“This site contains affiliate links for which OEMDTC may be compensated” |
November 26, 2021 NHTSA CAMPAIGN NUMBER: 21V930000
Vehicle May Roll Backwards due to Hesitation/Stall
A stall or hesitation can cause the vehicle to roll backwards, increasing the risk of a crash or personal injury.
NHTSA Campaign Number: 21V930
Manufacturer Autocar, LLC
Components EQUIPMENT
Potential Number of Units Affected 16
Summary
Autocar, LLC. (Autocar) is recalling certain 2020 Xpeditor vehicles up-fitted with an aftermarket power take off (PTO). The engine may stall or hesitate when operated from the right-side stand-up position with the PTO system engaged.
Remedy
Autocar will install a hill start aide system, free of charge. Owner notification letters were mailed January 24, 2022. Owners may contact Autocar customer service at 1-888-218-3611 or 1-877-973-3486. Autocar’s number for this recall is ACX-2107. Note: This recall is an expansion of recall 20V-496.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
SUBJECT:
Autocar, LLC has determined that a defect regarding a potential stall/hesitation may exist on certain Xpeditor® vehicles during launch, when operated from the right-side stand-up position with the hydraulic system engaged.
SAFETY RECALL INFORMATION:
This document provides work instructions to install a Hill Start Aid system.
VEHICLES AFFECTED:
There are 46, 2019-2020 model year Xpeditor® chassis manufactured between June 7, 2018 and November 25, 2019 with non-sequential serial numbers in the range of 228128 through 232658. To determine if a vehicle is affected by this Recall, log in to the Autocar Warranty Management System at www.autocartruck.com. From the main menu, select “View Recalls/Service Programs” and look for the Autocar Recall number above. An excel file will be accessible with the VIN list of affected vehicles. Alternatively, to determine if a single vehicle is affected, select “VIN Profile” from the main menu in the Autocar Warranty Management System. In the “Chassis Number” field, enter the last 6 of the VIN. Once the VIN profile is displayed, scroll down to the “Recall/Service Program Information” section to determine if the Recall is open.
SERVICE RESPONSIBILITY:
Service sites must perform this Recall on affected vehicles at no charge to the owner regardless of vehicle mileage, age, or ownership. If a vehicle affected by this Recall is taken into or is currently in your vehicle inventory, or at your center for service, you must perform this Recall before the vehicle is sold or released to the owner.
November 26, 2021
Complete Chronology
ACX-2005/ACX-2107
On or about February 5, 2020, Autocar received information regarding two CNG units and one diesel unit for certain vehicles that were custom built for one customer. The information provided indicated potential concerns in connection with a lack of acceleration. An internal corrective action was initiated to analyze the alleged condition.
On or about February 6, 2020, additional information was added to the corrective action to additionally evaluate the sales order group of 48 units to the one customer, and Autocar’s field service team proceeded with its investigation.
On or about February 12, 2020, the Autocar field service team preliminarily identified that the “Vehicle Accelerator Management” parameter was unexpectedly enabled on the diesel unit, and Autocar tentatively identified that the parameter had not been enabled by Autocar prior to first sale to the customer. When this feature was disabled, the reported concern was eliminated, and the customer returned the vehicle to service. Further analysis in or about mid-March 2020 confirmed Autocar’s February 2020 preliminary view that the accelerator management parameter was not enabled by Autocar. As a result, Autocar reasonably determined that this was an isolated incident. Autocar subsequently moved the diesel unit matter to a separate corrective action, and closed it as resolved.
Between late March 2020 and June 2020, the COVID-19 global pandemic restricted Autocar’s reasonable ability to conduct its normal investigative process, including travel restrictions, mandatory shelter in place orders, and related government ordered restrictions. Despite these government ordered restrictions, Autocar was in full communication with the customer, and in good faith, Autocar did not reasonably assess the reported condition as an unreasonable risk to safety.
On or about June 25, 2020, Autocar was contacted by NHTSA requesting a discussion regarding certain customer complaints reported to the agency. On July 1, 2020, Autocar held a telephone discussion with NHTSA regarding customer complaints and Autocar’s analysis of the matter to date. Following a good faith discussion with the agency, and upon further analysis, Autocar increased the total suspect population to 78. Autocar actively communicated and cooperated with NHTSA in July and August 2020, during which time Autocar continued to reasonably assess the reported condition for its potential safety risk. With COVID-19 government ordered restrictions somewhat relaxed, in July 2020, Autocar field service team participated in ride along monitoring with the customer and obtained data from the engine ECM while the reported concern was active. In late July and early August 2020, Autocar analyzed the collected customer data whilst NHTSA and Autocar continued to have cooperation and communication about the subject issues. On August 17, 2020, Autocar decided to perform a voluntary safety recall. Update for ACX-2107: November 18, 2021 Autocar Identified an additional 16 units that could be subject to the original recall and out of an abundance of caution decided to perform a voluntary safety recall for all 16 additional units.
Chronology :
On or about February 5, 2020, Autocar received information regarding two CNG units and one diesel unit for certain vehicles that were custom built for one customer. The information provided indicated potential concerns in connection with a lack of acceleration. An internal corrective action was initiated to analyze the alleged condition. On or about February 6, 2020, additional information was added to the corrective action to additionally evaluate the sales order group of 48 units to the one customer, and Autocar’s field service team proceeded with its investigation. On or about February 12, 2020, the Autocar field service team preliminarily identified that the “Vehicle Accelerator Management” parameter was unexpectedly enabled on the diesel unit, and Autocar tentatively identified that the parameter had not been enabled by Autocar prior to first sale to the customer. When this feature was disabled, the reported concern was eliminated, and the customer returned the vehicle to service. Further analysis in or about mid-March 2020 confirmed Autocar’s February 2020 preliminary view that the accelerator management parameter was not enabled by Autocar. As a result, Autocar reasonably determined that this was an isolated incident. Autocar subsequently moved the diesel unit matter to a separate corrective action, and closed it as resolved. Between late March 2020 and June 2020, the COVID-19 global pandemic restricted Autocar’s reasonable ability to conduct its normal investigative process, including travel restrictions, mandatory shelter in place orders, and related government ordered restrictions. Despite these government ordered restrictions, Autocar was in full communication with the customer, and in good faith, Autocar did not reasonably assess the reported condition as an unreasonable risk to safety. On or about June 25, 2020, (Complete chronology will be attached as character limits were reached).
1 Affected Product
Vehicle
MAKE | MODEL | YEAR |
AUTOCAR | XPEDITOR | 2020 |
15 Associated Documents
Recall 573 Report – January 20, 2022
RCLRPT-21V930-1628.PDF 215.989KB
Recall 573 Report – December 10, 2021
RCLRPT-21V930-2714.PDF 215.9KB
Safety Bulletin
RCSB-21V930-5689.pdf 7685.575KB
Remedy Instructions and TSB
RCRIT-21V930-2923.pdf 7685.575KB
Miscellaneous Document – with NHTSA edits
RMISC-21V930-3032.pdf 40.603KB
Defect Notice 573 Report
RCLRPT-21V930-6589.PDF 214.379KB
Recall Acknowledgement
RCAK-21V930-7061.pdf 645.332KB
Miscellaneous Document
RMISC-21V930-0112.pdf 119.694KB
ISSUED Owner Notification Letter(Part 577)
RCONL-21V930-7729.pdf 158.768KB
Manufacturer Reimbursement Plan
RMRP-21V930-4271.pdf 613.304KB
Manufacturer Notices(to Dealers,etc)
RCMN-21V930-4788.pdf 106.265KB
Part 577 Owner Notification Envelope
RONE-21V930-1585.pdf 134.304KB
Recall Quarterly Report #1, 2022-1
RCLQRT-21V930-6171.PDF 211.14KB
Recall Quarterly Report #2, 2022-2
RCLQRT-21V930-5742.PDF 211.24KB
Recall Quarterly Report #3, 2022-3
RCLQRT-21V930-2012.PDF 211.324KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=21V930&docType=RCL
- 🍇➤Please Note: 1. The HD OBD option is available for heavy truck owners and the OBD/EOBD option is available for other vehicle. 2. Owners need to fix the problem with the truck first before they need clear the error code.
- 🍉➤【Support Full Systems for Heavy Duty Truck】 NL102 PLUS supports read and clear DTC, live data, ECU information for truck all systems. Including Engine, Transmission, Drivetrain, Suspension, ABS, ESP, Cluster, E-xhaust, P-articular, Suspension, Braking System, Cab Climate, Body Control, Instrument Panel, Fuel System and more, which are in compliance with J1939, J1708 and J1587 protocols, It includes almost American HD trucks(Class4-Class8), it is recommended that customers confirm before purchase that if they comply with the years and agreements supported by NL102P before purchasing.
