No data.

No data.

3. Hazards Identification
Emergency Overview

DANGER. Extremely Flammable. Contents under Pressure. Harmful or fatal if swallowed. Irritating to eyes,
skin and mucous membranes. Vapor may cause flash fire! May be harmful if inhaled or absorbed through the
skin! Overexposures may cause central nervous system (CNS) depression and/or other target organ effects!
Aspiration into the lungs can cause pulmonary edema and chemical pneumonia!
Route(s) of Entry:

Inhalation? Yes

Skin? Yes

Eyes? Yes

Ingestion? Yes

Potential Health Effects (Acute and Chronic)

Inhalation: Breathing high concentrations of vapor may cause respiratory irritation, euphoria, excitation or
giddiness, headache, nausea, vomiting, abdominal pain, loss of appetite, fatigue, muscular weakness, staggering
gait, and central nervous system (CNS) depression. CNS effects include dizziness, drowsiness, disorientation,
vertigo, memory loss, visual disturbances, difficulty with breathing, convulsions, unconsciousness, paralysis,
Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
White Lithium Grease

Page: 2
Printed: 10/28/2013
Revision: 10/25/2013
Supercedes Revision: 10/03/2007

coma, and even death, depending upon the level of exposure concentration and/or duration.
Eye Contact: Animal test results on similar materials suggest that this product can cause minimal to moderate eye
irritation upon short-term exposure.
Skin contact: Animal test results on similar materials suggest that this product can cause moderate skin irritation.
This material may also be absorbed through the skin and produce CNS depression effects (see "inhalation"
above). If the skin is damaged, absorption increases. Prolonged and/or repeated contact may cause moderate to
severe dermatitis.
Ingestion: If swallowed, this material may irritate the mucous membranes of the mouth, throat, and esophagus. It
can be readily absorbed by the stomach and intestinal tract. Due to it's light viscosity, there is a danger of
aspiration into the lungs during vomiting. Aspiration can result in severe lung damage or death. Progressive CNS
depression, respiratory insufficiency, and ventricular fibrillation may also result in death.
Signs and Symptoms Of Exposure

Inhalation: Irritation, discomfort, or signs of central nervous system depression (see health effects for listing).
Eye Contact: Stinging, watering, redness, and swelling.
Skin contact: Redness, itching, and burning of the skin. Chronic symptoms may include drying, swelling, scaling,
blistering, cracking, and severe tissue damage.
Ingestion: Irritation, burning sensation of the mouth and esophagus, nausea, vomiting, dizziness, staggering gait,
drowsiness, loss of consciousness, and delirium, as well as additional central nervous system (CNS) effects (see
"inhalation" above).
Medical Conditions Generally Aggravated By Exposure

Personnel with pre-existing central nervous system (CNS) disease, neurological conditions, skin disorders,
chronic respiratory diseases, or impaired liver or kidney function should avoid exposure.
OSHA Hazard Classes:

HEALTH HAZARDS : Irritant
PHYSICAL HAZARDS : Combustible Liquid, Compressed Gas, Flammable Gas
TARGET ORGANS & EFFECTS: Lungs, Kidney, Eyes, Skin, Blood, Liver, Central Nervous System, Mucous
Membranes, Respiratory System

4. First Aid Measures
Emergency and First Aid Procedures

Inhalation: Immediately move victim to fresh air. If victim is not breathing, immediately begin rescue breathing.
If heart has stopped, immediately begin cardiopulmonary resuscitation (CPR). If breathing is difficult, 100
percent humidified oxygen should be administered by a qualified individual. Seek medical attention immediately.
Eye Contact: Check for and remove contact lenses. If irritation or redness develops, flush eyes with cool, clean,
low-pressure water for at least 15 minutes. Hold eyelids apart to ensure complete irrigation of the eye and eyelid
tissue. Do not use eye ointment. Seek medical attention immediately.
Skin Contact: Remove contaminated shoes and clothing. Flush affected area with large amounts of water. If skin
surface is damaged, apply a clean dressing and seek medical attention. Do not use ointments. If skin surface is not
damaged, clean affected area thoroughly with mild soap and water. Seek medical attention if tissue appears
damaged or if pain or irritation persists.
Ingestion: Do not induce vomiting or give anything by mouth. If spontaneous vomiting is about to occur, place
victim's head below knees. If victim is drowsy or unconscious, place on the left side with head down. Never give
Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
White Lithium Grease

Page: 3
Printed: 10/28/2013
Revision: 10/25/2013
Supercedes Revision: 10/03/2007

anything by mouth to a person who is not fully conscious. Do not leave victim unattended. Seek medical attention
immediately.
Note to Physician

Inhalation overexposure can produce toxic effects. Monitor for respiratory distress. If cough or difficulty in
breathing develops, evaluate for upper respiratory tract inflammation, bronchitis, and pneumonitis. Vigorous
anti-inflammatory/steroid treatment may be required at first evidence of upper airway or pulmonary edema.
Administer 100 percent humidified supplemental oxygen with assisted ventilation, as required.
If ingested, this material presents a significant aspiration/chemical pneumonitis hazard. As a result, induction of
emesis is not recommended. Administer an aqueous slurry of activated charcoal followed by a cathartic such as
magnesium citrate or sorbitol. Also, treatment may involve careful gastric lavage if performed soon after
ingestion or in patients who are comatose or at risk of convulsing. Protect the airway by cuffed endotracheal
intubation or by placement of the body in a Trendelenburg and left lateral decubitus position. Obtain chest X-ray
and liver function tests. Monitor for cardiac function, respiratory distress and arterial blood gases in severe
exposure cases.

