“This site contains affiliate links for which OEMDTC may be compensated” |
May 16, 2022 NHTSA CAMPAIGN NUMBER: 22V340000
Rotary Shifter May Unintentionally Shift to Drive
Unintentionally shifting to drive can cause unexpected vehicle movement, increasing the risk of a crash.
NHTSA Campaign Number: 22V340
Manufacturer Daimler Trucks North America, LLC
Components POWER TRAIN
Potential Number of Units Affected 19
Summary
Daimler Trucks North America, LLC (DTNA) is recalling certain 2021-2022 FCCC MT50e walk-in vans. The rotary shift position knob may malfunction, which can cause an unintended shift to drive.
Remedy
All vehicles have been remedied, therefore no owner notification letters are necessary. Owners may contact DTNA customer service at 1-800-547-0712. DTNA’s number for this recall is FL934.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
NHTSA NS No. 22V-340
Manufacturer number: FL-934
There will be no publications for safety recall 22V-340.
All vehicles within this recall campaign have been repaired prior to the publication of a Dealer’s Bulletin or Owner Notification. All impacted serial numbers were inspected/repaired on 6/7/2022.
Chronology :
On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. On June 3, 2022, we became aware of additional units that had shipped prior to the recall determination and amended the population accordingly. On June 27, 2022, we amended the start dates to match the population update from June 3, 2020, no impact to vehicle population. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world.
2 Affected Products
Vehicle
MAKE | MODEL | YEAR |
FCCC | MT50E | 2021-2022 |
15 Associated Documents
Recall Acknowledgement
RCAK-22V340-8214.pdf 645.546KB
Defect Notice 573 Report
RCLRPT-22V340-1078.PDF 213.905KB
Defect Information Report
RMISC-22V340-8579.pdf 850.326KB
Recall 573 Report – May 25, 2022
RCLRPT-22V340-1786.PDF 214.018KB
Amended Defect Information Report
RMISC-22V340-0339.pdf 857.978KB
Recall 573 Report – June 3, 2022
RCLRPT-22V340-8045.PDF 214.095KB
Amended Defect Information Report
RMISC-22V340-3972.pdf 901.595KB
Recall 573 Report – June 4, 2022
RCLRPT-22V340-7842.PDF 214.094KB
Recall 573 Report – June 27, 2022
RCLRPT-22V340-3075.PDF 214.146KB
Defect Information Report
RMISC-22V340-2387.pdf 905.77KB
Owner Notification Letter(Part 577)
RCONL-22V340-6900.pdf 287.121KB
Recall Quarterly Report #1, 2022-2
RCLQRT-22V340-0202.PDF 211.148KB
Recall Quarterly Report #2, 2022-3
RCLQRT-22V340-4519.PDF 211.238KB
Manufacturer Notices(to Dealers,etc)
RCMN-22V340-6977.pdf 287.121KB
Recall Quarterly Report #3, 2022-4
RCLQRT-22V340-2044.PDF 211.327KB
Recalls Documents
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V340&docType=RCL
- 🍇➤Please Note: 1. The HD OBD option is available for heavy truck owners and the OBD/EOBD option is available for other vehicle. 2. Owners need to fix the problem with the truck first before they need clear the error code.
- 🍉➤【Support Full Systems for Heavy Duty Truck】 NL102 PLUS supports read and clear DTC, live data, ECU information for truck all systems. Including Engine, Transmission, Drivetrain, Suspension, ABS, ESP, Cluster, E-xhaust, P-articular, Suspension, Braking System, Cab Climate, Body Control, Instrument Panel, Fuel System and more, which are in compliance with J1939, J1708 and J1587 protocols, It includes almost American HD trucks(Class4-Class8), it is recommended that customers confirm before purchase that if they comply with the years and agreements supported by NL102P before purchasing.
- 🍋➤【Professional DPF Regeneration Tool】Force DPF Regen work on Cummings, Detroit, Maxxforce, ISUZU, HINO engine,It covers almost all US trucks, supported advanced features: DPF Regeneration,D-O-C Cleaning Procedures, DPF Regeneration in Parking, DPF Regeneration in Driving, DPF Onboard. NL102P's tool helps you re-awaken the engine power When the diesel p-articulates of the engine accumulate. It will save $800-$2500 for truck owners a year.
- 🍊➤【Excellent Oil Light Reset】NL102 PLUS support Oil service reset work on Cummings, Detroit, Maxxforce engine. when the replacement of engine oil is done, the truck system calculates when to change the engine oil and filter based on vehicle use. An oil change is required whenever indicated by the display, otherwise it will affect the engine maintenance and life. The NL102P truck scanner offers help to reset the Oil Life Reminder (Determine the Oil Service Light), ensure your driving safety.
- 🍐➤【All OBD/EOBD Diagnosis】NL102 PLUS supports both all 12V and all 24V truck, and it comes with 6 pin, 9 pin and 16 pin adapters for different interfaces. NL102 PLUS can read and earse the trouble codes, determine the MIL (check your Truck engine) and I/M Readiness, Freeze Frame, Live Data, O-xygen Sensor Test, On-Board Monitor, Vehicle Identification Info. Built in a DTC lookup library you can find the related code definition to help you determine if your car needs repair. In order to ensure that you can use the NL102P, please check the manual before purchasing.
- 🔥2024 TOP INTELLIGENT DIAGNOSTIC SCANNER FOR SEMI COMMERCIAL: ANCEL V5 HD obd2 scanner is specifically designed for 12V & 24V semi trucks,pickup trucks,heavy-duty trucks and 99% of commercial vehicles.you will enjoy✅All System Diagnostic;✅40+ Special Functions;✅ Full Bi-directional Test; ✅Advanced ECU Coding;✅Exclusive Remote Diagnosis Assistance;✅Full System Diagnostic ;✅Wider Vehicle Coverage;✅ Full HD OBD /OBDII /EOBD Modes;✅Top-level Hardware;✅>2 Yrs Free Update,Lifetime Tech Support
- 🚚40+ Resets with ABS SRS DPF Regen: ANCEL V5 HD includes 40+ resets for various systems, including ABS, SRS, DPF, EPB, BMS,DPF Regen, Injector Coding,Parameter Setting,Idle Speed Adjustment, Speed Limit Adjustment and more to fully meet your various needs. These resets can help reset the vehicle's systems to their default settings, eliminating any error codes or malfunctions that may be causing problems.Please send your VIN# to our 💌 amazon@anceltech.com 💌 to check compatibility.
