NOTE: After leaving a saved location, the suspension automatically lowers. However, it may not lower until
CybertruckModel SModel X meets the speed and distance threshold at which the suspension lowers.
NOTE: If CybertruckModel SModel X reaches a saved location and the existing suspension setting is already higher than the
level that has been saved for that location, the ride height is not adjusted.
To remove an auto-raising location

If you do not want the suspension to automatically raise at a location, touch to deselect Always Auto-Raise at This Location in
the popup that appears when you arrive at a saved location.
Self-Leveling
CybertruckModel SModel X equipped with air suspension automatically self-levels, even when power is off. To prevent
damage when jacking or lifting the vehicle, you must activate Jack Mode to disable self-leveling (press the brake pedal and
touch Controls > Service > Jack Mode). For more details, see Jack Mode on page 525.

270

Owner's Manual

Owners Manual
Air Suspension
NOTE: When CybertruckModel SModel X starts, you may hear the sound of the compressor as the air suspension system’s
reservoir fills with air.
Air suspension offers a superior ride quality and when carrying loads, the system maintains a level height between the front
and rear. You can manually adjust the ride height to suit your circumstances (for example, you can raise
CybertruckModel SModel X when driving at low speeds when you need extra ground clearance, such as when driving on a
steep driveway or ramp, in deep snow, over large speed bumps, parking curbs, etc.).
If a fault is detected that reduces the performance of the air suspension system, a yellow indicator lights up on
the instrument panel. If the problem persists, contact Tesla.

If a fault is detected that disables the air suspension system, a red indicator lights up on the instrument panel.
Contact Tesla.

Adjusting Ride Height
CAUTION: Before adjusting the suspension height, ensure CybertruckModel SModel X is clear of all obstacles, above
and below.
You can manually adjust the ride height by pressing the brake pedal touching Controls > Suspension on the touchscreen. The
ride height settings that are available depend on your driving speed and other conditions (for example, the suspension does
not lower if a door is open). The touchscreen also displays the approximate ground clearance for each setting. Drag the slider
to choose from these options:
• Very High. When set to Very High, the suspension automatically lowers to High when driving speed reaches 22 mph
(35 km/h).
• High. When set to High, the suspension automatically lowers to Standard when driving speed reaches 34 mph (55 km/h).
• Standard. The Standard setting ensures optimum comfort and handling under all loading conditions.
• Low. Lowering the height can improve aerodynamics and make it easier to load or unload cargo and passengers.
CAUTION: Avoid driving aggressively (hard accelerations, sharp turns, etc.) when the suspension is set to High or Very
High. Doing so can cause vibration and increase the possibility of damage.
CAUTION: Acceleration may be reduced when the suspension is set to High or Very High.
Auto-Raising Suspension
Auto-raising suspension saves you from manually having to raise the suspension every time you arrive at a frequently-used
location where you have previously raised the suspension. The location is automatically saved whenever you raise the
suspension to High or Very High. When you return to the saved location, CybertruckModel SModel X raises the suspension
and the instrument panel displays a message indicating that the suspension is being raised.
After leaving a saved location, the suspension automatically lowers. However, it may not lower until
CybertruckModel SModel X meets the speed threshold at which the suspension lowers.
NOTE: When returning to a saved location and driving faster than the High and Very High suspension settings allow, the
suspension does not raise until CybertruckModel SModel X slows down.
NOTE: If CybertruckModel SModel X reaches a saved location and the existing suspension setting is already higher than the
level that has been saved for that location, the ride height is not adjusted.

Owner's Manual

271

Owners Manual
To remove an auto-raising location

If you do not want the suspension to automatically raise at a location, touch the X in the auto-raising status message that
displays at a saved location. By doing so, the suspension does not automatically raise at the location.
Self-Leveling
CybertruckModel SModel X equipped with air suspension automatically self-levels, even when power is off. To prevent
damage when jacking or lifting the vehicle, you must activate Jack Mode to disable self-leveling (press the brake pedal and
touch Controls > Service > Jack Mode). For more details, see Jack Mode on page 525.

