FL807 – Tie-Rod Separation Due to Vibration – 2013-2016 Freightliner Cascadia

“This site contains affiliate links for which OEMDTC may be compensated”

February 12, 2019 NHTSA CAMPAIGN NUMBER: 19V093000

Tie-Rod Separation Due to Vibration

A tie-rod failure would cause a disconnect between the front wheels, resulting in a loss of steering ability, thereby increasing the risk of a crash.

 

NHTSA Campaign Number: 19V093

Manufacturer Daimler Trucks North America LLC

Components STEERING

Potential Number of Units Affected 111

 

Summary

Daimler Trucks North America LLC (DTNA) is recalling certain 2013-2016 Freightliner Cascadia vehicles equipped with Hendrickson 5″ drop axles. In certain front axle, brake lining, and brake spider combinations, braking may cause high vibrations, resulting in early failure of the tie-rod tube.

 

Remedy

DTNA will notify owners, and dealers will replace the stamped brake spiders and the tie-rod, free of charge. The recall began April 12, 2019. Owners may contact DTNA customer service at 1-800-547-0712. DTNA’s number for this recall is FL-807.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check for Daimler Trucks North America Recalls

 


Recall Campaign

April 2019
FL807A-E
NHTSA #19V-093
Transport Canada #2019-066
Page 1 Table 1, Cont. on page 2
REVISED NOTICE

 

Subject: Hendrickson 5 Inch Drop Axle Tie Rods

Models Affected: Specific Freightliner Cascadia vehicles manufactured April 30, 2012, through May 26, 2015, equipped with Hendrickson 5 inch drop axle tie rods, brake linings, and stamped spiders.

 

General Information

Daimler Trucks North America LLC (DTNA), on behalf of its Freightliner Trucks Division, has decided that a defect that relates to motor vehicle safety exists on the vehicles mentioned above.

There are approximately 112 vehicles involved in this campaign.

In certain circumstances, high brake vibrations may occur due to a specific combination of Hendrickson 5 inch drop axle tie rods, brake linings, and stamped spiders. These vibrations may lead to a reduced fatigue life and early separation of the tie rod. Separation of the tie rod may lead to a disconnect between the front wheels of the vehicle and reduce the ability to steer the vehicle, which could increase the risk of a crash.

Tie rods and stamped brake spiders will be replaced.

REVISION: The tie rod replacement part numbers have been corrected and the parts table revised.

 

Additional Repairs

Dealers must complete all outstanding Recall and Field Service campaigns prior to the sale or delivery of a vehicle. A Dealer will be liable for any progressive damage that results from its failure to complete campaigns before sale or delivery of a vehicle.

Owners may be liable for any progressive damage that results from failure to complete campaigns within a reasonable time after receiving notification.

 

Work Instructions

Please refer to the attached work instructions. Prior to performing the campaign, check the vehicle for a completion sticker (Form WAR260).

 

Replacement Parts

REVISION: The Tie Rod replacement part numbers have been corrected and the parts table revised.

Replacement parts are now available and can be obtained by ordering the part number(s) listed below from your facing Parts Distribution Center.

If our records show your dealership has ordered any vehicles involved in campaign number FL807, a list of the customers and vehicle identification numbers will be available in OWL. Please refer to this list when ordering parts for this recall.

Table 1 – Replacement Parts for FL807

Campaign Number Part Description Part Number Qty.
FL807A BRAKE ASSEMBLY KIT,SPECIAL-WITH TWO Q PL TDA KIT8335 1 ea
BRAKE-DRUM,1H O65TL 878 937 136 .50 CM 10041543 2 ea
TIE ROD ASSEMBLY HDR 76878 002 1 ea
FL807B BRAKE ASSEMBLY KIT,SPECIAL-WITH TWO Q PL TDA KIT8335 1 ea
BRAKE DRUM/X30 TDA 53 123815 002 2 ea
TIE ROD ASSEMBLY HDR 76878 002 1 ea

