“This site contains affiliate links for which OEMDTC may be compensated” |
July 10, 2023 NHTSA CAMPAIGN NUMBER: 23V472000
Front Brake Caliper May Detach
Damaged brake calipers can detach and cause a loss of braking ability, increasing the risk of a crash.
NHTSA Campaign Number: 23V472
Manufacturer Yamaha Motor Corporation, USA
Components SERVICE BRAKES, HYDRAULIC
Potential Number of Units Affected 211
Summary
Yamaha Motor Corporation, USA (Yamaha) is recalling certain 2022 Tenere 700 (XTZ7N) motorcycles. The front brake calipers may have been assembled with bolts that have an incorrect thread length, which can damage the mounting hole threads in the brake caliper.
Remedy
Owners should not operate their motorcycle, other than take it to a dealer, until the remedy is performed. Dealers will inspect the length of the front brake caliper bolts and replace them, if necessary. If the caliper mounting-hole threads are damaged, the caliper will be replaced. Repairs will be performed free of charge. Owner notification letters are expected to be mailed July 20, 2023. Owners may contact Yamaha’s customer service at 1-800-962-7926. Yamaha’s number for this recall is 990168.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
SAFETY RECALL | This modification has top priority. This bulletin must be performed immediately to ensure customer safety.
NOTE: Bulletins that announce a recall will have an “R” at the end of the bulletin number. |
CERTAIN 2022-MODEL XTZ7N (TÉNÉRÉ 700) MOTORCYCLES
FACTORY MODIFICATION CAMPAIGN – Incorrect Brake Caliper Bolts
INTRODUCTION
Yamaha Motor Corporation, U.S.A. has decided that a defect that relates to motor vehicle safety exists in certain 2022 model XTZ7N (Ténéré 700) motorcycles.
In affected motorcycles, the front brake calipers may have been assembled with one or more bolts that have an incorrect thread length. Incorrect bolts can cause damage to the mounting hole threads in brake caliper if repeatedly removed and reinstalled, such as during servicing. Then, in the worst case, the bolts would no longer hold the front brake caliper to its mount, so the caliper would detach, resulting in loss of braking ability, increasing the risk of loss of control and a crash with injury or death.
To correct this defect, Yamaha is initiating a Factory Modification Campaign. Affected units must have the length of the front brake caliper mounting bolts confirmed. If found to be incorrect, the bolt(s) must be replaced with correct specification bolt(s) and the mounting-hole threads in the calipers inspected.
If the caliper mounting-hole threads(s) are damaged, the caliper must be replaced as well.
Yamaha is notifying all registered owners of affected motorcycles by mail. A copy of this letter is included in this bulletin. The customer should take this letter along with the affected vehicle to an authorized Yamaha dealer for modification.
If your dealership was invoiced for one or more affected vehicles, a computer report listing all affected motorcycles invoiced to your dealership is included with a mailed copy of this bulletin. Use the list to help ensure all motorcycles are modified. All sold motorcycles that have been registered with Yamaha will show the customer’s name and address.
Your dealership must notify the owner of any affected Ténéré 700 that was actually sold but listed as “unsold” in the report. You must modify all affected motorcycles in your inventory as well as all customer-owned motorcycles brought to you for this service. Any affected motorcycle that you purchase from Yamaha in the future may also require modification. If you purchase an affected vehicle from another dealer or Yamaha, check to see if the procedures in this bulletin have already been performed before you sell the vehicle.
Unsold motorcycles that are affected should not be sold and sold vehicles should not be operated except to take the vehicle to the dealer for inspection and, if required, modification. It is a violation of Yamaha policy for your dealership to deliver any affected vehicle to customers until the procedures in this bulletin are performed.
When the inspection and, if necessary, modification on each motorcycle is performed, follow the Warranty Information section of this bulletin to receive reimbursement. Be sure to use the Factory Modification Campaign procedures in Chapter 7 of the Warranty and Y.E.S. Handbook (P/N: LIT-11760-00-21).