272

Owner's Manual

Owners Manual
Cruise Control
Cruise control makes it easy to maintain a consistent driving speed. Cruise control is primarily intended for driving on dry,
straight roads, such as highways. It should not be used on city streets and in heavy traffic.
Operating Cruise Control
WARNING: Do not use cruise control on winding or slippery road surfaces, or when traffic conditions make it unsafe to
drive at a consistent speed.
1. If there is a button on the end of your cruise stalk, press the button to turn the cruise control system on or off. An orange
light is illuminated if the system is on.
2. Accelerate manually until you reach your desired cruising speed.
NOTE: Cruise control will not activate below 18 mph (29 km/h).
3. Move the cruise stalk up or down, then release.

Owner's Manual

273

Owners Manual

Cruise control is now active.
The instrument cluster displays a gray speedometer icon to show your set speed.

The instrument panel displays the CRUISE message above the speedometer and an arrow displays on the
speedometer to show your set speed.

You can manually accelerate past the set speed at any time when cruise control is active. However, when you release the
accelerator, CybertruckModel SModel X slows down to the set speed.
WARNING: Driving downhill can increase driving speed, causing CybertruckModel SModel X to exceed your cruising
speed.
Changing the Cruising Speed
Move the cruise stalk up (increase) or down (decrease) until your desired cruising speed is reached.
• Move the cruise stalk up or down to the first position and release to increase/decrease the set speed by 1 mph.
• Move the cruise stalk up/down to the second position and release to increase/decrease the set speed by 5 mph.
• Hold the cruise stalk up or down to increase/decrease the cruising speed and set speed simultaneously.

274

Owner's Manual

Owners Manual

Owner's Manual

275

Owners Manual

NOTE: It may take a few seconds for CybertruckModel SModel X to reach the new set speed.
Canceling and Resuming
If equipped, press the button on the end of the cruise stalk to turn the cruise control system off (which will cancel cruise
control and clear the set speed).
You can cancel cruise control if you do any of the following:
• Press the brake pedal.
• Push the cruise stalk away from you.
NOTE: Canceling cruise control does not clear the set speed until CybertruckModel SModel X powers off.
NOTE: When cruise control cancels, CybertruckModel SModel X does not coast. Instead, regenerative braking slows down
CybertruckModel SModel X in the same way as when you move your foot off the accelerator when driving without cruise
control (see Regenerative Braking on page 262).
To resume cruising at the previous set speed, briefly pull the cruise stalk toward you. Cruise control resumes, provided your
driving speed is over 18 mph (29 km/h).

276

Owner's Manual

Owners Manual

To resume cruising at the current driving speed, move the cruise stalk up or down, then release.

Owner's Manual

277

Owners Manual

278

Owner's Manual

Owners Manual
Park Assist
CybertruckModel SModel X is designed to detect the presence of objects. When driving slowly (for example, when parking),
the vehicle alerts you if an object is detected in close proximity of your CybertruckModel SModel X. The vehicle alerts you
when objects are detected in front of CybertruckModel SModel X when you are in Drive, and behind
CybertruckModel SModel X when you are in Reverse.
WARNING: You may not be alerted if CybertruckModel SModel X rolls freely in the opposite direction (for example, Park
Assist does not display an alert if CybertruckModel SModel X rolls backwards down a hill while in Drive).
NOTE: Depending on date of manufacture and options selected at time of purchase, some Model S vehicles are not equipped
with the parking sensors.
WARNING: The Park Assist images provided below are representative only. The exact number and location of sensors
may vary depending on the date your CybertruckModel SModel X was manufactured.

