“This site contains affiliate links for which OEMDTC may be compensated” |
April 22, 2021 NHTSA CAMPAIGN NUMBER: 21V284000
Check Valve Retainer Not Properly Seated/FMVSS 121
Unintended spring brake application may occur, increasing the risk of a crash.
NHTSA Campaign Number: 21V284
Manufacturer Blue Bird Body Company
Components SERVICE BRAKES, AIR
Potential Number of Units Affected 1,634
Summary
Blue Bird Body Company (Blue Bird) is recalling certain 2020-2022 Vision and All American school buses. A retainer was not properly seated in the SC-3 single check valve and may not provide source air isolation when pressure is applied. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, “Air Brake System.”
Remedy
Dealers will replace the SC-3 check valves, free of charge. Owner notification letters are expected to be mailed June 18, 2021. Owners may contact Blue Bird customer service at 1-478-822-2242. Blue Bird’s number for this recall is R21BE-SB.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
RECALL
R21BE – BENDIX® SC-3™ SINGLE CHECK VALVE
Models Affected: Certain Model Year 2020 Electric (EV) Buses and Certain Model Year 2022 Vision and All American Buses Equipped with Bendix® Air Brakes
Issue: Bendix Commercial Vehicle Systems LLC is conducting a voluntary safety recall campaign, Bendix Recall No.: 21E-015, involving the Bendix® SC-3™ single check valve (Bendix Part Number K096210) (Blue Bird Part Number 10034984)
Corrective Action: Inspect And Replace If Required Bendix Part Number K096210, Blue Bird Part Number 10034984
Parts/Tools Needed:
Item Number | Part Number | Description | Quantity |
1 | 10034984 | Bendix® SC-3™ Single Check Valve (Bendix Part Number K096210) | 1 (IF REQUIRED) |
1 | Source Local | Liquid Thread Sealant | 1 (IF REQUIRED) |
1 | Source Local | 15/16 Inch Open End Wrench | 1 (IF REQUIRED) |
1 | Source Local | 1/2 Inch Open End Wrench | 1 (IF REQUIRED) |
WARNING: Always follow all Federal, State, Local, and Shop safety standards and use proper safety equipment, and thoroughly read and understand all instructions before performing these procedures. Park bus on level surface, apply parking brake, turn off ignition key, and Chock Wheels. CRITICAL: Block and hold the vehicle by means other than the air brakes. Ensure that the bus is secured from any possible movement.
Instructions:
- The Bendix® SC-3™ single check valve is installed on the Bendix® SR-7® spring brake modulating valve on Blue Bird buses equipped with air brakes. The physical mounting location varies based on optional features ordered and the Blue Bird bus model being inspected, and repaired. Blue Bird R21BE Instructions and a Bendix Service Data Manual SD_03_2205_US_006 are both attached to this R21BE You can view or print both by clicking on the attachment desired.
- Additional information related to Bendix Recall ; 21E-015 can also be found on the Bendix website. See Bendix website links below.
BW8136 – Identifying Bendix SC-3 Single Check Valves Covered in this Field Action
TCH-003-059 – Bendix SC-3 Single Check Valve Recall
Bendix SC-3 Single Check Valve Replacement Video
Action Required For Identifying the Recalled Bendix® SC-3™ Single Check Valve
Identifying Bendix® SC-3™ Single Check Valves Covered in this Field Action
Blue Bird Vehicles
A potentially defective SC-3 single check valve on a Blue Bird vehicle has no date code identifier. Blue Bird purchased SC-3 single check valves from Bendix as standalone parts and not as part of an assembly. To identify a potentially defective SC-3 single check valve on a Blue Bird vehicle, perform the following steps:
1. Remove the SC-3 single check valve from the Bendix®SR-7® spring brake modulating valve.
2. See Figures 1 and 2. Inspect the SC-3 single check valve If the retainer is fully seated, it is correctly installed and not affected by this recall campaign. If the retainer is not fully seated, or is missing, damaged, or the shuttle or retainer are missing or fractured, the SC-3 single check valve falls within the recall parameters. The SC-3 single check valve needs to be replaced. If the shuttle or the retainer are missing (not located in the SC-3 fitting nor in the supply port of the SR-7 spring brake modulating valve) or fractured, the SR-7 spring brake modulating valve will need to be replaced as well.
Navistar®, New Flyer, and Oshkosh Vehicles
NOTE: Any publication from the OEM supersedes the below information.