DEALER ACTION SUMMARY
Unsold & Sold Units:
|
Use YDS Unit Status to check to be sure the unit is affected and that it is not already modified. |
Parts Required: | Yes, if inspection determines that one or more bolts are incorrect. See the Parts Information section of this bulletin for more information. |
Warranty: | Factory Modification Campaign. See the Warranty Information section of this bulletin. This modification applies to all affected units regardless of ownership or warranty status. |
Notify Customers: | Yes, you must immediately contact any customer whose Ténéré 700 shows as unregistered on the report enclosed with the mailed copy of this bulletin. Yamaha has sent letters to customers whose motorcycles were registered with Yamaha as of xx/xx/2023. |
AFFECTED RANGE
Check Unit Status on YDS to make sure the Primary ID (PID) is in the Affected Range and is eligible for this modification campaign. The affected unit range for this issue is:
Model Year | Model | Primary ID | ||
Prefix | From | To | ||
2022 | XTZ7N | DM12Y | 002428 | 002638 |
IMPORTANT: Affected Primary IDs may not be consecutive. Always check YDS Unit Status before starting any repair.
SERVICE PROCEDURE
- On one side and then the other, remove and measure the thread length of the front brake caliper bolts as indicated. The bolt threads should be 20 mm long on a bolt that is 40 mm long. Any other dimensions are incorrect, and the bolt should be replaced.
- If both bolts are correct, reinstall and tighten them to the specified torque.
Mounting Bolt: 40 Nm (4.0 kgf-m, 30 lb-ft)
- If either bolt or both bolts are incorrect, clean the mounting hole threads in the caliper. Visually inspect the threads for damage and use a clean bolt of the correct type to see if it can be threaded into the hole smoothly.
If the threads are stripped or otherwise damaged, the caliper must be replaced. Use an Online Tech Request to submit a photo of the damage before proceeding. Follow Ténéré 700 Service Manual (P/N: LIT-11616-3555) procedures to replace the caliper and union bolt gaskets. Bleed the brake system using Yamalube DOT 4 Brake Fluid (P/N: ACC-BRAKE-FL-UD).
- Install the bolts, using new bolts to replace any incorrect ones. Tighten the bolts to the specified torque.
Mounting Bolt: 40 Nm (4.0 kgf-m, 30 lb-ft)
IDENTIFICATION PROCEDURE
After completing the procedure, make sure to properly record and submit the warranty claim for this campaign to ensure correct reimbursement and to update the vehicle’s repair history in Yamaha’s database.
PARTS INFORMATION
PART NAME | OLD PART NUMBER | NEW PART NUMBER | QTY | DLR COST |
BOLT, FLG | 90105-10778-00 | ← | 1-4 | $1.79 |
*Order quantity is varies depending on the number of incorrect bolts installed.
Part identification
Part number: 90105-10778
Hexagon head bolt with flange
Nominal designation of thread: M10×1.25
Nominal length: 40 mm
Thread length: 20 mm
Flange diameter: Φ20
NOTE: If a caliper or both calipers need to be replaced, refer to the parts list on PartsManager Pro™ for the correct part numbers (right and left side calipers are different, and you will need up to five new union bolt gaskets).
Chronology :
In June, 2023 Yamaha Motor corporation USA was informed by the manufacturer, Yamaha Motor Co., LTD that such a condition could exist in previously modified units. This was determined pursuant to quality control review, testing and a review of foreign models that use substantially similar part design.
1 Affected Product
Vehicle
MAKE | MODEL | YEAR |
YAMAHA | TENERE 700 | 2022 |
3 Associated Documents
Recall Acknowledgement
RCAK-23V472-2347.pdf 646.283KB
Defect Notice 573 Report
RCLRPT-23V472-7988.PDF 215.911KB
Remedy Instructions and TSB
RCRIT-23V472-5154.pdf 597.934KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=23V472&docType=RCL
- 【Premium Aftermarket Part】Go Kart Brake Caliper,Our product offers top-grade direct replacement for the factory brake caliper, perfect for those in need of a quality aftermarket option.
- 【Fully Equipped】Rear Brake Caliper,Our brake caliper comes fully assembled, with a set of pre-installed brake pads, saving you time and hassle.