- 🍋➤【Professional DPF Regeneration Tool】Force DPF Regen work on Cummings, Detroit, Maxxforce, ISUZU, HINO engine,It covers almost all US trucks, supported advanced features: DPF Regeneration,D-O-C Cleaning Procedures, DPF Regeneration in Parking, DPF Regeneration in Driving, DPF Onboard. NL102P's tool helps you re-awaken the engine power When the diesel p-articulates of the engine accumulate. It will save $800-$2500 for truck owners a year.
- 🍊➤【Excellent Oil Light Reset】NL102 PLUS support Oil service reset work on Cummings, Detroit, Maxxforce engine. when the replacement of engine oil is done, the truck system calculates when to change the engine oil and filter based on vehicle use. An oil change is required whenever indicated by the display, otherwise it will affect the engine maintenance and life. The NL102P truck scanner offers help to reset the Oil Life Reminder (Determine the Oil Service Light), ensure your driving safety.
- 🍐➤【All OBD/EOBD Diagnosis】NL102 PLUS supports both all 12V and all 24V truck, and it comes with 6 pin, 9 pin and 16 pin adapters for different interfaces. NL102 PLUS can read and earse the trouble codes, determine the MIL (check your Truck engine) and I/M Readiness, Freeze Frame, Live Data, O-xygen Sensor Test, On-Board Monitor, Vehicle Identification Info. Built in a DTC lookup library you can find the related code definition to help you determine if your car needs repair. In order to ensure that you can use the NL102P, please check the manual before purchasing.
- 🔥2024 TOP INTELLIGENT DIAGNOSTIC SCANNER FOR SEMI COMMERCIAL: ANCEL V5 HD obd2 scanner is specifically designed for 12V & 24V semi trucks,pickup trucks,heavy-duty trucks and 99% of commercial vehicles.you will enjoy✅All System Diagnostic;✅40+ Special Functions;✅ Full Bi-directional Test; ✅Advanced ECU Coding;✅Exclusive Remote Diagnosis Assistance;✅Full System Diagnostic ;✅Wider Vehicle Coverage;✅ Full HD OBD /OBDII /EOBD Modes;✅Top-level Hardware;✅>2 Yrs Free Update,Lifetime Tech Support
- 🚚40+ Resets with ABS SRS DPF Regen: ANCEL V5 HD includes 40+ resets for various systems, including ABS, SRS, DPF, EPB, BMS,DPF Regen, Injector Coding,Parameter Setting,Idle Speed Adjustment, Speed Limit Adjustment and more to fully meet your various needs. These resets can help reset the vehicle's systems to their default settings, eliminating any error codes or malfunctions that may be causing problems.Please send your VIN# to our 💌 amazon@anceltech.com 💌 to check compatibility.
- 🚛FULL BI-DIRECTIONAL CONTROL, GET YOU TO MALFUNCTIONS DIRECTLY:ANCEL V5 HD bidirectional scan tool supports bidirectional testing, which means it can both read and erase fault codes from the vehicle's ECUs.This feature saves time and money by eliminating the need for multiple scanners or tools.you can quickly identify whether the repair job works or not:Aftertreatment Test, Injector Test,Fuel Pump Test,Cylinder Test,Enigne State Monitor,A/C Compressor Test,Heated Oxygen Sensor Test and more.
- 🚜ADVANCED ECU CODING & PROGRAMMING:ANCEL V5 HD diesel truck scan tool comes with a powerful ECU programming and coding function, allowing you to reprogramme and decode the electronic control units (ECUs) of the vehicle.This feature is especially useful for technicians who need to update software,adjust parameters,or perform other modifications to the vehicle's electronic systems.🚦Note: ECU Coding is not universal to all cars, please check compatibility with VIN before order.
- 🚌OE-Level Full System Diagnostic:ANCEL V5 HD code reader is a professional-grade truck scanner that covers almost all the systems in semi-commercial vehicles, including engine, transmission, ABS, SRS, airbag,instrument panel, etc.It provides accurate and comprehensive diagnostic results,helping you quickly identify and solve vehicle problems,which are in compliance with J1939, 1708,ISO14230,ISO15765,ISO9141,ISO11898,E-J1850 VPW,SAE-J1850 PWM,J1587,CAN TP16,CAN TP20,AN-FD,and DOIP protocols.
- 🔥🔥🔥2024 New Functions Making X7 HD the Top Dog - Big Surprise!!! ANCEL X7 HD heavy duty truck scan tool 10 major functional advantages .✅>Full HDOBD/OBD2 Function ✅>ALL System Diagnostic ✅>40+ Reset Function ✅>Active Test / Bi-Directional Control✅>ECU Coding✅>Graphing Live Data✅>Wide Compatibility ✅>2 Yrs Free Update✅>Remote Operation✅>Bluetooth 5.0 & Wifi In addition, 8 major hardware advantages: ✅>6000 mAh✅>10.1 inch Tablet✅>2G RAM✅>32G ROM (Expandable to 128GB)✅>Data Record & Replay & Print✅>Android 10.0✅>Bluetooth 5.0 & Wifi✅>14 Languages
- 🚛Advanced ECU Coding & Programming - ANCEL X7 HD 10.1inch diesel truck scan tool is equipped with advanced ECU coding, supports Level calibration, Idle speed learning and Adjustment, Camshaft timing control learning, Control unit adaptations, Injector Codes, Read/Write VIN, Road speed limit optional vehicle speed set, etc... PLEASE NOTE that ECU codes are not compatible with all vehicles, please send us your VIN# to check vehicle compatibility.
- 🚛40+ Reset Functions & Bidirectional Control - 2024 newest top truck scanner diagnostic tool, comes with 40+ special services (ECU, Oil Reset, Injector Coding, EPB, ABS, SRS, Suspension, Throttle, etc. and always keep growing), which meet all your various needs for service and maintenance. Please send your VIN# to our 💌 amazon@anceltech.com 💌 to check compatibility.
- 🚛10 Inch All Systems Diesel Scanner & Full HDOBD/OBD2 Modes - ANCEL X7 HD diesel scanner diagnostic tool supports all systems scan, such as Engine, Brake, Retarder, TECU Transmission, Tachograph, ABS, SRS, TPMS, EPB, SAS, ESP, and other vehicle systems, comes with 10 obd2 service modes: read/erase error codes, Data Stream, I/M Readiness, Vehicle Information, Actuations, DTC Lookup, EVAP, view freeze frame, etc.
- 🚛OEM DPF Forced Regen & Cylinder Cutout Test & more - ANCEL X7 HD truck scanner not only supports DPF regeneration, DPF reset, DPF related information reset, DPR state reset, DPD forced regeneration etc, which helps you better solve the exhaust aftertreatment system problems, but also supports activate motor to do exhaust air in ABS Automatically. Moreover, it features TPMS activation, cylinder cut-off and learning functions.
- 🔎【Comprehensive Full Systems Diagnostic Tool For Truck】Launch Heavy Duty Truck Diagnostic Tool offers OE-Level diagnosis for all systems of heavy truck/Pickups/Bus/Van in compliance with OBD-II Communication Modes 1-10 and J1587, J1708 and J1939 protocols,Including Engine, Transmission, Drivetrain, Suspension, ABS, ESP, Cluster, E-xhaust, P-articular, Suspension, Braking System, Cab Climate, Body Control, Instrument Panel, Fuel System and more.
- 🔥【All OBD/EOBD Diagnosis】This truck scanner diagnostic tool supports both most 12V and 24V truck, and it comes with 6 pin, 9 pin and 16 pin adapters for different interfaces. Our truck scan tool can read codes, erase codes, I/M Readiness, Live data, EVAP Test. . . etc for obd2/eobd cars. Built in a DTC lookup library you can find the related code definition to help you determine if your car needs repair.
- 🚚【Wide Truck Applications】Heavy duty truck scan tool covers almost J1587, J1708 and J1939 protocols heavy duty trucks and OBD II vehicles. Such as Cummins, Paccar, Detroit, Perkins, International, Peterbilt, Allison, Eaton, Ford duty trucks and so on, Covers class 4 (14,001 lbs) through class 8 (33,000 lbs and over) heavy duty trucks. One that meets all the requirements! NOTE:Compatibility will vary on vehicles model and year, please send V-IN to check the compatibility before purchase.
- 💡【Friendly Design, Easy of Use】This heavy duty diagnostic scan tool is plug and play, simple and convenient, The excellent 2.8 inch LCD color screen makes it easy to view the displayed results and gives you a better overview of your car's problem areas and the identified codes. In addition, the processor is super-fast and responds without lagging, providing maximum comfort and efficiency in diagnostic and service work.