A potentially defective SC-3 single check valve on a Navistar, New Flyer, or Oshkosh vehicle was purchased from Bendix as an assembly including the SC-3 single check valve and the SR-7 spring brake modulating valve. To identify a potentially defective SC-3 single check valve on a Navistar, New Flyer, or Oshkosh vehicle, perform the following steps:
1. Remove the SC-3 single check valve from the SR-7 spring brake modulating valve.
Figure 1 – SC-3 Single Check Valve Retainer
Figure 2 – SC-3 Single Check Valve Internal Components – Spring and Shuttle
2. See Figures 1 and 2. Inspect the Bendix® SC-3™ single check valve retainer. If the retainer is fully seated, it is correctly installed and not affected by this recall campaign. If the retainer is not fully seated, or is missing, damaged, or the shuttle or the retainer are missing or fractured, the SC-3 single check valve falls within the recall The SC-3 single check valve needs to be replaced. If the shuttle or the retainer are missing (not located in the SC-3 fitting nor in the supply port of the Bendix® SR-7® spring brake modulating valve) or fractured, the SR-7 spring brake modulating valve will need to be replaced as well.
OR
1. See Figure 3. A potentially defective SC-3 single check valve that was purchased as part of an assembly with an SR-7 spring brake modulating valve can be identified by the date code on the SR-7 spring brake modulating If the SR-7 spring brake modulating valve has a date code that is any date between, and inclusive of, 7/27/20 and 9/29/20, the SC-3 single check valve falls within the recall parameters. The SC-3 single check valve needs to be replaced.
Figure 3 – SR-7 Spring Brake Modulating Valve Date Code Interpretation
Interpreting the Date Code
See Figure 3. A date code is stamped (not cast) on the SR-7 spring brake modulating valve body housing. Locate the date code – removing the paint coating if necessary – to read the code. Disregard the codes shown in gray in Figure 3. The portion of the date code that determines the date of manufacture is highlighted and can be interpreted as follows:
- The first field is the month (A = January, B = February, – excluding the letter I – so that J = September, and so on),
- The next two fields are the day of the month (e.g. 01 = 1st); and
- The next two fields are the year (e.g. 20 = 2020)
Technical Bulletin
Bulletin No: TCH-003-059 | Effective Date: 4/15/21 | Cancels: N/A |
Subject: BENDIX® SC-3™ SINGLE CHECK VALVE RECALL
(PART NUMBER K096210)
Bendix Commercial Vehicle Systems LLC (Bendix) is conducting a voluntary safety recall campaign, Recall No.: 21E-015, involving the Bendix® SC-3™ single check valve (Bendix Part Number K096210).
Problem Description:
See Figure 1. Bendix has determined that the retainer of the SC-3 single check valve, manufactured by a Bendix sub-supplier, may not have been seated in the internal groove of the valve, thereby causing a potential defect. Improperly seated retainers cause other internal components (the spring and the shuttle) of the SC-3 single check valve to become dislodged from the SC-3 fitting. After enough cycles with the spring and shuttle loose and out of the fitting, the shuttle or retainer can become fractured. If this condition exists and the pieces cannot be accounted for in the supply port of the Bendix® SR-7® spring brake modulating valve, then the SR-7 valve must be replaced as well.
Vehicles Affected:
This recall includes all SC-3 single check valve – part number K096210 – manufactured between July 27, 2020 and September 29, 2020. This action does not affect SC-3 single check valves manufactured prior to or after the stated dates.
What You Need To Do:
Immediately stop using and/or selling any of the SC-3 single check valves that fall within the recall parameters. It is a violation of Federal law for a dealer or distributor to sell an SC-3 single check valve that is subject to this recall. Ensure your customers are aware of the recall campaign.
Identification:
Blue Bird Vehicles
A potentially defective SC-3 single check valve on a Blue Bird vehicle has no date code identifier. Blue Bird purchased SC-3 single check valves from Bendix as standalone parts and not as part of an assembly. To identify a potentially defective SC-3 single check valve on a Blue Bird vehicle, perform the following steps:
1. Remove the SC-3 single check valve from the SR-7 spring brake modulating valve.
2. See Figure Inspect the SC-3 single check valve retainer. If the retainer is fully seated, it is correctly installed and not affected by this recall campaign. If the retainer is not fully seated – or is missing, damaged, or the shuttle or the retainer are missing or fractured – the SC-3 single check valve falls within the recall parameters. The SC-3 single check valve needs to be replaced. If the shuttle or the retainer are missing (not located in the SC-3 fitting nor in the supply port of the SR-7 spring brake modulating valve) or fractured, the SR-7 spring brake modulating valve must be replaced as well.
