“This site contains affiliate links for which OEMDTC may be compensated” |
December 20, 2022 NHTSA CAMPAIGN NUMBER: 22V943000
Upper Steering Shaft Connection May Loosen
A loose steering shaft can cause a loss of steering, increasing the risk of a crash.
NHTSA Campaign Number: 22V943
Manufacturer New Flyer of America, Inc.
Components STEERING
Potential Number of Units Affected 746
Summary
New Flyer of America, Inc. (New Flyer) is recalling certain 2013-2022 XDE35, XDE40, XDE60, XE40, XN40, 2017-2022 XE60, 2014-2022 XT40 and XT60 transit buses equipped with a double tilt steering column. The steering column connection to the upper steering shaft may become loose.
Remedy
Dealers will replace the steering column and shaft components, free of charge. Owner notification letters were mailed on February 1, 2023. Owners may contact New Flyer’s customer service at 1-204-224-6706. New Flyer’s number for this recall is R22-035.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
SUBJECT:
Movement in Steering Column to Upper Steering Drive Shaft Joint
ISSUE:
An under torque on the pinch bolt between the steering column & upper steering drive shaft has caused movement and wear in the joint.
SUMMARY:
Torque existing hardware to specification and inspect joints. Remove the steering column & upper steering drive shaft & replace parts if required.
Chronology :
In late November 2022, a customer indicated a “clicking” sound was heard from a steering column November 29, 2022, our Service Representative met with the customer and reviewed the bus in question Over the ensuing days, several more buses were checked, culminating in a fleet check on or about December 06, 2022, which indicated an issue with the upper steering shaft clamping collar to column connection In early December, New Flyer assembled a team to analyze the issue and determine the cause. This team focused on spline engagement, torque value of the pinch-bolt used on the collar of the steering shaft-to-column connection, and steering components
The team ultimately determined the pinch bolt torque was lower than necessary
New Flyer’s Safety Committee met on December 16, 2022, and determined a Safety Recall was warranted, and New Flyer subsequently submitted the recall
74 Affected Products
Vehicles
MAKE | MODEL | YEAR |
NEW FLYER | XDE35 | 2013-2022 |
NEW FLYER | XDE40 | 2013-2022 |
NEW FLYER | XDE60 | 2013-2022 |
NEW FLYER | XE40 | 2013-2022 |
NEW FLYER | XE60 | 2017-2022 |
NEW FLYER | XN40 | 2013-2022 |
NEW FLYER | XT40 | 2014-2022 |
NEW FLYER | XT60 | 2014-2022 |
10 Associated Documents
Recall 573 Report
RCLRPT-22V943-7918.pdf 214.229KB
Defect Notice 573 Report
RCLRPT-22V943-4216.PDF 214.235KB
Recall Acknowledgement
RCAK-22V943-8687.pdf 645.873KB
Remedy Instructions and TSB
RCRIT-22V943-8725.pdf 466.903KB
Recall 573 Report – 1/10/23
RCLRPT-22V943-9816.PDF 214.426KB
Remedy Instructions and TSB
RCRIT-22V943-9488.pdf 161.561KB
ISSUED Owner Notification Letter(Part 577)
RCONL-22V943-2087.pdf 172.388KB
Recall Quarterly Report #1, 2023-1
RCLQRT-22V943-4705.PDF 211.139KB
Recall Quarterly Report #2, 2023-2
RCLQRT-22V943-6575.PDF 211.24KB
Recall Quarterly Report #3, 2023-3
RCLQRT-22V943-7272.PDF 211.459KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V943&docType=RCL
- Durable Ratchet Head: Made from Hardened treated Chrome Vanadium steel alloy (Cr-V) Corrosion-Retardant: Satin Finish. Made in Taiwan
- Easy Storage: A sturdy plastic storage case is included. Non-Slip Grip: Knurled handle
- Easy to Read: High Contrast & Dual Range Scale. Accurate: Pre-Calibrated to ± 4%
- Accessories included: 1/2" Drive 5" long Extension Bar and 1/2" Drive to 3/8" Drive Reducer
- Simple and Reliable: “Click” sound tells the preset torque value is reached. Stop applying force when you hear and feel it.
- PRECISION - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate with traceable serial number.
- DURABLE - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
- LONG-LASTING - Rust & corrosion protection with our unique and newly invented Electro-Black finish treatment.
- PERFORMANCE - Features an easy-to-read, highlighted yellow print dual-range scale. Identify the markings even in low-light conditions.
