4.

Sodium tolutriazole

64665-57-2 No

No

Inventory, 4 Test

No

SARA (Superfund Amendments and
Reauthorization Act of 1986) Lists:
Sec.302:

EPA SARA Title III Section 302 Extremely Hazardous Chemical with TPQ. * indicates 10000
LB TPQ if not volatile.

Sec.304:

EPA SARA Title III Section 304: CERCLA Reportable + Sec.302 with Reportable Quantity. **
indicates statutory RQ.

Sec.313:

EPA SARA Title III Section 313 Toxic Release Inventory. Note: -Cat indicates a member of a
chemical category.

Sec.110:

EPA SARA 110 Superfund Site Priority Contaminant List

TSCA (Toxic Substances Control
Act) Lists:
Inventory:

Chemical Listed in the TSCA Inventory.

5A(2):

Chemical Subject to Significant New Rules (SNURS)

6A:

Commercial Chemical Control Rules

8A:

Toxic Substances Subject To Information Rules on Production

8A CAIR:

Comprehensive Assessment Information Rules - (CAIR)

8A PAIR:

Preliminary Assessment Information Rules - (PAIR)

8C:

Records of Allegations of Significant Adverse Reactions

8D:

Health and Safety Data Reporting Rules

8D TERM:

Health and Safety Data Reporting Rule Terminations

12(b):

Notice of Export

Other Important Lists:
CWA NPDES:

EPA Clean Water Act NPDES Permit Chemical

CAA HAP:

EPA Clean Air Act Hazardous Air Pollutant

CAA ODC:

EPA Clean Air Act Ozone Depleting Chemical (1=CFC, 2=HCFC)

CA PROP 65:

California Proposition 65

International Regulatory Lists:
EPA Hazard Categories:

This material meets the EPA 'Hazard Categories' defined for SARA Title III Sections 311/312 as indicated:
[X] Yes [ ] No Acute (immediate) Health Hazard
[X] Yes [ ] No Chronic (delayed) Health Hazard
[X] Yes [ ] No Fire Hazard
[ ] Yes [X] No Sudden Release of Pressure Hazard
[ ] Yes [X] No Reactive Hazard
Regulatory Information

TSCA: All ingredients in this product are listed on the TSCA Inventory or are otherwise exempt.
CA Prop 65: This product is known to contain chemicals known to the State of California to cause cancer, birth
Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
Diesel Cooling System Additive

Page: 7
Printed: 10/28/2013
Revision: 10/21/2013

defects or other reproductive harm.
Regulatory Information Statement

The information contained herein is based on data considered accurate. However, no warranty is expressed or
implied regarding the accuracy of this data or the results to be obtained from the use thereof. Vendor assumes no
responsibility for injury to vendee or third person proximately caused by the material if reasonable safety
procedures are not adhered to as stipulated in the data sheet. Additionally, vendor assumes no responsibility for
injury to vendee or third persons proximately caused by abnormal use of the material even if reasonable safety
procedures are followed. Furthermore, vendee assumes all risk in use of the material.

16. Other Information
Company Policy or Disclaimer

THIS INFORMATION IS FURNISHED WITHOUT WARRANTY, EXPRESSED OR IMPLIED, EXCEPT
THAT IS ACCURATE TO THE BEST KNOWLEDGE OF HINO MOTOR SALES USA. THE DATA ON
THIS SHEET RELATES ONLY TO THE SPECIFIC MATERIAL DESIGNATED HEREIN. HINO MOTOR
SALES USA. ASSUMES NO LEGAL RESPONSIBILITY FOR USE OR RELIANCE UPON THIS DATA.

Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

Page: 1

MATERIAL SAFETY DATA SHEET
Diesel Fuel Lubricity Additive
Flammability

Health

1

2

Instability

Printed:
Revision:
Supercedes Revision:
Date Created:

0
Special Hazard

10/28/2013
07/11/2011
12/12/2007
05/14/1998

1. Product and Company Identification
Product Code:

730-1449

Product Name:

Diesel Fuel Lubricity Additive

Manufacturer/Supplier/Distributor Information
Company Name:

Hino Motor Sales USA, Inc.
41180 Bridge St.
Novi, MI 48375

Phone Number:

(248)699-9300

Fax Number:

(248)699-9310

Part Number:

HN001234021

Revision Date:

07/11/2011

2. Composition/Information on Ingredients
Chemical Name

CAS #

1.

Kerosine

8008-20-6 90.0 -95.0 %

Concentration

2.

Proprietary additives

3.

Naphthalene

NA

5.0 -10.0 %

91-20-3 0.01 -0.095 %

OSHA PEL

ACGIH TWA

Other Limits

NO DATA

NO DATA

14ppm

NO DATA

NO DATA

NO DATA

10 ppm

10 ppm

No data.

Chemical Name

RTECS #

OSHA STEL

OSHA CEIL

ACGIH STEL

ACGIH CEIL

1.

Kerosine

OA5500000

No data.

No data.

No data.

No data.

2.

Proprietary additives

NA

No data.