- 【Unparalleled Quality】Rear Brake Caliper Assembly,Crafted from top-tier aluminum alloy, our brake caliper guarantees high durability and resistance to high temperatures, ensuring lasting efficiency.
- 【High Reliability】ATV Rear Brake Caliper,Boasting a heavy-duty design and stable characteristics, our brake caliper provides outstanding reliability, giving you peace of mind.
- 【Simple Installation】Motorcycle Rear Brake Caliper,Our easy-to-install brake caliper flawlessly blends with your original motorcycle aesthetics. Ideally designed for 100-125CC engine motorcycles, it is a perfect fit for your needs.
- Upgrade your stock brakes with this stealth, lightweight and compact 4- Piston brake Caliper!
- CNC machined from 6061 billet aluminum to eliminate flex and reduce weight then CHROME Plated
- Utilizes stainless steel pistons and anti-rattle springs for increased performance and excellent wear resistance. Brake pads slide freely on ground pins to prolong pad life. Comes with brake pads, ground pins, pin springs, washers and set screw.
- Can be set-up for a front or rear brake application. Designed for use with DOT-5 brake fluid for optimum performance.
- We have mounting kits available to fit many different Harley models. These calipers also work with Billet Proof brake hanger kits!
- Scope of application: This brake caliper rear fits for 100-125CC engine motorcycle.
- Aluminum Alloy Material: brake caliper motorcycle is made of high quality aluminum alloy material, durable and high-temperature resistant.
- Excellent performance:Fully assembled, including a set of brake pads pre-installed; Heavy duty design, stable characteristics and high reliability. Great aftermarket replacement part, direct replace the factory brake caliper.
- Packaging & Easy Installation: Rear Brake Caliper Assembly Package includes 1 * Rear Brake Caliper. Easy installation, perfect match to your original motorcycle
- Product Detail: Built to meet standard specification, strictly follow factory quality control.Fine workmanship, wear‑resistance and the service life is longer.
- Manufacturer Part # 45150-MEN-006 45510-KRN-305 Replacement Part# 45150-MKE-A71 45150-MEN-A51 45510-KCE-671 45510-MEN-J01 45510-KRN-A91
- Fitment: Compatible with Honda Motorcycle ▶CR125R 2004-2007 ▶CR250R 2004-2007 ▶CRF250R 2004-2020 ▶CRF250RX 2019-2020 ▶CRF250X 2004-2017 ▶CRF450R 2004-2020 ▶CRF450RWE 2019-2020 ▶CRF450X 2005-2017
- Feature: This is high quality OEM specifications front brake assembly. Easy install saving your time and your labour.
- Service:If there is any product problem within 1 year, please contact us to solve it for you.We provide product service.
- Manufacturer Part # 59300-08D00-999 Replacement Part# 59300-27C11-999 59300-27C00
- Fitment: Fit for Suzuki Motorcycle ▶DR250 1990-1995 ▶DR350 1990-1999 ▶RM125 1986-1995 ▶RM250 1986-1995 ▶RMX250T 1989-1996
- Feature: Perfect aftermarket replacement of Suzuki brake caliper 59300-08D00-999. With brake pads, banjos, exact mounting bracket, direct install.
- Package:A Brake Caliper W/Pads is packed in a fine box.
- Service:If there is any product problem within 1 year, please contact us to solve it for you.We provide product service.
- This brake calipers Suitable for most of Motorcycle ATV Quad Kart GY6 Scooter
- Brake caliper is Made of high-quality aluminum alloy material, which is durable and has a long service life. it can be used for a long time
- Easy to install,just connect the brake caliper with the original part and tighten the screws.easily complete the assembly
- Pls confirm the size and compatibility before you purchase the brake caliper.to ensure it is the right item you need
- We are a manufacturer of high-quality ATV and motorcycles with the highest quality materials. we have been committed to providing customers with quality products and services.
- Effortless Functionality: Our brake pad separator streamlines operations, minimizing labor and maximizing convenience. Designed for seamless use, this spreader tool effortlessly pushes the brake caliper piston forward without risking damage to its surface, ensuring optimal performance and ease of use for every application.