- COMFORTABLE - Comes with a reversible ratchet head that drives in both directions and measure torque in a clockwise direction.
- ±3% HIGH PRECISION AND COOL APPEARANCE: 1/2 inch drive torque wrench (10-170ft.-lb/13.6-230.5Nm)has a calibration error range of ±3%, high precision, and comes with a corresponding serial number, which is easy to trace the original data, and you can use it with confidence.Hairich torque wrench not only has superior quality but also has a superior appearance. The classic combination of black and red is fashionable and textured, allowing you to enjoy a visual feast during use.
- PREMIUM MATERIAL AND DURABLE: Experience the ultimate durability and antiskid with the torque wrench. The main body of Hairich torque wrench set is made of chrome vanadium steel alloy, which is more strong and more durable. The head of the inch-pound torque wrench adopts a ratchet design with a reversing device to improve work efficiency. The square knurled handle is made of aluminum titanium alloy, which is ergonomic and comfortable to hold for long-time use.
- DUAL SCALE AND QUICK SETTING: Laser Printed by dual-range(ft-lb and Nm). Our professional torque wrench is easy to read and provides direct unit conversion, When the set torque value is reached, the torque wrench will make an audible and felt click to remind you to stop applying force. Pull down the lock knob and hold it until the torque setting is completed. Release the hand, and the lock knob will automatically rebound back to lock the value.
- ERGONOMIC DESIGN AND POWERFUL: Every design of our industrial torque wrench conforms to ergonomic, easy to handle.72-tooth ratchet, 5° ratcheting arc head, a quick-release button for easy loading and unloading, and an aluminum non-slip handle for excellent grip and control. A recent research review that, 72-tooth ratchets are very professional tooth ratchets, you just only rotate 5 degrees to finish it. Not easy to slip and wear, can be used in small spaces, and is more durable and powerful.
- EASY OPERATION AND SAFETY: Thanks to its bidirectional drive ratchet head, our torque wrench can be measured both clockwise and counterclockwise. When the set torque value is reached, a "click" sound will remind you to stop applying force to prevent damage to the item due to excessive torque. Notice: At low Nm settings under 5 Nm the "click" sound can be too light to hear.
- 【High Precision&Quick Reading】: 3/8 torque wrench has high contrast and dual range scale( 5-45 Ft-Lb/6.8-61 Nm),making it clear and easy to read. We have professional torque wrench production technology, and after 20000 tests, the calibration error range of the torque wrench is ± 3%, making it an essential helper for you.
- 【Safe and Reliable Operation】: Equipped with a bidirectional drive ratchet head, torque can be measured clockwise or counterclockwise. When the set torque value is reached, a "click" sound will remind you to stop applying force to prevent damage to the item due to excessive torque.
- 【High Quality and Durable Material】: Made of hardened chromium vanadium steel alloy (Cr-V). At the same time, the bottom buckle tail plug adopts a red anodizing process to improve the product's oxidation resistance during use and enhance surface wear resistance. 72 tooth ratchet head, made of chromium molybdenum steel. High quality materials resist corrosion and are durable.
- 【Quick Torque Setting】: Simple and fast torque setting, pull down the locking knob and hold it down to rotate to the torque you need. Release the hand and the locking knob will automatically rebound to lock the torque value. And the designer referred to the appearance of the flashlight handle and designed a non slip and labor-saving knurled handle, making it more comfortable and easy to hold when using.
- 【Easy to Store and Widely Use】: You will receive the 3/8-inch drive click torque wrench with a sturdy plastic shell storage box, which is very delicate and durable. Torque wrench is suitable nuts and bolts on various occasions, such as bike, motorcycle, car spark, and is the best helper for you🎁. 🔔 And we provide 12 months warranty. If you have any questions, please feel free to contact us.
- 【3Pcs Torque Wrench Set】 The calibration error range is ±3%, each torque wrench has a calibration certificate. The 3-in-1 torque wrench set can meet your different needs. Including 1/4 inch 20-240in.lb, 3/8 inch 5-45ft.lb, 1/2 inch 20-160ft.lb.
- 【Safe & Reliable】 When the 1/2 torque wrench reaches the preset torque value, it makes a clear "click" sound, accompanied by an obvious hand vibration that reminds you no longer to apply force, prevent damage caused. 72-tooth reversible ratchet head, it can be used both clockwise and counterclockwise directions.
