cable to the diagnostic head and then
reattach to the vehicle.

•

Upon ODIS startup, select “Diagnosis” .

•

Select “Self Test” .

•

Select “Software Version Management”, then select
“SVM Code input” .

•

Select “Attach to the test plan” .

NOTE
RISK of Scan Tool Damage!
Do not leave the scan tool on the windshield during the
flash process, as it is possible that the windshield wipers
may cycle.

14

•

From the Test plan screen, Select “SVM Code input”
test plan , then select “Perform test”
.

•

Follow the on-screen prompts.

NOTE
Using Bluetooth for this action is PROHIBITED!
Damage caused to electronic components (e.g. ECM,
TCM, etc.) during the SVM flash process is not covered.
•

Enter SVM code
select “Accept”.

•

Follow the on-screen prompts.

“23T4A480” , then

TIP
KESSY Vehicles!
•

Due to a weak key battery, it may be necessary
to hold the key up to the reader coil during the
ignition on/off process of the flash.

•

Key(s) should always be left in the vehicle
during the flash process.

NOTE
After flashing, the vehicle will not start due to adaptation
values for reducing agent missing. Perform test plan to
reset reducing agent adaptation values prior to
attempting to start vehicle.
•

Perform “Reset reducing agent system adaptation
values” .

15

•

At the end of the diagnostic session, Select “Send”
and follow the prompt for sending the log
on-line.
NOTE
RISK of Non-payment!

Diagnosis logs must be sent on-line after the flash
process to be considered for reimbursement.

TIP
Technicians may find it helpful to also store the log
on a USB stick for back-up.

TIP
When exiting GFF, it is important to select “No”
.
•

Disconnect the VAS tester.

•

Switch off and disconnect the battery charger.

•

Reinstall the battery cover.

•

Release the parking brake.

Proceed to Section E

16

Section E – Supplemental Vehicle Emissions Control Information Label
Install Supplemental Vehicle Emissions Control
Information Label
TIP
•

The surface where the label is to be installed
must be clean, dry, and free from oil residue
prior to installing the label.

•

Label must NOT cover any existing label(s).

•

Label must be installed in location shown.

•

Photo documentation of label installed is
required.

•

Open the hood.

•

Clean the surface where the label is to be
installed .

•

Install the Supplemental Vehicle Emissions
Control Information Label, 03L 010 005 J, in the
location shown.

NOTE
DO NOT Cover existing VECI label!
New Vehicle Emissions Control Information (VECI) label
MUST NOT be placed over original VECI label.
Proceed to Section F

Section F – TDI Emissions Modification – Proof of Partial Completion Label
Install TDI Emissions Modification – Proof of Partial
Completion Label
TIP
•

The surface where the label is to be installed
must be clean, dry, and free from oil residue
prior to installing the label.

•

Label must NOT cover any existing label(s).

•

Photo documentation of label installed is
required.

•

When affixing the label, keep in mind that in the
future, a Phase 2 completion label will also need
to be affixed at a later date alongside this Phase
1 completion label.

17

•

Clean the surface next to the Vehicle Emission
Control Information Label where the TDI
Emissions Modification – Proof of Partial
Completion Label is to be installed.

•

Fill out and affix TDI Emissions Modification –Proof
of Partial Completion Label, part number CAMP
TDI 2016_3A.
NOTE

Place the label next to the Vehicle Emission Control
Information Label.
•

Apply clear overlay (provided).

•

Close the hood.

Proceed to Section G (California only)
Proceed to Section H (All States without California)

Section G – California Only Requirements
CALIFORNIA ONLY Requirements for Emissions
Campaigns Having Customer Notification
The California Air Resources Board and the Department
of Motor Vehicles (DMV) require emissions-related
campaigns to be completed prior to vehicle registration
renewal. When campaign work is done you must
provide the owner with a signed “Vehicle Emission
Recall – Proof of Correction” certificate (RC
EMIS_CAL VW). Certificates can be ordered at no cost
online via the Compliance Label Ordering portal at
www.accessaudi.com.
TIP
Ensure owners are aware of the importance of
retaining the completed certificate for their records. It
should be mailed to the California DMV only upon
request.
Proceed to Section H

18

Section H – Service Modification Documentation Requirements
Job Roles Summary:
•

Service Consultant – Initiates validation tool.

•

Service Technician –
modification requirements.

•

Manager – Validates the modification was properly
completed.

•

Dealer Representative/Cashier – Prints receipt,
fuel economy label and delivers to customer.

•

Warranty Administrator – Enters claim into the
SAGA system.

Completes

service

TIP
To access the interactive forms go to the TDI Settlement
Program microsite on vwhub.com. Then Select the “TDI
IN-FORM” Button from the lower left side of the microsite
navigation.
•

Enter the “TDI IN-FORM” tool .