Figure 1 – SC-3 Single Check Valve
Internal Components – Spring and Shuttle
Figure 2 – SC-3 Single Check Valve Retainer
Navistar®, New Flyer, and Oshkosh Vehicles
NOTE: Any publication from the OEM supersedes the below information.
A potentially defective Bendix® SC-3™ single check valve on a Navistar, New Flyer, or Oshkosh vehicle was purchased from Bendix as an assembly including the SC-3 single check valve and the Bendix® SR-7® spring brake modulating valve. To identify a potentially defective SC-3 single check valve on a Navistar, New Flyer, or Oshkosh vehicle, perform the following steps:
1. Remove the SC-3 single check valve from the SR-7 spring brake modulating valve.
2. See Figure Inspect the SC-3 single check valve retainer. If the retainer is fully seated, it is correctly installed and not affected by this recall campaign. If the retainer is not fully seated – or is missing, damaged, or the shuttle or the retainer are missing or fractured – the SC-3 single check valve falls within the recall parameters. The SC-3 single check valve needs to be replaced. If the shuttle or the retainer are missing (not located in the SC-3 fitting nor in the supply port of the SR-7 spring brake modulating valve) or fractured, the SR-7 spring brake modulating valve must be replaced as well.
OR
1. See Figure 3. A potentially defective SC-3 single check valve that was purchased as part of an assembly with an SR-7 spring brake modulating valve can be identified by the date code on the SR-7 spring brake modulating If the SR-7 spring brake modulating valve has a date code that is any date between, and inclusive of, 7/27/20 and 9/29/20, the SC-3 single check valve falls within the recall parameters. The SC-3 single check valve needs to be replaced.
Figure 3 – SR-7 Spring Brake Modulating Valve Date Code Interpretation
Interpreting the Date Code:
See Figure 3. A date code is stamped (not cast) on the Bendix® SR-7® spring brake modulating valve body housing. Locate the date code – removing the paint coating if necessary – to read the code. Disregard the codes shown in gray in Figure 3. The portion of the date code that determines the date of manufacture is highlighted and can be interpreted as follows:
- The first field is the month (A = January, B = February, – excluding the letter I – so that J = September, and so on),
- The next two fields are the day of the month (e.g. 01 = 1st); and
- The next two fields are the year (e.g. 20 = 2020)
Inventory Disposition:
If your inventory contains Bendix® SC-3™ single check valves that fall within the recall parameters, please contact Ms. Shelly Neff. Please phone Shelly Neff, toll-free, by calling 1-800-AIR-BRAKE, ext. 4417 (1-800-247-2725, ext. 4417), Monday – Thursday, 8:00 a.m. – 6:00 p.m., and Friday, 8:00 a.m. – 5:00 p.m., ET, to arrange for the return of any affected inventory currently in stock. As a reminder, you will need to place an offsetting order to replenish the returned stock. Email SC-3campaign21@bendix.com for additional assistance.
Disposition of the Impacted SC-3 Single Check Valves:
You are authorized to scrap impacted SC-3 single check valves that are removed from vehicles. These valves are not required to be returned to Bendix.
Replacing Defective SC-3 Single Check Valves:
For instructions on replacing the SC-3 single check valve, reference SD-03-2205, Bendix SC-3 Single Check Valve Service Data Sheet, on bendix.com, or reference the SC-3 single check valve recall repair video on the Product Action Center on bendix.com.
SEOCONTENT-START
BLUE BIRD BODY COMPANY
3920 Arkwright Road, Suite 200, Macon, GA 31210 – (478) 825-2021
R21BE
IMPORTANT SAFETY RECALL NOTICE
NHTSA Campaign Number: 21V-284 (School Bus)
NHTSA Campaign Number: 21V-285 (Non-School Bus)
DATE: June 4, 2021
SUBJECT: R21BE – Bendix SC-3 Single Check Valve FMVSS 121 Noncompliance
Dear Blue Bird Owner:
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.