- Premium-Quality Construction: Crafted from high-grade metal, this caliper piston spreader tool guarantees durability, wear resistance, and corrosion protection. Engineered for longevity, it promises reliable performance over an extended lifespan, ensuring consistent and dependable usage for all your braking needs.
- Precision Design: Featuring a meticulously crafted thread, our brake pad spreader ensures smooth and efficient operation with every use. The precision-engineered design delivers both ease of use and unparalleled efficiency, making it an indispensable tool for brake maintenance tasks.
- Versatile Compatibility: Equipped with a tommy bar and compatible with 1/2'' drive ratchet wrenches or 0.83'' spanners, this brake caliper press tool offers versatile functionality for various applications. Its chemically blackened steel spreader plates (measuring 2"x2-1/4" each) boast a maximum spread of 3-1/4", catering to a wide range of brake caliper configurations.
- Wide-Ranging Application: Ideal for use with Nissan, Alfa Romeo, Audi, Fiat, Ford, GM (Vauxhall/Opel), Peugeot, Renault, Rover, VW, and Porsche vehicles, our disc brake pad spreader tool offers compatibility across multiple car brands, making it an essential addition to any automotive maintenance toolkit.
- 【Made for Dirt Pit Bikes】This brake kit for bike is compatible with 50cc, 70cc, 90cc, 110cc, and 125cc dirt pit bike brake systems. It's compatible with setups with a 1.69" caliper mounting hole center distance
- 【Superb Braking Force】The disc master cylinder and the bike calipers with double pistons adopt a pressure-holding design. This prevents air from entering and negatively affecting the braking power
- 【Longer Lasting】Equipped with hard-wearing and heatproof brake pads with 15,000km service life. The master cylinder is made with low-pressure casting technology to create a high-strength cavity
- 【No Leaking Or Dripping Oils】Equipped with a high-purity and high-sealing nit-rile rubber, it stands well against damage caused by extreme temperatures, heat, and oil. A 10mm oiling screw cap is included
- 【Complete Bike Disc Brake Kit】The package includes 1 front disc brake assembly with brake pad and 1 extra pair of brake pads
- 🛒【Efficient Tool】- It helps to push the brake piston of the brake caliper backward without damaging the piston surface.
- 🛒【Material】- Chemically blackened steel spreader plates, chrome screws with connecting rods, durable.(2"x2-1/4") Each plates, Max Spread 3-1/4".
- 🛒【Feature】- Equipped with tommy bar and can be used with 1/2'' drive ratchet wrench or 0.83'' spanner. Suitable for most ATE, Bendix, Delco and Girling calipers.
- 🛒【Widely Used】- Compatible for Nissan, Alfa, Audi, Fiat, Ford, GM(Vauxhall/Opel), Peugeot, Renault, Rover, VW, Porsche.
- 🛒【Purchase with Confidence】- If you have any comments on the product you received, we will definitely provide you with the most satisfactory solution.
