Incorrect GVWR on Certification Label/FMVSS 120 – 2021 Heartland Pioneer SS171 Travel Trailers

“This site contains affiliate links for which OEMDTC may be compensated”

June 28, 2021 NHTSA CAMPAIGN NUMBER: 21V491000

Incorrect GVWR on Certification Label/FMVSS 120

The operator may overload the vehicle, increasing the risk of a crash.

 

NHTSA Campaign Number: 21V491

Manufacturer Heartland Recreational Vehicles, LLC

Components EQUIPMENT

Potential Number of Units Affected 27

 

Summary

Heartland Recreational Vehicles, LLC (Heartland) is recalling certain 2021 Heartland Pioneer SS171 travel trailers. The Federal Certification label has the incorrect Gross Vehicle Weight Rating (GVWR) and axle rating. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 120, “Wheels and Rims – Other Than Passenger Cars” and 49 CFR Part 567, “Certification.”

 

Remedy

Heartland will mail replacement labels to owners, free of charge. Owner notification letters were mailed on August 9, 2021. Owners may contact Heartland customer service at 1-877-262-8032.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.

 


INFORMATION REDACTED PURSUANT TOTHE FREEDOM
OF INFORMATION ACT (FOIA), 5 U.S.C.552{8){6)

21v491 V.I.N. I TAG REPLACEMENT INSTRUCTIONS

 

IMPORTANT: DO NOT APPLY NEW LABELS OVER THE EXISTING LABELS.

1. Locate sections 1, 2 and 4 on the driver’s side of your unit, typically just above the baggage door. Remove sections 1, 2 and 4 from your sidewall using a plastic scraping tool being careful not to scratch your unit. You may use isopropanol alcohol to assist with adhesion removal if needed.

2. Locate sections 1, 2 and 4 in the new set you received in the mail, remove from backer and carefully place on side wall in the order you removed them.

3. Locate section 3 in the door jamb closest to the hinge of the entrance door. Remove section 3 from your door jamb using a plastic scraping tool, being careful not to scratch your unit. You may use isopropanol alcohol to assist with adhesion removal.

4. Remove section 3 from the backer and place on the inside of the door jamb.

 



1 Affected Product

Vehicle

MAKE MODEL YEAR
HEARTLAND PIONEER 2021

 


9 Associated Documents

Recall 573 Report – Amendment 2

RCLRPT-21V491-6993.PDF 214.256KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.23 KB]

 


Recall Acknowledgement

RCAK-21V491-2802.pdf 645.988KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [630.85 KB]

 


Recall 573 Report – Amendment 1

RCLRPT-21V491-9047.PDF 214.208KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.19 KB]

 


Noncompliance Notice 573 Report

RCLRPT-21V491-4923.PDF 214.18KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.16 KB]

 


ISSUED Owner Notification Letter(Part 577)

RCONL-21V491-6833.pdf 162.271KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [158.47 KB]

 


Manufacturer Notices(to Dealers,etc)

RCMN-21V491-9241.pdf 136.957KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [133.75 KB]

 


Recall Quarterly Report #2, 2021-4

RCLQRT-21V491-0271.PDF 211.236KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.29 KB]

 


Remedy Instructions and TSB

RCRIT-21V491-5703.pdf 382.166KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [373.21 KB]

 


Recall Quarterly Report #1, 2021-3

RCLQRT-21V491-7816.PDF 211.134KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.19 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=21V491&docType=RCL