- ✨【3 YEARS WARRANTY & FREE LIFETIME UPDATES】The diesel truck scanner is exclusively designed for US truck. it's come With a full service functions and full systems and provides 24/7 technical support, 3 years warranty, 90-days free return for refund or replacement. This diesel scan tool is suitable for auto repair shops and technicians.No subscription fee and free lifetime updates.
- Powerful and Cost-Effective - An essential heavy duty truck scanner designed for heavy duty truck owner-operators and small commercial fleets. With the Diesel Decoder, just plug the diesel scan tool into the diagnostic port and pair with the free smartphone app to access in-depth HD diagnostic information.
- Swift and Adaptable - This heavy duty truck scanner recognizes both diagnostic trouble codes (DTCs) and brand-specific error codes for prevalent heavy-duty truck brands in North America, such as Freightliner, Peterbilt, Mack, Kenworth, Volvo, Western Star, among others and give the ability to perform DPF regens on select model years of Cummins, International, Detroit, Isuzu, Paccar, Mercedes, Hino and Mack/Volvo.
- Instant Repair Help - The diesel scan tool seamlessly connects to the Diesel Laptops comprehensive Diesel Repair Platform library so you can immediately start diagnosing and repairing any problems and get back on the road as soon as possible.
- Continuous Enhancement - Benefit from direct feature additions and updates via the app, our heavy duty truck scanner will continue to have functionality added over time. This removes the hassle of lengthy update processes and the financial strain of renewing costly diagnostic gear.
- 🌟【Run Your DPF Cleaner, Longer -Renew, Don't Replace!】Safeguard your truck from breakdowns and and high repair costs with focused DPF care. Opt for HD3400, featuring DPF regen, reset, DPR state control, and more, tailored for engines like Cummins, Detroit, Caterpillar, etc. Imagine this: easy and cost-effective DPF regen saving you from potential $10,000 to $30,000 in repairs. Unlock compliance-free operation for improved fuel efficiency, extended engine life, and significant cost savings
- 🚜【Maximize Caterpillar Engine Trucks' Potential!】HD3400 Plus diesel scanner, exclusively for Caterpillar engines (C7, C9, C11, C13, C15, C32, and more) commonly found in trucks like Caterpillar, Ford Pick-up, Freightliner, Peterbilt, Kenworth. Features include code reading/clearing, live data streaming, ECU retrieval, DPF regeneration and more. Unleash your Caterpillar engine's power!
- 🚛【Designed for Detroit Engine Trucks】ANCEL HD3400 heavy duty truck scan tool is compatible with a wide range of heavy duty commercial trucks – class 7 and class 8, medium duty trucks, light duty trucks and semi-trucks equipped with Detroit engines, including DD13, DD15, DD16, Series 50, Series 60, MBE 900, MBE 4000, OM501, OM502, DDDL 6, and DDDL 7.
- 🚐【Designed for Paccar Engine Trucks】ANCEL HD3400 heavy-duty truck scanner diagnostic tool is specifically designed for Paccar engines, including Paccar PX-7, PX-9, MX-11, MX-13. ❗Note: PACCAR engines post-2016 require a CAN-3 adapter for forced DPF regeneration. If you want to perform DPF regen for your PACCAR engines manufactured after 2016, please find us to get the additional CAN-3 adapter.
- 🌟【Unlock Advanced DPF Regeneration】Our diesel scanner diagnostic tool excels in DPF reset, providing active/forced regeneration and advanced DPF state control. Save time and money on DPF maintenance, making it the top choice for truck diagnostics. Elevate your DPF maintenance with our advanced features!
- 【Extensive Compatibility】After the upgrade, the compatibility is wider and more accurate! HD601 PRO heavy duty truck scanner supports all major truck models that comply with standard protocols (SAE J1939, SAE J1708, ISO 14230-4, ISO 15764-4 and ISO 9141-2, ISO 27145-4 and Euro6). Such as Cummins, Paccar, Detroit, Perkins, Freightliner, International, Peterbilt, Ford, Class 4-Class 8 trucks, etc. It also check engine diagnosis on most cars, minivans and light trucks from 1996 and latest.
- 【OE-Level Full System Diagnostic】HD601 PRO Diesel Scanner supports all system scans of heavy trucks compliant with standard protocols SAE J1939 & J1708, such as Engine, ABS, Transmission, Braking System, ESP, EPS, Fuel System, etc, It is a great scan tool for Cummins, Caterpillar, Detroit, Perkins, Maxxforce, BendixWabash, Wabaco, Haldex, Allison, Eaton heavy trucks, With this truck tool, you can get deep analysis data about the system and do some repairs by yourself, saving much time and money.
- 【Enhanced Diesel OBD Scanner】As a 2-in-1 code reader, it supports the latest ISO27145 and Euro6 protocols and enables diagnosis of car and truck engines. In addition to reading codes, clearing codes and displaying live data in a text or graphic format for trucks, you can also retrieve vehicle information, view freeze frames and look up DTCs. To ensure that this device works with different engines, it is also equipped with 6, 9 and 16 pin cables that allow you to easily turn off the CEL light.
- 【DTC Library】+【Life Time Free Update】The built-in DTC library allows you to retrieve the codes directly without searching for the definition in the book. Whether you are a professional mechanic or a DIY car owner, HD601 diesel scanner explains the existing problem, makes it easier for you to understand the codes definition and fix the problem faster. Plus, you get a lifetime free internet updates, so you always have the latest software for diagnostics in English and Spanish languages.
- 【Friendly Design, Easy of Use】This scanner is plug and play, simple and convenient, and very friendly for beginners. With improved buttons for easy menu navigation. The excellent 2.8 inch LCD color screen makes it easy to view the displayed results and gives you a better overview of your car's problem areas and the identified codes. In addition, the processor is super-fast and responds without lagging, providing maximum comfort and efficiency in diagnostic and service work.
- 【2024 NEWEST LAUNCH 1st Advanced Scan Tool Compatible With 12V&24V Vehicles】Design for Passenger&Commercial Vehicles 2 in1,work for Cars/Trucks/buses/trailers/excavators/diesel engine/pick-up/etc.
- 【J2534 Reprogramming with Smartlink C】Advanced OEM J2534 reprogramming,Helps access direct data online, replace existing software/firmware in ECU,program new ECUs and fix software-controlled issue.
- 【Over 60 Service Reset Functions + Bi-Directional + ECU Coding 】This scan tool can support ECU Coding,60+ reset service functions like SAS/EPB/TPMS/DPF/Oil/Brake/ABS Bleed, Injector coding, etc.
- 【2024 BEST Advanced Hardware & All Systems Diagnosis+Topology Display 】Support All systems Diagnostic including ENG, AT, ECM, TCM, ABS, SRS, BCM, BMS, TPMS, SAS, Fuel System, Light System and more.
- 【Wider Vehicle Coverage of 12V & 24V Vehicles + 24 Languages】LAUNCH X431 PRO3S+SMARTLINK HD automotive scanner is ALL-IN-ONE Scan Tool for 12V cars and 24V Heavy-duty trucks support CANFD & DOIP.
- 【Full Systems Heavy Duty Scanner Tool】:this heavy duty scanner tool supports Read DTC and Clear DTC, Live Data,Engine Check, Transmission, Drivetrain, Suspension, Cluster, Suspension, Braking System, Cab Climate, Body Control, Instrument Panel, Fuel System and more, which are in compliance with J1939, J1708 and J1587 protocols,
- 【OBD2/HDOBD/EOBD All Diagnosis】: supports both all 12V and all 24V truck, with 6 pin and 9 pin adapters for different interfaces.It support reading code, earsing trouble codes, Live Data, determine the MIL (check your Truck engine) and I/M Readiness, Freeze Frame, O2 Sensor Test, On-board Monitor, Vehicle Identification Info.It can lookup DTC, translates the related code's meaning to help you know what's wrong with the car.
- 【Suitable for Most Trucks】:diesel diagnostic scanner support all truck standard protocols SAEJ1939/ J1587/ J1708,it work on heavy duty trucks/ light truck/ mini vans/ buses/ pickups from1996 to now.
- 【CANBUS System】:Detect the CANBUS node, and easily find out the wrong modoles and lines.
- 【Professional Automotive Scanner Diagnostic Tools】:Designed specifically for HDOBD/OBD2/EOBD.This HD10 covers all the functions of HDOBD,OBD2,and EOBD. What is more important is that it provide the results correctly and quickly, and you can read the results with graghs, which make you easier to read.