- 【Quick Release Button】 This 3/8 torque wrench has a quick release button with which accessories can easily be installed and removed, the accessories can grip and is not easy to fall down. It is more convenient to use. The torque wrench is made of CR-MO with a higher hardness.
- 【Easy to Set】First pull down the locking knob and hold it down and then start setting the desired torque value. Release the hand and the locking knob will automatically rebound to lock the torque value. If you do not use, please set the torque key to the minimal torque value.
- 【Widely Use】The torque wrenches can satisfy you in bicycle, motorcycle, car, truck and wheel screws, wheel nuts and in the device installation, electrical engineering, etc. We provide 12 months warranty. If you have any questions, please feel free to contact us.
- PORTABILITY: Torque wrench 1/2 inch drive has a durable case for portability or storage
- ADDED COMFORT: Bi-material handle for comfort and grip of the 1/2 torque wrench
- HASSLE FREE USE: Locking feature adjusts quick and easily for hassle free use
- QUICK IDENTIFICATION: Scales stamped into housing showing inch and metric torque settings
- Meets or Exceeds ASME Specifications
- 🔧【𝐌𝐢𝐥𝐢𝐭𝐚𝐫𝐲-𝐠𝐫𝐚𝐝𝐞 𝐒𝐭𝐞𝐞𝐥】ETOOLAB torque wrench utilizes military-grade steel as its base material, coupled with professional surface rust protection methods tailored to usage habits. While ensuring user comfort, it enhances product strength, wear resistance, and rust resistance. offers a more comfortable experience and a longer lifespan!
- 👍【𝐄𝐚𝐬𝐲-𝐭𝐨-𝐑𝐞𝐚𝐝】The scale of this 1/2 drive torque wrench is laser-engraved, using a black background with white markings. dinamometrica de 1/2 ensures clear and easy readability of the scale, even in sunlight. With a dual-scale design, users can conveniently read torque values in two different units according to their preferences, without the need for conversion!
- ⚙️【±𝟑% 𝐏𝐫𝐞𝐜𝐢𝐬𝐢𝐨𝐧 & 𝐒𝐢𝐦𝐩𝐥𝐞 𝐋𝐨𝐜𝐤𝐢𝐧𝐠 𝐑𝐢𝐧𝐠】Our torque wrench 1/2 drive meets the high precision standard of ±3% and comes with a traceable serial certificate. You can use it with confidence! Moreover, its graduation ring is tightly locked, with smaller incremental values, ensuring precise and consistent torque output even after multiple uses. This reduces the hassle of frequent adjustments. It is undoubtedly an excellent tool for your work!
- 🔊【𝐋𝐨𝐮𝐝 𝐂𝐥𝐢𝐜𝐤 𝐒𝐨𝐮𝐧𝐝】This torque wrenches has been upgraded to have a louder "Click" sound. We conducted over 25,000 tests to ensure that each product produces a click sound volume of no less than 45dB when the torque value exceeds 34 lbf·ft. When you hear the distinct click sound, it indicates that the preset torque has been reached, signaling you to stop applying force. You no longer need to worry about damaging your mechanical components.
- 💯【𝐔𝐬𝐞𝐫-𝐅𝐫𝐢𝐞𝐧𝐝𝐥𝐲】Our torque wrench set features a 72-tooth dual-directional ratchet head, allowing for easy operation in both clockwise and counterclockwise directions. It is designed with an adjustable locking ring, making it effortless to adjust the preset torque value. Additionally, it includes a quick-release head design, allowing it to replace the wrench head accessories more easily!
- Includes 1-pc. 3/8 in. drive torque wrench; Storage case; Product manual with torque conversion chart
- Wrench emits a click that can be heard and felt when the preset value is reached
- Permanently marked, high-contrast dual-range scale is easy to read, even in low light
- Reversible ratchet head drives in both directions and measures torque in clockwise direction
- Durable all-steel construction has no plastic parts to break or wear out
- Includes 1-pc. 1/4 in. drive micrometer torque wrench (20-200 in.-lb.) with storage case and product manual; 1-pc. 3/8 in. drive micrometer torque wrench (10-80 ft.-lb.) with storage case and product manual; 1-pc. 1/2 in. drive micrometer torque wrench (25-250 ft.-lb.) with storage case and product manual
- Wrenches emit a click that can be heard and felt when the preset value is reached
- Permanently marked, high-contrast dual-range scale is easy to read, even in low light
- Reversible ratchet heads drive in both directions and measure torque in clockwise direction
- Durable all-steel construction has no plastic parts to break or wear out
- 【PRECISION】 - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate . Before shipping, we take 200 times calibration tests to make sure all wrenches performance well .