 

Table 1, Cont. on page 2

Campaign Number Part Description Part Number Qty.
FL807C BRAKE ASSEMBLY KIT,SPECIAL-WITH TWO Q PL TDA KIT8335 1 ea
DUST SHIELD TDA A3264S227 4 ea
DRUM 1H O65TT 878 937 110 .50 CM 10014756 2 ea
WASHER-SPLIT,3/8IN 23-09318-011 12 ea
SCREW-CAP,HEX3/8-16X.5 23-10746-050 12 ea
TIE ROD ASSEMBLY HDR 76878 002 1 ea
FL807D BRAKE ASSEMBLY KIT,SPECIAL-WITH TWO Q PL TDA KIT8335 1 ea
BRAKE-DRUM,1H O65TL 878 937 136 .50 CM 10041543 2 ea
DUST SHIELD TDA A3264S227 4 ea
WASHER-SPLIT,3/8IN 23-09318-011 12 ea
SCREW-CAP,HEX3/8-16X.5 23-10746-050 12 ea
TIE ROD ASSEMBLY HDR 76878 001 1 ea
FL807E BRAKE ASSEMBLY KIT,SPECIAL-WITH TWO Q PL TDA KIT8335 1 ea
BRAKE-DRUM,1H O65TL 878 937 136 .50 CM 10041543 2 ea
TIE ROD ASSEMBLY HDR 76878 001 1 ea
FL807A-E BLANK COMPLETION STICKER WAR260 1 ea

 

Table 1, Cont. from page 1

 

Removed Parts

U.S. and Canadian Dealers, please follow Warranty Failed Parts Tracking shipping instructions for the disposition of all removed parts. Export distributors, please destroy removed parts unless otherwise advised.

 

Labor Allowance

Table 2 – Labor Allowance

Campaign Number Procedure Time Allowed (hours) SRT Code Corrective Action
FL807A-E REPLACE TIE ROD AND BRAKE SPIDERS 8.8 996-R065A 12-Repair Recall/Campaign

 

Table 2

IMPORTANT: When the Recall has been completed, locate the base completion label in the appropriate location on the vehicle, and attach the red completion sticker provided in the recall kit (Form WAR260). If the vehicle does not have a base completion label, clean a spot on the appropriate location of the vehicle and first attach the base completion label (Form WAR259). If a recall kit is not required or there is no completion sticker in the kit, write the recall number on a blank sticker and attach it to the base completion label.

 

Claims for Credit

You will be reimbursed for your parts, labor, and handling (landed cost for Export Distributors) by submitting your claim through the Warranty system within 30 days of completing this campaign. Please reference the following information in OWL:

  • Claim type is Recall Campaign.
  • In the Campaign field, enter the campaign number and appropriate condition code (e.g. FL807-A, FL807-B, etc.).
  • In the Primary Failed Part Number field, enter 25-FL807-000.
  • In the Parts field, enter the appropriate part number(s) as shown in the Replacement Parts Table.
  • In the Labor field, first enter the appropriate SRT from the Labor Allowance Table. Administrative time will be included automatically as SRT 939-6010A for 0.3 hours.
  • The VMRS Component Code is 015-004-045 and the Cause Code is A1 – Campaign.
  • S. and Canada — Reimbursement for Prior Repairs. When a customer asks about reimbursement, please do the following:
  • Accept the documentation of the previous repair.
  • Make a brief check of the customer’s paperwork to see if the repair may be eligible for reimbursement. (See the “Copy of Owner Letter” section of this bulletin for reimbursement guidelines.)
  • Submit an OWL Recall Pre-Approval Request for a decision.
  • Include the approved amount on your claim in the Other Charges section.
  • Attach the documentation to the pre-approval request.
  • If approved, submit a based on claim for the pre-approval.
  • Reimburse the customer the appropriate amount.

