BC1000XL Wheel and Tire Assembly Replacement Kit (IK00-3940) – Vermeer

Subject:

PRODUCT SAFETY RECALL

FIRST NOTICE

Tire Assembly Replacement Kit (IK00-3940)

Field remedy now available.

1. IK01, IK03: Order one of these kit versions which includes English Supplemental Operator’s and Maintenance Manual for machines located in the United States, Canada (except Quebec), Australia or New
2. IK02, IK04: Order one of these kit versions which includes English + translated Supplemental Operator’s and Maintenance Manuals for machines located in other global regions,

Additional details regarding kit versions and parts included are shown below.

Background:

Dealers were previously notified on Service Bulletin SVC2020-052Rev1, SVC2020- 056 and SVC2020-057 about a supplier wheel safety defect.

Defective Supplier Wheel

Improper Lug Nut Seat and Potential Cracks

Identified by continuously raised lug nut surface

Properly Manufactured Wheel

Correct Lug Nut Seat

Identified by raised surface only around lug nut location

These Service Bulletins provided instructions for:

1. Destruction of dealer inventory for affected part numbers:

2. Install temporary solution (Assembly PN 163769457) on units that could not maintain torque and/or tire pressure.

3. Owner notifications to inspect each wheel to determine if supplier wheels were installed and to notify Vermeer Corporation of the inspection results.

POSSIBLE LOSS OF WHEEL AND RISK OF CRASH

Specific wheels (steel rim) with bolt pattern 8 on 6½ inch (165 mm) circle to be used with 5/8” studs provided by a supplier [only 7000 lb (3175 kg) electric brake axle configuration]:

• have an incorrect lug nut contact area causing wheel lug nuts to loosen; and/or

• can develop possible cracks causing the tire to lose air pressure.

DEATH OR SERIOUS INJURY POSSIBLE

Both conditions may increase the risk of wheel loss and the risk of a crash. Death or serious injury is possible. Property damage may also occur.

Solution: 

IMMEDIATE MACHINE MODIFICATIONS REQUIRED

IK00-3940 has been created to provide the necessary parts and instructions to replace the wheel and tire assembly, install a new safety sign (shown at right), a new wheel/tire specification placard decal, and provide a Supplemental Operator’s and Maintenance Manual.

Please be reminded that it is a violation of Federal law for you to sell or lease the machines covered by this notification until this recall has been performed on these machines. Substantial civil penalties apply to violations of this law.

1. Kit versions descriptions and instructions:

a. IK01-3940: Includes wheels, tires, safety sign, wheel/tire specification placard decal, English supplemental manual

b. IK02-3940: Includes wheels, tires, safety sign, wheel/tire specification placard decal, English + translated supplemental manual

Destroy wheel and tires. When you remove the supplier defective steel rim/wheels, these wheels can never be used or sold for any purpose. The wheels MUST be destroyed:

• Remove the tire from the steel rim/wheel or deflate the tire.

• Torch cut the wheel(s) across the lug nut area.

• Take photo(s) of the destroyed wheel(s) and attach to campaign warranty claim.

• Discard the lug nuts so they can never be used or sold for any purpose.

• The removed used tires may be retained in your used tire inventory or disposed of. The cost of tire removal and disposal is included in the labor hours.

c. IK03-3940: NO wheels and tires; Includes safety sign, wheel/tire specification placard decal and English supplemental manual

d. IK04-3940: NO wheels and tires; Includes safety sign, wheel/tire specification placard decal and English + translated Supplemental Manual

ONLY for machines that Temporary wheel/tire assembly solution (Assembly PN 163759457) was previously installed.

Note: BC1000XL production machines with 7000 lb axle will be equipped with the 17.5” wheel/tire assembly identified in this field campaign kit.

DEALER PARTICIPATION

REVIEW REPORT, ORDER KITS, CONTACT CUSTOMERS

1. Reports will be emailed during the week of July 16, 2020, to dealerships shown in our records which have units in their territory affected by this Alert. Please review the report for accuracy, including owner and/or address changes.

If the information contained in the report is NOT correct, please notify the Product Safety Department on or before July 29, 2020 at:

Telephone:      641-621-7060

Fax:                 641-621-8562

Email:              productsafety@vermeer.com

2. Dealerships Order Kits by entering the order into iParts/EZParts.

Each dealership should determine the quantity of Kits to order initially depending upon the number of units that may be available for immediate upgrade. Do not order more Kits than needed for immediate installation.