- 👍【2024 Newest wide Coverage for Heavy truck】: With support for standard HD OBD protocols and customized protocols, ANCEL HD3400 PRO provides 98% coverage for heavy truck models in the US market, including those with Cummins, Detroit, Caterpillar, Paccar engines,and trucks like Ford, Autocar, western star, Freightliner, Kenworth, Peterbilt, caterpillar,Terex, Thomas, Sany, Komatsu, Agrifac , Isuzu, Fuso, Hino,Volvo and more.
- 🚛【Available for Cummins 】ANCEL HD3400 Pro is specifically designed to support a wide range of Cummins engines found in trucks like Ford, Volvo, Freightliner, Kenworth, and more, as well as Sany machinery, Agrifac vehicles, RVs, and more. Compatible with ISX, ISM, ISN, QSB, X12, ISB, ISC, ISD, ISG, ISK, ISL, X15, B6.7, L9, L9N, QSM11, and other popular models.
- 🚒【Available for Caterpillar】exclusively designed for Caterpillar engines (C7, C9, C11, C13, C15, C32, and more), you can perform top-notch diagnostics to keep your trucks running reliably. Compatible with popular truck models like Kenworth, Peterbilt, Freightliner, International, Mack, and Volvo.
- 🚛【Available for Paccar&Detroit】ANCEL HD3400 PRO is compatible with a wide range of engine types, including Detroit engines (Series 50, Series 55, Series 60, OM501, OM502, DD5, DD13, DD15, DD16,MBE 900, MBE 4000, DD8, DDDL 6, DDDL 7, CPC2, CPC02T, CPC04T, CPC302T and More) and Paccar engines(PX-7, PX-9, MX-11, MX-13 and more). like medium-duty or light-duty trucks, or even semi-trucks
- 🚒【Superb Lifetime Free Update,Best Bang For The Buck】ANCEL HD3400 PRO diesel code reader allow our customers get the latest version with free update via WIFI,With Lifetime Free Update,HD3400 PRO is way more valuable by comparing with the other OBD diagnosis,which can save hundreds of dollar for our customers!
Last update on 2024-04-11 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
4680 Pinson Valley Parkway, Birmingham, AL 35215 Office: 205.920.2499 Fax: 205.341.0375 General Recall Reimbursement Plan I. Introduction Pursuant to 49 U.S.C. 30120(d), 49 C.F.R. Parts 573 and 577, and other applicable requirements, Autocar, LLC and Autocar Industries, LLC (collectively “Autocar”) hereby provides the National Highway Traffic Safety Administration (“NHTSA”) its general reimbursement plan for the cost of remedies paid for by vehicle owners before they are notified of a related safety recall. As set forth at 49 C.F.R. 573.6(c)(8)(i) and 49 C.F.R 573.13, the following information sets forth Autocar’s general plan to reimburse owners and purchasers for costs incurred for remedies in advance of notification of potential safety-related defects or noncompliance. II. Reimbursement Notification Autocar’s notice to a vehicle owner in accordance with 49 C.F.R. Part 577 will indicate whether Autocar is offering a refund. A vehicle owner will be eligible for reimbursement if the owner paid to have service to remedy the defect or noncompliance prior to a specified ending date. As set forth at 49 C.F.R 573.13(c)(2), the ending date shall be 10 calendar days after the date on which Autocar mailed the last of its Part 577 notifications to owners in the United States, unless a specific reimbursement plan is made available for a particular recall. Autocar’s notice will instruct owners to seek eligible reimbursement through Autocar’s Service & Warranties Department, at the following address or otherwise applicable business address: Autocar LLC Service & Warranties Department 551 S. Washington Street Hagerstown, Indiana 47346 Owners will also be instructed that they may contact Autocar by telephone (toll free) at 888-218-3611 or 877-973-3486 NHTSA’s regulations (see 49 C.F.R. 573.13(c)) permit Autocar to identify a beginning date for reimbursement eligibility. Accordingly, an owner who paid to remedy the defect or noncompliance prior to the identified beginning date would not be eligible for reimbursement. Autocar puts its owners and customers first, and therefore, the company has generally has not firmly established such a beginning date for reimbursement eligibility, and as of the date of this policy, does not presently anticipate changing this general policy. Should Autocar determine (as NHTSA permits) that a beginning date is appropriate, Autocar will indicate that date in the specific reimbursement plan for that particular recall. As permitted by 49 C.F.R. 577.11(e), Autocar may not include a reimbursement notification when all vehicles are well within the warranty period, subject to approval by NHTSA. 4680 Pinson Valley Parkway, Birmingham, AL 35215 Office: 205.920.2499 Fax: 205.341.0375 III. Costs to be Reimbursed For vehicles, reimbursement will not be less than the lesser of: • The amount paid by the owner for the remedy that specifically addressed and was reasonably necessary to correct the defect or noncompliance that is the subject of the recall; or, • The costs of the part(s) for the remedy (to be no more than the manufacturer’s list retail price for authorized part(s)), plus associated labor at local labor rates, miscellaneous fees (such as disposal of waste), and taxes. For replacement equipment, reimbursement will be the amount paid by the owner for each replacement item (limited to the amount of the retail list price of each defective or noncompliant item that was replaced, plus taxes, where the brand or model purchased by the owner was different than the brand or model that was subject to the recall). If the item of motor vehicle equipment was repaired, the reimbursement provisions identified above for vehicles will apply. As set forth at 49 C.F.R. 573.13(d)(1), costs incurred by the owner within the period during which Autocar’s original or extended warranty would have provided for a free repair of the defect or noncompliance will not be eligible for reimbursement. IV. Entity Authorized to Provide Reimbursement Autocar will directly reimburse owners, unless a specific reimbursement plan is made available for a particular recall, and will encourage owners to pursue requests for reimbursement directly through its Service & Warranties Department to expedite reimbursement, as set forth above in Section II. In whatever manner the request for reimbursement is made, under this Plan or a specific reimbursement plan, the owner will be directed to submit the required documentation, upon which reimbursement eligibility will be determined. V. Required Documentation The reimbursement determination will depend upon the information provided by the owner. As set forth at 49 C.F.R. Part 573.13(d)(4), the owner must submit all of the following information: • Claimant’s name and mailing address; • For motor vehicles, the vehicle identification number (or “VIN”), vehicle make, model, and model year; • For replacement equipment, a description of such equipment or, for tires, the model and size; • Identification of the applicable recall (either Autocar’s recall number, or NHTSA’s applicable recall campaign number); • Identification of the owner of the recalled vehicle at the time that the pre-notification remedy was obtained; 4680 Pinson Valley Parkway, Birmingham, AL 35215 Office: 205.920.2499 Fax: 205.341.0375 • An original receipt for the pre-notification remedy that includes a breakdown of the amount for parts, labor, other costs and taxes, including costs for the replacement item. Where the receipt covers work other than to address the recall or noncompliance, Autocar may require the claimant to separately identify costs that are eligible for reimbursement. • If the remedy was obtained during the warranty period, documentation indicating that the warranty was not honored or that the warranty repair did not correct the problem related to the recall. Failure to submit all of the above information may result in denial of the reimbursement request. VI. Additional Information The Part 577 required owner notice will provide a toll-free telephone number through which specific information about the reimbursement plan can be requested from Autocar. As set forth at 49 C.F.R. 573.6, this general reimbursement plan will be incorporated into notifications by reference. Information specific to a particular recall also may be incorporated into the Part 573.6 notification. VII. Response to Requests for Reimbursement Autocar will act upon requests for reimbursement as follows: • Autocar will act upon a claim for reimbursement within 60 days of its receipt. If Autocar denies the claim, Autocar will send a notice to the claimant within 60 days of receipt of the claim that includes a clear, concise statement of the reasons for the denial. • If a claim for reimbursement is incomplete when originally submitted, Autocar will advise the claimant within 60 days of receipt of the claim of the documentation that is needed and offer an opportunity to resubmit the claim with complete documentation. Reimbursement shall be in the form of a check from Autocar. VIII. Miscellaneous Autocar will make a copy of this plan available to the public, upon request. As permitted by 49 C.F.R. 573.13(m), Autocar will not reimburse owners for recalls based solely on noncompliant or defective labels. As set forth at 49 C.F.R. 573.13(n), reimbursement for a pre-notification remedy will not be provided to an owner if, in the case of a motor vehicle or replacement equipment other than a tire, it was bought by the first purchaser more than 15 calendar years before notice is given under 49 U.S.C. 30118(c) or an order is issued under section 49 U.S.C. 30118(b). In the case of a tire, this period shall be 5 calendar years. Dated: June 1, 2020