No data.

No data.

No data.

3.

Naphthalene

QJ0525000

No data.

No data.

15 ppm

No data.

3. Hazards Identification
Emergency Overview

DANGER: Combustible liquid and vapor. Harmful or fatal if swallowed. Aspiration hazard. May cause severe
skin irritation after prolonged or repeated contact. A component may cause allergic skin reaction. Causes eye
irritation.
Route(s) of Entry:

Inhalation? Yes

Skin? Yes

Eyes? Yes

Ingestion? Yes

Potential Health Effects (Acute and Chronic)

EYE: Eye irritant. Contact may cause stinging, watering, redness, and swelling.
SKIN: Skin irritant. Contact may cause redness and burning of the skin. Prolonged or repeated contact may
cause drying and cracking of the skin and severe skin damage. No harmful effects from skin absorption have
been reported.
INHALATION: No information available. Studies by other exposure routes suggest a low degree of toxicity.
INGESTION: A component of this material is toxic. May be harmful if swallowed. Aspiration Hazard- This
material can enter lungs during swallowing or vomiting and cause lung inflammation and damage.
Signs and Symptoms Of Exposure

Effects of overexposure may include irritation of the nose and throat, irritation of the digestive tract, headaches,
nausea, vomiting, diarrhea, signs of nervous system depression , abdominal pain, an allergic skin reaction through
repeated contact, pneumonoconiosis, blood disorders, and jaundice.

Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
Diesel Fuel Lubricity Additive

Page: 2
Printed: 10/28/2013
Revision: 07/11/2011
Supercedes Revision: 12/12/2007

Medical Conditions Generally Aggravated By Exposure

Skin disorders, blood disorders and liver disorders.
OSHA Hazard Classes:

HEALTH HAZARDS : Toxic, Irritant
PHYSICAL HAZARDS : Combustible Liquid
TARGET ORGANS & EFFECTS: Kidney, Eyes, Skin, Liver, Respiratory System, Blood

4. First Aid Measures
Emergency and First Aid Procedures

EYES: Move victim away from exposure and into fresh air. If irritation or redness develops, flush eyes with
clean water and seek medical attention. For direct contact, hold eyelids apart and flush the affected eye(s) with
clean water for at least 15 minutes. Seek medical attention.
SKIN: Remove contaminated shoes and clothing, and flush affected area(s) with large amounts of water. If skin
surface is damaged, apply a clean dressing and seek medical attention. If skin surface is not damaged, cleanse
affected area thoroughly by washing with mild soap and water. If irritation or redness develops, seek medical
attention.
INHALATION: If respiratory symptoms develop, move victim away from source of exposure and into fresh air.
If symptoms persist, seek medical attention. If victim is not breathing immediately begin artificial respiration. If
breathing difficulties develop, oxygen should be administered by qualified personnel. Seek immediate medical
attention.
INGESTION: Aspiration hazard: Do not induce vomiting or give anything by mouth because this material can
enter the lungs and cause severe lung damage. If victim is drowsy or unconscious, place on the left side with the
head down. If possible, do not leave victim unattended. Seek medical attention.
NOTE: IF AN ALLERGIC REACTION TO THIS MATERIAL DEVELOPS, AVOID ANY FURTHER
CONTACT.

5. Fire Fighting Measures
Flash Pt:

52.20 C (126.0 F)

Explosive Limits:

LEL: No data.

Autoignition Pt:

No data available.

Method Used: Pensky-Marten Closed Cup
UEL: No data.

Fire Fighting Instructions

Emergency responders in the danger area should wear bunker gear and self-contained breathing apparatus for
fires beyond the incipient stage. In addition, wear other appropriate protective equipment as conditions warrant.
Isolate damage area, keep unauthorized personnel out. Stop spill/release if it can be done with minimal risk.
Move undamaged containers from danger area if it can be done with minimal risk. Water spray may be useful in
minimizing or dispersing vapors. Cool equipment exposed to fire with water, if it can be done with minimal risk.
Avoid spreading burning liquid with water used for cooling purposes.
Flammable Properties and Hazards

Vapors flammable. Material may pool on water and become floating fire hazards.
Hazardous Combustion Products

Oxides of carbon, primarily carbon dioxide and carbon monoxide.
Extinguishing Media

Foam, CO2, dry chemical or halon is recommended. Use water spray to cool fire exposed surfaces and to protect
personnel. Water may be ineffective for extinguishment, unless under favorable conditions by experienced fire
fighters. Halon may decompose into toxic material. Carbon dioxide can displace oxygen. Use caution when
applying halon or carbon dioxide in confined spaces.
Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
Diesel Fuel Lubricity Additive

Page: 3
Printed: 10/28/2013
Revision: 07/11/2011
Supercedes Revision: 12/12/2007

Unsuitable Extinguishing Media

No data available.