- 🚛FULL BI-DIRECTIONAL CONTROL, GET YOU TO MALFUNCTIONS DIRECTLY:ANCEL V5 HD bidirectional scan tool supports bidirectional testing, which means it can both read and erase fault codes from the vehicle's ECUs.This feature saves time and money by eliminating the need for multiple scanners or tools.you can quickly identify whether the repair job works or not:Aftertreatment Test, Injector Test,Fuel Pump Test,Cylinder Test,Enigne State Monitor,A/C Compressor Test,Heated Oxygen Sensor Test and more.
- 🚜ADVANCED ECU CODING & PROGRAMMING:ANCEL V5 HD diesel truck scan tool comes with a powerful ECU programming and coding function, allowing you to reprogramme and decode the electronic control units (ECUs) of the vehicle.This feature is especially useful for technicians who need to update software,adjust parameters,or perform other modifications to the vehicle's electronic systems.🚦Note: ECU Coding is not universal to all cars, please check compatibility with VIN before order.
- 🚌OE-Level Full System Diagnostic:ANCEL V5 HD code reader is a professional-grade truck scanner that covers almost all the systems in semi-commercial vehicles, including engine, transmission, ABS, SRS, airbag,instrument panel, etc.It provides accurate and comprehensive diagnostic results,helping you quickly identify and solve vehicle problems,which are in compliance with J1939, 1708,ISO14230,ISO15765,ISO9141,ISO11898,E-J1850 VPW,SAE-J1850 PWM,J1587,CAN TP16,CAN TP20,AN-FD,and DOIP protocols.
- 🔥🔥🔥2024 New Functions Making X7 HD the Top Dog - Big Surprise!!! ANCEL X7 HD heavy duty truck scan tool 10 major functional advantages .✅>Full HDOBD/OBD2 Function ✅>ALL System Diagnostic ✅>40+ Reset Function ✅>Active Test / Bi-Directional Control✅>ECU Coding✅>Graphing Live Data✅>Wide Compatibility ✅>2 Yrs Free Update✅>Remote Operation✅>Bluetooth 5.0 & Wifi In addition, 8 major hardware advantages: ✅>6000 mAh✅>10.1 inch Tablet✅>2G RAM✅>32G ROM (Expandable to 128GB)✅>Data Record & Replay & Print✅>Android 10.0✅>Bluetooth 5.0 & Wifi✅>14 Languages
- 🚛Advanced ECU Coding & Programming - ANCEL X7 HD 10.1inch diesel truck scan tool is equipped with advanced ECU coding, supports Level calibration, Idle speed learning and Adjustment, Camshaft timing control learning, Control unit adaptations, Injector Codes, Read/Write VIN, Road speed limit optional vehicle speed set, etc... PLEASE NOTE that ECU codes are not compatible with all vehicles, please send us your VIN# to check vehicle compatibility.
- 🚛40+ Reset Functions & Bidirectional Control - 2024 newest top truck scanner diagnostic tool, comes with 40+ special services (ECU, Oil Reset, Injector Coding, EPB, ABS, SRS, Suspension, Throttle, etc. and always keep growing), which meet all your various needs for service and maintenance. Please send your VIN# to our 💌 amazon@anceltech.com 💌 to check compatibility.
- 🚛10 Inch All Systems Diesel Scanner & Full HDOBD/OBD2 Modes - ANCEL X7 HD diesel scanner diagnostic tool supports all systems scan, such as Engine, Brake, Retarder, TECU Transmission, Tachograph, ABS, SRS, TPMS, EPB, SAS, ESP, and other vehicle systems, comes with 10 obd2 service modes: read/erase error codes, Data Stream, I/M Readiness, Vehicle Information, Actuations, DTC Lookup, EVAP, view freeze frame, etc.
- 🚛OEM DPF Forced Regen & Cylinder Cutout Test & more - ANCEL X7 HD truck scanner not only supports DPF regeneration, DPF reset, DPF related information reset, DPR state reset, DPD forced regeneration etc, which helps you better solve the exhaust aftertreatment system problems, but also supports activate motor to do exhaust air in ABS Automatically. Moreover, it features TPMS activation, cylinder cut-off and learning functions.
- 🔎【Comprehensive Full Systems Diagnostic Tool For Truck】Launch Heavy Duty Truck Diagnostic Tool offers OE-Level diagnosis for all systems of heavy truck/Pickups/Bus/Van in compliance with OBD-II Communication Modes 1-10 and J1587, J1708 and J1939 protocols,Including Engine, Transmission, Drivetrain, Suspension, ABS, ESP, Cluster, E-xhaust, P-articular, Suspension, Braking System, Cab Climate, Body Control, Instrument Panel, Fuel System and more.
- 🔥【All OBD/EOBD Diagnosis】This truck scanner diagnostic tool supports both most 12V and 24V truck, and it comes with 6 pin, 9 pin and 16 pin adapters for different interfaces. Our truck scan tool can read codes, erase codes, I/M Readiness, Live data, EVAP Test. . . etc for obd2/eobd cars. Built in a DTC lookup library you can find the related code definition to help you determine if your car needs repair.
- 🚚【Wide Truck Applications】Heavy duty truck scan tool covers almost J1587, J1708 and J1939 protocols heavy duty trucks and OBD II vehicles. Such as Cummins, Paccar, Detroit, Perkins, International, Peterbilt, Allison, Eaton, Ford duty trucks and so on, Covers class 4 (14,001 lbs) through class 8 (33,000 lbs and over) heavy duty trucks. One that meets all the requirements! NOTE:Compatibility will vary on vehicles model and year, please send V-IN to check the compatibility before purchase.
- 💡【Friendly Design, Easy of Use】This heavy duty diagnostic scan tool is plug and play, simple and convenient, The excellent 2.8 inch LCD color screen makes it easy to view the displayed results and gives you a better overview of your car's problem areas and the identified codes. In addition, the processor is super-fast and responds without lagging, providing maximum comfort and efficiency in diagnostic and service work.
- ✨【3 YEARS WARRANTY & FREE LIFETIME UPDATES】The diesel truck scanner is exclusively designed for US truck. it's come With a full service functions and full systems and provides 24/7 technical support, 3 years warranty, 90-days free return for refund or replacement. This diesel scan tool is suitable for auto repair shops and technicians.No subscription fee and free lifetime updates.
- Powerful and Cost-Effective - An essential heavy duty truck scanner designed for heavy duty truck owner-operators and small commercial fleets. With the Diesel Decoder, just plug the diesel scan tool into the diagnostic port and pair with the free smartphone app to access in-depth HD diagnostic information.