**************************************************************************************************************
Page 1 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 ATTENTION: Service Managers / Parts Managers. SUBJECT: Autocar, LLC has determined that a defect regarding a potential stall/hesitation may exist on certain Xpeditor® vehicles during launch, when operated from the right-side stand-up position with the hydraulic system engaged. SAFETY RECALL INFORMATION: This document provides work instructions to install a Hill Start Aid system. VEHICLES AFFECTED: There are 46, 2019-2020 model year Xpeditor® chassis manufactured between June 7, 2018 and November 25, 2019 with non-sequential serial numbers in the range of 228128 through 232658. To determine if a vehicle is affected by this Recall, log in to the Autocar Warranty Management System at www.autocartruck.com. From the main menu, select “View Recalls/ Service Programs” and look for the Autocar Recall number above. An excel file will be accessible with the VIN list of affected vehicles. Alternatively, to determine if a single vehicle is affected, select “VIN Profile” from the main menu in the Autocar Warranty Management System. In the “Chassis Number” field, enter the last 6 of the VIN. Once the VIN profile is displayed, scroll down to the “Recall/Service Program Information” section to determine if the Recall is open. SERVICE RESPONSIBILITY: Service sites must perform this Recall on affected vehicles at no charge to the owner regardless of vehicle mileage, age, or ownership. If a vehicle affected by this Recall is taken into or is currently in your vehicle inventory, or at your center for service, you must perform this Recall before the vehicle is sold or released to the owner. Page 2 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 REQUIRED PARTS: (1) S7442003K002 Service kit (1) 3083117 Bulkhead coupler (1) 8096211 PRV (1) A7441052-001 AT-3 solenoid (1) 80” GZ170005-138 3/8 Green air line (2) 10” GZ170005-338 3/8 Red air line (3) GZ200041-064 3/8” X 1/4” 90 degree fitting (1) GZ200041-062 3/8” X 1/8” 90 degree fitting (1) GZ200042-064 3/8” X 1/4” 45 degree fitting (1) GZ200095-066 Y union fitting (1) S7440003-001 Bracket (1) S7440004K001 Hardware kit (14) 980464 Cable tie (4) FE286225BW01 1/4” locknut (2) FE286250BW01 1/2” locknut (4) FE410125AW22 1/4” bolt (2) FE410150AW14 1/2” bolt (1) S7470002-002 Harness HSA Paste or liquid pipe thread sealant, obtained locally. CLAIM CODING INFORMATION: Repair Number (Op Code) Time Allowance (SRT) Description 59301-0-19 3.0 HR Hill Start Aid Page 3 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 SAFETY NOTICES: Allow the vehicle’s engine and cooling system to cool to ambient temperature before performing the repair procedure. A hot engine or cooling assembly may cause burns or other personal injury. Never rely on the hydraulic pressure to hold the cab in an open position. Always use the safety pin in the cab tilt lock tube to prevent serious personal injury or death. To prevent eye injury, always wear eye protection when performing vehicle maintenance, service or inspection. Before working on a vehicle, set the parking brake, place the transmission in neutral and block the wheels. Failure to do so can result in unexpected vehicle movement and can cause serious personal injury or death. Page 4 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 Working on CNG/LNG Trucks If you store or dispense Compressed Natural Gas (CNG) or Liquefied Natural Gas (LNG), or if you work on CNG or LNG trucks, your location must be fully compliant with applicable codes, regulations and standards, including National Fire Protection Associate (NFPA) codes, Society of Automotive Engineers (SAE) standards, American National Standards Institute (ANSI) Natural Gas Vehicle (NGV) standards, the United States Code of Federal Regulations (CFR) and your state and local fire and other applicable codes (including, for example, the California Code of Regulations and the Texas Administrative Code). Contact your local fire department for guidance and additional compliance information. Technicians working on Autocar trucks with CNG or LNG engines must be trained in the proper repair of CNG and LNG trucks and engines and the safe storage and dispensing of CNG and LNG. Working on CNG Fuel Systems CNG fuel systems include a high pressure (3600 psi) system for fuel storage and a low pressure system (125 psi) for consumption by the engine. Understanding the characteristics of CNG and how the fuel system works will prevent injury and damage to persons and property. Attempting to operate or maintain any CNG fuel system without proper training is dangerous. Complete training and consult instructional bulletins from the CNG system suppliers, such as Agility Fuel Systems’ Field Service Bulletin, Safely Working on CNG Fuel Systems. Welding and Hot Work Near CNG and LNG Trucks Welding, grinding, and other “hot work” can be safely performed on or near a CNG or LNG vehicle, but certain precautions must be followed. Understand and perform the necessary precautions provided by the CNG system suppliers, such as Agility Fuel Systems’ Field Service Bulletin, Welding and Hot Work Precautions Near CNG and LNG Vehicles. Page 5 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 CNG Cylinders CNG fuel containers must meet Federal Motor Vehicle Safety Standard (FMVSS) 304 (Compressed Natural Gas Fuel Container Integrity) and/or ANSI/CSA NGV2 (Basic Requirements for Compressed Natural Gas Vehicle Fuel Containers). Both standards specify a detailed visual examination every three years. Truck owners are required to complete all necessary inspections, in accordance with the applicable standards and other resources, such as the Clean Vehicle Education Foundation and NGVAmerica’s Compressed Natural Gas (CNG) Container Visual Inspection Advisory. FMVSS 304 also requires that cylinders not be used after the end of life (EOL) date provided on the tank label. The EOL date is also displayed in the engine compartment and at the fueling connection of each truck. If there are any question as to proper decommissioning of a cylinder, contact the manufacturer, whose name and address is also required to be on the label. CNG Fuel Container Pressure Relief Devices (PRDs) PRDs must be properly maintained and positioned for safe operation of a CNG fuel system. Missing vent caps can allow moisture into PRDs and vent lines, which can freeze and damage these safety components. Debris which clogs the PRDs and/or vent lines can prevent proper function. PRDs must be positioned to vent upward, not outward, from a vehicle. Ensure that every truck owner completes periodic inspections of the PRDs and vent lines and systems, in accordance with guidance provided by the system component suppliers. Alert First Responders to CNG and LNG In the event of a fire or other emergency, alert first responders to the presence and location of CNG fuel systems, tanks and dispensers. Ensure that emergency personnel are aware of proper precautions, such as those provided in Agility’s First Responder Guide: CNG and LNG Vehicle Fuel Systems. Page 6 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 LOCKOUT/TAGOUT PROCEDURES: Before entering the vehicle or vehicle body, read and follow OSHA regulations concerning entry and working in “CONFINED SPACE” OSHA 1910.146 and “LOCKOUT/TAGOUT” OSHA 1910.147. Follow OSHA regulations while performing any work on the vehicle. The vehicle must be disabled by the following steps before performing any work on the vehicle: 1. Place the transmission in NEUTRAL. 2. Set the parking brake. 3. Shut the engine OFF. 4. Lock cab doors, keep the key in your pocket. Block the wheels before entering the body or performing any work on the vehicle. 5. Turn the battery disconnect switch OFF, if equipped. 6. Completely drain the air from the primary/A system and secondary/B system by opening the drain valves on the air tanks themselves or by using the drain manifold if supplied. When draining the air tanks, do not look into the area where air is draining. Dirt or sludge particles may be expelled in the air stream and can cause eye injury. 7. Place magnetic “DANGER” signs on both cab doors before entering the body or performing any work on the vehicle. 8. Take proper precautions before working under the vehicle. Use ramps approved for the weight of your vehicle, or use floor jacks and stands. Never work under a vehicle supported by jacks alone. Always use jack stands to support the vehicle. Page 7 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 Hill Start Aid (HSA) Installation Instructions. 1. Follow all lockout/tagout procedures and verify the battery disconnect switch is in the “OFF” position. If the unit is not equipped with a battery disconnect switch, disconnect the battery cables beginning with the negative cables, followed by the positive cables. 