- 【DURABLE】 - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
- 【 RELIABLE & SAFE】: When small torque wrench set torque value is reached, the wrench will emits slight click sound to remind you to stop applying force to prevent overtorque damage to your items.
- 【LONG-LASTING】 - Rust & corrosion protection with our unique and newly invented Chrome finish treatment.
- 【 DUAL-DIRECTION MEASURES & WIDE USE】: The paddle of the mini torque wrench head can adjust the direction of use at any time,so that the wrench can be used both clockwise and counterclockwise directions. More widely used for Installation equipment, Electrical engineering, bicycle/motorcycle maintenance, Product assembly.With a storage box and an instruction manual.
Last update on 2024-04-11 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-943 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : New Flyer of America, Inc. Submission Date : DEC 20, 2022 NHTSA Recall No. : 22V-943 Manufacturer Recall No. : R22-035 Manufacturer Information : Manufacturer Name : New Flyer of America, Inc. Address : 711 Kernaghan Avenue Winnipeg, MB 00 R2C3T4 Company phone : 204-224-6706 Population : Number of potentially involved : 746 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2013-2022 New Flyer XDE35, XDE40, XDE60, XE40, XE60, XN40, XT40, XT60 Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : NR Descriptive Information : Recall population was based on vehicles using a specific, non-standard steering column, which is a “double tilt” column, allowing a normal tilt function, as well as a function to allow the entire column to pivot away from the dash. Product is isolated to specific customers that require this column type Production Dates : NOV 18, 2013 – DEC 06, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : On certain buses, the steering column to upper steering shaft connection may become loose over time FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : If the steering column and/or steering shaft become loose and worn, loss of steering may occur. Loss of steering increases the risk of a crash. At this time, zero reports of steering loss have been reported Description of the Cause : The torque value on the pinch bolt which clamps the upper steering shaft collar to the column was lower than necessary Identification of Any Warning that can Occur : A “clicking” sound was reported coming from the lower steering column area while turning prior to identifying the issue Part 573 Safety Recall Report 22V-943 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Involved Components : Component Name 1 : Steering column Component Description : COLUMN-STEERING DBL TILT 9204 Component Part Number : 536446 Component Name 2 : Upper steering shaft Component Description : JOINT-U STRG DBL TILT Component Part Number : 532703 Supplier Identification : Component Manufacturer Name : NR Address : NR NR Country : NR Chronology : In late November 2022, a customer indicated a “clicking” sound was heard from a steering column November 29, 2022, our Service Representative met with the customer and reviewed the bus in question Over the ensuing days, several more buses were checked, culminating in a fleet check on or about December 06, 2022, which indicated an issue with the upper steering shaft clamping collar to column connection In early December, New Flyer assembled a team to analyze the issue and determine the cause. This team focused on spline engagement, torque value of the pinch-bolt used on the collar of the steering shaft-to-column connection, and steering components The team ultimately determined the pinch bolt torque was lower than necessary New Flyer’s Safety Committee met on December 16, 2022, and determined a Safety Recall was warranted, and New Flyer subsequently submitted the recall Part 573 Safety Recall Report 22V-943 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Remedy : Description of Remedy Program : New Flyer will check, with appropriate gauges, and replace necessary steering column and shaft components, and re-torque affected pinch bolts. In the event material supply becomes a constraint, there are secondary plans to permanently attach the column-to-shaft connection through welding of the components How Remedy Component Differs from Recalled Component : Once components are replaced or verified, the additional torque application to the pinch bolt would prevent further issues. If the secondary plans are executed, the permanent attachment would also prevent further issues. Identify How/When Recall Condition was Corrected in Production : When the torque was identified as suspect, engineering release a change notice to require the torque increase. The change release was implemented on affected buses in our manufacturing plants, prior to customer delivery Recall Schedule : Description of Recall Schedule : A draft recall letter will be provided for review, and owner letters will be issued within approx. 3 weeks of NHTSA approval of the draft, but not more than 60 days after this recall submission. Please note as New Flyer does not have a dealer network, dates entered are simply to line up with customer notification Planned Dealer Notification Date : FEB 13, 2023 – FEB 17, 2023 Planned Owner Notification Date : FEB 13, 2023 – FEB 17, 2023 * NR – Not Reported