This important safety recall notice applies to your bus(es) identified by both Blue Bird Body Number and Vehicle Identification Number (VIN) on the enclosed yellow cover sheet. If you no longer own the subject bus(es), please complete the appropriate section of the yellow cover sheet and return to Blue Bird in the enclosed pink postage prepaid envelope.
Blue Bird Body Company is voluntarily recalling the following:
Certain model year 2020 to 2022 Blue Bird Vision School Buses
o manufactured from August 7, 2020 through January 25, 2021
Certain model year 2020 to 2022 All American School Buses
o manufactured from August 11, 2020 through January 28, 2021
Certain model year 2022 Blue Bird Vision Non-School Buses
o manufactured from September 3, 2020 through December 8, 2020
Certain model year 2022 Blue Bird All American Non-School Buses
o manufactured from September 10, 2020 through February 3, 2021
On the subject buses, it has been determined that certain Blue Bird buses could fail to conform to the Federal Motor Vehicle Safety Standard Number 121, Air Brake Systems. A retainer was not properly seated during assembly of the SC-3 Single Check valve, such that when air pressure is applied, it may no longer provide source air isolation as defined and required by FMVSS 121. Unintended spring brake application may occur, increasing the risk of a crash.
Blue Bird shall conduct a voluntary safety recall to correct this noncompliance.
Corrective Action:
To correct this noncompliance, Blue Bird will notify the affected owners and will provide inspection and repair instructions. All SC-3 Check Valves manufactured between July 27, 2020, and September 9, 2020 are subject to this recall. The recalled SC-3 Single Check Valves may not have the retainer fully seated in the retainer groove. The SC-3 Check Valves that are not subject to this recall have the retainer fully seated in the retainer groove. The safety risk is a spring brake application that is uncommanded by the driver may result. Recall R21BE should be inspected and repaired, per R21BE Recall Instructions. You may request parts at campaignparts@blue-bird.com Parts are currently available.
Labor Reimbursement:
Blue Bird will reimburse the labor cost of potential repairs relating to this recall at no cost to you the vehicle owner. The Standard Repair Time (SRT) to accomplish this repair is outlined below:
R21BE Inspection and Repair
o 0.5 hours (30 minutes)
BLUE BIRD BODY COMPANY
3920 Arkwright Road, Suite 200, Macon, GA 31210 – (478) 825-2021
Blue Bird Body Company R21BE
Page 2
Administering the Recall:
Blue Bird recommends that you contact your local or nearest Blue Bird Dealer to arrange for this recall to be performed. The Dealer can perform the repairs, or arrange for repairs to be performed by a service repair facility authorized by the Dealer. However, you may elect to perform this recall yourself or pay another independent repair facility to perform this recall. A qualified technician should perform this recall. If you elect to perform this recall yourself or pay another independent repair facility to perform this recall, complete and submit the Pink Owner’s Recall Reply Sheet provided. The Recall Reply Sheet includes a section for the owner to request reimbursement of the owner’s labor or to request reimbursement for a labor invoice paid by the owner to an independent repair facility.
Parts to complete Recall R21BE are currently available.
Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.
If the modifications directed by this notification were performed on your bus prior to the receipt of this recall notification, attach a copy of the work order/invoice. Mail the documents in the pink self-addressed postage prepaid envelope included with the pink reply sheet to Blue Bird for warranty consideration. Reimbursements will be made in accordance with the requirements of the National Highway Transportation Safety Act, Title 49 Code of Federal Regulations, Parts 573 and 577.
Please contact your local Blue Bird Dealer with any questions regarding this recall campaign.
If Blue Bird Body Company should fail to or is unable to remedy this condition without charge to you, you may contact:
ADMINISTRATOR
NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION
1200 NEW JERSEY AVENUE, SE
WASHINGTON, D.C. 20590
Or, you may call The National Highway Traffic Safety Administration toll free at:
1-888-327-4236 TTY 1-800-424-9153 or go to: http:/www.safercar.gov
*********************************************************************************************
BLUE BIRD BODY COMPANY
3920 Arkwright Road, Suite 200, Macon, GA 31210 – (478) 825-2021
R21BE
IMPORTANT SAFETY RECALL NOTICE
NHTSA Campaign Number: 21V-284 (School Bus)
NHTSA Campaign Number: 21V-285 (Non-School Bus)
DATE: June 4, 2021
TO: U.S. DEALERS
SUBJECT: R21BE – Bendix SC-3 Single Check Valve FMVSS 121 Noncompliance
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.