- Swift and Adaptable - This heavy duty truck scanner recognizes both diagnostic trouble codes (DTCs) and brand-specific error codes for prevalent heavy-duty truck brands in North America, such as Freightliner, Peterbilt, Mack, Kenworth, Volvo, Western Star, among others and give the ability to perform DPF regens on select model years of Cummins, International, Detroit, Isuzu, Paccar, Mercedes, Hino and Mack/Volvo.
- Instant Repair Help - The diesel scan tool seamlessly connects to the Diesel Laptops comprehensive Diesel Repair Platform library so you can immediately start diagnosing and repairing any problems and get back on the road as soon as possible.
- Continuous Enhancement - Benefit from direct feature additions and updates via the app, our heavy duty truck scanner will continue to have functionality added over time. This removes the hassle of lengthy update processes and the financial strain of renewing costly diagnostic gear.
- 🌟【Run Your DPF Cleaner, Longer -Renew, Don't Replace!】Safeguard your truck from breakdowns and and high repair costs with focused DPF care. Opt for HD3400, featuring DPF regen, reset, DPR state control, and more, tailored for engines like Cummins, Detroit, Caterpillar, etc. Imagine this: easy and cost-effective DPF regen saving you from potential $10,000 to $30,000 in repairs. Unlock compliance-free operation for improved fuel efficiency, extended engine life, and significant cost savings
- 🚜【Maximize Caterpillar Engine Trucks' Potential!】HD3400 Plus diesel scanner, exclusively for Caterpillar engines (C7, C9, C11, C13, C15, C32, and more) commonly found in trucks like Caterpillar, Ford Pick-up, Freightliner, Peterbilt, Kenworth. Features include code reading/clearing, live data streaming, ECU retrieval, DPF regeneration and more. Unleash your Caterpillar engine's power!
- 🚛【Designed for Detroit Engine Trucks】ANCEL HD3400 heavy duty truck scan tool is compatible with a wide range of heavy duty commercial trucks – class 7 and class 8, medium duty trucks, light duty trucks and semi-trucks equipped with Detroit engines, including DD13, DD15, DD16, Series 50, Series 60, MBE 900, MBE 4000, OM501, OM502, DDDL 6, and DDDL 7.
- 🚐【Designed for Paccar Engine Trucks】ANCEL HD3400 heavy-duty truck scanner diagnostic tool is specifically designed for Paccar engines, including Paccar PX-7, PX-9, MX-11, MX-13. ❗Note: PACCAR engines post-2016 require a CAN-3 adapter for forced DPF regeneration. If you want to perform DPF regen for your PACCAR engines manufactured after 2016, please find us to get the additional CAN-3 adapter.
- 🌟【Unlock Advanced DPF Regeneration】Our diesel scanner diagnostic tool excels in DPF reset, providing active/forced regeneration and advanced DPF state control. Save time and money on DPF maintenance, making it the top choice for truck diagnostics. Elevate your DPF maintenance with our advanced features!
- 【Extensive Compatibility】After the upgrade, the compatibility is wider and more accurate! HD601 PRO heavy duty truck scanner supports all major truck models that comply with standard protocols (SAE J1939, SAE J1708, ISO 14230-4, ISO 15764-4 and ISO 9141-2, ISO 27145-4 and Euro6). Such as Cummins, Paccar, Detroit, Perkins, Freightliner, International, Peterbilt, Ford, Class 4-Class 8 trucks, etc. It also check engine diagnosis on most cars, minivans and light trucks from 1996 and latest.
- 【OE-Level Full System Diagnostic】HD601 PRO Diesel Scanner supports all system scans of heavy trucks compliant with standard protocols SAE J1939 & J1708, such as Engine, ABS, Transmission, Braking System, ESP, EPS, Fuel System, etc, It is a great scan tool for Cummins, Caterpillar, Detroit, Perkins, Maxxforce, BendixWabash, Wabaco, Haldex, Allison, Eaton heavy trucks, With this truck tool, you can get deep analysis data about the system and do some repairs by yourself, saving much time and money.
- 【Enhanced Diesel OBD Scanner】As a 2-in-1 code reader, it supports the latest ISO27145 and Euro6 protocols and enables diagnosis of car and truck engines. In addition to reading codes, clearing codes and displaying live data in a text or graphic format for trucks, you can also retrieve vehicle information, view freeze frames and look up DTCs. To ensure that this device works with different engines, it is also equipped with 6, 9 and 16 pin cables that allow you to easily turn off the CEL light.
- 【DTC Library】+【Life Time Free Update】The built-in DTC library allows you to retrieve the codes directly without searching for the definition in the book. Whether you are a professional mechanic or a DIY car owner, HD601 diesel scanner explains the existing problem, makes it easier for you to understand the codes definition and fix the problem faster. Plus, you get a lifetime free internet updates, so you always have the latest software for diagnostics in English and Spanish languages.
- 【Friendly Design, Easy of Use】This scanner is plug and play, simple and convenient, and very friendly for beginners. With improved buttons for easy menu navigation. The excellent 2.8 inch LCD color screen makes it easy to view the displayed results and gives you a better overview of your car's problem areas and the identified codes. In addition, the processor is super-fast and responds without lagging, providing maximum comfort and efficiency in diagnostic and service work.
- 【2024 NEWEST LAUNCH 1st Advanced Scan Tool Compatible With 12V&24V Vehicles】Design for Passenger&Commercial Vehicles 2 in1,work for Cars/Trucks/buses/trailers/excavators/diesel engine/pick-up/etc.
- 【J2534 Reprogramming with Smartlink C】Advanced OEM J2534 reprogramming,Helps access direct data online, replace existing software/firmware in ECU,program new ECUs and fix software-controlled issue.
- 【Over 60 Service Reset Functions + Bi-Directional + ECU Coding 】This scan tool can support ECU Coding,60+ reset service functions like SAS/EPB/TPMS/DPF/Oil/Brake/ABS Bleed, Injector coding, etc.
- 【2024 BEST Advanced Hardware & All Systems Diagnosis+Topology Display 】Support All systems Diagnostic including ENG, AT, ECM, TCM, ABS, SRS, BCM, BMS, TPMS, SAS, Fuel System, Light System and more.
- 【Wider Vehicle Coverage of 12V & 24V Vehicles + 24 Languages】LAUNCH X431 PRO3S+SMARTLINK HD automotive scanner is ALL-IN-ONE Scan Tool for 12V cars and 24V Heavy-duty trucks support CANFD & DOIP.