**************************************************************************************************************
THIS ITS DOCUMENT SHOULD BE RETAINED AND REFERRED TO FOR FUTURE MAINTENANCE UNTIL THE NEW FLYER PARTS AND/OR SERVICE MANUAL IS UPDATED TO REFLECT WORK DONE AS A RESULT OF THIS DOCUMENT. ENSURE THAT THIS DOCUMENT IS AVAILABLE FOR PARTS AND MAINTENANCE STAFF GOING FORWARD. This document and the contents discussed herein are the confidential and proprietary information of New Flyer Industries Canada ULC and New Flyer of America Inc. and are disclosed by New Flyer in confidence. This document and the contents herein are not to be disclosed by the intended recipient without the prior written authorization of New Flyer. Any unauthorized disclosure, reproduction or other distribution of this document or information strictly prohibited and may result in action being taken against the party making the unauthorized disclosure. This document and all copies hereof must be returned to New Flyer upon request. INSTRUCTION TO SERVICE ITS: 60596 December 21, 2022 SECTION: 350-Driver’s Controls WRITTEN BY: Troy Stutsky SUBJECT: Movement in Steering Column to Upper Steering Drive Shaft Joint ISSUE: An under torque on the pinch bolt between the steering column & upper steering drive shaft has caused movement and wear in the joint. SUMMARY: Torque existing hardware to specification and inspect joints. Remove the steering column & upper steering drive shaft & replace parts if required. ITS60596 Ref. NHTSA Recall No. Ref. Transport Canada Recall No. 22V-943 2022-732 INSTRUCTION TO SERVICE ITS60596 ITS60596 Page 2 of 9 December 21, 2022 NOTE: Please note, New Flyer will allow the use of a combination of new parts, existing parts and / or welded parts as long as they meet the requirements that are outlined in the procedures written in this document ITS-60596. PROCEDURE: 1. Set park brake and chock wheels. 2. Turn the main battery disconnect switch to the “OFF” position. 3. On the steering assembly of the bus with the steering assembly still installed in the bus, please torque the hardware in the four locations shown in Figure 1 to 70±4Ft/Lbs dry. Please ensure that the bolts are 7/16” – 20 X 2.00”; Grade 8; Zinc (NF PN 6444255) & the nuts are 7/16” – 20; Self Locking; Zinc (NF PN 6444254). If any 10MM hardware is found in any of these four locations it should be removed and replaced. Remove existing torque witness marks and re-mark after new torque has been applied. Figure 1: Locations to Torque on Steering System 1 2 3 4 INSTRUCTION TO SERVICE ITS60596 ITS60596 Page 3 of 9 December 21, 2022 4. After the new torque has been applied, inspect for any free play at the splined, torqued joint between the steering column and the upper steering drive shaft, which is identified as Area #1 in Figure 1, by grasping the drive shaft mid-length and applying a lateral force. There should be no free play in this torqued joint. If no free play has been found, the bus is safe to return to service. 5. If free play is found at the splined, torqued joint between the steering column and the upper steering drive shaft, which is identified as Area #1 in Figure 1, please proceed to remove the steering column & upper steering drive shaft from the bus for closer inspection on the shop bench. 6. With the steering column and the upper steering drive shaft removed from the bus and on the bench, please separate the steering column from the upper steering drive shaft. 7. Using the PSS Go/No Go Plug tool measure the solid, splined end of the upper steering drive shaft. See Figure 2. a. If the Go/No Go Plug will not fit into the splined portion of the drive shaft, the upper steering drive shaft is a pass and can be reused as required. b. If the Go/No Go Plug does fit into the splined portion of the drive shaft, the upper steering drive shaft is a fail and will need to be safely stored for using in a welded assembly if required. Figure 2: Upper Steering Shaft Measurement 8. Using the No Go Gauge measure the splined end of the steering column. See Figure 3. a. If the No Go Gauge will not fit over the splined portion of the steering column, the steering column is a pass and can be reused as required. b. If the No Go Gauge does fit