5. Fire Fighting Measures
Flash Pt:

< -150.00 F (-101.1 C)

Explosive Limits:

LEL: No data.

Autoignition Pt:

No data available.

Method Used: Estimate
UEL: No data.

Fire Fighting Instructions

As with all fires involving chemicals, responders should wear full bunker gear and a self contained breathing
apparatus. Use water spray to keep containers cool to prevent rupture of containers.
Flammable Properties and Hazards

Aerosols are a mixture of gases and liquids.
The gas component of this material is extremely flammable with a flashpoint of -156 F.
The liquid component of this material is a flammable liquid with a flashpoint of 96 F.
The liquid component will release vapors at or approaching its flash point temperature. When mixed with air in
certain proportions and exposed to an ignition source, this vapor can cause a flash fire. Vapors are heavier than
air and may travel long distances along the ground to an ignition source and flash back. May create vapor/air
explosion hazard in confined spaces such as sewers.
If container is not properly cooled, containers will rupture in the heat of a fire.
Hazardous Combustion Products

Burning or excessive heating may produce smoke, carbon dioxide, and possibly other harmful gases/vapors.
Extinguishing Media

SMALL FIRE: Use dry chemicals, carbon dioxide (CO2), foam, or inert gas (nitrogen).
LARGE FIRE: Use foam, water fog, or waterspray. Water fog and spray are effective in cooling and adjacent
structures. A water jet may be used to cool the vessel's external walls to prevent pressure build-up, autoignition,
or explosion. NEVER use a water jet directly on the fire because it may spread the fire to a larger area.
Unsuitable Extinguishing Media

No data available.

6. Accidental Release Measures
Steps To Be Taken In Case Material Is Released Or Spilled

Release causes an immediate fire or explosion hazard. Evacuate all non-essential personnel from immediate area
and establish a "regulated zone" with site control and security. Eliminate all ignition sources. Remove spillage
immediately from hard, smooth walking areas. Prevent its entry into waterways, sewers, basements, or confined
areas. Absorb or cover with dry earth, sand, or other non-combustible material and transfer to appropriate waste
containers. Use grounded and/or clean, non-sparking tools during clean-up operations.
Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
White Lithium Grease

Page: 4
Printed: 10/28/2013
Revision: 10/25/2013
Supercedes Revision: 10/03/2007

7. Handling and Storage
Precautions To Be Taken in Handling

Do not handle or store near heat, sparks, or any other potential ignition sources. Do not contact with oxidizable
materials. Do not breathe vapor. Use only with adequate ventilation/personal protection. Avoid contact with
eyes, skin, and clothing. Prevent contact with food, chewing, or smoking materials. Do not take internally.
Promptly remove contaminated clothing. Wash exposed skin thoroughly with soap and water after handling.
Precautions To Be Taken in Storing

Store and transport in accordance with all applicable laws. Keep containers tightly closed and store in a cool, dry,
well ventilated place, plainly labeled, and out of closed vehicles. Keep away from all ignition sources! Keep
away from children.

8. Exposure Controls/Personal Protection
Respiratory Equipment (Specify Type)

For unknown vapor concentrations use a positive-pressure, pressure-demand, self-contained breathing apparatus
(SCBA). For known vapor concentrations above the occupational exposure guidelines, use NIOSH-approved
organic vapor respirator if adequate protection is provided. Protection factors vary depending upon the type or
respirator used. Respirator use should follow OSHA requirements or equivalent standard.
Eye Protection

Safety glasses with side shields are recommended as a minimum protection.
Protective Gloves

Avoid skin contact and use gloves (disposable PVC, neoprene, nitrile, vinyl, or PVC/NBR).
Other Protective Clothing

If general contact occurs, IMMEDIATELY removed soaked clothing and take a shower. Contaminated leather
goods should be removed and discarded.
Engineering Controls (Ventilation etc.)

Provide exhaust ventilation or other engineering controls to keep the airborne concentrations of vapor and/or
mists below the pertinent exposure limits. All electrical equipment should comply with appropriate standards.
Work/Hygienic/Maintenance Practices

Before eating, drinking, smoking, use of toilet facilities, or leaving work, wash hands with plenty of mild soap
and water. DO NOT use gasoline, kerosine, or other solvents, or harsh abrasive skin cleaners.
Ensure that an emergency eye wash station and safety shower are near the work-station location.