3. Translated Manuals. For those dealers in global locations where English is not the primary/official language, iParts/EZParts will require the Model and VIN be entered at time of order to enable a translated Supplement Manual to be provided in the official/primary If the translated Supplemental Manual is available in the language required at time of order, the translated manual will be shipped with IK02 and IK04 from the Parts Distribution Center. If the translated Supplemental Manual is not yet available, the translated manual will be sent from Product Safety department when it becomes available referencing the Sales Order number of IK02 or IK04, Model and VIN.

4. Contact your affected customer(s) to schedule a mutually acceptable time to upgrade their Note: Letters will be sent to the customer(s) on or about July 30, 2020. Also refer to Owner Notification section below.

If you have any questions concerning the installation of IK00-3940, please contact the Environmental Service Department.

REIMBURSEMENT

Upon completion of each Kit installation, a campaign Warranty Claim must be submitted to the Corporate Warranty Department for reimbursement of the cost of the parts and labor to install the Kit. Campaign Warranty Claim:

1. Must include photos of destroyed wheels (IK01, IK02 only).
2. Must include a copy of the Work Order if travel is requested.

Labor hours to install IK01 or IK02: 2.0 hours. Note: Tire disposal is included in the labor hours. No additional reimbursement will be paid.

Labor hours to install IK03 or IK04: 1.0 hours. No photos for installation of these kit versions are required. Applicable only if Temporary Wheel Solution (Assembly PN 163769457) was previously installed.

If dealer assists owner with wheel inspection, dealer will be reimbursed 1.0 hour labor. Dealer must submit standard warranty claim with wheel photos and inspection form attached referencing IK003940 in causal part number field.

If a customer submits inspection form directly to Vermeer Corporation, the dealer will not also be paid for a second inspection.

Note: Future notices to dealers and owners are dependent upon the receipt of Warranty Claims.

OWNER NOTIFICATION

Sample Letters: Included at the end of this Bulletin are sample letters which will be sent by Vermeer Corporation directly to the Owners on or about July 30, 2020, via USPS certified/registered mail. Please note there are two sample letters:

• Letter 1: Owners who responded to interim mailing that wheels were defective or who had the temporary wheel solution
• Letter 2: Owners who did not respond to the interim

Owner registrations indicate no translations are required for this campaign. The owner letter will be available in English only.

This owner notification/letter instructs the owner to contact their local dealership to arrange for a time to have the Kit installed. After receiving IK00-3940 from the Parts Center, you must contact your affected customer(s) immediately and schedule a mutually acceptable time to upgrade their machine.

We regret any inconvenience these corrective measures may cause you. This required work is for the safety of the crew, the towing vehicle occupants and others traveling the public roadways. We hope you agree the safety benefits surpass the inconvenience.

PRODUCT SAFETY DEPARTMENT

Attachment:

IK00-3940 Kit Instructions

Sample Owner Letter #1 – Temporary wheel solution installed, or Inspection indicated defective wheels

NHTSA SAFETY RECALL NUMBER 20V-085

IMPORTANT SAFETY RECALL

First Notice

BC1000XL Wheel and Tire Assembly Replacement Kit (IK00-3940)

Field campaign remedy is now available.

Model: «Model»
This notice applies to your vehicle,
Serial No: «VIN»

VIA USPS CERTIFIED/REGISTERED MAIL

July 30, 2020

Dear «MODEL» Owner:

This notice is sent to you in accordance with the requirements of the U.S. National Traffic and Motor Vehicle Safety Act.

In March 2020, Vermeer decided that a defect, that relates to motor vehicle safety, existed in certain model year 2016–2020 Vermeer «MODEL» brush chippers. At that time, Vermeer Corporation sent owners an interim notice asking owners to inspect the wheels. Thank you for returning the inspection form and/or contacting your dealer for the temporary wheel solution. The final field campaign remedy is now available.

What is the issue?

Certain brush chippers with specific wheels (steel rim) with bolt pattern 8 on 6½ inch (165 mm) circle to be used with 5/8-inch studs provided by a supplier:

• have an incorrect lug nut contact area causing the wheel lug nuts to loosen; and/or
• can develop possible cracks causing the tire to lose air pressure.