IMPORTANT: OWL must be viewed prior to performing the recall to ensure the vehicle is involved and the campaign has not been previously completed. Also, check for a completion sticker prior to beginning work.

U.S. and Canadian dealers, contact the Warranty Campaigns Department via Web inquiry at DTNAConnect.com / WSC, or the Customer Assistance Center at (800) 385-4357, after normal business hours, if you have any questions or need additional information. Export distributors, submit a Web inquiry or contact your International Service Manager.

U.S. and Canadian Dealers: To return excess kit inventory related to this campaign, U.S. dealers must submit a Parts Authorization Return (PAR) to the Memphis PDC. Canadian dealers must submit a PAR to their facing PDC. All kits must be in resalable condition. PAR requests must include the original purchase invoice number. Export Distributors: Excess inventory is not returnable.

The letter notifying U.S. and Canadian vehicle owners is included for your reference.

Please note that the National Traffic and Motor Vehicle Safety Act, as amended (Title 49, United States Code, Chapter 301), requires the owner’s vehicle(s) be corrected within a reasonable time after parts are available to you. The Act states that failure to repair a vehicle within 60 days after tender for repair shall be prima facie evidence of an unreasonable time. However, circumstances of a particular situation may reduce the 60 day period. Failure to repair a vehicle within a reasonable time can result in either the obligation to (a) replace the vehicle with an identical or reasonably equivalent vehicle, without charge, or (b) refund the purchase price in full, less a reasonable allowance for depreciation. The Act further prohibits dealers from selling a vehicle unless all outstanding recalls are performed. Any lessor is required to send a copy of the recall notification to the lessee within 10 days. Any subsequent stage manufacturer is required to forward this notice to its distributors and retail outlets within five working days.

 

Copy of Notice to Owners

Subject: Hendrickson 5 Inch Drop Axle Tie Rods

For the Notice to U.S. Customers: This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. For the Notice to Canadian Customers: This notice is sent to you in accordance with the Canadian Motor Vehicle Safety Act.

Daimler Trucks North America LLC (DTNA), on behalf of its Freightliner Trucks Division, has decided that a defect that relates to motor vehicle safety exists on specific Freightliner Cascadia vehicles manufactured April 30, 2012, through May 26, 2015, equipped with Hendrickson 5 inch drop axle tie rods, brake linings, and stamped spiders.

In certain circumstances, high brake vibrations may occur due to a specific combination of Hendrickson 5 inch drop axle tie rods, brake linings, and stamped spiders. These vibrations may lead to a reduced fatigue life and early separation of the tie rod. Separation of the tie rod may lead to a disconnect between the front wheels of the vehicle and reduce the ability to steer the vehicle, which could increase the risk of a crash.

Tie rods and stamped brake spiders will be replaced.

Please contact an authorized Daimler Trucks North America dealer to arrange to have the Recall performed and to ensure that parts are available at the dealership. To locate an authorized dealer, search online at www.Daimler-TrucksNorthAmerica.com. On the menu tab, select “Contact,” scroll down to “Find a Dealer,” and select the appropriate brand. The Recall will take approximately nine hours and will be performed at no charge to you.

You may be liable for any progressive damage that results from your failure to complete the Recall within a reasonable time after receiving notification.

If you do not own the vehicle that corresponds to the identification number(s) which appears on the Recall Notification, please return the notification to the Warranty Campaigns Department with any information you can furnish that will assist us in locating the present owner. If you have leased this vehicle, Federal law requires that you forward this notice to the lessee within 10 days. If you are a subsequent stage manufacturer, Federal law requires that you forward this notice to your distributors and retail outlets within five working days. If you have paid to have this recall condition corrected prior to this notice, you may be eligible to receive reimbursement. Please see the reverse side of this notice for details.