- 【Full Systems Heavy Duty Scanner Tool】:this heavy duty scanner tool supports Read DTC and Clear DTC, Live Data,Engine Check, Transmission, Drivetrain, Suspension, Cluster, Suspension, Braking System, Cab Climate, Body Control, Instrument Panel, Fuel System and more, which are in compliance with J1939, J1708 and J1587 protocols,
- 【OBD2/HDOBD/EOBD All Diagnosis】: supports both all 12V and all 24V truck, with 6 pin and 9 pin adapters for different interfaces.It support reading code, earsing trouble codes, Live Data, determine the MIL (check your Truck engine) and I/M Readiness, Freeze Frame, O2 Sensor Test, On-board Monitor, Vehicle Identification Info.It can lookup DTC, translates the related code's meaning to help you know what's wrong with the car.
- 【Suitable for Most Trucks】:diesel diagnostic scanner support all truck standard protocols SAEJ1939/ J1587/ J1708,it work on heavy duty trucks/ light truck/ mini vans/ buses/ pickups from1996 to now.
- 【CANBUS System】:Detect the CANBUS node, and easily find out the wrong modoles and lines.
- 【Professional Automotive Scanner Diagnostic Tools】:Designed specifically for HDOBD/OBD2/EOBD.This HD10 covers all the functions of HDOBD,OBD2,and EOBD. What is more important is that it provide the results correctly and quickly, and you can read the results with graghs, which make you easier to read.
- 👍【2024 Newest wide Coverage for Heavy truck】: With support for standard HD OBD protocols and customized protocols, ANCEL HD3400 PRO provides 98% coverage for heavy truck models in the US market, including those with Cummins, Detroit, Caterpillar, Paccar engines,and trucks like Ford, Autocar, western star, Freightliner, Kenworth, Peterbilt, caterpillar,Terex, Thomas, Sany, Komatsu, Agrifac , Isuzu, Fuso, Hino,Volvo and more.
- 🚛【Available for Cummins 】ANCEL HD3400 Pro is specifically designed to support a wide range of Cummins engines found in trucks like Ford, Volvo, Freightliner, Kenworth, and more, as well as Sany machinery, Agrifac vehicles, RVs, and more. Compatible with ISX, ISM, ISN, QSB, X12, ISB, ISC, ISD, ISG, ISK, ISL, X15, B6.7, L9, L9N, QSM11, and other popular models.
- 🚒【Available for Caterpillar】exclusively designed for Caterpillar engines (C7, C9, C11, C13, C15, C32, and more), you can perform top-notch diagnostics to keep your trucks running reliably. Compatible with popular truck models like Kenworth, Peterbilt, Freightliner, International, Mack, and Volvo.
- 🚛【Available for Paccar&Detroit】ANCEL HD3400 PRO is compatible with a wide range of engine types, including Detroit engines (Series 50, Series 55, Series 60, OM501, OM502, DD5, DD13, DD15, DD16,MBE 900, MBE 4000, DD8, DDDL 6, DDDL 7, CPC2, CPC02T, CPC04T, CPC302T and More) and Paccar engines(PX-7, PX-9, MX-11, MX-13 and more). like medium-duty or light-duty trucks, or even semi-trucks
- 🚒【Superb Lifetime Free Update,Best Bang For The Buck】ANCEL HD3400 PRO diesel code reader allow our customers get the latest version with free update via WIFI,With Lifetime Free Update,HD3400 PRO is way more valuable by comparing with the other OBD diagnosis,which can save hundreds of dollar for our customers!
Last update on 2024-04-11 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Defect / Noncompliance Information Report (Section 573.6) FL-934 Date of Submission: May 16, 2022 Manufacturer: Daimler Truck North America LLC P.O. BOX 3849 Portland, Oregon 97208 Type of Report: X Safety Defect ⃝ Non-Compliance Vehicle Information Model Yr. Start: 2021 Model Yr. End: 2022 Make: Freightliner Custom Chassis Corporation (FCCC) Model: MT50e Production Dates: Begin: June 22, 2021 End: April 11, 2022 Descriptive Information: Supplier alerted FCCC that they had discovered a potential for failure in certain FCCC MT50e model walk-in vans are equipped with a rotary knob managing transmission shift position functionality. If a potentiometer in the switch is damaged, a plausibility error could occur, causing the part to send out a message that will be coded as drive (D) position rather than the appropriate error (ERR) position. NOTE: Identify by body style or type. – MT50e, electric walk-in van Basis for Determination of the Recall Population: At the current time, all MT50e electric walk-in vans built from June 22, 2021 to April 11, 2022 are included in the recall population. However, as DTNA continues to investigate, the population may be decreased. The supplier of the multi-switch notified DTNA of the specific part with a potential defect. Number potentially involved: 19 Estimated percentage of involved with defect: 100% Defect / Noncompliance Description For this Defect/Noncompliance: Describe the defect or noncompliance: MT50e electric walk-in vans are equipped with a rotary DNRP selector that has two potentiometers inside. Out of an abundance of caution, the supplier did fault-injection testing to determine what would happen in certain unlikely failure modes. In one case, the supplier reported that an unlikely failure mode, if one of the potentiometers is damaged, it could cause a plausibility error that the part would send out a message coded as the D position rather than the appropriate ERR position. Therefore, if this part has damage, there is potential that the vehicle could have Drive selected without the driver’s intent. Describe the safety risk: Failure mode could result in an unintended shift into drive. Identify any warning which can precede or occur: No known warning. If applicable, identify the manufacture of the defective or noncompliant component.: BCS Automotive Interface Solutions (BCS-AIS; BCS) Involved Components Component Name: Stalk Switch Right Shifter Component Description: Stalk Switch Right Shifter with Park Position Component Part Number: DTNA: 06-87751-008 BCS: 17045623-01 Chronology of Defect / Noncompliance Determination Provide the chronology of events leading up to the defect decision or test data for the noncompliance decision: On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world. Identify the Remedy Describe the defect/noncompliance remedy program, including the manufacture’s plan for reimbursement. Inspection and repair of the Stalk Switch Right Shifter, if required, will be performed by Daimler Truck North America authorized service facilities. Daimler Truck North America shall be offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which will be posted with owner’s notification letter. Owners are directed to seek reimbursement through authorized dealers. Identify the Recall Schedule Describe the recall schedule for notifications.: Customer notification will be made by first class mail using Daimler Trucks North America records to determine the customers affected. Planned Dealer Notification Begin Date: July 14, 2022 Planned Dealer Notification End Date: July 14, 2022 Planned Owner Notification Begin Date: July 14, 2022 Planned Owner Notification End Date: July 14, 2022 Does DTNA plan to file inconsequentiality petition? ⃝ Yes X No Manufacturer’s identification code for this recall (if applicable): FL-934 DTNA Representative; Tiffani Torgeson Manager, Compliance and Regulatory Affairs