Both conditions may increase the risk of wheel loss and the risk of a crash. Death or serious injury is possible. Property damage may also occur.

IMMEDIATE MACHINE MODIFICATIONS REQUIRED

IK00-3940 has been created to provide the necessary parts and instructions to replace the wheel and tire assembly, install a new safety sign (shown on next page), install a new wheel/tire specification placard decal, and provide a Supplemental Operator’s and Maintenance Manual. This kit must be installed as soon as possible.

If your dealer did not install the temporary wheel solution, prior to having this field remedy kit installed please continue to verify the torque of each lug nut [210 ft-lb (285 Nm)] and tire pressure [80 psi (550 kPa)] as part of your pre-trip inspection every day or at a minimum every 150 miles (250 km) until IK00-3940: Wheel and Tire Assembly Replacement Kit is installed by your dealer.

Wheels and tires included in this field remedy kit are:

Please contact your authorized, independent Vermeer dealer immediately to arrange a mutually acceptable time and location to install IK00-3940 at no cost to you for labor or materials. The installation of this kit is estimated at 2.0 hours of labor. If the Vermeer dealer travels to the unit to install the kit, costs may be incurred by the owner.

If your dealer installed a temporary wheel/tire assembly solution (Assembly PN 163759457) since receiving the March 2020 notice, the wheels and tires are part of the final field remedy kit and will remain on your brush chipper. However, to complete this field remedy kit, the dealer will install a new safety sign and a new wheel/tire specification placard decal and provide a Supplemental Operator’s and Maintenance Manual. The installation of this kit version is estimated at 1.0 hour of labor. If the Vermeer dealer travels to the unit to install the kit, costs may be incurred by the owner.

You must have your machine upgraded for these safety features Contact your local Vermeer Dealer:

Contact your local Vermeer Dealer:

«Service_Dealer_Name»
«Serv_Dealer_Add1» «Serv_Dealer_Add2»
«Serv_Dealer_City» «Serv_Dealer_St» «Serv_Dealer_Zip»
«SERV_DEALER_COUNTRY»

Telephone:

«Serv_Dealer_Phone»

According to our records, you currently own a Vermeer «MODEL» brush chipper. The Model and Serial Number of the «MODEL» is shown at the top right of this letter. If you no longer own this unit, please notify the Product Safety Department at:

Toll Free: 800-829-0051, extension 7060
Telephone: 641-621-7060
E-mail: productsafety@vermeer.com

If possible, please provide the name and address of the new owner.

We regret any inconvenience these corrective measures may cause you. This required work is for the safety of the crew, the towing vehicle occupants and others traveling the public roadways. We hope you agree the safety benefits surpass the inconvenience.

Very truly yours,

PRODUCT SAFETY DEPARTMENT

Federal regulations require that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten (10) days.

If the authorized dealer has failed or is unable to remedy the defect without charge and within a reasonable time, contact Vermeer Product Safety by email at productsafety@vermeer.com or by calling 800-829-0051 or 641-621-7060. You may also submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, D.C. 20590 or call the Vehicle Safety Hotline at 888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov

Sample Owner Letter #2 – NO Owner inspection response received, unknown wheel status

NHTSA SAFETY RECALL NUMBER 20V-085

IMPORTANT SAFETY RECALL

First Notice

BC1000XL Wheel and Tire Assembly Replacement Kit (IK00-3940)

Field campaign remedy is now available.

VIA USPS CERTIFIED/REGISTERD MAIL

Model: «Model»
This notice applies to your vehicle,
Serial No: «VIN»

July 30, 2020

Dear «MODEL» Owner:

This notice is sent to you in accordance with the requirements of the U.S. National Traffic and Motor Vehicle Safety Act.

In March 2020, Vermeer decided that a defect, that relates to motor vehicle safety, existed in certain model year 2016–2020 Vermeer «MODEL» brush chipper. At that time, Vermeer Corporation sent owners an interim notice (a copy is enclosed) asking owners to inspect the wheels and complete and return a Wheel Lug Nut inspection form and wheel photos. According to our records, you have not returned the inspection form and/or contacted your dealer regarding this field issue. The final field campaign remedy is now available.

What is the issue?

Certain brush chippers with specific wheels (steel rim) with bolt pattern 8 on 6½ inch (165 mm) circle to be used with 5/8-inch studs provided by a supplier:

• have an incorrect lug nut contact area causing the wheel lug nuts to loosen; and/or
• can develop possible cracks causing the tire to lose air pressure.