Owner's Manual

279

Owners Manual

280

Owner's Manual

Owners Manual

Owner's Manual

281

Owners Manual

282

Owner's Manual

Owners Manual

Owner's Manual

283

Owners Manual

NOTE: Park Assist may be disabled when a bicycle is detected or CybertruckModel SModel X is in trailer mode.
WARNING: Never depend on Park Assist to inform you if an area you are approaching is free of objects and/or people.
Several external factors can reduce the performance of Park Assist, causing either no readings or false readings (see
Limitations and False Warnings on page 286). Therefore, depending on Park Assist to determine if
CybertruckModel SModel X is approaching an obstruction can result in damage to the vehicle and/or objects, and can
potentially cause serious injury. Always inspect the area with your own eyes. When reversing, perform shoulder checks
and use all mirrors. Park assist does not detect children, pedestrians, bicyclists, animals, or objects that are moving,
protruding, located too far above or below the sensors or cameras, or too close or too far from the sensors or cameras.
Park Assist is for guidance purposes only and is not intended to replace your own direct visual checks. It is not a
substitute for careful driving.
Tesla Vision Park Assist
NOTE: Depending on market region, vehicle configuration, options purchased, and software version, your vehicle may not be
equipped with Tesla Vision Park Assist.
Your vehicle uses the cameras mounted on the front, rear, and sides of CybertruckModel SModel X to create a high-fidelity
reproduction of surrounding objects on the instrument clustertouchscreen.

284

Owner's Manual

Owners Manual

The colors on the visualization correspond to the distance between CybertruckModel SModel X and the object shown. Red is
closer to CybertruckModel SModel X, and yellow is farther from CybertruckModel SModel X.
You can enable or disable Tesla Vision Park Assist by touching Controls > Autopilot, scrolling to Park Assist, and toggling
between Standard and Tesla Vision.
NOTE: Enabling Tesla Vision Park Assist disables Lane Assist visualizations. For more information, see Lane Assist on page
400.
Visual and Audio Feedback
When you shift to Reverse, the Park Assist view displays on the left side of the instrument panel, showing objects that are in
close proximity to the front and rear of CybertruckModel SModel X. This view closes when you shift into Drive unless an
object is detected close to the front of CybertruckModel SModel X, in which case the Park Assist view closes automatically
when you start driving faster than the speed at which Park Assist operates. When reversing, visual feedback also displays on
the touchscreen (see Rear Facing Camera(s) on page 306). You can manually close the park assist view on the touchscreen by
touching the X.
When driving at low speeds with the Camera app displayed on the touchscreen, you can switch to the Park Assist view by
touching the button located in the upper left corner of the Camera app screen. This is useful if you need assistance with
parallel parking.
If chimes are turned on (see Controlling Audible Feedback on page 286), an audible beep sounds as you approach an object.
You can temporarily mute the chime by touching the speaker icon on the bottom corner of the Park Assist view.
NOTE: If Park Assist is unable to provide feedback, the instrument panel displays an alert message.
CAUTION: Keep sensors and cameras clean from dirt, debris, snow, and ice. Avoid using a high pressure power washer
on the sensors and cameras, and do not clean a sensor or camera with a sharp or abrasive object that can scratch or
damage its surface.

Owner's Manual

285

Owners Manual
CAUTION: Do not install accessories or stickers on or near the sensors or cameras.
Controlling Audible Feedback
You can use Park Assist with or without audible feedback. To turn chimes on or off, touch Controls > Safety > Park Assist
Chimes.
To mute the chimes temporarily, touch the speaker icon in the bottom corner of the Park Assist view. The chimes are muted
until you shift or drive over the speed at which Park Assist operates.
Limitations and False Warnings
Park Assist may not function correctly in these situations:
• One or more of the sensors or cameras is damaged, dirty, or obstructed (such as by mud, ice, or snow, or by a vehicle bra,
excessive paint, or adhesive products such as wraps, stickers, rubber coating, etc.).
• The object is located below approximately 8 inches (20 cm) (such as a curb or low barrier).
CAUTION: Shorter objects that are detected (such as curbs or low barriers) can move into a blind spot.
CybertruckModel SModel X cannot alert you about an object while it is in a blind spot.
• Weather conditions (heavy rain, snow, or fog).
• The object is thin (such as a sign post).
• Park Assist’s operating range has been exceeded.
• The object is sound-absorbing or soft (such as powder snow).
• The object is sloped (such as a sloped embankment).
• CybertruckModel SModel X has been parked in, or being driven in, extremely hot or cold temperatures.
• The sensors are affected by other electrical equipment or devices that generate ultrasonic waves.
• You are driving in a location where the sensors' waves are deflected away from the vehicle (such as driving next to a wall or
pillar).
• The object is located too close to the bumper.
• A bumper is misaligned or damaged.
• An object that is mounted to CybertruckModel SModel X is interfering with and/or obstructing Park Assist (such as a bike
rack or bumper sticker).
• CybertruckModel SModel X rolls freely in the opposite direction you selected (for example, Park Assist does not display an
alert if CybertruckModel SModel X rolls backwards down a hill while in Drive).
Other Parking Aids
In addition to Park Assist, when shifted into Reverse, the backup camera displays a view of the area behind
CybertruckModel SModel X (see Rear Facing Camera(s) on page 306).