2. Locate the first cross member forward of the drive axle (see Figure 1 Detail “B”). Cross member location for ABS module See Detail “A” Cross member location for HSA Bracket See Detail “B” Cross member location for SBR See Detail “C” Figure 1 S7440003-001 Bracket Detail “A” ABS Module Detail “B” HSA Bracket Detail “C” SBR Page 8 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 3. Install the S7440003-001 bracket to the right side of the cross member using (2) FE286250BW01 1/2” locknut’s and (2) FE410150AW14 1/2” bolts and tighten to 90 lbs. ft. of torque (see Figures 2, 3 and 4). See Figures 3 and 4 Figure 2 Page 9 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 S7440003-001 Bracket S7470002-002 Harness HSA Figure 3 Page 10 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 F286250BW01 1/2” Locknut’s FE410150AW14 1/2” Bolts Tighten to 90 lbs. ft. of Torque Figure 4 Page 11 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 4. Install (3) GZ200041-064 3/8” X 1/4” 90 degree fittings, (1) GZ200041-062 3/8” X 1/8” 90 degree fitting and (1) GZ200042-064 3/8” X 1/4” 45 degree fitting. Apply paste or liquid pipe thread sealant to the exposed threads (obtained locally). Locate the 3083117 Bulkhead fitting, remove and discard the nut and lock washer. Apply paste or liquid pipe thread sealant to the exposed threads (obtained locally), install the 3083117 Bulkhead fitting and tighten to 15 lbs. ft. of torque (see Figure 5). 5. Using (4) FE286225BW01 1/4” locknut’s and (4) FE410125AW22 1/4” bolts, install the valve assembly to the S7440003-001 bracket (see Figure 5). Note: Verify orientation as indicated in Figure 5. FE286225BW01 1/4” Locknut’s FE410125AW22 1/4” Bolts FE286225BW01 1/4” Locknut’s FE410125AW22 1/4” Bolts GZ200041-064 3/8” X 1/4” 90 degree Fitting GZ200041-062 3/8” X 1/8” 90 degree Fitting A7441052-001 AT-3 Solenoid 3083117 Bulkhead Coupler GZ200041-064 3/8” X 1/4” 90 degree Fitting GZ200042-064 3/8” X 1/4” 45 degree Fitting 8096211 PRV GZ200041-064 3/8” X 1/4” 90 degree Fitting Remove and Discard Nut and Lock washer Figure 5 Page 12 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 6. Locate the Double Check Valve (DCV) behind the Service Brake Relay (SBR) on the right rearward side of the suspension cross member. Disconnect the service brake signal 3/8” green air line, at the Double Check Valve (DCV). Note: Verify the service brake signal line originates at the chassis manifold, port 1. The optional LWB signal line passes directly through the cab, bypassing the chassis manifold (see Figure 6, 7 and Detail “C”). Double Check Valve (DCV) Service Brake Relay (SBR) See Detail “C” Figure 6 Page 13 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 3/8” Green Air Line, Port 1 of Chassis Manifold Figure 7 Double Check Valve (DCV) Detail “C” Note: The Lever Work Brake (LWB) is optional. If the unit is not equipped with LWB, the DCV will not be present. For units without this option, use the line plumbed into the control port of SBR for step 6. Note: To verify the correct air line is selected at the DCV, disconnect the SBR signal from port 1 of the cab manifold and apply shop air. Page 14 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 7. Connect the service brake signal 3/8” green air line to the control port of the Hill Start Aid (HSA) solenoid (see Figure 8). 8. Install the GZ170005-138 3/8” green air line, connect the delivery port of the HSA solenoid to the DCV (disconnected in Step 6) (see Figure 8). 9. Locate the 3/8” red park brake signal line at the Park Brake Relay (PBR). Cut the 3/8” red park brake signal line near the PBR and install the GZ200095-066 Y Union. Install the GZ170005-338 3/8” red air line Into the open port of the Y union and connect to the supply port of the Pressure Reducing Valve (PRV) (see Figure 8). 10. Install the GZ170005-338 3/8” red air line into the delivery port of the PRV. Install the GZ170005-338 3/8” red air line into to the supply port of the HSA solenoid (see Figure 8). Figure 8, Rear Brakes Chambers 1. Primary (A Tank) 2. Secondary (B Tank) 3. Foot Valve 4. Pressure Reducing Valve (PRV) 5. Hill Start Aid Solenoid (HSA) 6. Service Brake Relay (SBR) 7. Park Brake Relay (PBR) 8. Rear Brake Chambers Page 15 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 11. Locate the ABS module and disconnect the X3 connector (see Figure 9). Figure 9 12. Remove and discard two plugs from the X3 connector, cavity 8 and 14. Install the S7470002-002 Harness HSA, wire number 783 into cavity 8 and wire number 784 into cavity 14 of the X3 connector and reinstall the X3 connector into the ABS module (see Figure 10). Figure 10, ABS X3 Connector Page 16 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 13. Install the S7470002-002 Harness HSA into the right frame rail following proper routing and clipping techniques and connect to the HSA Solenoid (see Figure 3). 14. Secure any harnesses that were displaced during the repair process and confirm that no chafing or rubbing can occur. Re-connect any air lines, other plumbing or electrical items that were disconnected. Turn on the battery disconnect switch or re-connect all battery terminals beginning with the positive connections, followed by the negative connections. 15. Start the truck and fully charge the air system. Shut off the engine and using soapy water, check for any air leaks at new plumbing connections. Page 17 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 This Section Contains Instructions for Testing the Parking Brake System. Note: Steps 16 through 20 are verifying the “A” system and Steps 24 through 27 are verifying the “B” system. 16. Start the engine to charge the air system fully to governor cut-out and shut the engine off. 17. Push the yellow Parking Brake button to confirm that it will not remain depressed or release the parking brake (see Figure 11). Figure 11 Note: The yellow Parking Brake button should return to the out or parking brake applied position. 18. While firmly pressing the service brake pedal, push the yellow Parking Brake button. Note: The yellow Parking Brake button should remain depressed or in the parking brake released position. Page 18 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 19. Drain the “A” (primary) system. Note: The yellow Parking Brake button should remain depressed or in the parking brake released position. 20. Drain the “B” (secondary) system. Note: The yellow Parking Brake button should pop out, applying the parking brake automatically at 40psi +/- 3psi. 21. Start the engine to charge the air system fully to governor cut-out and shut the engine off. 22. While firmly pressing the service brake pedal, push the yellow Parking Brake button. Note: The yellow Parking Brake button should remain depressed or in the parking brake released position. 23. Drain the “B” (secondary) system. Note: The yellow Parking Brake button should remain depressed or in the parking brake released position. 24. Drain the “A” (primary) system. Note: The yellow Parking Brake button should pop out, applying the parking brake automatically at 40psi +/-3psi. Note: If any portion of the functional test fails, please contact Autocar technical support at 888- 218-3611. 25. The parking brake inspection is complete. Page 19 of 20 January, 2022 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 This Section Contains Instructions for Testing the Lever Work Brake System. Lever Work Brake (LWB) Figure 12, Lever Work Brake Location 26. Start the engine to charge the air system fully to governor cut-out. 27. With the brake pedal applied, put the transmission in gear. With the brake pedal still applied, engage the Lever Work Brake (LWB). Once engaged the transmission will go into neutral. 28. Step on the brake pedal and release the LWB. The transmission will go back into gear automatically. If you fail to step on the brake pedal first, the transmission will remain in neutral. Page 20 of 20 SAFETY RECALL BULLETIN NHTSA RECALL 21V930 AUTOCAR, LLC SAFETY RECALL ACX-2107 January, 2022 Autocar, LLC 4680 Pinson Valley Parkway Center Point, AL 35215 888-218-3611 29. The Lever Work Brake test is complete. Note: If any portion of the Lever Work Brake test fails, please contact Autocar technical support at 888-218-3611. 30. Log in to the Autocar Warranty Management System at www.autocartruck.com. From the main menu, select “View Recalls/Service Programs” and look for the Autocar Recall number above. A PAR file will be accessible. Alternatively, to determine if a single vehicle is affected, select “VIN Profile” from the main menu in the Autocar Warranty Management System. In the “Chassis Number” field, enter the last 6 of the VIN. Once the VIN profile is displayed, scroll down to the “Recall/Service Program Information” section and a PAR file will be accessible, download the PAR file to your computer. 31. Connect your computer to the diagnostic port located under the dash and using Bendix® VEPS software, upload the PAR file to the vehicle. Using Bendix® ACom® diagnostics, verify the functionality of the HSA solenoid by performing the component test. 32. Contact your local Allison Service Center, provide the Vehicle Identification Number and and request to have the hill hold interface enabled. 33. Road test the vehicle and verify function of the Hill Start Aid system. Note: During the road test, it may take up to 1 hour for the Hill Start Aid system to calibrate. If any portion of the functional tests fail or if you have questions regarding this Recall, please contact Autocar Technical Support at 888-218-3611. 34. Once all functional tests have passed, the Hill Start Aid installation is complete.