For the Notice to U.S. Customers: If you have questions about this Recall, please contact the Warranty Campaigns Department at (800) 547-0712, 7:00 a.m. to 4:00 p.m. Pacific Time, Monday through Friday, e-mail address DTNA.Warranty.Campaigns@Daimler.com, or the Customer Assistance Center at (800) 385-4357 after normal business hours. If you are not able to have the defect remedied without charge and within a reasonable time, you may wish to submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590; or call the Vehicle Safety Hotline at (888) 327-4236 (TTY: 800-424-9153); or to https://www.safercar.gov. For the Notice to Canadian Customers: If you have questions about this Recall, please contact the Warranty Campaigns Department at (800) 547-0712, 7:00 a.m. to 4:00 p.m. Pacific Time, Monday through Friday, e-mail address DTNA.Warranty.Campaigns@Daimler.com, or the Customer Assistance Center at (800) 385-4357 after normal business hours.

We regret any inconvenience this action may cause but feel certain you understand our interest in motor vehicle safety.

WARRANTY CAMPAIGNS DEPARTMENT

Enclosure


Reimbursement to Customers for Repairs Performed Prior to Recall

If you have already paid to have this recall condition corrected you may be eligible to receive reimbursement.

Requests for reimbursement may include parts and labor. Reimbursement may be limited to the amount the repair would have cost if completed by an authorized Daimler Trucks North America LLC dealer. The following documentation must be presented to your dealer for consideration for reimbursement.

Please provide original or clear copies of all receipts, invoices, and repair orders that show:

  • The name and address of the person who paid for the repair
  • The Vehicle Identification Number (VIN) of the vehicle that was repaired
  • What problem occurred, what repair was done, when the repair was done
  • Who repaired the vehicle
  • The total cost of the repair expense that is being claimed
  • Proof of payment for the repair (such as the front and back of a cancelled check or a credit card receipt) Reimbursement will be made by check from your Daimler Trucks North America LLC dealer.

Please speak with your Daimler Trucks North America LLC authorized dealer concerning this matter.


Work Instructions

Subject: Hendrickson 5 Inch Drop Axle Tie Rods

Models Affected: Specific Freightliner Cascadia vehicles manufactured April 30, 2012, through May 26, 2015, equipped with Hendrickson 5 inch drop axle tie rods, brake linings, and stamped spiders.

Spider Plate and Tie Rod Replacement

REVISION: The Tie Rod replacement part numbers have been corrected and the parts table revised.

  1. Check the base label (Form WAR259) for a completion sticker for FL807 (Form WAR260) indicating this work has been completed. The base label is usually located on the passenger-side door, about 12 inches (30 cm) below the door latch. If a completion sticker is present, no work is needed. If a completion sticker is not present, proceed to the next step.
  1. Park the vehicle on a level surface, shut down the engine, and set the parking brake. Chock the tires on the rear axle.
  2. Raise the front axle and place safety stands under the frame or axle. Be sure the stands will support the weight of the vehicle.
  3. Remove the front wheels. Refer to the Cascadia Workshop Manual, Section 40.00, Subject 100.
  4. Remove the front hubs. Refer to Section 33.01, Subject 100 in the Cascadia Workshop Manual.
  5. Remove the brake assembly. Refer to the applicable section in Group 42 of the Cascadia Workshop Manual.
  6. Disconnect the tie rod from the tie rod arms; see 1. Remove the tie rod from the vehicle and discard it.
  1. Attach a new tie rod to the tie rod arms. Tighten the castle nut 120 to 170 lbf·ft (163 to 230 N·m) plus a maximum of one-sixth of a turn to align a slot in the castle nut with the cotter pin hole in the tie rod stud. Insert the cotter pin and bend the tangs to secure it.
  2. Clean and inspect all brake parts that will be reused. Refer to the applicable section in Group 42 of the Cascadia Workshop Manual.

NOTE: The spider plates, brake shoes, and dust shield (if equipped) will be replaced.