- Manufacturer Part # 45150-KZ4-J21
- Replacement Part # 45150-KCY-671 45150-K28-911 45150-MAC-681 45100-KV6-672 45150-KZ4-J31 45100-KZ1-601 45150-KV6-305
- Fit for Honda CR125R 1995-2003 CR250R 1995-2003 CR500R 1995-2001
- Fit for Honda CRF125F 2014-2020 CRF150F 2003-2017 Except CRF150R/RB Edition CRF230F 2003-2019 CRF250F 2019-2020 Except CRF250L/R Edition CRF450R 2002-2003
- Fit for Honda XR250L 1991-1996 XR250R 1993-2004 XR400R 1996-2004 XR600R 1993-2000 XR650R 2000-2007 Except XR650L Edition
Last update on 2024-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
©2023 YAMAHA MOTOR CORPORATION, U.S.A. MOTORCYCLE xx/xx/2023 M2023-XXXR SAFETY RECALL This modification has top priority. This bulletin must be performed immediately to ensure customer safety. NOTE: Bulletins that announce a recall will have an “R” at the end of the bulletin number. CERTAIN 2022-MODEL XTZ7N (TÉNÉRÉ 700) MOTORCYCLES FACTORY MODIFICATION CAMPAIGN – Incorrect Brake Caliper Bolts Yamaha Motor Corporation, U.S.A. has decided that a defect that relates to motor vehicle safety exists in certain 2022 model XTZ7N (Ténéré 700) motorcycles. In affected motorcycles, the front brake calipers may have been assembled with one or more bolts that have an incorrect thread length. Incorrect bolts can cause damage to the mounting hole threads in brake caliper if repeatedly removed and reinstalled, such as during servicing. Then, in the worst case, the bolts would no longer hold the front brake caliper to its mount, so the caliper would detach, resulting in loss of braking ability, increasing the risk of loss of control and a crash with injury or death. To correct this defect, Yamaha is initiating a Factory Modification Campaign. Affected units must have the length of the front brake caliper mounting bolts confirmed. If found to be incorrect, the bolt(s) must be replaced with correct specification bolt(s) and the mounting-hole threads in the calipers inspected. If the caliper mounting-hole threads(s) are damaged, the caliper must be replaced as well. Yamaha is notifying all registered owners of affected motorcycles by mail. A copy of this letter is included in this bulletin. The customer should take this letter along with the affected vehicle to an authorized Yamaha dealer for modification. If your dealership was invoiced for one or more affected vehicles, a computer report listing all affected motorcycles invoiced to your dealership is included with a mailed copy of this bulletin. Use the list to help ensure all motorcycles are modified. All sold motorcycles that have been registered with Yamaha will show the customer’s name and address. Your dealership must notify the owner of any affected Ténéré 700 that was actually sold but listed as “unsold” in the report. You must modify all affected motorcycles in your inventory as well as all customer-owned motorcycles brought to you for this service. Any affected motorcycle that you purchase from Yamaha in the future may also require modification. If you purchase an affected vehicle from another dealer or Yamaha, check to see if the procedures in this bulletin have already been performed before you sell the vehicle. Unsold motorcycles that are affected should not be sold and sold vehicles should not be operated except to take the vehicle to the dealer for inspection and, if required, modification. It is a violation of Yamaha policy for your dealership to deliver any affected vehicle to customers until the procedures in this bulletin are performed. Page 1 of 6 IN I i I INTRODUCTION When the inspection and, if necessary, modification on each motorcycle is performed, follow the Warranty Information section of this bulletin to receive reimbursement. Be sure to use the Factory Modification Campaign procedures in Chapter 7 of the Warranty and Y.E.S. Handbook (P/N: LIT-11760-00-21). Unsold & Sold Units: Use YDS Unit Status to check to be sure the unit is affected and that it is not already modified. Parts Required: Yes, if inspection determines that one or more bolts are incorrect. See the Parts Information section of this bulletin for more information. Warranty: Factory Modification Campaign. See the Warranty Information section of this bulletin. This modification applies to all affected units regardless of ownership or warranty status. Notify Customers: Yes, you must immediately contact any customer whose Ténéré 700 shows as unregistered on the report enclosed with the mailed copy of this bulletin. Yamaha has sent letters to customers whose motorcycles were registered with Yamaha as of xx/xx/2023. Check Unit Status on YDS to make sure the Primary ID (PID) is in the Affected Range and is eligible for this modification campaign. The affected unit range for this issue is: Model Year Model Primary ID Prefix From To 2022 XTZ7N DM12Y 002428 002638 IMPORTANT: Affected Primary IDs may not be consecutive. Always check YDS Unit Status before starting any repair. 