6. Accidental Release Measures
Steps To Be Taken In Case Material Is Released Or Spilled

Keep all sources of ignition and hot metal surfaces away from spill/release, use explosion proof equipment. Stay
upwind and away from spill/release. Isolate danger area and keep unauthorized personnel out. Stop spill/release
if it can be done with minimal risk. Wear appropriate protective equipment including respiratory protection as
conditions warrant. Prevent spilled material form entering sewers, storm drains, other unauthorized treatment
drainage systems, and natural waterways. Dike far ahead of spill for later recovery or disposal. Use foam on
spills to minimize vapors. Spilled material may be absorbed into an appropriate absorbent material. Notify fire
authorities and appropriate federal, state, and local agencies. Immediate cleanup of any spill is recommended. If
spill of any amount is made into or upon navigable waters, the contiguous zone, or adjoining shorelines, notify
the National Response Center (800-424-8802).

7. Handling and Storage
Precautions To Be Taken in Handling

Open container slowly to relieve any pressure. Bond and ground all equipment when transferring from one
vessel to another. Can accumulate static charge by flow or agitation. Vapor can be ignited by static discharge.
The use of explosion-proof equipment is recommended and may be required. Do not enter confined spaces such
as tanks or pits without following proper entry procedures such as ASTMD-4276 and 29CFR 1910.146. The use
of respiratory protection is advised when concentrations exceed any established exposure limits. Wash
thoroughly after handling. Do not wear contaminated clothing or shoes. Use good personal hygiene practice.
Empty containers retain residue (liquid and/or vapor) and may be dangerous. Do not pressurize, cut, weld,
braze, solder, drill, grind, or expose such containers to heat, flame, sparks, or other sources of ignition. They may
explode and cause injury or death. Empty drums should be completely drained properly bunged, and promptly
shipped to the supplier or a drum recondition. All containers should be disposed of in an environmentally safe
manner and in accordance with governmental regulations. Before working on or in tanks which contain or have
contained this material, refer to Occupational Safety and Health Administration Regulations, ANSI Z49.1 and
other governmental and industrial references pertaining to cleaning, repairing, welding, or other contemplated
operations.
Precautions To Be Taken in Storing

STORAGE: Keep containers tightly closed. Use and store this material in cool, dry, well-ventilated areas away
from heat, direct sunlight, hot metal surfaces, and all sources of ignition. Post area "No Smoking or Open Flame.
" Store only in approved containers. Keep away from any incompatible material. Protect container against
physical damage. Outdoor or detached storage is preferred. Indoor storage should meet OSHA standards and
appropriate fire codes.

8. Exposure Controls/Personal Protection
Respiratory Equipment (Specify Type)

The use of respiratory protection is advised when concentrations are expected to exceed the established exposure
limits. Depending on the airborne concentration, use a respirator with appropriate cartridges or supplied-air
equipment.
Eye Protection

Approved eye protection to safeguard against potential eye contact, irritation, or injury is recommended.
Protective Gloves

Impervious gloves .
Other Protective Clothing

Eye wash and quick drench shower facilities should be available in the work area. Thoroughly clean shoes and
wash contaminated clothing before reuse. It is recommended that impervious clothing be worn.
Licensed to Excelda Manufacturing, Inc.

ANSI Z400.1 format

MATERIAL SAFETY DATA SHEET
Diesel Fuel Lubricity Additive

Page: 4
Printed: 10/28/2013
Revision: 07/11/2011
Supercedes Revision: 12/12/2007

Engineering Controls (Ventilation etc.)

If current ventilation practices are not adequate to maintain airborne concentrations below the established
exposure limits, additional ventilation or exhaust systems may be required. Where explosive mixtures may be
present, electrical systems safe for such locations must be used.
Work/Hygienic/Maintenance Practices

No data available.

9. Physical and Chemical Properties
Physical States:

[ ] Gas

Melting Point:

No data.

Boiling Point:

No data.

Autoignition Pt:

No data.

Flash Pt:

52.20 C (126.0 F)

Specific Gravity (Water = 1):

0.80 - 0.82

Vapor Pressure (vs. Air or mm Hg):

No data.

Vapor Density (vs. Air = 1):

No data.

Evaporation Rate:

No data.

Solubility in Water:

No data.

Percent Volatile:

> 90.0 % by weight.

Viscosity:

8 - 10.5 CST

[ X ] Liquid

[ ] Solid

Method Used: Pensky-Marten Closed Cup

at 25.0 C (77.0 F)

at 40.0 C (104.0 F)

Appearance and Odor

Amber colored, clear liquid; characteristic petroleum odor.

10. Stability and Reactivity
Stability:

Unstable [

]

Stable [ X ]

Conditions To Avoid - Instability

Stable under normal conditions of storage and handling. Flammable liquid and vapor. Vapor can cause flash fire.
Incompatibility - Materials To Avoid

Avoid contact with strong oxidizing agents.
Hazardous Decomposition Or Byproducts

Combustion can yield major amounts of oxides of carbon and minor amounts of oxides of sulfur and nitrogen.
Hazardous Polymerization:

Will occur [

]

Will not occur [ X ]

Conditions To Avoid - Hazardous Polymerization

None known.

11. Toxicological Information
Toxicological Information