286

Owner's Manual

Owners Manual
Vehicle Hold
When CybertruckModel SModel X is stopped, Vehicle Hold can continue to apply the brakes even after you remove your foot
from the brake pedal.
Vehicle Hold will activate:
• Hold: Vehicle Hold is automatically enabled any time the vehicle comes to a complete stop.
• Creep or Roll: Vehicle Hold is enabled automatically anytime the vehicle is at a standstill and the brake is pressed to the
floor ( Roll is the default setting on your vehicle).
When the vehicle's stopping mode is set to Hold, Vehicle Hold is automatically enabled any time the vehicle comes to a
complete stop.
This indicator displays on the instrument paneltouchscreen whenever Vehicle Hold is actively braking
CybertruckModel SModel X.

To disengage Vehicle Hold, press the accelerator pedal or press and release the brake pedal.
NOTE: Shifting into Neutral also disengages Vehicle Hold.
NOTE: After actively braking CybertruckModel SModel X for approximately ten minutes, CybertruckModel SModel X shifts
into Park and Vehicle Hold cancels. CybertruckModel SModel X also shifts into Park if it detects that the driver has left the
vehicle.

Owner's Manual

287

Owners Manual
Vehicle Hold
When CybertruckModel SModel X is stopped, Vehicle Hold can continue to apply the brakes even after you remove your foot
from the brake pedal.
Vehicle Hold will activate:
• Hold: Vehicle Hold is automatically enabled any time the vehicle comes to a complete stop.
• Creep or Roll: Vehicle Hold is enabled automatically anytime the vehicle is at a standstill and the brake is pressed to the
floor ( Roll is the default setting on your vehicle).
When the vehicle's stopping mode is set to Hold, Vehicle Hold is automatically enabled any time the vehicle comes to a
complete stop.
This indicator displays on the instrument paneltouchscreen whenever Vehicle Hold is actively braking
CybertruckModel SModel X.

To disengage Vehicle Hold, press the accelerator pedal or press and release the brake pedal.
NOTE: Shifting into Neutral also disengages Vehicle Hold.
NOTE: After actively braking CybertruckModel SModel X for approximately ten minutes, CybertruckModel SModel X shifts
into Park and Vehicle Hold cancels. CybertruckModel SModel X also shifts into Park if it detects that the driver has left the
vehicle.

288

Owner's Manual

Owners Manual
Hill Start Assist
Hill Start Assist automatically engages the brakes for approximately one second when on a hill. This prevents
CybertruckModel SModel X from rolling during the time it takes for you to move your foot from the brake pedal to the
accelerator pedal. Hill Start Assist engages the brakes only if CybertruckModel SModel X is in Drive and facing uphill, or in
Reverse and facing downhill.
WARNING: After approximately one second, Hill Start Assist no longer brakes your vehicle and it could roll. Therefore,
quickly move your foot from the brake pedal to the accelerator pedal. Never rely on Hill Start Assist to prevent
CybertruckModel SModel X from rolling for more than one second. Failure to do so can result in a collision.