1. On one side and then the other, remove and measure the thread length of the front brake caliper bolts as indicated. The bolt threads should be 20 mm long on a bolt that is 40 mm long. Any other dimensions are incorrect, and the bolt should be replaced. Page 2 of 6 l.b~ I DEALER ACTION SUMMARY l”‘I AFFECTED RANGE I • I SERVICE PROCEDURE 0.. .. e 2. If both bolts are correct, reinstall and tighten them to the specified torque. Mounting Bolt: 40 Nm (4.0 kgf-m, 30 lb-ft) 3. If either bolt or both bolts are incorrect, clean the mounting hole threads in the caliper. Visually inspect the threads for damage and use a clean bolt of the correct type to see if it can be threaded into the hole smoothly. If the threads are stripped or otherwise damaged, the caliper must be replaced. Use an Online Tech Request to submit a photo of the damage before proceeding. Follow Ténéré 700 Service Manual (P/N: LIT-11616-35- 55) procedures to replace the caliper and union bolt gaskets. Bleed the brake system using Yamalube DOT 4 Brake Fluid (P/N: ACC-BRAKE-FL-UD). 4. Install the bolts, using new bolts to replace any incorrect ones. Tighten the bolts to the specified torque. Mounting Bolt: 40 Nm (4.0 kgf-m, 30 lb-ft) After completing the procedure, make sure to properly record and submit the warranty claim for this campaign to ensure correct reimbursement and to update the vehicle’s repair history in Yamaha’s database. Page 3 of 6 40 N-m (4 .0 kgt-m, 30 lb,ft) 5 ~~ IDENTIFICATION PROCEDURE Page 4 of 6 PART NAME OLD PART NUMBER NEW PART NUMBER QTY DLR COST BOLT, FLG 90105-10778-00 ← 1-4 $1.79 *Order quantity is varies depending on the number of incorrect bolts installed. Part identification Part number: 90105-10778 Hexagon head bolt with flange Nominal designation of thread: M10×1.25 Nominal length: 40 mm Thread length: 20 mm Flange diameter: Φ20 NOTE: If a caliper or both calipers need to be replaced, refer to the parts list on PartsManager Pro™ for the correct part numbers (right and left side calipers are different, and you will need up to five new union bolt gaskets). The owner of each registered vehicle will receive a letter announcing this campaign. The customer’s letter includes the Vehicle Identification Number and Recall Number. The modification is authorized for all affected motorcycles, both sold and unsold, regardless of ownership or warranty status. You do not need the customer’s letter to perform the inspection or modification or to file for reimbursement. Submit a Recall Claim as described below using Campaign Number 990168, choosing the appropriate modification condition from the drop down menu. The labor allowances are as follows: • Inspect Bolts = 0.2 hours • Replace 1-2 Bolts = 0.2 hours plus 2 bolts • Replace 3-4 Bolts = 0.2 hours plus 4 bolts • Replace LEFT Caliper & 1-4 Bolts = 0.6 hours plus 4 bolts, left caliper, 2 union bolt gaskets & 1 bottle brake fluid • Replace RIGHT Caliper & 1-4 Bolts = 0.6 hours plus 4 bolts, right caliper, 3 union bolt gaskets & 1 bottle brake fluid • Replace BOTH Calipers & 1-4 Bolts = 1.2 hours plus 4 bolts, both calipers, 5 union bolt gaskets & 1 bottle brake fluid I ~~ I PARTS INFORMATION 10 l~I WARRANTY INFORMATION 0 ,-t e 40 lD N ,-t X 0 ,-t ~ Page 5 of 6 To submit your Recall Claim on YDS, go to Service > Warranty Claims/Authorization > Claims/Authorization > New. Then, from the menu, select Recall / Service per Bulletin. If you have any questions about proper procedures for Factory Modification Campaigns, see Chapter 7 in your Warranty and Y.E.S. Handbook (P/N: LIT-11760-00-21). Add New Claim / Authorization i:::::I Warranty Claim ——————~ O Warranty / Y.E.S. Claim If request is under $1500 I@ Recall/ Service per Bulletin I Q Parts and ACC Quality Assurance Claim i:::::I Warranty Authorization —————~ O Warranty / Y.E.S. Authorization If request is $1500 or over O Out of Warranty Authorization Q Un-Registered / Un-Sold Unit Authorization i:::::I Shipping Damage —————– §.hiP.P.inQ Damage Policies and Procedures O Visible Damage Authorization – Pictures Required Q Concealed Damage Claim $349 and under Q Concealed Damage Authorization $350 and over Pictures Required O Missing Parts Claim $349 and under Q Missing Parts Authorization $350 and over E+MHl111 Add New Claim / Authorization Unit Recall/Service Campaign This screen allows you to enter Recall Request ITTIOffllation for single or multiple Primary IDs NOTE. ThesamerecalllnlOffllatlonwlllbeusedloralloftheprlmarylDsprovlded. •campaign,: C– PrimarylD:l~–~I (OR) VIN/HIN: c=– iihiihf-ifrii I i?ii ~- ~ ►iii&’· IN Primary ID Finish Date Miles or Hours ~ Fih!M’I !’hi Page 6 of 6 IMPORTANT SAFETY RECALL NOTICE This notice applies to your vehicle, VIN xxxxxxxxxxxxxxxxx Model: xxxxxx XX XX, 2023 990168 Dear Yamaha Owner: Yamaha Motor Corporation, U.S.A. has decided that a defect that relates to motor vehicle safety exists in certain 2022 model XTZ7N (Ténéré 700) motorcycles. Our records indicate that you own the affected vehicle shown above. The reason for this recall: In affected motorcycles, the front brake calipers may have been assembled with one or more bolts that have an incorrect thread length. Incorrect bolts can cause damage to the mounting hole threads in brake caliper if repeatedly removed and reinstalled, such as during servicing. Then, in the worst case, the bolts would no longer hold the front brake caliper to its mount, so the caliper would detach, resulting in loss of braking ability, increasing the risk of loss of control and a crash with injury or death. What is Yamaha and your dealer will do: To correct this defect, Yamaha is initiating a Factory Modification Campaign. Affected units must have the length of the front brake caliper mounting bolts confirmed. If found to be incorrect, the bolt(s) must be replaced with correct specification bolt(s) and the mounting-hole threads in the calipers inspected. If the caliper mounting-hole threads(s) are damaged, the caliper must be replaced as well. Inspection takes a little less than 15 minutes; the procedure can take up to around an hour and fifteen minutes if both calipers should require replacement. Your dealer may need to have your motorcycle longer than this, however, depending upon their scheduling. There will be no charge to you for this procedure. What you should do now: Please call your Yamaha dealer to make a service appointment to have this procedure performed. At that same time, you can find out how long they expect to keep your vehicle for this service. Remember to take this letter with you when you take in your vehicle. You should not operate your motorcycle except to take it to the dealer for inspection and, if required, modification. If you are unable to return to the Yamaha dealer who sold you the vehicle, this service will be performed by any authorized Yamaha Motorcycle dealer. For the name of a dealer near you, call 1-800-88-YAMAHA or visit the Yamaha web site at www.yamaha-motor.com. If you have had this repair performed before you received this letter, you may be entitled to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this repair. Federal regulations require that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within 10 days. If you need help: If, after contacting your dealership, you have questions or concerns which the dealership is unable to answer, please write to: Yamaha Motor Corporation, U.S.A. Customer Relations Department P.O. Box 6555 Cypress, CA 90630 Or call: 1-800-962-7926 If, after contacting Yamaha Customer Relations, you are still not satisfied that we have done our best to remedy the situation without charge and within a reasonable time, you may submit a written complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590; or call the Auto Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to http://www.safercar.gov. Refer to NHTSA recall number xxxxxx. If you no longer own this Yamaha: If you have sold your Ténéré 700 to another party, please call us toll-free at 1-800-962-7926 with the name and address of the new owner, along with the Vehicle Identification Number (VIN) shown above your name on this letter. We’re sorry to cause you any inconvenience, but we are sincerely concerned about your safety and continued satisfaction with our products. Thank you for giving your attention to this important matter. Sincerely, Motorsports Service Support Yamaha Motor Corporation, U.S.A. YAMAHA MOTOR CORPORATION, U.S.A. 6555 Katella Avenue, Cypress, CA 90630-5101 (800)-962-7926