This important safety recall notice applies to your buses identified by both Blue Bird Body Number and Vehicle Identification Number (VIN) on the attached yellow cover sheet.
Blue Bird Body Company is voluntarily recalling the following:
Certain model year 2020 to 2022 Blue Bird Vision School Buses
o manufactured from August 7, 2020 through January 25, 2021
Certain model year 2020 to 2022 All American School Buses
o manufactured from August 11, 2020 through January 28, 2021
Certain model year 2022 Blue Bird Vision Non-School Buses
o manufactured from September 3, 2020 through December 8, 2020
Certain model year 2022 Blue Bird All American Non-School Buses
o manufactured from September 10, 2020 through February 3, 2021
On the subject buses, it has been determined that certain Blue Bird buses could fail to conform to the Federal Motor Vehicle Safety Standard Number 121, Air Brake Systems. A retainer was not properly seated during assembly of the SC-3 Single Check valve, such that when air pressure is applied, it may no longer provide source air isolation as defined and required by FMVSS 121. Unintended spring brake application may occur, increasing the risk of a crash.
Blue Bird shall conduct a voluntary safety recall to correct this noncompliance.
Corrective Action:
To correct this noncompliance, Blue Bird will notify the affected dealers and owners and will provide inspection and repair instructions. All SC-3 Check Valves manufactured between July 27, 2020, and September 9, 2020 are subject to this recall. The recalled SC-3 Single Check Valves may not have the retainer fully seated in the retainer groove. The SC-3 Check Valves that are not subject to this recall have the retainer fully seated in the retainer groove. The safety risk is a spring brake application that is uncommanded by the driver may result. Recall R21BE should be inspected and repaired, per R21BE Recall Instructions. You may request parts at campaignparts@blue-bird.com Parts are currently available.
Labor Reimbursement:
Blue Bird will reimburse the labor cost of potential repairs relating to this recall at no cost to you the Dealer or to the vehicle owner. The Standard Repair Time (SRT) to accomplish this repair is outlined below:
R21BE Inspection and Repair
o 0.5 hours (30 minutes)
BLUE BIRD BODY COMPANY
3920 Arkwright Road, Suite 200, Macon, GA 31210 – (478) 825-2021
Blue Bird Body Company R21BE
Page 2
Administering the Recall:
Parts to complete Recall R21BE are currently available.
If Blue Bird’s records indicate bus(es) subject to this recall were delivered in your service area, a list of affected bus(es) will be enclosed. The bus(es) will be identified by Blue Bird Body Number and Vehicle Identification Number (VIN) on the enclosed yellow cover sheet. Dealers should verify correct owners and assure that complete mailing and shipping addresses are provided for each listed owner.
It is the Dealer’s responsibility to verify that the correct owner name, address, and telephone number is provided for each listed vehicle. Any corrections or updates should be made in ClaimsCenter. Addresses that cannot be updated should be forwarded to the Recall Administrator.
Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.
Dealers are reminded of their responsibilities under Section 154 of The National Traffic and Motor Vehicle Safety Act of 1991. Dealers are required to complete modifications on units in their inventory before delivering to the final owner. Reference Blue Bird Body Company Distributor Memo No. 42-92.
If you have in your possession or have sold a bus that was purchased from another Dealer that may be affected by this recall, please notify Lisa Hancock at 478-822-2242 or lisa.hancock@blue-bird.com Questions regarding this recall campaign should be directed to Lisa Hancock, as well.