Owner's Manual

289

Owners Manual
Traction Control
How It Works
The traction control system constantly monitors the speed of the front and rear wheels. If CybertruckModel SModel X
experiences a loss of traction, the system minimizes wheel spin by controlling brake pressure and motor power. By default, the
traction control system is on. Under normal conditions, it should remain on to ensure maximum safety.
This yellow indicator flashes on the instrument panel whenever the traction control system is actively
controlling brake pressure and motor power to minimize wheel spin. If the indicator stays on, a fault is detected
with the traction control system. Contact Tesla Service.

WARNING: If the above indicator remains illuminated in situations in which you have not disabled the traction control
system (described next), the traction control system may not be operating correctly. Contact Tesla Service immediately.
WARNING: Traction control cannot prevent collisions caused by driving dangerously or turning too sharply at high
speeds.
Disabling Traction Control

Under normal conditions, the traction control system should remain enabled. Disable it only in circumstances where you
deliberately want the wheels to spin, such as:
• Starting on a loose surface, such as gravel or snow.
• Driving in deep snow, sand or mud.
• Rocking out of a hole or deep rut.
To allow the wheels to spin, touch Controls > Pedals & Steering > Slip Start.
The instrument panel displays an alert message when traction control is turned off.

Although the traction control system automatically reactivates the next time you start CybertruckModel SModel X, it is
strongly recommended that you enable it immediately after the circumstances that required you to disable it have passed.
NOTE: Traction Control can not be disabled when you are actively using cruise control.
Allowing Wheel Slip

To allow the wheels to spin at a limited speed, you can enable Slip Start. Slip Start can be enabled only when
CybertruckModel SModel X is moving 30 mph (48 km/h) or slower. Slip Start automatically disables when the speed exceeds
50 mph (80 km/h).
Under normal conditions, Slip Start should not be enabled. Enable it only in circumstances where you deliberately want the
wheels to spin, such as:
• Starting on a loose surface, such as gravel or snow.
• Driving in deep snow, sand or mud.
• Rocking out of a hole or deep rut.
To allow the wheels to spin, touch Controls > Pedals & Steering > Slip Start.

290

Owner's Manual

Owners Manual
The instrument panel displays an alert message when Slip Start is enabled.

Although Slip Start is automatically disabled the next time you start CybertruckModel SModel X, it is strongly recommended
that you disable it immediately after the circumstances that required you to enable it have passed.
NOTE: Slip Start can not be enabled when you are actively using cruise control.