**************************************************************************************************************
551 South Washington Street, Hagerstown, IN 47346 Office: 765.489.5499 Fax: 765.489.5230 IMPORTANT SAFETY RECALL This notice applies to your vehicle(s) with the VIN(s) indicated on the enclosed owner response cards. AUTOCAR, LLC SAFETY RECALL ACX-2107 NHTSA RECALL NO. 21V930 Dear Autocar Truck Owner: January 2022 This notice is being sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Autocar, LLC has determined that a defect which relates to motor vehicle safety exists in 46, 2019 through 2020 model year Xpeditor chassis. These chassis were manufactured between June 7 , 2018, and November 25, 2019, with non-sequential serial numbers in the range of 228128 through 232658. Our records indicate that your vehicle was manufactured within this time period and may contain the defect described herein. MODELS AFFECTED: Autocar Xpeditor MY 2019-2020 COMPONENTS AFFECTED: A potential stall/hesitation during launch when operated from the right-side stand-up position with the hydraulic system engaged. SAFETY DEFECTS AND POTENTIAL RISKS: When operated from the right-side stand-up position with the hydraulic system engaged, the vehicle could experience a stall/hesitation during launch. If this occurs while operating on an incline, the vehicle could move rearward, increasing the risk of a crash, personal injury or property damage. REPAIR REQUIRED: A hill start aid system will be installed at no charge. TIME REQUIRED FOR THE REPAIR: The estimated labor time to repair your vehicle is 3 hours. WHAT YOU SHOULD DO: To have your vehicle repaired, contact your local authorized Autocar service site or email warranty@autocartruck.com. ACF 00002 Rev. 000 551 South Washington Street, Hagerstown, IN 47346 Office: 765.489.5499 Fax: 765.489.5230 PRIOR REPAIRS: If you have previously paid for repairs relating to this recall you may be entitled to recover the amount you paid for those repairs. Submit a copy of all documentation supporting your claim to Autocar at the address set forth below in the “Assistance” section. NOTICE REGARDING LEASED VEHICLES: If you are a Lessor (as defined below) of a vehicle that is affected by this notice, you are obligated under federal law to provide a copy of this Notice to the lessee of such vehicle within 10 days of your receipt of this Notice. Further, you must maintain a record, which identifies the lessee(s) to whom you send a copy of this Notice, the date you send the Notice and the VIN of the vehicle that you have leased to the lessee(s). For purposes of this Notice, the term “Lessor” means a person or entity that is the owner, as reflected on the vehicle’s title, of any five or more leased vehicles, as of the date of this Notice. OWNER RECALL RESPONSE CARD: The enclosed Owner Recall Response Card identifies your vehicle. Please complete this postage-paid card and return it to Autocar. If you do not own, have sold or have traded the vehicle identified on the card, please indicate that on the postage-paid card and return it to Autocar. ASSISTAN CE: If you need assistance with this recall, call our toll-free numbers below or write to Autocar at: Autocar, LLC Service & Warranty Departments 551 S. Washington St. Hagerstown, Indiana 47346 888-218-3611 (Toll Free) 877-973-3486 (Toll Free) You may also submit a complaint to: Administrator National Highway Traffic Safety Administration 1200 New Jersey Avenue SE Washington, DC 20590 or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 800-424-9153); or go to http://www.safercar.gov. We regret any inconvenience this recall may cause, but we hope you recognize Autocar’s concern for your safety and satisfaction with your vehicle. Sincerely, AUTOCAR, LLC ACF 00002 Rev. 000
**************************************************************************************************************
ACF 00002 Rev. 000 551 South Washington Street, Hagerstown, IN 47346 Office: 765.489.5499 Fax: 765.489.5230 IMPORTANT SAFETY RECALL AUTOCAR, LLC SAFETY RECALL ACX-2107 NHTSA RECALL NO. 21V930 January 2022 TO: U.S. Distributors Dealer Principals, Service Managers, Warranty Managers, Parts Managers This notice is being sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Autocar, LLC has determined that a defect, which relates to motor vehicle safety, exists in 46, 2019-2020 model year Xpeditor chassis manufactured between June 7, 2018, and November 25, 2019, with non-sequential serial numbers between 228128 and 232658, accordingly, a recall to address this issue is being initiated effective January 24, 2022. MODELS AFFECTED: Autocar Xpeditor MY 2019-2020 COMPONENTS AFFECTED: A potential stall/hesitation during launch when operated from the right-side stand-up position with the hydraulic system engaged. SAFETY DEFECTS AND POTENTIAL RISKS: When operated from the right-side stand-up position with the hydraulic system engaged, the vehicle could experience a stall/hesitation during launch. If this occurs while operating on an incline, the vehicle could move rearward, increasing the risk of a crash, personal injury or property damage. REPAIR REQUIRED: A hill start aid system will be installed.at no charge to the owner. REPAIR AVAILABLE: VIN profiles in the Autocar Warranty System will be updated to show the open recall on January 24, 2022 and a spreadsheet of the affected VINs will be available in the Warranty system. REMINDER: It is a violation of Federal law to sell or lease a vehicle covered by this recall notice unless the recall remedy has been completed. Substantial civil penalties apply to violations of this law. If you have any questions or concerns, please contact the Autocar Warranty Department at warranty@autocartruck.com. Sincerely, AUTOCAR, LLC
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 21V-930 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Autocar, LLC Submission Date : NOV 26, 2021 NHTSA Recall No. : 21V-930 Manufacturer Recall No. : ACX-2107 Manufacturer Information : Manufacturer Name : Autocar, LLC Address : 551 S WASHINGTON STREET HAGERSTOWN IN 47346 Company phone : 7654895499 Population : Number of potentially involved : 16 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2020-2020 Autocar Xpeditor Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : NR Descriptive Information : Certain Xpeditor units that were custom built for a specific customer and have been up-fitted with an aftermarket power take off (PTO) may experience a stall/hesitation condition during launch with the PTO engaged. Production Dates : NOV 19, 2019 – NOV 25, 2019 VIN Range 1 : Begin : 5VCACSCEXLC232643 End : 5VCACSCE1LC232658 Not sequential Description of Defect : Description of the Defect : A potential stall/hesitation during launch when operated from the right sidestand up position with the hydraulic system engaged. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : When operated from the right side stand up position with the hydraulic system engaged, the vehicle could experience a stall/hesitation during launch. If this occurs while operating on an incline, the vehicle could move rearward, increasing the risk of a crash, personal injury or property damage. Description of the Cause : A considerable amount of the available engine torque at idle is consumed by the hydraulic system function. The right side stand up driver position does not readily allow for brake modulation. Identification of Any Warning that can Occur : None. Involved Components : Part 573 Safety Recall Report 21V-930 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 1 : NR Component Description : NR Component Part Number : NR Supplier Identification : Component Manufacturer Name : NR Address : NR NR Country : NR Chronology : On or about February 5, 2020, Autocar received information regarding two CNG units and one diesel unit for certain vehicles that were custom built for one customer. The information provided indicated potential concerns in connection with a lack of acceleration. An internal corrective action was initiated to analyze the alleged condition. On or about February 6, 2020, additional information was added to the corrective action to additionally evaluate the sales order group of 48 units to the one customer, and Autocar’s field service team proceeded with its investigation. On or about February 12, 2020, the Autocar field service team preliminarily identified that the “Vehicle Accelerator Management” parameter was unexpectedly enabled on the diesel unit, and Autocar tentatively identified that the parameter had not been enabled by Autocar prior to first sale to the customer. When this feature was disabled, the reported concern was eliminated, and the customer returned the vehicle to service. Further analysis in or about mid-March 2020 confirmed Autocar’s February 2020 preliminary view that the accelerator management parameter was not enabled by Autocar. As a result, Autocar reasonably determined that this was an isolated incident. Autocar subsequently moved the diesel unit matter to a separate corrective action, and closed it as resolved. Between late March 2020 and June 2020, the COVID-19 global pandemic restricted Autocar’s reasonable ability to conduct its normal investigative process, including travel restrictions, mandatory shelter in place orders, and related government ordered restrictions. Despite these government ordered restrictions, Autocar was in full communication with the customer, and in good faith, Autocar did not reasonably assess the reported condition as an unreasonable risk to safety. On or about June 25, 2020, (Complete chronology will be attached as character limits were reached). Part 573 Safety Recall Report 21V-930 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Remedy : Description of Remedy Program : Autocar will voluntarily initiate an owner notification and recall of all affected vehicles. Autocar will distribute to owners of affected vehicles an Owner Notification Letter, which will describe the defect and provide instructions for scheduling the inspection/repair of the vehicle at no cost to the vehicle’s owner. The owner letter will instruct vehicle owners who have paid to have this condition remedied prior to this campaign to seek reimbursement pursuant to Autocar’s General Reimbursement Plan, on file with the agency pursuant to 49 C.F.R. 573.6(c)(8)(i) and 49 C.F.R 573.13. How Remedy Component Differs from Recalled Component : A hill start aid system will be installed at no charge. Identify How/When Recall Condition was Corrected in Production : The units involved were custom manufactured for one specific customer. Recall Schedule : Description of Recall Schedule : The dealer and customer notifications will begin January 27, 2022 and end January 25, 2022 Planned Dealer Notification Date : JAN 24, 2022 – JAN 25, 2022 Planned Owner Notification Date : JAN 24, 2022 – JAN 25, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 21V-930 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Autocar, LLC Submission Date : DEC 10, 2021 NHTSA Recall No. : 21V-930 Manufacturer Recall No. : ACX-2107 Manufacturer Information : Manufacturer Name : Autocar, LLC Address : 551 S WASHINGTON STREET HAGERSTOWN IN 47346 Company phone : 7654895499 Population : Number of potentially involved : 46 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2019-2020 Autocar Xpeditor Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : NR Descriptive Information : Certain Xpeditor units that were custom built for a specific customer and have been up-fitted with an aftermarket power take off (PTO) may experience a stall/hesitation condition during launch with the PTO engaged. Production Dates : JUN 07, 2018 – NOV 25, 2019 VIN Range 1 : Begin : 5VCACSCE9KC228128 End : 5VCACSCE1LC232658 ✔ Not sequential Description of Defect : Description of the Defect : A potential stall/hesitation during launch when operated from the right sidestand up position with the hydraulic system engaged. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : When operated from the right side stand up position with the hydraulic system engaged, the vehicle could experience a stall/hesitation during launch. If this occurs while operating on an incline, the vehicle could move rearward, increasing the risk of a crash, personal injury or property damage. Description of the Cause : A considerable amount of the available engine torque at idle is consumed by the hydraulic system function. The right side stand up driver position does not readily allow for brake modulation. Identification of Any Warning that can Occur : None. Involved Components : Part 573 Safety Recall Report 21V-930 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 1 : NR Component Description : NR Component Part Number : NR Supplier Identification : Component Manufacturer Name : NR Address : NR NR Country : NR Chronology : On or about February 5, 2020, Autocar received information regarding two CNG units and one diesel unit for certain vehicles that were custom built for one customer. The information provided indicated potential concerns in connection with a lack of acceleration. An internal corrective action was initiated to analyze the alleged condition. On or about February 6, 2020, additional information was added to the corrective action to additionally evaluate the sales order group of 48 units to the one customer, and Autocar’s field service team proceeded with its investigation. On or about February 12, 2020, the Autocar field service team preliminarily identified that the “Vehicle Accelerator Management” parameter was unexpectedly enabled on the diesel unit, and Autocar tentatively identified that the parameter had not been enabled by Autocar prior to first sale to the customer. When this feature was disabled, the reported concern was eliminated, and the customer returned the vehicle to service. Further analysis in or about mid-March 2020 confirmed Autocar’s February 2020 preliminary view that the accelerator management parameter was not enabled by Autocar. As a result, Autocar reasonably determined that this was an isolated incident. Autocar subsequently moved the diesel unit matter to a separate corrective action, and closed it as resolved. Between late March 2020 and June 2020, the COVID-19 global pandemic restricted Autocar’s reasonable ability to conduct its normal investigative process, including travel restrictions, mandatory shelter in place orders, and related government ordered restrictions. Despite these government ordered restrictions, Autocar was in full communication with the customer, and in good faith, Autocar did not reasonably assess the reported condition as an unreasonable risk to safety. On or about June 25, 2020, (Complete chronology will be attached as character limits were reached). Part 573 Safety Recall Report 21V-930 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Remedy : Description of Remedy Program : Autocar will voluntarily initiate an owner notification and recall of all affected vehicles. Autocar will distribute to owners of affected vehicles an Owner Notification Letter, which will describe the defect and provide instructions for scheduling the inspection/repair of the vehicle at no cost to the vehicle’s owner. The owner letter will instruct vehicle owners who have paid to have this condition remedied prior to this campaign to seek reimbursement pursuant to Autocar’s General Reimbursement Plan, on file with the agency pursuant to 49 C.F.R. 573.6(c)(8)(i) and 49 C.F.R 573.13. How Remedy Component Differs from Recalled Component : A hill start aid system will be installed at no charge. Identify How/When Recall Condition was Corrected in Production : The units involved were custom manufactured for one specific customer. Recall Schedule : Description of Recall Schedule : The dealer and customer notifications will begin January 27, 2022 and end January 25, 2022 Planned Dealer Notification Date : JAN 24, 2022 – JAN 25, 2022 Planned Owner Notification Date : JAN 24, 2022 – JAN 25, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 21V-930 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Autocar, LLC Submission Date : JAN 20, 2022 NHTSA Recall No. : 21V-930 Manufacturer Recall No. : ACX-2107 Manufacturer Information : Manufacturer Name : Autocar, LLC Address : 551 S WASHINGTON STREET HAGERSTOWN IN 47346 Company phone : 7654895499 Population : Number of potentially involved : 46 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2019-2020 Autocar Xpeditor Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : OTHER Power Train : NR Descriptive Information : Certain Xpeditor units that were custom built for a specific customer and have been up-fitted with an aftermarket power take off (PTO) may experience a stall/hesitation condition during launch with the PTO engaged. Production Dates : JUN 07, 2018 – NOV 25, 2019 VIN Range 1 : Begin : 5VCACSCE9KC228128 End : 5VCACSCE1LC232658 ✔ Not sequential Description of Defect : Description of the Defect : A potential stall/hesitation during launch when operated from the right sidestand up position with the hydraulic system engaged. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : When operated from the right side stand up position with the hydraulic system engaged, the vehicle could experience a stall/hesitation during launch. If this occurs while operating on an incline, the vehicle could move rearward, increasing the risk of a crash, personal injury or property damage. Description of the Cause : A considerable amount of the available engine torque at idle is consumed by the hydraulic system function. The right side stand up driver position does not readily allow for brake modulation. Identification of Any Warning that can Occur : None. Involved Components : Part 573 Safety Recall Report 21V-930 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 1 : Power Take Off Component Description : PTO Component Part Number : No specific part numbers are assigned. Supplier Identification : Component Manufacturer Name : Autocar LLC Address : 551 S Washington Street Hagerstown Indiana 47346 Country : United States Chronology : On or about February 5, 2020, Autocar received information regarding two CNG units and one diesel unit for certain vehicles that were custom built for one customer. The information provided indicated potential concerns in connection with a lack of acceleration. An internal corrective action was initiated to analyze the alleged condition. On or about February 6, 2020, additional information was added to the corrective action to additionally evaluate the sales order group of 48 units to the one customer, and Autocar’s field service team proceeded with its investigation. On or about February 12, 2020, the Autocar field service team preliminarily identified that the “Vehicle Accelerator Management” parameter was unexpectedly enabled on the diesel unit, and Autocar tentatively identified that the parameter had not been enabled by Autocar prior to first sale to the customer. When this feature was disabled, the reported concern was eliminated, and the customer returned the vehicle to service. Further analysis in or about mid-March 2020 confirmed Autocar’s February 2020 preliminary view that the accelerator management parameter was not enabled by Autocar. As a result, Autocar reasonably determined that this was an isolated incident. Autocar subsequently moved the diesel unit matter to a separate corrective action, and closed it as resolved. Between late March 2020 and June 2020, the COVID-19 global pandemic restricted Autocar’s reasonable ability to conduct its normal investigative process, including travel restrictions, mandatory shelter in place orders, and related government ordered restrictions. Despite these government ordered restrictions, Autocar was in full communication with the customer, and in good faith, Autocar did not reasonably assess the reported condition as an unreasonable risk to safety. On or about June 25, 2020, (Complete chronology will be attached as character limits were reached). Part 573 Safety Recall Report 21V-930 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Remedy : Description of Remedy Program : Autocar will voluntarily initiate an owner notification and recall of all affected vehicles. Autocar will distribute to owners of affected vehicles an Owner Notification Letter, which will describe the defect and provide instructions for scheduling the inspection/repair of the vehicle at no cost to the vehicle’s owner. The owner letter will instruct vehicle owners who have paid to have this condition remedied prior to this campaign to seek reimbursement pursuant to Autocar’s General Reimbursement Plan, on file with the agency pursuant to 49 C.F.R. 573.6(c)(8)(i) and 49 C.F.R 573.13. How Remedy Component Differs from Recalled Component : A hill start aid system will be installed at no charge. Identify How/When Recall Condition was Corrected in Production : The units involved were custom manufactured for one specific customer. Recall Schedule : Description of Recall Schedule : The dealer and customer notifications will begin January 27, 2022 and end January 25, 2022 Planned Dealer Notification Date : JAN 24, 2022 – JAN 25, 2022 Planned Owner Notification Date : JAN 24, 2022 – JAN 25, 2022 * NR – Not Reported
**************************************************************************************************************
SEOCONTENT-END