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
Bestseller No. 1
The Trailer Parts Outlet - 3.5k TK Trailer Axle - 3500 lb Idler 5 Lug - Dexter Compatible, 61/46 Hubface/Spring Center - (4'0) Frame Width / 5x4.5 Bolt Pattern
  • Specs: 3,500 lbs Idler Trailer Axle (Capacity 3.5K), 5 Lug, Tube: 2 3/8"
  • High Strength Straight Steel Axle Tube
  • Axle comes fully assembled, so all you'll have to do is attach the springs, the U-bolt kits, and the tire and wheel assemblies.
  • Underslung - Spring seats are welded to the bottom of the axle, which allows for a lower ride height.
  • Trailer Axle Design for use on Light Duty Trailers
Bestseller No. 2
The Trailer Parts Outlet - 2k TK Trailer Axle - 2000 lb Idler, 61/46 Hubface/Spring Center - (4'0) Frame Width / 4x4 Bolt Pattern
  • EZ Lube Design Removable rubber plug on the hub cap with easy access to a grease-able zerk fitting Grease your axle without pulling off your whole entire hub
  • Internal Wiring System To ensure seamless design Protect brake wires from wear and tear
  • High Strength Straight Steel Axle Tube Construction to ensure Even Tire Wear A better highway experience
  • Underslung - Axle is welded with spring seats on the bottom Allows for lower ride height For optimal usage, use with double eye springs
Bestseller No. 3
LCI Lippert 3,500LB Straight Idler Trailer Axle 72HF 58SC
  • 72" from Hubface to Hubface and 58" Spring Center to Spring Center.
  • Springs are 25 1/4" long and 1 3/4" wide
  • 4 Leaf Springs
  • 2-3/8" Main Tube
  • 5 Lug with a 4 1/2" bolt pattern. 1/2 lug studs.
Bestseller No. 4
The Trailer Parts Outlet - 2k TK Trailer Axle - 2000 lb Idler, 71/58 Hubface/Spring Center - (5'0) Frame Width / 5x4.5 Bolt Pattern
  • Capacity: 2000 lbs, Tube:1-3/4 | 5x4.5 Bolt Pattern
  • EZ Lube Design: Removable rubber plug on the hub cap with easy access to a grease-able zerk fitting. Grease your axle without pulling off your whole entire hub.
  • Internal Wiring System: To ensure seamless design and protect brake wires from wear and tear.
  • High Strength Straight Steel Axle Tube Construction: To ensure even tire wear and a better highway experience.
  • Underslung - Axle is welded with spring seats on the bottom: Allows for lower ride height. For optimal usage, use with double eye springs.
Bestseller No. 5
TK Axles + 3.5k-3500 Lb Capacity Trailer Idler Straight Axle - 5 on 4.5 Bolt Pattern (Assembled Idler Axle, 73" Hubface-58 Spring Center(5'0Frame))
  • Completely DEXTER Compatible; Half the Price
  • Capacity: 3500 lbs
  • Option to Add Spring and Ubolt Kits Needed to Hang Your Axle
  • Tube: 2 3/8"; EZ Lube Design
  • Underslung: Axle is welded with Spring Seats on the Bottom
Bestseller No. 6
The Trailer Parts Outlet - 3.5k TK Trailer Axle - (3500 lb Beam Only), 95/80 Hubface/Spring Center - (6'10) Frame Width for Utility/ATV/Boat/Cargo
  • Versatile Design - Compatible for use on Medium Duty Trailers Utility, Boat, Car Haulers, ATV, Lawn & Landscape, Flatbed, Livestock, Cargo, Enclosed, RV Trailers, Dump, Lowboy, Flatbed Trailers and more
  • EZ Lube design for effortless maintenance - grease your axle without removing the whole hub assembly
  • Underslung - Our trailer axle beam is welded with spring seats on the bottom Allows for lower ride height, for optimal usage, use with double eye springs
  • High-Strength Construction - Made with straight steel axle tube to ensure even tire wear and a better highway experience
  • Easy Installation - Simply pair with double eye springs for optimal usage and get your trailer back on the road in no time
Bestseller No. 7
The Trailer Parts Outlet - 3.5k TK Trailer Axle - 3500 lb Idler 5 Lug - Dexter Compatible, 89/74 Hubface/Spring Center - (6'4) Frame Width / 5x5 Bolt Pattern
  • Specs: 3,500 lbs Idler Trailer Axle (Capacity 3.5K), 5 Lug, Tube: 2 3/8"
  • High Strength Straight Steel Axle Tube
  • Axle comes fully assembled, so all you'll have to do is attach the springs, the U-bolt kits, and the tire and wheel assemblies.
  • Underslung - Spring seats are welded to the bottom of the axle, which allows for a lower ride height.
  • Trailer Axle Design for use on Light Duty Trailers
Bestseller No. 8
RIGID HITCH INCORPORATED 2,000 lb. Torsional Stub Axles with 5-Bolt on 4-1/2 Inch Hubs (TSA-20150)
  • 2,000 lbs capacity
  • Stub axles can be bolted (hardware not included) or welded to trailer frame
  • 45 degree downward starting angle
  • Perfect item to easily build your own custom motorcycle trailer
  • Read product description below for more detailed information.
Bestseller No. 9
The Trailer Parts Outlet - 6k TK Trailer Axle - 6000 lb Idler 6 Lug, 85/70 Hubface/Spring Center - (6'0) Frame Width / 6x5.5 Bolt Pattern
  • 6,000 lbs TK Trailer Axle (6K Capacity), Tube: 3", Bolt Pattern: 6x5.5
  • Axles come fully assembled - Packed with High-Temp Axle Grease
  • High Strength Steel Axle Tube Construction to ensure
  • Designed for use on Light Duty Trailers
Bestseller No. 10
LCI Lippert 3,500LB Straight Idler Trailer Axle 60HF 48SC
  • 60" from Hubface to Hubface and 48" Spring Center to Spring Center.
  • Springs are 25 1/4" long and 1 3/4" wide.
  • 4 Leaf Springs
  • 2-3/8" Main Tube
  • 5 Lug with a 4 1/2" bolt pattern. 1/2 lug studs.

Last update on 2024-04-12 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...