Owner's Manual

291

Owners Manual
Acceleration Modes
The acceleration settings available on your CybertruckModel SModel X vary depending on date of manufacture and options
chosen at time of purchase:
• Chill: limits acceleration for a smooth and gentle ride (available on all vehicles equipped with Autopilot hardware).
• Standard: provides the normal level of acceleration (available on non-Performance All-Wheel Drive vehicles and Rear
Wheel Drive Model S vehicles equipped with Autopilot hardware).
• Sport: provides the normal level of acceleration (available on Performance All-Wheel Drive vehicles).
• Insane: increases peak torque by approximately 30 percent (available on Performance All-Wheel Drive vehicles not
equipped with the Ludicrous upgrade).
• Ludicrous: increases peak torque by approximately 60 percent (available on Performance All-Wheel Drive vehicles
equipped with the Ludicrous upgrade).
• Insane+: increases peak torque by approximately 30 percent (available on Performance All-Wheel Drive vehicles not
equipped with the Ludicrous upgrade) while also heating up the Battery to its ideal operating temperature to ensure access
to 100% of available power. Before choosing this setting, read about Using Insane+ or Ludicrous+ on page 292.
• Ludicrous+: increases peak torque by approximately 60 percent (available on Performance All-Wheel Drive vehicles
equipped with the Ludicrous upgrade) while also immediately heating up the Battery to its ideal operating temperature to
ensure access to 100% of available power. Before choosing this setting, read about Using Insane+ or Ludicrous+ on page
292.
NOTE: Although Chill does not directly improve driving range, using the increased torque and power available in Insane or
Ludicrous mode can reduce range and efficiency.
NOTE: When Chill is selected, Chill displays on the instrument panel above the driving speed.
In addition, a Performance All-Wheel Drive CybertruckModel SModel X also features Launch Mode to provide optimum
acceleration on surfaces with good traction. For the specific driving instructions required to use Launch Mode, see Launch
Mode on page 293.
To choose an acceleration mode, touch Controls > Pedals & Steering > Acceleration.
Using Insane+ or Ludicrous+
If you choose Insane or Ludicrous, additional power is available immediately. However, to achieve the absolute maximum
power (designed for short term use), you can choose Insane+ or Ludicrous+ to heat the Battery to its ideal operating
temperature. This ensure access to 100% of available power.
While the battery is being heated, the touchscreen displays a status message providing you with an approximate wait time,
and letting you know when the additional power is available. In addition to heating the Battery, Insane+ and Ludicrous+ modes
strive to keep the Battery within an optimal temperature range. Therefore, under aggressive driving scenarios, you may also
see the “Cooling” status for several minutes until temperatures fall. CybertruckModel SModel X stays in the chosen mode for
three hours, even if you leave the vehicle. After three hours, the feature times out.
NOTE: Insane+ and Ludicrous+ are designed to achieve maximum performance for short term acceleration. These settings are
not intended for daily driving. The tradeoff for the additional power boost is extra energy consumption and earlier power fade
on long drives. The Insane or Ludicrous acceleration settings provide a significant increase in performance even without
choosing the Insane+ or Ludicrous+ setting to achieve maximum Battery power. In fact, in normal driving situations, the
additional power that can be achieved using Insane+ and Ludicrous+ may be unnoticeable.
NOTE: To support Insane+ or Ludicrous+, the charge level must be 20% or higher. You cannot initiate these settings if the
charge level is less than 20%. In addition, these settings immediately cancel if at any time during use, the charge level drops
below 20%.
When using Insane+ or Ludicrous+, CybertruckModel SModel X consumes more energy to keep the Battery within an optimal
temperature range.
To cancel Insane+ or Ludicrous+ at any time, change the acceleration level to another setting. To prevent excess and
potentially unnecessary energy consumption (for example, you leave the vehicle and forget to cancel Insane+ or Ludicrous+),
these settings cancel automatically in three hours, regardless of whether you are still driving or have left the vehicle.

292

Owner's Manual

Owners Manual
NOTE: Insane+ or Ludicrous+ strives to keep the Battery within an optimal temperature range. In addition to heating the
Battery, these settings also cool the battery when necessary (for example, while driving at high speeds, during rapid
acceleration, driving for long periods, etc.).
Launch Mode
Launch Mode, available on Performance All-Wheel Drive vehicles only, provides optimum acceleration on surfaces with good
traction.
NOTE: Hard acceleration including, but not limited to, using launch mode, increases stress on the vehicle’s powertrain, and can
cause premature wear and aging of various components. CybertruckModel SModel X constantly monitors powertrain fatigue
and damage, and notifies you if vehicle components need to be serviced.
WARNING: Use Launch Mode only in appropriate locations where there is no cross traffic or pedestrians present. Launch
Mode is designed for use on closed circuit driving courses. It is the driver’s responsibility to ensure that driving style
and acceleration do not endanger or inconvenience other road users.
To Activate Launch Mode

