seats & Interiors: This kit works on all things leather, seats, interiors, jackets, shoes, sneakers, boots, sofas and more; Everyone has something leather in their home.
- Treat Your Leather Like Your Hair & Skin: We all wash our skin and hair on a regular basis, and use conditioners and lotions to keep out skin hydrated and fresh.
- PH Balanced: Leather Cleaner is pH balanced for the most efficient cleaning and preserves the leather's strength, durability and appearance; Penetrates the pores of leather to lift and suspend dirt and oils
- Fast, Easy & Fun: No one "loves to clean", but if you are using products that make it fast and easy, it's certainly more fun both products are extremely easy to use, and leave no residue like soaps, nor will they contribute to fiber deterioration
- Keep Your Leather Looking & Smelling New: Leather cleaner is colorless and odorless and penetrates the pores of your leather to lift and remove dirt and oils, while leather conditioner, which has a subtle leather scent, contains Vitamin E to nourish your leather and help reduce UV damage
- MADE IN THE USA by a small family business that specializes in the best leather cleaner and conditioner on the market. (I removed the millions line)
- TRUSTED: Our family has been developing leather care products since 1968, and our premium, time-tested leather cleaner has millions of satisfied customers.
- QUICKLY AND GENTLY CLEANS all types of leather and vinyl, removing dirt, oil, tough stains and grime. Non-toxic leather cleaner is perfect for every leather product, including saddles and tack, automotive interiors, furniture, handbags, shoes and jackets. Not for use on suede.
- UNLIMITED 100% SATISFACTION GUARANTEE. If you're not happy with any of our products, simply return them for a full refund of your purchase price!
- SPECIALLY FORMULATED to work with Leather Honey Leather Conditioner, the #1 best-selling leather care product on Amazon.
- Easily clean and condition leather to renew its appearance and prolong suppleness with this 2-step Lexol Leather Regimen Kit
- Kit contains: (1) 8 oz. bottle of All Leather Deep Cleaner, (1) 8 oz. bottle of All Leather Deep Conditioner, and 2 Premium Applicator Sponges
- Cleaner restores and revives leather by lifting dirt and oils, allowing them to be easily wiped away
- Conditioner contains fine oil droplets that nourish, restore flexibility, and protect leather against cracking without leaving greasy residue
- Easy-to-use cap dispenses, Ideal for use on: leather auto upholstery, footwear, furniture, handbags & briefcases, sports equipment and luggage
- Weiman Leather Wipes - Non Toxic Clean Condition UV Protection Help Prevent Cracking or Fading of Leather Couches, Car Seats, Shoes, Purses
- Simple & Non Toxic - Condition & protect in one simple step to maintain any finished leather surface
- Use on - Use regularly on accessories such as leather, purses, shoes, boots, briefcases & handbags.
- Protect - UVX - Sunscreen protects all types of leather from sun damage, fading, drying & cracking.
- Restore - Safely removes dirt, soil & residue to soften, strengthen & moisturize neglected leather.
- OUR LEATHER CONDITIONER WAS INVENTED OVER 50 YEARS AGO WITH MILLIONS OF HAPPY CUSTOMERS. Same time-tested formula used today!
- ONE TREATMENT LASTS SIX MONTHS OR LONGER. Deeply penetrates into the leather's pores to protect new leather and rejuvenate old leather. Softens, moisturizes and promotes flexibility leaving your leather feeling and looking beautiful! A little goes a long way; no need to reapply monthly as with other products.
- THIS LEATHER CONDITIONER PROLONGS THE LIFE OF ALL TYPES OF LEATHER, including leather furniture and upholstery, automobile and motorcycle seats, boots, gloves, purses, jackets, saddles and tack. Non-toxic, non-solvent, not sticky, no odor and does not contain silicone. Water, snow and rain repellent formula. Not for use on suede or faux leather/vinyl.
- UNLIMITED 100% SATISFACTION GUARANTEE. If you're not satisfied, return the product at any time for a full refund.
- A LEATHER CONDITIONER THAT IS MADE IN THE USA by a small family business owned by the grandchildren of the original inventor. Use with Leather Honey Leather Cleaner, also available on Amazon!
- ☑️ Safe for many surfaces - Will also work on durablend, vinyl, compound, saffiano, faux and other leather or leather-like surfaces.
- ☑️ Easy to use - simply spray on and wipe off to eliminate almost any surface stain and give new life to your leather.
- ☑️ Effective and Safe - Works to remove dirt, debris, stains, and grime without using harsh chemicals.
- ☑️ Premium Formula - Developed by leather experts to deliver top quality results.
- ☑️ Extend the Life of Your Leather - Routine cleaning and conditioning can help quality leather goods to last a lifetime
- Bring Leather Back To Life, Prolongs the Life of Leather. Softens Stiff Leather, Safe to Use on Glove Soft Leather, Furniture, Jackets, Car Seats, Purses, Shoes, and More
- Dermatologist Tested- Does Not Irritate Skin. No Greasy Residue, Reduces Scuffs and Scratches
- Simple & Non Toxic - Leather cleaner is ideal for maintaining any smooth, finished leather surface. Clean, condition and protect all in one step
- Use On - Use leather cleaner regularly on your favorite accessories such as leather purses, shoes, boots, briefcases and handbags
- Protect - UVX - Sunscreen protects leather from fading, drying and cracking
- Restore - Safely removes dirt, soil, and residue from your leather product, soften, strengthen, and moisturize neglected leather
- Recommended - Finished leather surfaces including car interior shoes boots briefcases handbags & coats - Do not use on suede, nubuck, Natuzzi Brand or any unfinished leather
- Simple & Non-Toxic - Condition & protect in one simple step to maintain any finished leather surface
- Use On - Use regularly on accessories such as leather, purses, shoes, boots, briefcases & handbags
- Protect - UVX - Sunscreen protects all types of leather from sun damage, fading, drying & cracking
- Restore - Safely removes dirt, soil & residue to soften, strengthen & moisturize neglected leather
- Recommended - Finished leather surfaces including car interior shoes boots briefcases handbags & coats
Last update on 2020-03-28 / Affiliate links / Images from Amazon Product Advertising API
Last update on 2020-03-28 / Affiliate links / Images from Amazon Product Advertising API