  1. Install the brake components using the new spider plates, brake shoes, and dust shield (if equipped). Referto the applicable section in Group 42 of the Cascadia Workshop Manual.
  2. Install the front hubs. Refer to Section 33.01, Subject 100 in the Cascadia Workshop Manual.
  3. Install the front wheels. Refer to the Cascadia Workshop Manual, Section 40.00, Subject 100.
  4. Remove the safety stands and lower the vehicle.
  5. Align the front axle of the vehicle. See the vehicle Workshop Manual, Group 33.
  6. Clean a spot on the base label (Form WAR259), write the recall number, FL807, on a red completion sticker(Form WAR260), and attach it to the base label to show this work has been completed.

 


Daimler Trucks
North America LLC

 

April 2019
FL807A-D
NHTSA #19V-093

 

IMPORTANT SAFETY RECALL

This notice applies to your vehicle(s)

Subject: Hendrickson 5 Inch Drop Axle Tie Rods

 

This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.

Daimler Trucks North America LLC (DTNA), on behalf of its Freightliner Trucks Division, has decided that a defect that relates to motor vehicle safety exists on specific Freightliner Cascadia vehicles manufactured April 30, 2012, through May 26, 2015, equipped with Hendrickson 5 inch drop axle tie rods, brake linings, and stamped spiders.

In certain circumstances, high brake vibrations may occur due to a specific combination of Hendrickson 5 inch drop axle tie rods, brake linings, and stamped spiders. These vibrations may lead to a reduced fatigue life and early separation of the tie rod. Separation of the tie rod may lead to a disconnect between the front wheels of the vehicle and reduce the ability to steer the vehicle, which could increase the risk of a crash.

Tie rods and stamped brake spiders will be replaced.

Please contact an authorized Daimler Trucks North America dealer to arrange to have the Recall performed and to ensure that parts are available at the dealership. To locate an authorized dealer, search online at www.Daimler-TrucksNorthAmerica.com. On the menu tab, select “Contact,” scroll down to “Find a Dealer,” and select the appropriate brand. The Recall will take approximately nine hours and will be performed at no charge to you.

You may be liable for any progressive damage that results from your failure to complete the Recall within a reasonable time after receiving notification.

If you do not own the vehicle that corresponds to the identification number(s) which appears on the Recall Notification, please return the notification to the Warranty Campaigns Department with any information you can furnish that will assist us in locating the present owner. If you have leased this vehicle, Federal law requires that you forward this notice to the lessee within 10 days. If you are a subsequent stage manufacturer, Federal law requires that you forward this notice to your distributors and retail outlets within five working days. If you have paid to have this recall condition corrected prior to this notice, you may be eligible to receive reimbursement. Please see the reverse side of this notice for details.

 

If you have questions about this Recall, please contact the Warranty Campaigns Department at (800) 547-0712, 7:00 a.m. to 4:00 p.m. Pacific Time, Monday through Friday, e-mail address DTNA.Warranty.Campaigns@ Daimler.com, or the Customer Assistance Center at (800) 385-4357 after normal business hours. If you are not able to have the defect remedied without charge and within a reasonable time, you may wish to submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1220 New Jersey Avenue, SE, Washington, DC 20590; or call the Vehicle Safety Hotline at (888) 327-4236 TTY: (800) 424-9153); or to https://www.safercar.gov.

 

We regret any inconvenience this action may cause but feel certain you understand our interest in motor vehicle safety.

 

WARRANTY CAMPAIGNS DEPARTMENT

Enclosure


Reimbursement to Customers for Repairs Performed Prior to Recall

If you have already paid to have this recall condition corrected you may be eligible to receive reimbursement.

Requests for reimbursement may include parts and labor. Reimbursement may be limited to the amount the repair would have cost if completed by an authorized Daimler Trucks North America LLC dealer. The following documentation must be presented to your dealer for consideration for reimbursement.

