2021-2022 Forest River Puma Travel Trailers Wastewater Holding Tank Missing Ventilation Pipe

“This site contains affiliate links for which OEMDTC may be compensated”

October 8, 2021 NHTSA CAMPAIGN NUMBER: 21V784000

Wastewater Holding Tank Missing Ventilation Pipe

In the presence of an ignition source, a gas build up increases the risk of fire.

 

NHTSA Campaign Number: 21V784

Manufacturer Forest River, Inc.

Components STRUCTURE, EQUIPMENT

Potential Number of Units Affected 44

 

Summary

Forest River, Inc. (Forest River) is recalling certain 2021-2022 Puma travel trailers. The black wastewater-holding tank may be missing the ventilation pipe, allowing methane gas to build up.

 

Remedy

Dealers will properly vent the black wastewater-holding tank, free of charge. Owner notification letters were mailed October 22, 2021. Owners may contact Forest River Customer Service at 1-574-642-0606. Forest River’s number for this recall is 420-1425.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.

 


RECALL 21V784 REMEDY INSTRUCTIONS
Make(s): Puma

Model(s): PUT32BH2B

Model Year(s): 2021 & 2022

Repair Code: RC-632-03-00-004105 Allotted Time: 10.00 HRS.

Inspection Code: N/A

Allotted Time: N/A

Concern:

A second black wastewater-holding tank ventilation pipe was not installed in the vehicle.

Photo(s) Required: YES

Prior Authorization Required: YES

Part(s) Kit Number: 10-07-2021

Part(s) Return: N/A

 

Disconnect the vehicles’ battery Positive and Negative, disconnect any House battery(s) Positive and Negative, if equipped with a generator ensure it is off and lastly, ensure the vehicle is disconnected from shore power.  Block any tires/wheels to prevent the vehicle from rolling. Failure to do so may result in electrocution, fire or other personal injury, property damage and/or death.

 

STEP 1: LOCATE THE BATH WALL IN FIGURE 1;

 

STEP 2: REMOVE THE FOLLOWING:

  • BATH DOOR
  • BATH DOOR CASING
  • BATH DOOR TRIM

 

STEP 3: REMOVE THE WALL DÉCOR PANEL FACING THE BUNK ROOM, NOTATED IN FIGURE 1;

 

STEP 4: MEASURE FROM THE INSIDE OF THE PINE FORWARD 3” AND MARK THE BOTTOM PINE BOARD IN THE   VERY CENTER (FIGURE 2);

 

CAUTION: ENSURE PRIOR TO DRILLING THE HOLE – ENSURE YOU DO NOT DRILL A HOLE THAT WILL BE OUTSIDE OF THE WALL. DO NOT TEAR THE LINO.

 

STEP 5: USE A 2 ¼” HOLE SAW AND DRILL A HOLE THROUGH THE BOTTOM PINE BOARD IN THE WALL AND    YOU WILL FIND A FLOOR HOLE ALREADY PRESENT. DO NOT DAMAGE THE HOLDING TANK.

 

STEP 6: USE THE SAME MEASUREMENTS, MARK THE PINE BOARD THAT IS AGAINST THE CEILING WITH THE      SAME DIMENSIONS FROM THE FLOOR AND DRILL THE SAME 2 ¼” HOLE THROUGH THE CEILING    PANEL AND ROOF DECK;

 

STEP 7: SLIDE THE 8 FOOT BLACK PIPE UP THROUGH THE ROOF HOLE THAT WAS JUST DRILLED AND    CONNECT/GLUE TO THE FITTING INSTALLED ON THE HOLDING TANK. SECURE THE BLACK PIPE TO    THE WALL PINE WITH THE 18” ZIP TIE;

 

STEP 8: RE-INSTALLATION ORDER:

  • BATH WALL DÉCOR PANEL
  • BATH DOOR CASING
  • BATH DOOR TRIM
  • BATH DOOR
  • RE-TRIM AS NEEDED USING THE SUPPLIED BATT STRIPS

 