**************************************************************************************************************
Defect / Noncompliance Information Report (Section 573.6) FL-934 Date of Submission: May 16, 2022 Manufacturer: Daimler Truck North America LLC P.O. BOX 3849 Portland, Oregon 97208 Type of Report: X Safety Defect ⃝ Non-Compliance Vehicle Information Model Yr. Start: 2021 Model Yr. End: 2022 Make: Freightliner Custom Chassis Corporation (FCCC) Model: MT50e Production Dates: Begin: June 22, 2021 End: April 11, 2022 Descriptive Information: Supplier alerted FCCC that they had discovered a potential for failure in certain FCCC MT50e model walk-in vans are equipped with a rotary knob managing transmission shift position functionality. If a potentiometer in the switch is damaged, a plausibility error could occur, causing the part to send out a message that will be coded as drive (D) position rather than the appropriate error (ERR) position. NOTE: Identify by body style or type. – MT50e, electric walk-in van Basis for Determination of the Recall Population: At the current time, all MT50e electric walk-in vans built from June 22, 2021 to April 11, 2022 are included in the recall population. However, as DTNA continues to investigate, the population may be decreased. The supplier of the multi-switch notified DTNA of the specific part with a potential defect. Number potentially involved: 23 Estimated percentage of involved with defect: 100% Defect / Noncompliance Description For this Defect/Noncompliance: Describe the defect or noncompliance: MT50e electric walk-in vans are equipped with a rotary DNRP selector that has two potentiometers inside. Out of an abundance of caution, the supplier did fault-injection testing to determine what would happen in certain unlikely failure modes. In one case, the supplier reported that an unlikely failure mode, if one of the potentiometers is damaged, it could cause a plausibility error that the part would send out a message coded as the D position rather than the appropriate ERR position. Therefore, if this part has damage, there is potential that the vehicle could have Drive selected without the driver’s intent, contributing to an increased risk for crash or injury. Describe the safety risk: Failure mode could result in an unintended shift into drive. Identify any warning which can precede or occur: No known warning. If applicable, identify the manufacture of the defective or noncompliant component.: BCS Automotive Interface Solutions (BCS-AIS; BCS) Involved Components Component Name: Stalk Switch Right Shifter Component Description: Stalk Switch Right Shifter with Park Position Component Part Number: DTNA: 06-87751-008 BCS: 17045623-01 Component’s country of origin: PCB is assembled and flashed in Radolfzell, Germany and the final Assembly is done in Benesov, Czech Republic Business address: BCS Automotive Interface Solutions GmbH Industriestr. 2-8 78315 Radolfzell Germany Business telephone number: +49 7732 809 798 Chronology of Defect / Noncompliance Determination Provide the chronology of events leading up to the defect decision or test data for the noncompliance decision: On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. On June 3, 2022, we became aware of additional units that had shipped prior to the recall determination and amended the population accordingly. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world. Identify the Remedy Describe the defect/noncompliance remedy program, including the manufacture’s plan for reimbursement. Inspection and repair of the Stalk Switch Right Shifter, if required, will be performed by Daimler Truck North America authorized service facilities. Daimler Truck North America shall be offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which will be posted with owner’s notification letter. Owners are directed to seek reimbursement through authorized dealers. Identify the Recall Schedule Describe the recall schedule for notifications.: Customer notification will be made by first class mail using Daimler Trucks North America records to determine the customers affected. Planned Dealer Notification Begin Date: July 14, 2022 Planned Dealer Notification End Date: July 14, 2022 Planned Owner Notification Begin Date: July 14, 2022 Planned Owner Notification End Date: July 14, 2022 Does DTNA plan to file inconsequentiality petition? ⃝ Yes X No Manufacturer’s identification code for this recall (if applicable): FL-934 DTNA Representative; Tiffani Torgeson Manager, Compliance and Regulatory Affairs
**************************************************************************************************************
Defect / Noncompliance Information Report (Section 573.6) FL-934 Date of Submission: May 16, 2022 Manufacturer: Daimler Truck North America LLC P.O. BOX 3849 Portland, Oregon 97208 Type of Report: X Safety Defect ⃝ Non-Compliance Vehicle Information Model Yr. Start: 2021 Model Yr. End: 2022 Make: Freightliner Custom Chassis Corporation (FCCC) Model: MT50e Production Dates: Begin: November 5, 2020 End: April 11, 2022 Descriptive Information: Supplier alerted FCCC that they had discovered a potential for failure in certain FCCC MT50e model walk-in vans are equipped with a rotary knob managing transmission shift position functionality. If a potentiometer in the switch is damaged, a plausibility error could occur, causing the part to send out a message that will be coded as drive (D) position rather than the appropriate error (ERR) position. NOTE: Identify by body style or type. – MT50e, electric walk-in van Basis for Determination of the Recall Population: At the current time, all MT50e electric walk-in vans built from November 5, 2020 to April 11, 2022 are included in the recall population. However, as DTNA continues to investigate, the population may be decreased. The supplier of the multi-switch notified DTNA of the specific part with a potential defect. Number potentially involved: 23 Estimated percentage of involved with defect: 100% Defect / Noncompliance Description For this Defect/Noncompliance: Describe the defect or noncompliance: MT50e electric walk-in vans are equipped with a rotary DNRP selector that has two potentiometers inside. Out of an abundance of caution, the supplier did fault-injection testing to determine what would happen in certain unlikely failure modes. In one case, the supplier reported that an unlikely failure mode, if one of the potentiometers is damaged, it could cause a plausibility error that the part would send out a message coded as the D position rather than the appropriate ERR position. Therefore, if this part has damage, there is potential that the vehicle could have Drive selected without the driver’s intent, contributing to an increased risk for crash or injury. Describe the safety risk: Failure mode could result in an unintended shift into drive. Identify any warning which can precede or occur: No known warning. If applicable, identify the manufacture of the defective or noncompliant component.: BCS Automotive Interface Solutions (BCS-AIS; BCS) Involved Components Component Name: Stalk Switch Right Shifter Component Description: Stalk Switch Right Shifter with Park Position Component Part Number: DTNA: 06-87751-008 BCS: 17045623-01 Component’s country of origin: PCB is assembled and flashed in Radolfzell, Germany and the final Assembly is done in Benesov, Czech Republic Business address: BCS Automotive Interface Solutions GmbH Industriestr. 2-8 78315 Radolfzell Germany Business telephone number: +49 7732 809 798 Chronology of Defect / Noncompliance Determination Provide the chronology of events leading up to the defect decision or test data for the noncompliance decision: On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. On June 3, 2022, we became aware of additional units that had shipped prior to the recall determination and amended the population accordingly. On June 27, 2022, we amended the start dates to match the population update from June 3, 2020, no impact to vehicle population. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world. Identify the Remedy Describe the defect/noncompliance remedy program, including the manufacture’s plan for reimbursement. Inspection and repair of the Stalk Switch Right Shifter, if required, will be performed by Daimler Truck North America authorized service facilities. Daimler Truck North America shall be offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which will be posted with owner’s notification letter. Owners are directed to seek reimbursement through authorized dealers. Identify the Recall Schedule Describe the recall schedule for notifications.: Customer notification will be made by first class mail using Daimler Trucks North America records to determine the customers affected. Planned Dealer Notification Begin Date: July 14, 2022 Planned Dealer Notification End Date: July 14, 2022 Planned Owner Notification Begin Date: July 14, 2022 Planned Owner Notification End Date: July 14, 2022 Does DTNA plan to file inconsequentiality petition? ⃝ Yes X No Manufacturer’s identification code for this recall (if applicable): FL-934 DTNA Representative; Sam Geser Manager, Compliance and Regulatory Affairs