Please provide original or clear copies of all receipts, invoices, and repair orders that show:

  • The name and address of the person who paid for the repair.
  • The Vehicle Identification Number (VIN) of the vehicle that was repaired.
  • What problem occurred, what repair was done, when the repair was done.
  • Who repaired the vehicle.
  • The total cost of the repair expense that is being claimed.
  • Proof of payment for the repair (such as the front and back of a cancelled check or a credit card receipt).

Reimbursement will be made by check from your Daimler Trucks North America LLC dealer.

Please speak with your Daimler Trucks North America LLC authorized dealer concerning this matter.


4 Affected Products

Vehicle

MAKE MODEL YEAR
FREIGHTLINER CASCADIA 2013-2016

 


11 Associated Documents

Defect Notice 573 Report

RCLRPT-19V093-3991.PDF 212.987KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.00 KB]

 


Miscellaneous Document- 573 Defect Information Report

RMISC-19V093-0310.pdf 493.028KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [481.47 KB]

 


Recall Acknowledgement

RCAK-19V093-4897.pdf 245.814KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [240.05 KB]

 


Manufacturer Notices(to Dealers,etc)

RCMN-19V093-7034.pdf 37.317KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [36.44 KB]

 


Remedy Instructions and TSB

RCRIT-19V093-9500.pdf 247.803KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [242.00 KB]

 


Remedy Instructions and TSB

RCRIT-19V093-1670.pdf 247.925KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [242.11 KB]

 


ISSUED Owner Notification Letter(Part 577)

RCONL-19V093-9842.pdf 453.735KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [443.10 KB]

 


Remedy Instructions and TSB

RCRIT-19V093-5260.pdf 132.169KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [129.07 KB]

 


Remedy Instructions and TSB

RCRIT-19V093-1439.pdf 125.606KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [122.66 KB]

 


Recall Quarterly Report #1, 2019-2

RCLQRT-19V093-8506.PDF 211.137KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.19 KB]

 


Recall Quarterly Report #2, 2019-3

RCLQRT-19V093-5582.PDF 211.234KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.28 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V093&docType=RCL

 


 