STEP 9: ON THE ROOF, CUT OFF THE BLACK PIPE, LEAVING 2” – 2 ½” OF BLACK PIPE ABOVE THE ROOF    MEMBRANE;

 

STEP 10: APPLY THE SUPPLIED PUTTY TAPE TO THE CIRCUMFERENCE OF THE VENT CAP SURFACE THAT     MATES TO THE ROOF AND SECURE TO THE ROOF WITH SUPPLIED SCREWS, COVERING THE BLACK PIPE;

 

STEP 11: APPLY THE SUPPLIED SELF-LEVELING SEALANT LIBERALLY TO THE ROOF CAP, COVERING THE     SCREW HEADS AND EDGES OF THE VENT CAP, ALLOW TO CURE;

 

STEP 12: CLEAN ALL WORK AREAS. CLAIM REPAIR CODE.

 


This Notice applies to your vehicle VIN listed above.

Dear Forest River Customer:

This notice is sent to you in accordance with the requirements of the Motor Vehicle Safety Act. This notice is also sent to
you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Forest River – Office of
Corporate Compliance (“OCC”) has decided that a defect, which relates to the motor vehicle safety, exists in certain 2021-
2022 Puma PUT32BH2B Travel Trailer Recreational Vehicles This is to inform you that your vehicle may contain a defect
that could affect the safety of a person.

 

WHAT IS THE DEFECT/NONCOMPLIANCE?

The black wastewater-holding tank has a hole drilled for ventilation through the roof of the vehicle; however, the
ventilation pipe was not installed in the vehicle. There is an exposed hole from the top of the black wastewater-holding
tank exposed to the interior of the underbelly.

 

EVALUATION OF THE RISK TO THE VEHICLE AND OPERATOR(S) RELATED TO THE RECALL.

Any type of spark may ignite the methane gas, which may result in a fire, property damage or personal injury.

 

WHAT IS FOREST RIVER AND OUR DEALERSHIPS GOING TO DO?

Forest River is notifying dealerships of the recall. You may have the recall corrected at any Forest River dealership.
However, it is preferable if you have your selling dealership perform the remedy. Forest River completely covers your cost
for the remedy; you will not receive any bill of sale for anything covered under the above recall number.

 

WHAT SHOULD YOU DO?

Please contact your dealer immediately and request a service appointment to schedule the free remedy to install the
ventilation pipe. The vehicle Owner is responsible for arranging to have the work completed. Please state you have been
notified by Forest River of having a recall in process for your vehicle and provide the recall number for the dealership. It is
also helpful to the dealership to have a copy of this letter when you take your vehicle in for the recall remedy.

You may also visit www.forestriverinc.com for dealer locations.

 

HOW LONG WILL THE REMEDY PROCESS TAKE?

The estimated time of repair is 10.0 hours. However, the dealership may need to keep your vehicle or schedule an
appointment with you for a later date to fit into their regular service schedule.

 

WHAT IF YOU HAVE PREVIOUSLY PAID FOR REPAIRS TO YOUR VEHICLE FOR THIS PARTICULAR CONDITION?

If you have already paid for a repair that is within the scope of this defect under recall, you still need to have this recall
inspected and/or performed to ensure the correct parts and procedures were utilized.

Additionally, you may be eligible for a refund of previously paid repairs. Refunds will only be provided for within the scope
of this defect under recall.

Please send the service invoice to the following address:

Puma
Forest River, Inc.
Attn: WARRANTY MANAGER
2551 Century Dr
Goshen, IN 46528

 


Chronology :

On 10/1/2021, during the second run of this model in production, Forest River’s manufacturing plant determined that they had not vented the black tank properly. They did not install the pipe that stems from the tank through the roof to allow for proper ventilation.

On 10/5/2021, the manufacturing plant and Forest River’s Office of Corporate Compliance were able to determine all vehicles’ affected.

On 10/8/2021, Forest River’s Corporate Recall Committee voted to recall.