1. Ensure the brakes are slightly warm by driving for a few minutes and using the brakes a few times.
2. Set the air suspension to Low (see Air Suspension on page 266Air Suspension on page 269Air Suspension on page 271).
3. Set the air suspension to Low or Very Low (see Air Suspension on page 266Air Suspension on page 269Air Suspension on
page 271).
4. Set the acceleration level to Insane+ or Ludicrous+ (if equipped).
NOTE: If equipped with the Ludicrous+ setting, you can achieve optimum performance by pressing and holding this setting
for three seconds.
5. With CybertruckModel SModel X shifted into Drive and at a complete stop with the steering wheel straight, firmly hold the
brake pedal with your left foot, then fully press the accelerator pedal. Within one second, the instrument panel displays a
message indicating that Launch Mode is enabled.
NOTE: Launch mode further lowers the front suspension, significantly reducing ground clearance.
6. Within twelve seconds of Launch Mode being enabled, release the brake pedal to launch the vehicle.
When you release the brake, CybertruckModel SModel X launches forward.
NOTE: Launch Mode is not available if Traction Control has been disabledSlip Start has been enabled (which allows the wheels
to spin). See Traction Control on page 290.
NOTE: Launch Mode is available only if the ambient temperature is 37° F (3° C) or warmer.

Owner's Manual

293

Owners Manual
Acceleration Modes
Touch Controls > Pedals & Steering > Acceleration to choose a preferred acceleration mode:
• Chill limits acceleration for a slightly smoother and gentler ride.
NOTE: When Chill is selected, Chill displays on the instrument panel, above the driving speed.
• Sport provides the normal level of acceleration.
• Insane (called Plaid on performance vehicles, if equipped) provides the maximum level of acceleration immediately
available.
NOTE: Using the increased torque and power available in Insane or Plaid mode can reduce range and efficiency.
NOTE: Insane or Plaid strives to keep the Battery within an optimal temperature range. In addition to heating the Battery,
these settings also cool the Battery when necessary (for example, while driving at high speeds, during rapid acceleration,
driving for long periods, etc.).
NOTE: You can improve the efficiency of the cabin heating by reducing your selected acceleration mode. This allows the heat
pump system to take more heat from the Battery to efficiently heat the cabin, instead of maintaining the Battery's ability to
provide peak acceleration performance. This helps to maximize driving efficiency in colder weather. Note that when
subsequently increasing the acceleration mode, the Battery requires time to warm up before the increased level of
acceleration is available.
In addition, CybertruckModel SModel X features Drag Strip Mode. Using Drag Strip Mode to precondition your
CybertruckModel SModel X is useful before a short distance race.
Drag Strip Mode
Drag Strip Mode preconditions the Battery and drive unit to ideal operating temperatures for timed acceleration.
CybertruckModel SModel X stays in Drag Strip Mode for three hours, even if you leave the vehicle. After three hours, the
feature times out to prevent unnecessary energy consumption (for example, you leave the vehicle and forget to cancel Drag
Strip Mode).
When using Drag Strip Mode, CybertruckModel SModel X consumes more energy to keep the Battery within an optimal
temperature range.
Cancel Drag Strip Mode at any time by toggling Drag Strip Mode off.
NOTE: Drag Strip Mode automatically disables Slip Start when enabled.
WARNING: Drag Strip Mode is designed for use on closed circuit driving courses only. It is the driver’s responsibility to
ensure that driving style and acceleration do not endanger or inconvenience other road users.
How to Launch the Vehicle

The touchscreen provides visual instructions on how to launch:
1. Touch Controls > Pedals & Steering > Drag Strip Mode.
2. Wait for the instrument panel to indicate that the vehicle is Peak Performance Ready.
3. With CybertruckModel SModel X shifted into Drive and at a complete stop, firmly hold the brake pedal with your left foot,
then fully press the accelerator pedal.
4. Once step 3 is complete, the front suspension begins lowering into a "cheetah stance".
NOTE: Suspension lowering for "cheetah stance" significantly reduces ground clearance.
5. Wait for the instrument panel to indicate that Drag Strip Mode is Ready to Launch.
6. Once you see "Cheetah Stance Enabled" and "Ready to launch" on the instrument panel, release the brake pedal to launch
the vehicle.