•

Enter the VIN for the vehicle that requires
documentation.
TIP

The VIN can be manually typed in or using an iPad or
iPhone running i0S 9+, the camera can be used to scan
the VIN Barcode.
Please note ambient lighting, camera quality, etc. may
impact the effectiveness of the VIN scanning feature.

19

TIP
After the VIN has been entered, the system will
automatically validate that it is a TDI VIN. This will be
indicated by a green check mark that will appear next to
the VIN.

•

Validate the VIN is correct for the vehicle, then click
the “Submit” button .

•

Select “Service Modification Documentation Form”
.

•

Follow the on-screen prompts completely.

NOTE
RISK of Non-payment!
Not using the IN-FORM tool to document and validate
the modification will stop the processing of payment for
your dealership even if the modification has been
completed.

TIP
Upon completion of the Service Modification
Documentation Form, the Manager must validate the
repair in the IN-FORM tool.

Proceed to Section I

20

NOTE
Vehicle Sales REQUIREMENTS!
Additional REQUIRED steps are necessary for NEW
vehicles.

•

For NEW vehicles, obtain VIN-specific and other
necessary items according to Appendix A.
Complete Appendix A in addition to this repair.

•

Once the campaign has been completed, the
technician should stamp the repair order.

•

Stamps are available for ordering through the
Compliance Label Ordering Portal (item#
AUD4927ENG).

Section I – Campaign Stamp

Item#: AUD4927ENG

ALL WORK IS COMPLETE for Repair, continue to
Appendix A if vehicle is within New vehicle
inventory.

Appendix A – Requirements for Vehicles within “New” Vehicle Inventory
NOTE
Vehicle Sales REQUIREMENTS!
Additional REQUIRED steps are necessary for NEW
vehicles prior to sale.

21

•

Open glove box and insert the 2015 2.0L TDI
(Generation 3) booklet .

•

Open glove box and insert “Additional Disclosures
Regarding This Vehicle” information .

•

Open glove box and insert “Copy of Original
Emissions Recall Notice” information .

22

•

Remove original Monroney Label and discard.

•

Install new Monroney Label
in same location as original.

TIP
Monroney Labels are VIN-specific. Obtain new label as
required from Sales department or General Manager.

•

Install new Fuel Economy Label next to the Monroney Label.

TIP
Fuel Economy Labels are VIN-specific. Obtain new label
as required from Sales department or General Manager.

•

Place the sticker on the front driverside window on the lower rearward interior portion
of the window.

TIP
Window Stickers can be obtained from the Sales
department or General Manager.

23

Sales Preparation Process Roadmap

24

AUDI AG

I/VS

New 2015 2.0L TDI Vehicles – Sales Preparation
“Sales Preparation” program for new MY15 TDI 2.0L units in dealer inventory – Process Roadmap

Step 1: Perform
approved
Emissions
modification
(23T4)

Step 2: Complete
self authorized
repairs (as
detailed in
recall)

Step 3: Clear all
other open
recalls and
service actions

Step 4: Test drive
vehicle and seek
authorization for
other applicable
repairs

Step 5: Ensure
all materials
have been
included in the
vehicle
(Replacement
Monroney Label,
EPA Label,
Original
Emissions Recall
Notice, etc.)

Step 6: Review
vehicle with AoA
Technical Field
Manager for
sales readiness

Step 7: Consult
support
programs for
retail sale
(Owner Loyalty,
DEPP, AFS APR,
A3 TDI Support
Program)

25

Required Compliance Materials

26

AUDI AG

I/VS

New 2015 2.0L TDI Vehicles – Sales Preparation
PRIOR to sale - Materials that must be added to EVERY new MY15 TDI 2.0L unit in dealer inventory

1. Replacement Monroney Label
2. EPA Label – Emission Modification Supplement Label
3. Original Emissions Recall Notice (Copy)
4. AEM Disclosure Booklet
5. AEM Disclosure Letter
6. TDI Web Site Window Sticker

A package containing both VIN-specific and
non-VIN-specific materials will be sent to
every Service Manager.

27

AUDI AG

I/VS

New 2015 2.0L TDI Vehicles – Sales Preparation
Package that will be arriving for Service Managers

A package like this will
be sent to every Service
Manager.

28

•

•







29







30

Impor tant Information About Your

2015 2.0L TDI Audi
GENERATION 3 ENGINE

10011_audi.indd 1

31

1/3/17
AM
1/3/17 11:42
2:53 PM

Contents
About this Booklet .................................................... 1
Overview .................................................................. 2
Software and Hardware Updates ................................. 3
Changes in Maintenance Schedule ............................... 7
Emission Limits ......................................................... 7