Both conditions may increase the risk of wheel loss and the risk of a crash. Death or serious injury is possible. Property damage may also occur.

IMMEDIATE WHEEL INSPECTION REQUIRED

1. WHEEL AND LUG NUT INSPECTION. Inspect each brush chipper wheel by referencing the photos to identify if defective supplier wheels are installed. If you own more than one affected brush chipper, you will receive a letter for each The Model and VIN is shown on the top right of this letter and the Wheel Lug Nut Inspection form.

2. Does not have defective supplier wheels: See enclosed Wheel Lug Nut Inspection form to be completed and returned to: safetyform@vermeer.com. Owners who return the Wheel and Lug Nut Inspection form with photos identifying no defective supplier wheels will be mailed a Vermeer Parts Certificate for $50 USD redeemable at your local Vermeer dealer. If you do not return the Inspection form, Vermeer Corporation will continue to send further communications regarding this recall.

3. Has defective supplier wheels, contact your local Vermeer Dealer for new wheel and tire assembly. IK00-3940 has been created to provide the necessary parts and instructions to replace the wheel and tire assembly, install a new safety sign (shown at below), install a new wheel/tire specification placard decal, and provide a Supplemental Operator’s and Maintenance Manual. This kit must be installed as soon as possible.

If your dealer did not install the temporary wheel solution and until IK00- 3940: Wheel and Tire Assembly Replacement Kit is installed by your dealer, please continue to verify the torque of each lug nut [210 ft-lb (285 Nm)] and tire pressure [80 psi (550 kPa)] as part of your pre-trip inspection every day or at a minimum every 150 miles (250 km).

Wheels and tires included in this field remedy kit are:

Please contact your authorized, independent Vermeer dealer immediately to arrange a mutually acceptable time and location to install IK00-3940 at no cost to you for labor or materials. The installation of this kit is estimated at 2.0 hours of labor. If the Vermeer dealer travels to the unit to install the kit, costs may be incurred by the owner. You must have your machine upgraded for these safety features.

If your dealer installed a temporary wheel/tire assembly solution (Assembly PN 163759457) since receiving the March 2020 notice, the wheels and tires are part of the final field remedy kit and will remain on your brush chipper. However, to complete this field remedy kit, the dealer will install a new safety sign and a new wheel/tire specification placard decal and provide a Supplemental Operator’s and Maintenance Manual. The installation of this kit version is estimated at 1.0 hour of labor. If the Vermeer dealer travels to the unit to install the kit, costs may be incurred by the owner.

You must have your machine upgraded for these safety features.

Contact your local Vermeer Dealer:

«Service_Dealer_Name»
«Serv_Dealer_Add1» «Serv_Dealer_Add2»
«Serv_Dealer_City» «Serv_Dealer_St» «Serv_Dealer_Zip»
«SERV_DEALER_COUNTRY»

Telephone:

«Serv_Dealer_Phone»

According to our records, you currently own a Vermeer «MODEL» brush chipper. The Model and Serial Number of the «MODEL» is shown at the top right of this letter. If you no longer own this unit, please notify the Product Safety Department at:

Toll Free: 800-829-0051, extension 7060
Telephone: 641-621-7060
E-mail: productsafety@vermeer.com

If possible, please provide the name and address of the new owner.

We regret any inconvenience these corrective measures may cause you. This required work is for the safety of the crew, the towing vehicle occupants and others traveling the public roadways. We hope you agree the safety benefits surpass the inconvenience.

Very truly yours,

PRODUCT SAFETY DEPARTMENT

Enclosures

• March 12, 2020 Interim Notice Wheel and Lug Nut Inspection
• First Notice Wheel and Lug Nut Inspection Form

Federal regulations require that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten (10) days.

If the authorized dealer has failed or is unable to remedy the defect without charge and within a reasonable time, contact Vermeer Product Safety by email at productsafety@vermeer.com or by calling 800-829-0051 or 641-621-7060. You may also submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, D.C. 20590 or call the Vehicle Safety Hotline at 888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov

Safety Bulletin

RCSB-20V085-5046.pdf 1712.07KB

Loading...

Taking too long?