294

Owner's Manual

Owners Manual
Track Mode
Track Mode, available only on Plaid CybertruckModel SModel X vehicles, is designed to modify the stability control, traction
control, regenerative braking, and cooling systems to increase performance and handling while driving on closed circuit
courses. Track Mode improves cornering ability by intelligently using the motors, and regenerative and traditional braking
systems. When enabled, the cooling system runs at an increased level before, during, and after aggressive driving sessions to
allow your vehicle’s systems to withstand the surplus heat.
In Track Mode, adaptive suspension damping is optimized for handling and vehicle body control to promote driver confidence
in dynamic maneuvers. Ride height is automatically set to Low and the suspension no longer automatically raises for comfort
over rough surfaces.
WARNING: Track Mode is designed for use only by experienced drivers familiar with closed circuit driving courses. Do
not use on public roads. It is the driver’s responsibility to drive safely and be in control of the vehicle and all times to
ensure safety to self and others. Vehicle behavior (including traction and stability control) differs when using Track
Mode and driver must exercise caution at all times.
WARNING: For speeds above 158 mph (255 km/h), GVWR (Gross Vehicle Weight Rating) and GAWR (Gross Axle Weight
Ratings) must not exceed the maximums stated on the Vehicle Certification label (see Vehicle Loading on page 533).
Using Track Mode
Track Mode is always disabled when you start CybertruckModel SModel X. To enable Track Mode for your current drive, shift
into Park and follow these steps:
1. Touch Controls > Pedals & Steering > Track Mode.
When enabled, TRACK displays on the instrument panel above the driving speed, and a Track Mode pane appears on the
map. The Track Mode pane displays important at-a-glance status information about the Battery and the motors (see
Monitoring Vehicle Health on page 297) and a real-time accelerometer (see G-Meter on page 297).
2. If desired, customize the Track Mode settings by touching Customize on the Track Mode pane of the touchscreen (see
Customizing Track Mode on page 296). You can also customize the Track Mode settings by touching Pedals & Steering >
Driving, then touching Customize next to the Track Mode setting.
NOTE: For optimum performance, wait for the battery and motor temperatures to reduce if highlighted in yellow or red.
3. If desired, start the Lap Timer (see Using the Lap Timer on page 297).
4. Shift into gear and GO!
If you started the Lap Timer, each time you pass the start/finish location, the timer resets for the next lap. See Using the
Lap Timer on page 297.
When Track Mode is on:
◦ Autopilot features are unavailable.
◦ The Slip Start setting is overridden.
◦ Energy usage increases.
◦ Entertainment features are unavailable.
◦ Auto Shift (Beta) is disabled (see Auto Shift (Beta) on page 246 for more information).
◦ Settings for Adaptive Suspension Damping are disabled (Track Mode automatically optimizes adaptive damping to
support aggressive driving).
Use the touchscreen setting to turn Track Mode off at any time. Powering off CybertruckModel SModel X also turns off
Track Mode (although it may still appear on the touchscreen if Post-Drive cooling is in progress). When Track Mode is off,
all settings return to their previous state and all features return to their normal operating state.
NOTE: If CybertruckModel SModel X powers off while Track Mode is still enabled for Post-Drive cooling, the touchscreen
displays a popup that provides quick access to re-enabling it when you power CybertruckModel SModel X back on.

Owner's Manual

295

Owners Manual
CAUTION: Driver assistance features are automatically disabled when Track Mode is On. It is the driver’s responsibility
to drive safely and be in control of the vehicle at all times. Driver Assistance features automatically re-enable when
Track Mode is turned Off.
Top Speed, Tires, and Tire Pressures
A CybertruckModel SModel X equipped with Tesla Carbon Ceramic brakes is capable of achieving a top speed of 200 mph
(322 km/h).
WARNING: Never attempt to drive at 200 mph (322 km/h) unless CybertruckModel SModel X is equipped with the Tesla
Carbon Ceramic brake kit and the appropriate tires.
Customizing Track Mode
To customize Track Mode, touch Customize on the Track Mode pane that appears on the map when you enable Track Mode.
You can also access the Track Mode settings by touching Controls > Pedals & Steering, then touching Customize next to the
Track Mode setting. Choose an existing Track Mode setting from the list of pre-defined profiles provided by Tesla. Or create a