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 23V-472 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Yamaha Motor Corporation, USA Submission Date : JUL 10, 2023 NHTSA Recall No. : 23V-472 Manufacturer Recall No. : 990168 Manufacturer Information : Manufacturer Name : Yamaha Motor Corporation, USA Address : 6555 Katella Avenue Cypress CA 90630-5101 Company phone : 800-962-7926 Population : Number of potentially involved : 211 Estimated percentage with defect : 2 % Vehicle Information : Vehicle 1 : 2022-2022 Yamaha Tenere 700 Vehicle Type : MOTORCYCLES Body Style : OTHER Power Train : GAS Descriptive Information : In affected motorcycles, the front brake calipers may have been assembled with one or more bolts that have an incorrect thread length. Incorrect bolts can cause damage to the mounting hole threads in brake caliper if repeatedly removed and reinstalled, such as during servicing. Then, in the worst case, the bolts would no longer hold the front brake caliper to its mount, so the caliper would detach, resulting in loss of braking ability, increasing the risk of loss of control and a crash with injury or death. Production Dates : JUL 27, 2022 – AUG 29, 2022 VIN Range 1 : Begin : JYADM12Y8NA002428 End : JYADM12Y8NA002638 ✔ Not sequential Description of Defect : Description of the Defect : the front brake calipers may have been assembled with one or more bolts that have an incorrect thread length. Incorrect bolts can cause damage to the mounting hole threads in brake caliper if repeatedly removed and reinstalled, such as during servicing. Then, in the worst case, the bolts would no longer hold the front brake caliper to its mount, so the caliper would detach, resulting in loss of braking ability FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : the bolts would no longer hold the front brake caliper to its mount, so the caliper would detach, resulting in loss of braking ability, increasing the risk of loss of control and a crash with injury or death. Description of the Cause : Vendor supplied the incorrect length (threaded portion) of front brake caliper bolts Part 573 Safety Recall Report 23V-472 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Identification of Any Warning that can Occur : Clunking sound / feel coming from front brake when brake is lightly applied. Difficulty encountered when attempting to remove or reinstall caliper bolts after servicing. Involved Components : Component Name 1 : Bolt, Flang Component Description : Front Brake Caliper Bolt Component Part Number : 90105-10778 Supplier Identification : Component Manufacturer Name : NR Address : NR NR Country : NR Chronology : In June, 2023 Yamaha Motor corporation USA was informed by the manufacturer, Yamaha Motor Co., LTD that such a condition could exist in previously modified units. This was determined pursuant to quality control review, testing and a review of foreign models that use substantially similar part design. Part 573 Safety Recall Report 23V-472 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Remedy : Description of Remedy Program : Affected units must have the length of the front brake caliper mounting bolts confirmed. If found to be incorrect, the bolt(s) must be replaced with correct specification bolt(s) and the mounting-hole threads in the calipers inspected. If the caliper mounting-hole threads(s) are damaged, the caliper must be replaced as well. If customers have already had and paid for this repair to be performed, they may be entitled to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this repair. For more information, contact Yamaha Customer Relations at 1-866-894-1626. Owners should not operate the affected motorcycle, other than to take it to a dealer, until this inspection and, if necessary, modification is performed. How Remedy Component Differs from Recalled Component : Threaded portion of the flange bolt is 20mm. Nominal length is 40mm and bolt is M10x1.25 with a 20mm od. Identify How/When Recall Condition was Corrected in Production : after incorrect bolts were identified, stock was removed from production line and stock was purged. Vendor supplies checked and only correct dimension product has subsequently been provided. Check process has been added to vendor order fulfillment and to receiving QA inspection prior accepting into stock. Recall Schedule : Description of Recall Schedule : We anticipate commencing dealer/consumer notification shortly after the owner’s notification letter is approved by NHTSA, the affected VIN range is ascertained, and the Technical Bulletin’s service procedures are confirmed and finalized by Yamaha staff. assuming the Agency can review and approve the customer notification letter within 5 days of receipt (perhaps July 17th we will have the letter and technical bulletin printed. Normal turnaround time is 3 working days for such a printing. Hence the materials will be ready for mailing approximately March20th. Final copies of these notification documents will be forwarded to the Agency as soon as possible Planned Dealer Notification Date : JUL 20, 2023 – JUL 24, 2023 Planned Owner Notification Date : JUL 20, 2023 – JUL 24, 2023 * NR – Not Reported
**************************************************************************************************************
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END