9. Physical and Chemical Properties
Physical States:

[ X ] Gas

Melting Point:

No data.

Boiling Point:

No data.

Autoignition Pt:

No data.

Flash Pt:

< -150.00 F (-101.1 C)

Specific Gravity (Water = 1):

0.82 - 0.84

Vapor Pressure (vs. Air or mm Hg):

No data.

Vapor Density (vs. Air = 1):

No data.

Evaporation Rate:

No data.

Solubility in Water:

No data.

[ X ] Liquid

[ ] Solid

Method Used: Estimate

at 25.0 C (77.0 F)

Solubility Notes

Insoluble in water

Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
White Lithium Grease
Percent Volatile:

No data.

VOC / Volume:

48.0000 WT%

Viscosity:

2700 CPS

Page: 5
Printed: 10/28/2013
Revision: 10/25/2013
Supercedes Revision: 10/03/2007

at 20.0 C (68.0 F)

Appearance and Odor

Liquid component is an off-white liquid with solvent/hydrocarbon odor.
Gaseous component has a strong hydrocarbon odor.
With the exception of VOC percentage and appearance and odor, all data in Section 9 pertains to the liquid
component only.

10. Stability and Reactivity
Stability:

Unstable [

]

Stable [ X ]

Conditions To Avoid - Instability

Keep away from extreme heat, strong acids, and strong oxidizing conditions.
Incompatibility - Materials To Avoid

Strong acids, alkalies, and oxidizers such as liquid chlorine, hydrogen peroxide, and oxygen.
Hazardous Decomposition Or Byproducts

No substances are readily identified from composition; but no degradation data is available.
Hazardous Polymerization:

Will occur [

]

Will not occur [ X ]

Conditions To Avoid - Hazardous Polymerization

None known.

11. Toxicological Information
Toxicological Information

No data available.
Chronic Toxicological Effects

No data available.
Carcinogenicity/Other Information

This product does not contain any components at concentrations above 0.1% which are considered carcinogenic
by OSHA, IARC, or NTP.
Reports have associated repeated and prolonged occupational overexposure to solvents with irreversible brain
and nervous system damage (sometimes referred to as "Solvent or Painter's Syndrome"). Intentional misuse by
deliberately concentrating and inhaling this product may be harmful or fatal.
Carcinogenicity:

NTP? No

IARC Monographs? No

OSHA Regulated? No

12. Ecological Information
General Ecological Information

No data available.

13. Disposal Considerations
Waste Disposal Method

As produced this material meets the RCRA definition for "ignitable". Dispose of in accordance with all Federal,
State, Provincial, and local laws and regulations.
RCRA Waste ID Code:

Licensed to Excelda Manufacturing, Inc.

D001

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
White Lithium Grease

Page: 6
Printed: 10/28/2013
Revision: 10/25/2013
Supercedes Revision: 10/03/2007

14. Transport Information
LAND TRANSPORT (US DOT)
DOT Proper Shipping Name

Aerosols, flammable

DOT Hazard Class:

2.1

DOT Hazard Label:

FLAMMABLE GAS

UN/NA Number:

UN1950

Additional Transport Information

This material may be reclassified according to 49 CFR 173.306.

15. Regulatory Information
US EPA SARA Title III
Chemical Name

CAS #

Sec.304 RQ

Sec.313 (TRI)

Sec.110

1.

Hydrotreated light distillate (petroleum)

64742-47-8 No

Sec.302 (EHS)

No

No

No

2.

Solvent naphtha medium aliphatic

64742-88-7 No

No

No

No

3.

Propane

74-98-6 No

No

No

No

4.

Isobutane (2-Methylpropane)

75-28-5 No

No

No

No

5.

Mineral oil

64742-65-0 No

No

No

No

6.

Mineral oil, petroleum distillates, hydrotreated
heavy naphthenic

64742-52-5 No

No

No

No

7.

Lithium 12-hydroxystearate

7620-77-1 No

No

No

No

US EPA CAA, CWA, TSCA
Chemical Name

CAS #

EPA CWA NPDES

EPA TSCA

CA PROP 65

1.

Hydrotreated light distillate (petroleum)

64742-47-8 No

EPA CAA

No

Inventory

No

2.

Solvent naphtha medium aliphatic

64742-88-7 No

No

Inventory

No

3.

Propane

74-98-6 No

No

Inventory

No

4.

Isobutane (2-Methylpropane)

75-28-5 No

No

Inventory

No

5.

Mineral oil

64742-65-0 No

No

Inventory

No

6.

Mineral oil, petroleum distillates, hydrotreated
heavy naphthenic

64742-52-5 No

No

Inventory

No

7.

Lithium 12-hydroxystearate

7620-77-1 No

No

Inventory