over the splined portion of the steering column, the steering column is a fail and will need to be safely stored for using in a welded assembly if required. Upper Steering Drive Shaft Go/No Go Plug Tool Splines to Measure INSTRUCTION TO SERVICE ITS60596 ITS60596 Page 4 of 9 December 21, 2022 Figure 3: Steering Column Measurement 9. Any combination of new or used parts that are available and that have deemed as a pass using the above Go / No Go measurements can be used to repair the buses. When refastening the verified good upper steering drive shafts to the verified good steering columns please use new hardware bolt 7/16” – 20 X 2.00”; Grade 8; Zinc (NF PN 6444255) & nut 7/16” – 20; Self Locking; Zinc (NF PN 6444254) at the joint between the upper steering drive shaft and the steering shaft shown in Figure 4. Torque the hardware to 70±4Ft/Lbs dry. Remove existing torque witness marks and re-mark after new torque has been applied. 10. Re-install the steering column with upper steering drive shaft back into the bus. Torque the hardware where the upper steering drive shaft fastens to the miter box to 70±4Ft/Lbs dry. Remove existing torque witness marks if required and re-mark after new torque has been applied. The bus is safe to return to service. 11. The steering columns and upper steering drive shafts that were deemed to be failed, as tested by the Go / No Go measurements, may be used together as a welded assembly as required. To weld together one steering column and one upper steering drive shaft, please follow the instructions in Appendix A with welding procedure data sheet provided in Appendix B. NOTE: When welding the steering colum and the upper drive shaft please place heat sinks next to the steering column bearing, adjacent to the weld area, to prevent the heat from traveling further up the steering column to protect any adjacent components. Copper or aluminum blocks would be great options. No Go Gauge Steering Column Splines to Measure INSTRUCTION TO SERVICE ITS60596 ITS60596 Page 5 of 9 December 21, 2022 NOTE: When pre-heating the steel to 200F before welding, a digital temperature gun or temperature stick rated to 200F should be used. NOTE: Given that one of the steels being welded is 1141, we request an MPI inspection on the first 10 welded assemblies and if all 10 are OK then complete 1 in 10 for the remainder. 12. When the steering column and upper steering drive shaft welded assy is complete and has passed MPI inspection it can be re-installed in the bus. Torque the hardware where the upper steering drive shaft fastens to the miter box to 70±4Ft/Lbs dry. Remove existing torque witness marks if required and re-mark after new torque has been applied. The bus is safe to return to service. 13. After any procedure has been completed please clean up all tools and debris and return the bus to service condition. 14. Turn the main battery disconnect switch to the “ON” position. INSTRUCTION TO SERVICE ITS60596 ITS60596 Page 6 of 9 December 21, 2022 LABOUR ESTIMATE Operation Number of Technician(s) Hours Labor Time T X HR 1 Torque existing hardware to specification and inspect joints 2 0.5 1.0 2 Remove and replace the steering column & upper steering drive shaft if required 2 1.5 3.0 PARTS REQUIRED Item Part Number Description Qty. per Coach Units Notes 1 536446 COLUMN-STEERING DBL TILT 9204 1 EA If Required 2 6447692 STEERING COLUMN, SERVICE ASSEMBLY 1 EA If Required 3 532703 JOINT-U STRG DBL TILT 1 EA If Required 4 068035 BOOT TAPERED 1.56&4.5ID 1 EA If Required 5 50S00016 SCREW FH CROSS RECESS TPG. TYPE AB #10 X 1″ LG. 4 EA If Required 6 004944 SCREW-TPG CSK 10-32X1.0LG 2 EA If Required 7 6444255 BOLT, HEX 7/16″ – 20 UNF X 2″ LG. 4 EA If Required 8 6444254 NUT, HEX 7/16″ – 20 UNF 4 EA If Required SPECIAL TOOLS REQUIRED Item Part Number Description Qty. Units Notes 1 NPN Welding Wire 0.01 EA If Required 2 NPN Welding Gas 0.01 EA If Required 3 NPN Torque Paint Marker 0.01 EA If Required INSTRUCTION TO SERVICE ITS60596 ITS60596 Page 7 of 9 December 21, 2022 Appendix A INSTRUCTION TO SERVICE ITS60596 ITS60596 Page 8 of 9 December 21, 2022 Appendix A Continued… INSTRUCTION TO SERVICE ITS60596 ITS60596 Page 9 of 9 December 21, 2022 Appendix B