 


2 Affected Products

Vehicle

MAKE MODEL YEAR
FOREST RIVER PUMA 2021-2022

 


8 Associated Documents

Manufacturer Notices(to Dealers,etc)

RCMN-21V784-0339.pdf 218.868KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [213.74 KB]

 


ISSUED Owner Notification Letter(Part 577)

RCONL-21V784-9410.pdf 209.005KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [204.11 KB]

 


Remedy Instructions and TSB

RCRIT-21V784-6948.pdf 422.984KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [413.07 KB]

 


Recall Quarterly Report #1, 2021-4

RCLQRT-21V784-3860.PDF 211.139KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.19 KB]

 


Defect Notice 573 Report

RCLRPT-21V784-8532.PDF 214.037KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.02 KB]

 


Recall Acknowledgement

RCAK-21V784-2028.pdf 645.801KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [630.67 KB]

 


Recall Quarterly Report #2, 2022-1

RCLQRT-21V784-7651.PDF 211.237KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.29 KB]

 


Recall Quarterly Report #3, 2022-2

RCLQRT-21V784-0265.PDF 211.318KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.37 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=21V784&docType=RCL

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
Bestseller No. 1
16 Gallon RV Fresh/Gray Water Tank 24" x 15" x 10" BPA Free (16 Gallon)
  • This 16 gallon water tank measures 24" x 15" x 10" (not including fittings)
  • These rotational molded fresh water tanks are made from a high quality durable polyethylene material.
  • One piece seamless construction - No Seams to burst
  • All tanks come with (1) 1.25" water fill inlet and (3) 3/8" NPT connections. Non-Pressurized Tank - The tank must be vented
  • Stain, corrosion and rust resistant features make them ideal for replacement or OEM installation on RVs, horse trailers or marine products.
Bestseller No. 2
Class A Customs | One (1) RV Fresh and Gray Water 30 Gallon Tank | T-3000
  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 34.5” Longest Length (not including fittings) x 12” x 17.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.: (TWO) 1.5" Balloon Style Threaded Female NPT Standard - fitting will be closed, to use remove inner membrane with razor knife (TWO) .5" Threaded Female NPT Standard - open fitting, unsealed
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 3
Class A Customs | T-4000 | One (1) RV Fresh Water 40 Gallon Tank, Grey Water
  • 40 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 39 1/2” Longest Length (not including fittings) x 13” x 18” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 4
Class A Customs | T-6500 | 65 Gallon RV Fresh Water Holding Tank
  • 65 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 44.5” Longest Length (not including fittings) x 17.5” x 19.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 5
Class A Customs | One (1) RV Fresh and Gray Water use 33 Gallon Tank | T-3300
  • 33 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 36” Longest Length (not including fittings) x 12” x 17.75” Average thickness 7/32” +/- (+/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 6
Class A Customs | T-7500 | 75 Gallon Fresh Water Holding Tank
  • 75 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 50.5” Longest Length (not including fittings) x 17.5” x 19.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 7
Class A Customs | 16 Gallon RV Concession Fresh and Gray Water Tank | T-1600
  • 16 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 26” Longest Length (not including fittings) x 9” x 16” ” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 8
Class A Customs | T-2000 | One (1) RV Fresh Water 20 Gallon Tank, Grey Water
  • 20 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 9
Class A Customs | 42 Gallon RV Concession Fresh and Gray Water Holding Tank | T-4200
  • 42 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (THREE) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 10
Class A Customs | 20 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2000-BPK-PUMP
  • 20 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose
  • classAcustoms 12 VOLT Fresh Water Pump MODEL # 12V3 - FRESH WATER USE ONLY - OPEN FLOW 11.6LPM / 3.0GPM AMPS 4.0A MAX AMPS 8.0A SHUT OFF PRESSURE 45PSI/3.1 Bar ON-DEMAND PUMP only turns on when senses pressure changes in line 12 VOLT POWER ONLY 110/115/220 volt will damage the unit - READ INSTRUCTION BOOKLER BEFORE INSTALLATION

Last update on 2024-04-15 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

 


Leave a Comment

Share to...