Bestseller No. 1
Lucas Oil 10046 SAE 80W-90 Heavy Duty Gear Oil - 1 Gallon
  • Contains extraordinary anti-wear and lubricity agents, ensuring exceptional protection against wear and reducing drag
  • Helps to control heat
  • Incorporates Lucas cutting-edge additive technology derived from top-rated Lucas Heavy Duty Oil Stabilizer, the number one supplemental oil in the heavy-duty industry
  • Available in 1 quart and 1 gallon bottle sizes
SaleBestseller No. 2
Lucas Oil 10043 SAE 80W-90 Heavy Duty Gear Oil - 1 Quart
  • Contains extraordinary anti-wear and lubricity agents, ensuring exceptional protection against wear and reducing drag
  • Helps to control heat
  • Incorporates Lucas cutting-edge additive technology derived from top-rated Lucas Heavy Duty Oil Stabilizer, the number one supplemental oil in the heavy-duty industry
  • Available in 1 quart and 1 gallon bottle sizes
Bestseller No. 3
Valvoline High Performance SAE 80W-90 Gear Oil 1 QT
  • Protects Against Severe Temperatures To Help Extend Service Life
  • Formulated With Extreme-Pressure Additives To Minimize Gear Wear From Shock Loads
  • Helps Protect Against Gear Wear From Scuffing, Scouring, Corrosion And Pitting
  • Recommended For Conventional Hypoid Differentials And Non-Synchronized Manual Transmissions In Passenger Cars, Light Trucks, Sport Utility Vehicles, Vans And Heavy-Duty Trucks Where An Api-Gl5 Or Gl-4 Fluid Is Specified
Bestseller No. 4
Genuine Ford Fluid XY-80W90-QL SAE 80W-90 Premium Rear Axle Lubricant - 1 Quart
  • Meets warranty requirements and is recommended for conventional and limited-slip differentials of passenger cars, light trucks, vans and buses
  • Formulated for automotive use
  • Use according to owner guide recommendations
  • Recommended by Ford Motor Company
  • Motorcraft SAE 80W-90 Premium Rear Axle Lubricant is an excellent multi-purpose extreme pressure lubricant
SaleBestseller No. 5
Pennzoil 550042102 Axle 80-W90 (GL-5) - 1 Quart
  • Maintains fluidity at low temperatures.
  • Does not thin out at high temperatures
  • prevents rust
  • Resists oxidation
  • Withstands shock loads
Bestseller No. 6
Triax Gear Premium LS 80W-90, GL-5 Limited Slip Ready, Manual Transmissions, Hypoid Gear Systems, Differentials, NATO Military Approved, Widest OEM Specification Range (1 Gallon)
  • WIDEST SPEC RANGE ON THE MARKET - Widely compatible with a very large number of hypoid gear systems, differentials, transmissions and axle assemblies from VOLVO, Mack, MAN, ZF, EATON, and many others.
  • SEVERE SERVICE MAX - Exceptional shear stability and oxidation resistance. Polyphosphate EP proprietary additive system offers a substantial improvement in performance over the previous generation, low cost, gear oils.
  • BUILT-IN LIMITED SLIP ADPAK - Does not require "additional" LS additive. It is built into the product and optimized for all limited slip differentials including those with built-in wet brakes.
  • OUTSTANDING SCUFFING PROTECTION - Superb gear and syncron protection, facilitating extremely long transmission life. Exceeds Load Stage 13 extreme pressure requirements beyond 120,000 lbs / sqi.
  • SHEAR STABLE - Excellent thermal stability and high load capacity without viscosity breakdown which facilitates excellent film strength under high loads, high temp and high shear conditions.
Bestseller No. 7
Ultra1Plus SAE 80W-90 Conventional Gear Oil API GL-5 (US Gallon - 4 QTS)
  • ✅ Extended gear and bearing life due minimal deposits.
  • ✅ Exceptional thermal stability and resistance to high temperature oxidation.
  • ✅ Longer seal life.
  • ✅ Reduced maintenance cost and longer equipment life.
  • ✅ Effective low temperature lubrication.
Bestseller No. 8
GL-5 80W90 Heavy Duty Automotive Gear Oil - 5 Gallon Pail
  • Sinopec GL-5 Heavy Duty Automotive Gear Oil is a range of high-performance gear oils, available in six viscosity grades, formulated with high-quality mineral base oils, and an advanced multifunctional additive system to meet the requirements of API GL-5. Designed for the lubrication of hypoid gear sets in passenger vehicles and commercial vehicles, where they offer excellent extreme pressure (EP) and anti-wear properties.
  • Certifications: API GL-5, MIL L-2015D, MAN 343 Type M1, ZF TE_ML 05A, TE-ML 19B, TE-ML 21A
  • Pack Size: 5 Gallon Pail (18L Volume)
Bestseller No. 9
Yukon Gear & Axle (OK 3-QRT-Conv-A) 80W90 Conventional Gear Oil with Positraction Additive - 3 Quart
  • 3 Quart 80W90 conventional gear oil
  • Brand of gear oil may vary, but product is all of superior quality
  • Includes a bottle of Yukon positraction additive
SaleBestseller No. 10
80W-90 Premium Gear Lube - Marine Engine - 32 Ounce" />
Quicksilver 80W-90 Premium Gear Lube - Marine Engine - 32 Ounce
  • Provides maximum protection against excessive wear, corrosion and pitting for extended gear life in marine applications
  • Contains additives to protect gears if water enters the gear case or lower unit
  • Recommended for use in outboard motor gear cases and marine lower units in applications below 75hp
  • 80W-90 viscosity
  • 32 oz. bottle (pack of 6)

Last update on 2024-03-12 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...