**************************************************************************************************************
_________________________________________________________________________________________________________________ TSIB 22-13 Rev. A Page 1 of 1 December 19, 2022 TECHNICAL SERVICE INFORMATION BULLETIN TSIB 22-13 Rev A December 19, 2022 TO: Affected Operators TITLE: Torque value changes to splined joints in the steering system. APPLICABILITY: New Flyer Xcelsior buses equipped with double tilt steering columns. This TSIB will provide an updated recommendation for torque of hardware used to secure the splined joints in in the steering system between the steering column and the gearbox. For customers operating New Flyer Xcelsior buses equipped with double tilt steering columns, it is New Flyer’s recommendation that, at the next maintenance interval, the torque in the four locations depicted in the diagram be increased from 50 ft-lb to 70 ft-lb ± 4 ft-lb. Direct all inquiries regarding this bulletin to: Kevin Robinson, CET Technical Services Manager C 204.430.8826 kevin_robinson@newflyer.com New Flyer
**************************************************************************************************************
IMPORTANT SAFETY RECALL NOTICE 01-February-2023 VIA US First Class Mail Sound Transit ATTN: Tim Wagner 401 S Jackson St Seattle, WA 98104 Subject: Motor Vehicle Safety Recall 22V-943 Steering Column/Upper Steering Shaft To whom it may concern: This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. New Flyer of America Inc. (New Flyer) has decided that a defect which relates to motor vehicle safety exists on specific vehicles equipped with a “double tilt” steering column. New Flyer has determined that the following vehicles, operated by Sound Transit are affected by this recall action: Make: New Flyer Heavy Duty Urban Transit Bus Model: XDE60 VIN Fleet # Model Model Year 5FYH8YU09LB073879 9660 XDE60 2020 5FYH8YU05LB073880 9661 XDE60 2020 5FYH8YU07LB073881 9662 XDE60 2020 5FYH8YU09LB073882 9663 XDE60 2020 5FYH8YU00LB073883 9664 XDE60 2020 5FYH8YU02LB073884 9665 XDE60 2020 5FYH8YU04LB073885 9666 XDE60 2020 5FYH8YU06LB073886 9667 XDE60 2020 5FYH8YU08LB073887 9668 XDE60 2020 5FYH8YU0XLB073888 9669 XDE60 2020 5FYH8YU01LB073889 9670 XDE60 2020 5FYH8YU08LB073890 9671 XDE60 2020 5FYH8YU0XLB073891 9672 XDE60 2020 5FYH8YU01LB073892 9673 XDE60 2020 5FYH8YU03LB073893 9674 XDE60 2020 5FYH8YU05LB073894 9675 XDE60 2020 5FYH8YU07LB073895 9676 XDE60 2020 5FYH8YU09LB073896 9677 XDE60 2020 5FYH8YU00LB073897 9678 XDE60 2020 5FYH8YU02LB073898 9679 XDE60 2020 VIN Fleet # Model Model Year 5FYH8YU04LB073899 9680 XDE60 2020 5FYH8YU07LB073900 9681 XDE60 2020 5FYH8YU09LB073901 9682 XDE60 2020 5FYH8YU00LB073902 9683 XDE60 2020 5FYH8YU02LB073903 9684 XDE60 2020 5FYH8YU04LB073904 9685 XDE60 2020 5FYH8YU06LB073905 9686 XDE60 2020 5FYH8YU08LB073906 9687 XDE60 2020 5FYH8YU0XLB073907 9688 XDE60 2020 5FYH8YU01LB073908 9689 XDE60 2020 5FYH8YU03LB073909 9690 XDE60 2020 The double-tilt column used in the affected vehicles has been found to have wear between the steering column and upper steering shaft connection. This wear has been determined to be due to a lower than necessary torque value on the pinch bolt of the steering shaft collar. This reduced clamp force from the pinch bolt may allow wear, over time, which may cause the spline engagement between the 2 components to further loosen and allow slipping in the connection. (Preceding potential slippage of the steering components, an audible sound described as a “clicking” may be noticed.) This slipping could cause a loss of steering control. A loss of steering control increases the potential for a vehicle crash and injury. New Flyer will check the steering column and upper steering shaft splines to verify no excessive wear, replace components as necessary, and re-torque the pinch bolt on the steering shaft collar on the above vehicles at no cost. Please contact your Regional Product Support Manager to coordinate the recall action. New Flyer anticipates that the repairs to correct the issue will take approximately 0.5 – 1.5 hours/bus. If you are a lessor of vehicles which are affected, it is required that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days. If you no longer own this vehicle, or it has been removed from operation permanently, please inform the undersigned. If you had this corrective action performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. If New Flyer is unable to correct this defect within a reasonable time, you may submit a written complaint to the: Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave. SE, Washington, DC, 20590, Or call 1-888-327-4236 (TTY: 1-800-424-9153); or go to http://www.safercar.gov. We regret any inconvenience which this action may cause you. However, we are concerned about the safety of your passengers and employees. Thank you for your attention to this important matter. Sincerely, NEW FLYER OF AMERICA INC. By: Jim Johnson Vehicle Safety & Regulatory Compliance Manager (256) 453-7181 cc (email): Scott Halbesma – Vice President, Customer Care Kevin Hiemenz – Regional Director Joe Jonak – Regional Product Support Manager