Reload document

| Open in new tab

Download [1.63 MB]

Bestseller No. 1

12x1.5 Lug Nuts 20 Pcs Chrome Closed End Mag Style Lug Nuts with Washer 13/16" (21mm) Hex Compatible with Toyota Camry/Corolla/Tacoma Lexus

• One-piece Solid lug nuts feature durable design and provide perfect replacement for your Tacoma, 4Runner, Corolla, GX470
• Specifications: 12x1.5 Thread Pitch; 13/16'' (21mm) Hex; 1.49" (38mm) OAL; Closed End; Color: Chrome
• 10.9-grade Heat-treated premium steel construction, which offers better durability and strength.
• Replace Part # 9094201058, 9008017036, 90942-01058, 9008-17036, 9094201084
• One-piece lug nuts unlike OEM OEM Cap Construction lug nuts, which means Reeauto's Lug nuts will definitely not break apart like your TOYOTA, LEXUS stock lug nuts

$18.90

Buy on Amazon Price incl. tax, excl. shipping

Bestseller No. 2

MIKKUPPA M12x1.5 Lug Nuts - Replacement for 2006-2019 Ford Fusion, 2000-2019 Ford Focus, 2001-2019 Ford Escape Aftermarket Wheel - 20pcs Chrome Closed End Lug Nut

• 🚗 WE' RE DIFFERENT - MIKKUPPA innovative closed end bulge Lug Nuts design provides a safer and more reliable closed end nut than any other on the market. One-piece design compared with other two-piece design, Anti-cracking off and make it aesthetically pleasing while ensuring safe driving. 【This kit does not hold the wheel cover! ! !】
• 🚗 PERFECT FIT - Replacement for 2004-2019 Acura TSX. 2002-2019 Chevy Trailblazer, 2001-2019 Ford Escape, 2000-2019 Ford Focus, 2006-2019 Ford Fusion, 1999-2019 Honda Accord/CR-V, 2005-2019 KIA Sportage LX EX, 1995-2019 Toyota Avalon, etc.
• 🚗 SPECIFICATION - M12x1.5 thread - closed end bulge style lug nuts - conical 60 degree seat - 19mm hex - 35.05mm long - 22mm wide - color: silver / chrome. Our nuts have an innovative design in appearance due to personal preference, but the thread specifications fully meet vehicle standards, buy with confidence.
• 🚗 ONE-PIECE LUG NUTS - The one-piece structure design is more splendid and safer than the two-piece design. Triple chrome, cold forged and heat treated steel, anti-rusting and anti-stripped, high strength and durability.
• 🚗 WORRY-FREE SHOPPING EXPERIENCE - We go above and beyond to provide the highest quality wheel lug nut and top notch customer service. Contact us and we will give you a satisfactory answer within 24 hours. The 12-month warranty gives you a worry-free shopping experience.

$19.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 3

White Knight 1707S-20AM Chrome M12x1.50 Bulge Acorn Lug Nut, 20 Count (Pack of 1)

• For Select Aftermarket and Factory Wheels.
• Specifications: M12 x 1.50 Thread Pitch, 1.40” Overall Height, 0.90" Diameter, 3/4" Hex, 60° Conical Seating, Bulge Acorn.
• Features: Cold forged carbon steel and tested to industry standards. Durable construction. Stylish chrome or black chrome finish. Utilizes traditional hex-body bulge-acorn design for fast and easy installation.
• ATTENTION: Refer to the owner’s manual or the wheel manufacturer’s guide for the correct thread size, seat style, length, hex and torque specifications. You assume all liability of improper installation which can result in accident and/or injury.
• 1 year manufacturer warranty. Always check your vehicle fitment before purchasing! Contact us for warranty replacement or fitment issues.

$21.99 −$4.00 $17.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 4

Dorman 711-265 Wheel Nut Chrome Acorn Bulge Seat 1/2-20 Compatible with Select Models, 20 Pack, Medium

• Direct replacement - these wheel lug nuts are designed to match the fit, function and performance of the original equipment hardware on specified vehicles
• Ensure fit - available in a variety of sizes and assortments, please check product dimensions and details to ensure you select the right wheel lug nut(s) for your application
• Durable construction - designed and manufactured to strict specifications for reliable performance
• Trustworthy quality - backed by a team of product experts in the United States and more than a century of automotive experience
• Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool

$17.71 −$7.39 $10.32

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 5

White Knight Wheel Lug Nuts - 12x1.5 Lug Nuts, 1707S-4, 4 Pack, M12x1.50 Bulge Acorn Chrome Lug Nuts, Steel with Stylish Chrome Finish, Easy to Install, Durable Construction

• For Select Aftermarket and Factory Wheels.
• Specifications: M12 x 1.50 Thread Pitch, 1.40” Overall Height, 0.90" Diameter, 3/4" Hex, 60° Conical Seating, Bulge Acorn.
• Features: Cold forged carbon steel and tested to industry standards. Durable construction. Stylish chrome or black chrome finish. Utilizes traditional hex-body bulge-acorn design for fast and easy installation.
• ATTENTION: Refer to the owner’s manual or the wheel manufacturer’s guide for the correct thread size, seat style, length, hex and torque specifications. You assume all liability of improper installation which can result in accident and/or injury.
• 1 year manufacturer warranty. Always check your vehicle fitment before purchasing! Contact cs@whtknight.com for warranty replacement or fitment issues.

$16.00 −$8.21 $7.79

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 6

White Knight 3809LBK-24AM Black Chrome M14x1.50 Duplex Spline Lug Nut with Key, 24 Pack

• For Select Aftermarket and Factory Wheels, replacement key adaptor is B07PY59X14 (3800L)
• Specifications: M14x1.50 Thread Pitch, 2.0” Overall Height, 0.90" Diameter, 7 Spline Drive, 60° Conical Seating, Duplex Spline Acorn.
• Features: Cold forged carbon steel and tested to industry standards. Durable construction with stylish chrome or black chrome finish. Utilizes 6 spline key adaptor for fast and secure installation
• ATTENTION: Refer to the owner’s manual or the wheel manufacturer’s guide for the correct thread size, seat style, length, hex and torque specifications. You assume all liability of improper installation which can result in accident and/or injury.
• 1 year manufacturer warranty. Always check your vehicle fitment before purchasing! Contact us for warranty replacement or fitment issues.

$29.99 −$5.00 $24.99

Buy on Amazon Price incl. tax, excl. shipping

Bestseller No. 7

White Knight 1304-1S-20AM Zinc 1/2"-20 Open-End Bulge Acorn Lug Nut, 20 Pack

• For Select Aftermarket or Factory Wheels or Wheels wih Hubcaps Covers
• 1/2"-20 Thread Pitch, 0.79” Overall Height, 0.90" Diameter, 3/4" Hex, 60° Conical Seating, Open-End Acorn.
• Features: Cold forged carbon steel and tested to industry standards. Durable construction, Stylish zinc finish. Utilizes traditional hex-body bulge-acorn design for fast and easy installation.
• ATTENTION: Refer to the owner’s manual or the wheel manufacturer’s guide for the correct thread size, seat style, length, hex and torque specifications. You assume all liability of improper installation which can result in accident and/or injury.
• 1 year manufacturer warranty. Always check your vehicle fitment before purchasing! Contact us for warranty replacement or fitment issues.

$14.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 8

Richeer 20pcs 1.4 inch Chrome 1/2-20 Closed End Bulge Acorn Lug Nuts - 3/4" 19mm Hex Wheel Lug Nut for Bronco Mustang Ranger Safari YJ TJ KJ KK ZJ WJ WK XK MJ XJ

• ★𝐒𝐩𝐞𝐜𝐢𝐟𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬: 1/2-20 thread - Closed End Bulge Acorn Style Lug Nuts - Conical 60 Degree Seat - 3/4(19mm) hex - 1.4 inch(35.56mm) long - 22.1mm wide.
• ★𝐅𝐢𝐭 𝐅𝐨𝐫: Compatible with vehicles requiring a 1/2-20 thread and wheels with a conical 60 degree seat with a 3/4" hex, including 1962-1984 DeVille, 1953-1978 Eldorado, 1977-1979 Seville, 1986-1997 Aerostar, 1966-1996 Bronco, 1975-2002 E-150 Econoline, 1991-2012 Explorer, 1975-1996 F150, 1965-2012 Mustang, 1974-2001 Cherokee, 1986-1992 Comanche, 2006-2010 Commander, 1993-2010 Grand Cherokee（only1/2), 2001-2013 Liberty, 1987- 2017 Wrangler and more. Important: They are not compatible with mag seat, ball seat, or round seat.
• ★𝐏𝐥𝐞𝐚𝐬𝐞 𝐍𝐨𝐭𝐞: Our lug nuts are designed for aftermarket wheels only and not work with factory OEM wheels. Recommend to use hand torque wrench instend of impact wrench. Any problem please contace us.
• ★𝐅𝐞𝐚𝐭𝐮𝐫𝐞𝐬: Our lug nuts are manufactured with SCM 435 cold forged steel and heat treated for maximum durability. Precisely machined threads ensure a perfect fit on your vehicle's wheel studs, while a special coating provides exceptional corrosion resistance and appearance.
• ★𝐒𝐞𝐫𝐯𝐢𝐜𝐞: Enjoy peace of mind with our 1-year warranty service. If there are any issues with our lug nuts, please contact us for free replacements, refunds, or other services to ensure customer satisfaction. Your satisfaction are our top priorities.