Sincerely,
Lisa Hancock
Corporate Recall Administrator
Blue Bird Corporation
3920 Arkwright Road, Suite 200, Macon, Georgia 31210
Phone 478.822.2242
lisa.hancock@blue-bird.com
SEOCONTENT-END
6 Affected Products
Vehicles
MAKE | MODEL | YEAR |
BLUE BIRD | ALL AMERICAN | 2020-2022 |
BLUE BIRD | VISION | 2020-2022 |
9 Associated Documents
Recall Quarterly Report #1, 2021-2
RCLQRT-21V284-3204.PDF 211.145KB
Remedy Instructions and TSB
RCRIT-21V284-3891.pdf 2748.332KB
ISSUED Owner Notification Letter(Part 577)
RCONL-21V284-3304.pdf 804.224KB
Manufacturer Notices(to Dealers,etc)
RCMN-21V284-0629.pdf 857.073KB
Noncompliance Notice 573 Report
RCLRPT-21V284-6140.PDF 214.029KB
Recall Acknowledgement
RCAK-21V284-1270.pdf 692.042KB
Recall Quarterly Report #3, 2021-4
RCLQRT-21V284-8109.PDF 211.331KB
ISSUED Renotification Notice
RCRN-21V284-2893.pdf 4125.189KB
Recall Quarterly Report #2, 2021-3
RCLQRT-21V284-3066.PDF 211.243KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=21V284&docType=RCL
- Audible Audiobook
- Mile One Press (Author) - John Flaherty (Narrator)
- English (Publication Language)
- 12/15/2022 (Publication Date) - Mile One Press (Publisher)
- 【43 PCS PACKAGE】- The DOT air brake fittings kit includes: 6 pcs brass tube tee fittings, 6 pcs brass straight union connectors, 14 pcs brass straight push connectors NPT thread, 14 pcs 90°elbows NPT thread, 2 pcs brass 1/4" inflation Schrader valve, 1 pc tube cutter. Air brake fitting assortment types: 1/8", 1/4", 3/8", 1/2".
- 【PREMIUM QUALITY】- Our DOT air hose fittings are made of high-quality CA360 brass, meets D.O.T. FMVSS 571.106 approved, SAE J1131 air brake system requirements, with corrosion resistance, high-temperature ductility, low permeability and long service life.
- 【MAX WORKING INTENSITY】- The brass fittings can be operated in pressures from vacuum to 250psi and in temperatures from -40°F to +200°F (-40°C to +93°C). Note: see the tubing manufacturer's recommendations for pressure and temperature mutations.
- 【EASY INSTALLATION】- The quick connect design and precise NPT threading make installation of air brake accessories easy, just push to connect. And there is pre-applied sealant on NPT male thread for better sealing.
- 【WIDE APPLICATION】- The brass DOT air brake fittings can be used with air suspension systems, copper tubing in airlines brake systems, perfect for truck /RV repair air line leak, also ideal for industrial workshops, daily garden or lawn mower repair, towing machine hose connection, etc.
- Direct Replacement Easy to Install
- Replaces || Red Air Supply Knob: Bendix 298817 | Yellow Parking Brake Knob: Bendix 298818
- Application || Mount on Threaded Mv-3 type dash valve to moderate pressure
- Quality || Made High Quality Plastic solid light And durable
- Specs || Thread: 5/8"
- 【14 PCS PACKAGE】- The air hose & DOT air fittings kit includes: 50 ft 1/4" air hose, 4 pcs 1/4" tee fittings, 4 pcs 1/4“ straight union, 2 pcs 1/4" 90°elbows, 2 pcs 1/4" Y splitters, 1 pc tube cutter. Air brake fitting assortment types: 1/4".
- 【PREMIUM DOT FITTINGS】- Our DOT air hose fittings are made of high-quality CA360 brass and high-strength plastic, meet D.O.T. FMVSS 571.106 approved, SAE J1131 air brake system requirements, with corrosion resistance, high-temperature ductility, low permeability and long service life.
- 【PREMIUM PA12 AIR HOSE】- Our air hose fittings are made of high-quality PA12 Polyamide, meet D.O.T. FMVSS 571.106 approved, SAE J844 air brake system requirements, with corrosion resistance, high-temperature ductility, high pressure resistance and long service life.
- 【MAX WORKING INTENSITY】- The brass fittings can be operated in pressures from vacuum to 250 PSI and in temperatures from -30°F to +180°F (-34°C to +82°C). Note: see the tubing manufacturer's recommendations for pressure and temperature mutations.
- 【EASY INSTALLATION】- The DOT quick connect design makes the installation of air brake accessories easy, just push to connect.
- 【High Quality in Air Brake Coiled】Our air brake coiled hose is designed with superior craftsmanship and high quality nylon materials, delivering a reliable and secure connection for your air brake system.The reinforced air hose provides added protection and longer lasting performance.
- 【Brass Fitting】Air hose coiled with a 1/2" swivel brass fitting and spring guard for a secure, tractor-end connection, these air lines meet or exceed SAE J844 A hose requirements and DOT FMVSS 106 ensuring that you're getting a product that meets industry standards.
- 【SPRING JOINT】Designed air coil and power cord with a spring guard for easy coupling and uncoupling, save you time and effort. Plus, their durable construction and easy-to-install design provide peace of mind and reliable performance for years to come.