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-943 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : New Flyer of America, Inc. Submission Date : JAN 10, 2023 NHTSA Recall No. : 22V-943 Manufacturer Recall No. : R22-035 Manufacturer Information : Manufacturer Name : New Flyer of America, Inc. Address : 711 Kernaghan Avenue Winnipeg, MB 00 R2C3T4 Company phone : 204-224-6706 Population : Number of potentially involved : 746 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2013-2022 New Flyer XDE35, XDE40, XDE60, XE40, XE60, XN40, XT40, XT60 Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : NR Descriptive Information : Recall population was based on vehicles using a specific, non-standard steering column, which is a “double tilt” column, allowing a normal tilt function, as well as a function to allow the entire column to pivot away from the dash. Product is isolated to specific customers that require this column type Production Dates : NOV 18, 2013 – DEC 06, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : On certain buses, the steering column to upper steering shaft connection may become loose over time FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : If the steering column and/or steering shaft become loose and worn, loss of steering may occur. Loss of steering increases the risk of a crash. At this time, zero reports of steering loss have been reported Description of the Cause : The torque value on the pinch bolt which clamps the upper steering shaft collar to the column was lower than necessary Identification of Any Warning that can Occur : A “clicking” sound was reported coming from the lower steering column area while turning prior to identifying the issue Part 573 Safety Recall Report 22V-943 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Involved Components : Component Name 1 : Steering column Component Description : COLUMN-STEERING DBL TILT 9204 Component Part Number : 536446 Component Name 2 : Upper steering shaft Component Description : JOINT-U STRG DBL TILT Component Part Number : 532703 Supplier Identification : Component Manufacturer Name : Douglas Autotech Coporation Address : 300 Albers Road Bronson Michigan 49028 Country : United States Chronology : In late November 2022, a customer indicated a “clicking” sound was heard from a steering column November 29, 2022, our Service Representative met with the customer and reviewed the bus in question Over the ensuing days, several more buses were checked, culminating in a fleet check on or about December 06, 2022, which indicated an issue with the upper steering shaft clamping collar to column connection In early December, New Flyer assembled a team to analyze the issue and determine the cause. This team focused on spline engagement, torque value of the pinch-bolt used on the collar of the steering shaft-to-column connection, and steering components The team ultimately determined the pinch bolt torque was lower than necessary New Flyer’s Safety Committee met on December 16, 2022, and determined a Safety Recall was warranted, and New Flyer subsequently submitted the recall Part 573 Safety Recall Report 22V-943 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Remedy : Description of Remedy Program : New Flyer will check, with appropriate gauges, and replace necessary steering column and shaft components, and re-torque affected pinch bolts. In the event material supply becomes a constraint, there are secondary plans to permanently attach the column-to-shaft connection through welding of the components If the owner performs the work, New Flyer will provide replacement parts and reimburse labor costs associated with this correction through our warranty process. In the event a customer has made similar repairs within approx. 12 months prior to this recall, New Flyer will reimburse through our warranty process How Remedy Component Differs from Recalled Component : Once components are replaced or verified, the additional torque application to the pinch bolt would prevent further issues. If the secondary plans are executed, the permanent attachment would also prevent further issues. Identify How/When Recall Condition was Corrected in Production : When the torque was identified as suspect, engineering release a change notice to require the torque increase. The change release was implemented on affected buses in our manufacturing plants, prior to customer delivery Recall Schedule : Description of Recall Schedule : A draft recall letter will be provided for review, and owner letters will be issued within approx. 3 weeks of NHTSA approval of the draft, but not more than 60 days after this recall submission. Please note as New Flyer does not have a dealer network, dates entered are simply to line up with customer notification Planned Dealer Notification Date : FEB 13, 2023 – FEB 17, 2023 Planned Owner Notification Date : FEB 13, 2023 – FEB 17, 2023 * NR – Not Reported
SEOCONTENT-END