$21.99 −$4.00 $17.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 9

MIKKUPPA M14x1.5 Lug Nuts, Replacement for Silverado, Ford, GMC Aftermarket Wheel - 24pcs Chrome Closed End Bulge Acorn Lug Nuts

• 🚗【1.80" LONG】M14x1.5 thread - closed end bulge style lug nuts - conical 60 degree seat - 19mm hex - 1.80 in. long - 0.90 in. wide - color: Chrome. For Conical Required Wheel with 23mm Flange Limit Only. Do Not Capable for Wheel Caps.
• 🚗 【PERFECT FIT】Replacement for 2007-2013 Avalanche, 2015-2021 Colorado, 2003-2014 Express 1500, 1999-2021 Silverado 1500, 2015-2021 Suburban, 2000-2014 Suburban 1500, 1995-2020 Tahoe, 2009-2020 Traverse, 2007-2020 Acadia, 2015-2020 Canyon, 1999-2020 Sierra 1500, 2000-2020 Yukon, 2015-2020 F150/Expedition.
• 🚗【ONE-PIECE DESIGN】On vehicle testing, one-piece design compared with other two-piece design, Anti-cracking off and make it aesthetically pleasing while ensuring safe driving. Our products have undergone extensive on-vehicle testing to ensure proper fit and long-lasting performance before selling them.
• 🚗【ANTI-RUST PROCESS】The surface of the lug nut is chrome-plated, after 72 hours of strict salt spray test, which not only makes the nut resistant to oxygen and corrosion, but also gives the nut a bright visual impact. Using infrared drying technology, the paint is integrated with the metal and will Not fall off easily. Manufactured with high-quality SCM 435 Steel (Heat Treated) for stronger.
• 🚗【WORRY-FREE SHOPPING EXPERIENCE】If there is a problem with the number of missing nuts, please don't hesitate to contact us. Every MIKKUPPA product enjoys a 24-hour response, a 30-day unconditional refund and a 1 year warranty. Professional customer service promise to give you a satisfied solution.

$26.99 −$3.00 $23.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 10

SCITOO M12x1.25 Wheel Lug Bolt 12x1.25 Lug Nut Bolts 20 Pcs Silver Shank Length 28mm Compatible with for Jeep Compass for Renegade for Cherokee, for Fiat, for Chrysler 200, for Dodge Dart

• 🚙【WHEEL BOLT LUG NUTS COMPATIABLE VEHICLES】M12x1.25 wheel bolt compatible with 2017-2019 for Compass,2014-2023 for Cherokee,2015-2022 for Renegade, 2015-2017 for Chrysler 200, 2013-2016 for Dodge Dart, 2012-2017 for Fiat 500
• 🚙【FEARTURES】20 Pcs wheel bolts lug nuts are 12*1.25, shank length 28mm. Hex Size:17mm, Seat:Conical/60 grade 35CrMo Lug Nuts are Cold Forged/Exceeds OEM Quality
• 🚙【HIGH QUALITY】These M12x1.25 wheel studs lugs nuts are made from 35CrMo which have tested and meet or exceed OEM performance requirements
• 🚙【PLEASE CHECK】 Check your original thread pitch and seat type carefully, this only fit for M12x1.25 and conical/cone seat as shown
• 🚙【BUYING SERVICE】We provide ONE YEAR WARRANTY for our this product.If you have any questions about products, please feel free contact us, we will provide you with the most satisfactory solution

$39.98 −$11.00 $28.98

Buy on Amazon Price incl. tax, excl. shipping

Last update on 2024-06-12 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.