**************************************************************************************************************
Defect / Noncompliance Information Report (Section 573.6) FL-934 Date of Submission: May 16, 2022 Manufacturer: Daimler Truck North America LLC P.O. BOX 3849 Portland, Oregon 97208 Type of Report: X Safety Defect ⃝ Non-Compliance Vehicle Information Model Yr. Start: 2021 Model Yr. End: 2022 Make: Freightliner Custom Chassis Corporation (FCCC) Model: MT50e Production Dates: Begin: June 22, 2021 End: April 11, 2022 Descriptive Information: Supplier alerted FCCC that they had discovered a potential for failure in certain FCCC MT50e model walk-in vans are equipped with a rotary knob managing transmission shift position functionality. If a potentiometer in the switch is damaged, a plausibility error could occur, causing the part to send out a message that will be coded as drive (D) position rather than the appropriate error (ERR) position. NOTE: Identify by body style or type. – MT50e, electric walk-in van Basis for Determination of the Recall Population: At the current time, all MT50e electric walk-in vans built from June 22, 2021 to April 11, 2022 are included in the recall population. However, as DTNA continues to investigate, the population may be decreased. The supplier of the multi-switch notified DTNA of the specific part with a potential defect. Number potentially involved: 19 Estimated percentage of involved with defect: 100% Defect / Noncompliance Description For this Defect/Noncompliance: Describe the defect or noncompliance: MT50e electric walk-in vans are equipped with a rotary DNRP selector that has two potentiometers inside. Out of an abundance of caution, the supplier did fault-injection testing to determine what would happen in certain unlikely failure modes. In one case, the supplier reported that an unlikely failure mode, if one of the potentiometers is damaged, it could cause a plausibility error that the part would send out a message coded as the D position rather than the appropriate ERR position. Therefore, if this part has damage, there is potential that the vehicle could have Drive selected without the driver’s intent, contributing to an increased risk for crash or injury. Describe the safety risk: Failure mode could result in an unintended shift into drive. Identify any warning which can precede or occur: No known warning. If applicable, identify the manufacture of the defective or noncompliant component.: BCS Automotive Interface Solutions (BCS-AIS; BCS) Involved Components Component Name: Stalk Switch Right Shifter Component Description: Stalk Switch Right Shifter with Park Position Component Part Number: DTNA: 06-87751-008 BCS: 17045623-01 Component’s country of origin: PCB is assembled and flashed in Radolfzell, Germany and the final Assembly is done in Benesov, Czech Republic Business address: BCS Automotive Interface Solutions GmbH Industriestr. 2-8 78315 Radolfzell Germany Business telephone number: +49 7732 809 798 Chronology of Defect / Noncompliance Determination Provide the chronology of events leading up to the defect decision or test data for the noncompliance decision: On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world. Identify the Remedy Describe the defect/noncompliance remedy program, including the manufacture’s plan for reimbursement. Inspection and repair of the Stalk Switch Right Shifter, if required, will be performed by Daimler Truck North America authorized service facilities. Daimler Truck North America shall be offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which will be posted with owner’s notification letter. Owners are directed to seek reimbursement through authorized dealers. Identify the Recall Schedule Describe the recall schedule for notifications.: Customer notification will be made by first class mail using Daimler Trucks North America records to determine the customers affected. Planned Dealer Notification Begin Date: July 14, 2022 Planned Dealer Notification End Date: July 14, 2022 Planned Owner Notification Begin Date: July 14, 2022 Planned Owner Notification End Date: July 14, 2022 Does DTNA plan to file inconsequentiality petition? ⃝ Yes X No Manufacturer’s identification code for this recall (if applicable): FL-934 DTNA Representative; Tiffani Torgeson Manager, Compliance and Regulatory Affairs
**************************************************************************************************************
Daimler Trucks North America, LLC 4747 N. Channel Avenue Portland OR 97217-7699 Phone: 503-745-8000 June 30, 2022 Michelle Rice Recall Analyst Department of Transportation National Highway Traffic Safety Administration 1200 New Jersey Avenue SE., Washington, DC 20590 Office: 202-366-1060 Subject: Freightliner Custom Chassis Corp. MT50e BCS Stalk Stock Switch Error NHTSA NS No. 22V-340 Manufacturer number: FL-934 Ms. Rice, There will be no publications for safety recall 22V-340. All vehicles within this recall campaign have been repaired prior to the publication of a Dealer’s Bulletin or Owner Notification. All impacted serial numbers were inspected/repaired on 6/7/2022. Please contact me if you have any questions. Sincerely, Sam Geser Product Defect Investigation Engineering manager Compliance and Regulatory Affairs Daimler Trucks North America Sam Geser Product Defect Investigation Engineering Manager Compliance and Regulatory Affairs
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-340 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Daimler Trucks North America, LLC Submission Date : JUN 03, 2022 NHTSA Recall No. : 22V-340 Manufacturer Recall No. : FL934 Manufacturer Information : Manufacturer Name : Daimler Trucks North America, LLC Address : 4747 N. Channel Avenue Portland OR 97217-3849 Company phone : 800-745-8000 Population : Number of potentially involved : 19 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2021-2022 FCCC MT50e Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : Power Train : NR Descriptive Information : Supplier alerted FCCC that they had discovered a potential for failure in certain FCCC MT50e model walk-in vans are equipped with a rotary knob managing transmission shift position functionality. If a potentiometer in the switch is damaged, a plausibility error could occur, causing the part to send out a message that will be coded as drive (D) position rather than the appropriate error (ERR) position. Production Dates : JUN 22, 2021 – APR 11, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : MT50e electric walk-in vans are equipped with a rotary DNRP selector that has two potentiometers inside. Out of an abundance of caution, the supplier did fault-injection testing to determine what would happen in certain unlikely failure modes. In one case, the supplier reported that an unlikely failure mode, if one of the potentiometers is damaged, it could cause a plausibility error that the part would send out a message coded as the D position rather than the appropriate ERR position. Therefore, if this part has damage, there is potential that the vehicle could have Drive selected without the driver’s intent, contributing to an increased risk for crash or injury. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : Failure mode could result in an unintended shift into drive. Description of the Cause : NR Part 573 Safety Recall Report 22V-340 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Identification of Any Warning that can Occur : No known warning. Involved Components : Component Name 1 : Stalk Switch Right Shifter Component Description : Stalk Switch Right Shifter with Park Position Component Part Number : 06-87751-008 Supplier Identification : Component Manufacturer Name : BCS Automotive Interface Solutions Address : Industriestr. 