Marking the Center Point for the Rear of the Vehicle
45.

Place the laser level approximately 800 mm (31.5 in.) from the rear of the vehicle and
align the laser with the center mark at the front of the vehicle and the middle of the
rear camera, as shown in Figure 66 and Figure 67.

Front center
mark

Laser level

Laser line

Figure 65

Rear
camera

Rear camera

Figure 67

Figure 66

34/67

NTB25-002

46.

Mark the rear fascia, where shown in Figure 68, and the floor near the rear fascia.
Mark

Mark

Figure 68

47.

Move the laser so it is about 45° and approximately 800 mm (31.5 in.) from the rear of
the vehicle, and then line up the vertical laser line to the mark on the rear fascia.
HINT: The laser level can be either to the left or right of the rear of the vehicle.
Mark

Laser
line

Figure 69

35/67

NTB25-002

48.

Mark the floor with a cross-mark, denoting the center point of the rear of the vehicle.
Rear center
point

Cross-mark

Figure 71

Figure 70

36/67

NTB25-002

Placing Calibration Targets for the Front and/or Rear Cameras
IMPORTANT: Steps 49 - 63 and the related figures show the rear of the vehicle. The front
is similar. If the AVM Control Module was replaced, steps 49 - 63 must be performed for
both the front and rear cameras.
49.

Place the laser level 2500 mm from the rear center point of the vehicle, and then align
the laser line with both the front and rear center points, as shown in Figure 72 and
Figure 73.

Laser line

Front
center point

Laser level
2500 mm
Rear center
point

Laser line

Figure 72

2500 mm from
rear center
point of vehicle

Figure 73

37/67

NTB25-002

50.

Place a cross-mark on the floor below the laser line (Figure 74).

Cross-mark

Figure 74

38/67

NTB25-002

51.

Measure and place a mark 500 mm from the rear center point.

Front
center
point
Mark
500 mm

Rear
center
point

Figure 75

Rear center
point
Mark 500 mm
from rear
center point

Figure 76
39/67

NTB25-002

52.

Measure and place a mark 2500 mm to the left and to the right of the laser level, as
shown in Figure 77, Figure 78 and Figure 79.


Laser not shown in Figure 79.

Mark
2500 mm
2500 mm

Mark
Figure 77

Mark 2500
mm from
center point

Mark 2500
mm from
center point

Cross-mark
2500 mm
from rear
center point

Figure 79

Figure 78

40/67

NTB25-002

53.

Move the laser to the 500 mm mark, and then measure and place a mark 2500 mm to
the left and to the right of the laser level, as shown in Figure 80 and Figure 81.

2500 mm
2500 mm

Figure 80

Figure 81

41/67

NTB25-002

54.

Use a chalk line tool to make a line between the 500 mm and 2500 mm marks, as
shown in Figure 82 and Figure 83.

2500 mm
chalk line

500 mm chalk
line
Figure 82

500 mm chalk
line

2500 mm
chalk line

Figure 83

42/67

NTB25-002

55.

Place the laser level with both vertical lines activated, and align one laser line with the
500 mm chalk line and align the other laser line to the front and rear center point of
the vehicle, as shown in Figure 84.
IMPORTANT: The laser line must be perfectly aligned with the 500 mm chalk line and
the front and rear center points.

500 mm chalk
line

2500 mm
chalk line

Figure 84
56.

Place a cross-mark on the floor below the laser line (Figure 85).

500 mm
chalk line

Cross-mark

Figure 85
43/67

NTB25-002

57.

Measure and mark 1000 mm increments, as shown in Figure 86 and Figure 87.
500 mm chalk
line
1000mm
1000mm
1000mm
1000mm

2500 mm
chalk line
Figure 86

1000 mm
marks

500 mm
chalk line

1000 mm
marks

Figure 87
44/67

NTB25-002

58.

Move the laser level to the position shown in Figure 88, and then make a mark on the
2500 mm chalk line, as shown in Figure 88 and Figure 89.
IMPORTANT: The laser line must be perfectly aligned with the 500 mm chalk line.

500 mm chalk
line
2500 mm
chalk line

Mark
Figure 88

Laser level
500 mm chalk
line

2500 mm
chalk line
Mark
Figure 89

45/67

NTB25-002

59.

Move the laser level to the position shown in Figure 90, and then make a mark on the
2500 mm chalk line, as shown in Figure 90 and Figure 91.
IMPORTANT: The laser line must be perfectly aligned with the 500 mm chalk line.

Mark

2500 mm
chalk line
500 mm chalk
line
Figure 90
Laser level
500 mm chalk
line

2500 mm
chalk line
Mark

Figure 91

46/67

NTB25-002

60.

Using a carpenter’s square, squared to the chalk line, extend each of the seven (7)
marks 12 in. from the chalk line.

Chalk
line

Mark

Carpenter’s
square
12
inches

Figure 92

500 mm chalk
line

2500 mm
chalk line

Extend these marks

Figure 93

47/67

NTB25-002

61.

Place five (5) targets on the marks along the 500 mm chalk line.
IMPORTANT: Orient and align the targets, as shown in Figure 94, Figure 95, and
Figure 96. The targets must be aligned with the 500 mm chalk line and the marks
made in step 60 on page 47.

Align

Align

500 mm chalk
line
Align

Mark

Figure 94

Figure 95

Figure 96
48/67

NTB25-002

62.

Place one (1) target on the driver (LH) side mark on the 2500 mm chalk line.
IMPORTANT: Orient and align the target, as shown in Figure 97, Figure 98, and
Figure 99. The target must be aligned with the 2500 mm chalk line and the marks
made in step 60 on page 47.
Align

Mark

Align

Align

2500 mm
chalk line
Figure 97

Figure 98

Figure 99

49/67

NTB25-002

63.

Place one (1) target on the passenger (RH) side mark on the 2500 mm chalk line.
IMPORTANT: Orient and align the target, as shown in Figure 100, Figure 101, and
Figure 102. The target must be aligned with the 2500 mm chalk line and the marks
made in step 60 on page 47.

Align

Mark

Align

Align

2500 mm
chalk line
Figure 100

Figure 101

Figure 102

50/67

NTB25-002

64.

If the front camera was replaced, repeat steps 49 - 63 starting on page 37, to place
the calibration targets for the front camera.

65.

Measure 200 mm and 283 mm from the center point of the driver (LH) side rear
wheel, and then make a mark at each measurement, as shown in Figure 103.

200 mm

283 mm

Figure 103

66.

Measure 200 mm and 283 mm from the center point of the passenger (RH) side rear
wheel, and then make a mark at each measurement, as shown in Figure 104.

283 mm

200 mm

Figure 104
51/67

NTB25-002

Rear Camera Calibration Measurements
IMPORTANT: All measurements must be in millimeters (mm). Refer to the illustrations in
Figure 109 on page 54 to ensure the correct measurement is documented in the correct
order and for each calibration target.
67.

Measure the distance between the center point of the driver (LH) side rear wheel to
the center of the calibration target T1, and then document that distance as L1 in
Figure 109 on page 54.