- 【Why Choose Us?】7 Way Trailer coiled is made of pure copper for long-lasting performance and excellent electrical and thermal conductivity. This ensures that your car lights, such as turn signals and brake lights, work properly during your drive.
- 【Versatile Applications】 Dazakoot electric power cables are perfect for connecting the trailer, brake, reverse, turn signals and auxiliary power on your tail, RV, camper, caravan, food van, and other towed vehicles. Before beginning any operations on the product, please refer to the diagram for guidance.
- Comprehensive Kit: the DOT air brake fittings kit includes 12 DOT union, 6 DOT tee, 4 bushing, 8 DOT male elbow connector (90°), 8 DOT straight male connector, 4 DOT male elbow connector (45°), 2 compression fittings 1/4" tube and 1/4" male, and 1 tubing cutter; Fitting types, 1/4", 3/8", 1/2", 1/8", 5/8"; They are packed in a plastic storage box with flip lock tabs; This comprehensive assortment ensures that you have the right fittings for various connections and configurations
- Quality Material: crafted mainly from CA360 brass, these air line fittings are meet with D. O. T. FMVSS 571.106 certification and compatible with SAE J1131 air brake system requirements; They are corrosion resistant, exhibit high temperature ductility, low permeability, and boast a long service life; The use of quality material ensures reliability and longevity in various air brake system applications
- Maximum Working Strength: the brass components in this brake line fittings set can operate under pressures ranging from vacuum to 300psi and temperatures from -40°F to +200°F (-40°C to +93°C); It's important to refer to the pressure and temperature recommendations from the pipe manufacturer for optimal performance and safety
- Easy Installation: featuring a quick connect design and precise threads compatible with NPT, these air brake fittings facilitate simple installation with a push to connect mechanism; Additionally, you can apply sealant on the external threads to enhance the sealing effect, making the installation process more efficient and reliable
- Wide Application: this brass air fittings set is suitable for use in air suspension systems, copper tubing in airline brake systems, truck air pipe leak repairs, industrial workshop applications, as well as maintenance for everyday garden or lawn equipment and trailer hose connections; The broad applicability of these fittings makes them a practical choice for various scenarios
- Contain common air brake fitting styles
- D.O.T Union:1/4"(4 pcs), 3/8"(4 pcs), 1/2"(4 pcs), 5/8"(2 pcs)
- D.O.T Tee:1/4"(2 pcs), 3/8"(2 pcs), 1/2"(2 pcs); Bushing: 3/8" NPT Female x 1/2" NPT Male(2 pcs)
- D.O.T Male Elbow:1/4" OD x 1/8" NPT Male(2 pcs), 1/4" OD x 1/4" NPT Male(2 pcs), 3/8" OD x 3/8" NPT Male(2 pcs), 1/2" OD x 3/8" NPT Male(2 pcs)
- D.O.T Sraight Male Connector: 1/4" x 1/8" NPT Male(2 pcs), 1/4" x 1/4" NPT Male(2 pcs), 3/8" x 3/8" NPT Male(2 pcs), 1/2" x 3/8" NPT Male(2 pcs)
- 【Includes 1 Cutter】For no air leakage, the cross section of the air line must be smooth and flat, no gap, uneven, and the tube cannot be oval. Our air tube come with a tube cutter to make cutting more convenient and easier!
- 【SAE J 844 DOT Approved】SAE J 844 Type 1/4” OD × 50FT Air Brake Line DOT approved, Tube Size: 1/4" OD × 4.35mm ID, Working Temperature: -40℉ to +248℉(-40℃ to +120℃), Max Working Pressure: 200 PSI.
- 【PA12 Nylon - High Resistance & Multiple Transfer】Boeray 1/4 inch × 50’ air hose is made of high quality Polyamide 12 nylon, meet a wide range of transportation needs, such as water, air, fuel, oil, etc. High quality abrasion and impact resistance to withstand most wear and tear.
- 【High Flexibility for easy bending】High toughness nylon tube, you can bend it easily. Note: please bend it under limited condition, do not over bend it to affect the usage.
- 【Application】Our 50ft air line is perfect for air suspension and air brake systems, fluid transfer like water oil and fuel for automotive vehicle marine, chemical transport, instrumentation lines, paint spraying, garden irrigation control systems, LPG and compressed natural gas systems, misting systems, pneumatic systems, Clutch Systems, etc.
Last update on 2024-04-11 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.