2-8 Germany Foreign States 78315 Country : Germany Chronology : On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. On June 3, 2022, we became aware of additional units that had shipped prior to the recall determination and amended the population accordingly. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world. Part 573 Safety Recall Report 22V-340 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Remedy : Description of Remedy Program : Inspection and repair of the Stalk Switch Right Shifter, if required, will be performed by Daimler Truck North America authorized service facilities. Daimler Truck North America shall be offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which will be posted with owner’s notification letter. Owners are directed to seek reimbursement through authorized dealers. How Remedy Component Differs from Recalled Component : NR Identify How/When Recall Condition was Corrected in Production : NR Recall Schedule : Description of Recall Schedule : Customer notification will be made by first class mail using Daimler Trucks North America records to determine the customers affected. Planned Dealer Notification Date : JUL 14, 2022 – JUL 14, 2022 Planned Owner Notification Date : JUL 14, 2022 – JUL 14, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-340 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Daimler Trucks North America, LLC Submission Date : JUN 04, 2022 NHTSA Recall No. : 22V-340 Manufacturer Recall No. : FL934 Manufacturer Information : Manufacturer Name : Daimler Trucks North America, LLC Address : 4747 N. Channel Avenue Portland OR 97217-3849 Company phone : 800-745-8000 Population : Number of potentially involved : 23 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2021-2022 FCCC MT50e Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : Power Train : NR Descriptive Information : Supplier alerted FCCC that they had discovered a potential for failure in certain FCCC MT50e model walk-in vans are equipped with a rotary knob managing transmission shift position functionality. If a potentiometer in the switch is damaged, a plausibility error could occur, causing the part to send out a message that will be coded as drive (D) position rather than the appropriate error (ERR) position. Production Dates : JUN 22, 2021 – APR 11, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : MT50e electric walk-in vans are equipped with a rotary DNRP selector that has two potentiometers inside. Out of an abundance of caution, the supplier did fault-injection testing to determine what would happen in certain unlikely failure modes. In one case, the supplier reported that an unlikely failure mode, if one of the potentiometers is damaged, it could cause a plausibility error that the part would send out a message coded as the D position rather than the appropriate ERR position. Therefore, if this part has damage, there is potential that the vehicle could have Drive selected without the driver’s intent, contributing to an increased risk for crash or injury. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : Failure mode could result in an unintended shift into drive. Description of the Cause : NR Part 573 Safety Recall Report 22V-340 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Identification of Any Warning that can Occur : No known warning. Involved Components : Component Name 1 : Stalk Switch Right Shifter Component Description : Stalk Switch Right Shifter with Park Position Component Part Number : 06-87751-008 Supplier Identification : Component Manufacturer Name : BCS Automotive Interface Solutions Address : Industriestr. 2-8 Germany Foreign States 78315 Country : Germany Chronology : On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. On June 3, 2022, we became aware of additional units that had shipped prior to the recall determination and amended the population accordingly. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world. Part 573 Safety Recall Report 22V-340 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Remedy : Description of Remedy Program : Inspection and repair of the Stalk Switch Right Shifter, if required, will be performed by Daimler Truck North America authorized service facilities. Daimler Truck North America shall be offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which will be posted with owner’s notification letter. Owners are directed to seek reimbursement through authorized dealers. How Remedy Component Differs from Recalled Component : NR Identify How/When Recall Condition was Corrected in Production : NR Recall Schedule : Description of Recall Schedule : Customer notification will be made by first class mail using Daimler Trucks North America records to determine the customers affected. Planned Dealer Notification Date : JUL 14, 2022 – JUL 14, 2022 Planned Owner Notification Date : JUL 14, 2022 – JUL 14, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-340 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Daimler Trucks North America, LLC Submission Date : JUN 27, 2022 NHTSA Recall No. : 22V-340 Manufacturer Recall No. : FL934 Manufacturer Information : Manufacturer Name : Daimler Trucks North America, LLC Address : 4747 N. Channel Avenue Portland OR 97217-3849 Company phone : 800-745-8000 Population : Number of potentially involved : 23 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2021-2022 FCCC MT50e Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : Power Train : NR Descriptive Information : Supplier alerted FCCC that they had discovered a potential for failure in certain FCCC MT50e model walk-in vans are equipped with a rotary knob managing transmission shift position functionality. If a potentiometer in the switch is damaged, a plausibility error could occur, causing the part to send out a message that will be coded as drive (D) position rather than the appropriate error (ERR) position. Production Dates : NOV 05, 2020 – APR 11, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : MT50e electric walk-in vans are equipped with a rotary DNRP selector that has two potentiometers inside. Out of an abundance of caution, the supplier did fault-injection testing to determine what would happen in certain unlikely failure modes. In one case, the supplier reported that an unlikely failure mode, if one of the potentiometers is damaged, it could cause a plausibility error that the part would send out a message coded as the D position rather than the appropriate ERR position. Therefore, if this part has damage, there is potential that the vehicle could have Drive selected without the driver’s intent, contributing to an increased risk for crash or injury. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : Failure mode could result in an unintended shift into drive. Description of the Cause : NR Part 573 Safety Recall Report 22V-340 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Identification of Any Warning that can Occur : No known warning. Involved Components : Component Name 1 : Stalk Switch Right Shifter Component Description : Stalk Switch Right Shifter with Park Position Component Part Number : 06-87751-008 Supplier Identification : Component Manufacturer Name : BCS Automotive Interface Solutions Address : Industriestr. 2-8 Germany Foreign States 78315 Country : Germany Chronology : On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. On June 3, 2022, we became aware of additional units that had shipped prior to the recall determination and amended the population accordingly. On June 27, 2022, we amended the start dates to match the population update from June 3, 2020, no impact to vehicle population. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world. Part 573 Safety Recall Report 22V-340 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Remedy : Description of Remedy Program : Inspection and repair of the Stalk Switch Right Shifter, if required, will be performed by Daimler Truck North America authorized service facilities. Daimler Truck North America shall be offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which will be posted with owner’s notification letter. Owners are directed to seek reimbursement through authorized dealers. How Remedy Component Differs from Recalled Component : NR Identify How/When Recall Condition was Corrected in Production : NR Recall Schedule : Description of Recall Schedule : Customer notification will be made by first class mail using Daimler Trucks North America records to determine the customers affected. Planned Dealer Notification Date : JUL 14, 2022 – JUL 14, 2022 Planned Owner Notification Date : JUL 14, 2022 – JUL 14, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-340 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Daimler Trucks North America, LLC Submission Date : MAY 25, 2022 NHTSA Recall No. : 22V-340 Manufacturer Recall No. : FL934 Manufacturer Information : Manufacturer Name : Daimler Trucks North America, LLC Address : 4747 N. Channel Avenue Portland OR 97217-3849 Company phone : 800-745-8000 Population : Number of potentially involved : 19 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2021-2022 FCCC MT50e Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : Power Train : NR Descriptive Information : Supplier alerted FCCC that they had discovered a potential for failure in certain FCCC MT50e model walk-in vans are equipped with a rotary knob managing transmission shift position functionality. If a potentiometer in the switch is damaged, a plausibility error could occur, causing the part to send out a message that will be coded as drive (D) position rather than the appropriate error (ERR) position. Production Dates : JUN 22, 2021 – APR 11, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : MT50e electric walk-in vans are equipped with a rotary DNRP selector that has two potentiometers inside. Out of an abundance of caution, the supplier did fault-injection testing to determine what would happen in certain unlikely failure modes. In one case, the supplier reported that an unlikely failure mode, if one of the potentiometers is damaged, it could cause a plausibility error that the part would send out a message coded as the D position rather than the appropriate ERR position. Therefore, if this part has damage, there is potential that the vehicle could have Drive selected without the driver’s intent, contributing to an increased risk for crash or injury. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : Failure mode could result in an unintended shift into drive. Description of the Cause : NR Part 573 Safety Recall Report 22V-340 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Identification of Any Warning that can Occur : No known warning. Involved Components : Component Name 1 : Stalk Switch Right Shifter Component Description : Stalk Switch Right Shifter with Park Position Component Part Number : 06-87751-008 Supplier Identification : Component Manufacturer Name : BCS Automotive Interface Solutions Address : Industriestr. 2-8 Germany Foreign States 78315 Country : Germany Chronology : On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world. Description of Remedy : Description of Remedy Program : Inspection and repair of the Stalk Switch Right Shifter, if required, will be performed by Daimler Truck North America authorized service facilities. Daimler Truck North America shall be offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which will be posted with owner’s notification letter. Owners are directed to seek reimbursement through authorized dealers. Part 573 Safety Recall Report 22V-340 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 How Remedy Component Differs from Recalled Component : NR Identify How/When Recall Condition was Corrected in Production : NR Recall Schedule : Description of Recall Schedule : Customer notification will be made by first class mail using Daimler Trucks North America records to determine the customers affected. Planned Dealer Notification Date : JUL 14, 2022 – JUL 14, 2022 Planned Owner Notification Date : JUL 14, 2022 – JUL 14, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-340 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Daimler Trucks North America, LLC Submission Date : MAY 16, 2022 NHTSA Recall No. : 22V-340 Manufacturer Recall No. : FL934 Manufacturer Information : Manufacturer Name : Daimler Trucks North America, LLC Address : 4747 N. Channel Avenue Portland OR 97217-3849 Company phone : 800-745-8000 Population : Number of potentially involved : 19 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2021-2022 FCCC MT50e Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : Power Train : NR Descriptive Information : Supplier alerted FCCC that they had discovered a potential for failure in certain FCCC MT50e model walk-in vans are equipped with a rotary knob managing transmission shift position functionality. If a potentiometer in the switch is damaged, a plausibility error could occur, causing the part to send out a message that will be coded as drive (D) position rather than the appropriate error (ERR) position. Production Dates : JUN 22, 2021 – APR 11, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : MT50e electric walk-in vans are equipped with a rotary DNRP selector that has two potentiometers inside. Out of an abundance of caution, the supplier did fault-injection testing to determine what would happen in certain unlikely failure modes. In one case, the supplier reported that an unlikely failure mode, if one of the potentiometers is damaged, it could cause a plausibility error that the part would send out a message coded as the D position rather than the appropriate ERR position. Therefore, if this part has damage, there is potential that the vehicle could have Drive selected without the driver’s intent. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : Failure mode could result in an unintended shift into drive. Description of the Cause : NR Identification of Any Warning that can Occur : No known warning. Part 573 Safety Recall Report 22V-340 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Involved Components : Component Name 1 : Stalk Switch Right Shifter Component Description : Stalk Switch Right Shifter with Park Position Component Part Number : 06-87751-008 Supplier Identification : Component Manufacturer Name : BCS Automotive Interface Solutions Address : NR NR Country : NR Chronology : On a document dated May 9, 2022, BCS alerted DTNA of DNPR Plausibility Error Observations. Additional communication from the supplier (dated May 10, 2022) was received advising to limit all test vehicles equipped with this part to test track evaluation environments due to the Plausibility Error. DTNA promptly began an investigation; no warranty claims or other communications were found for this type of failure. May 13, 2022 out of an abundance of caution, DTNA decided to conduct a voluntary recall on MT50e walk-in vans. To date: DTNA has no reason to believe that the fault, artificially created in supplier fault injection testing, has ever occurred in the real world. Description of Remedy : Description of Remedy Program : Inspection and repair of the Stalk Switch Right Shifter, if required, will be performed by Daimler Truck North America authorized service facilities. Daimler Truck North America shall be offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which will be posted with owner’s notification letter. Owners are directed to seek reimbursement through authorized dealers. How Remedy Component Differs from Recalled Component : NR Identify How/When Recall Condition was Corrected in Production : NR Part 573 Safety Recall Report 22V-340 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Recall Schedule : Description of Recall Schedule : Customer notification will be made by first class mail using Daimler Trucks North America records to determine the customers affected. Planned Dealer Notification Date : JUL 14, 2022 – JUL 14, 2022 Planned Owner Notification Date : JUL 14, 2022 – JUL 14, 2022 * NR – Not Reported
SEOCONTENT-END