BC1200XL Wheel and Tire Assembly Replacement Kit – Vermeer

PRODUCT SAFETY ALERT

PURPOSE: Specific wheels (steel rim) with bolt pattern 8 on 6-1/2˝ (165 mm) circle to be used with 5/8˝ studs provided by a supplier:

• have an incorrect lug nut contact area causing wheel lug nuts to loosen and/or

• can develop possible cracks causing the tire to loose air

Both conditions may increase the risk of wheel loss and the risk of a crash. Death or serious injury is possible. Property damage may also occur. This kit provides the necessary parts and instructions to replace the wheel/tire assembly, install a new safety sign, a new wheel/tire specification placard decal and provides supplemental manuals.

SPECIAL TOOLS AND CONDITIONS:

• None

WARNING: Raised load can shift or fall. Death or serious injury could be possible if struck or crushed by falling load. Never allow anyone under a raised load unless load is securely supported to prevent it from shifting or falling.

WARNING: Failure to use shutdown procedure can result in unexpected hazard(s). Death or serious injury could result due to entanglement, crushing, cutting, or other hazardous contact. Follow Shutdown Procedure after operating, before performing any service or maintenance, and before transporting.

BC1200XL SHUTDOWN PROCEDURE

STOPPING THE MACHINE

NOTICE: For your safety and safety of others, use shutdown procedure before servicing, cleaning, unclogging, or transporting the chipper. A variation of this procedure may be used if so instructed within this document or if an emergency requires it.

1. Return Upper Feed Control Bar to center STOP position.1

2. Move Cutter Engage/Throttle Lever to ENGAGED/LOW RPM position.

NOTICE: Whenever practical and safe, allow engine to idle for 1–5 minutes before shutting down after operating at full power. Please consult machine’s engine manual for details.

3. Wait for cutter drum to slow.

4. Move Cutter Engage/Throttle Lever to DISENGAGED/LOW RPM position.

5. If so equipped, shut off remote control if in use.

6. Turn ignition key to OFF position and remove key.
17. Wait for the cutter drum and belt to stop.

NOTICE: Cutter drum rotation can be checked by looking at the end of shaft (1) on left side of cutter wheel housing. The cutter drum will continue to turn for a short time after the engine has stopped.

8. Close and latch feed table.

PROCEDURE: WHEELS, AXLES, AND SUSPENSION MAINTENANCE

WARNING: Incompatible lug nuts may loosen and cause wheel loss.

Use only 5/8-18 lug nuts with a 90° conical taper.

NOTICE: Improper or mismatched lug nuts and wheels can cause wheel loss leading to a crash. The conical taper of the lug nuts must properly engage the wheel lug nut seats.

The wheels and axle hubs on this trailer use special 5/8″-18 lug nuts with a 90° conical taper. Never use incompatible lug nuts, such as those with a 60° taper or a flat face.

Never use wheels intended for a 9/16″ wheel lugs.

Never use wheels that do not utilize a 90° conical lug nut seat taper.

WARNING: Incompatible wheels or loose lug nuts can cause wheel loss and machine damage.

Use only wheels that are compatible with 5/8 lug studs and 90° conical nuts. Check lug nut torque regularly.

Properly tighten lug nuts in a star pattern using only hand tools. DO NOT use impact wrenches which can damage the lug nuts, lug nut seats, and hub studs. Torque and check every 500 miles (800km).

WARNING: Improper tire pressure can cause a blowout..

Set cold tire pressure according to tire placard. Check pressure monthly.

NOTICE: Under-inflation causes tire damage and can lead to a blowout.

Set the tire air pressure to the value listed on the machine’s tire placard, NOT the pressure printed on the sidewall of the tire. Recheck monthly. Tires normally lose 1–2 psi (6.9–13.8 kPa) per month.

Tire pressure can also drop if the temperature outside has dropped significantly, so check more often in cold weather.

WARNING: Worn or damaged suspension can cause premature tire wear and machine damage.

Uneven wear on tires can be an indication of worn suspension or poor alignment.

NOTICE: Axle or suspension damage can cause pre-mature tire wear and tire failure, or axle failure.

Have your trailer checked if you suspect misalignment, if your tires have suffered any type of impact, or if you observe uneven tire wear.

WARNING: Avoid overloading or excess speed.

Follow manufacturer’s load and speed ratings.

NOTICE: High speed and overloading cause tire, axle, and suspension failure. DO NOT exceed the speed rating of the tires.

DO NOT exceed the load rating of the tires, axles, and suspension.

WARNING: Always use Vermeer authorized wheels, lug nuts, tires, and suspension components.

Improper or mismatched parts can lead to component failure, resulting in a crash.

PROCEDURE: 17.5 WHEEL AND TIRE ASSEMBLY ENGLISH MANUALS IK01

1. Using a suitable lifting device capable of lifting approximately 6,000 lb (2722 kg), raise machine off ground to allow adequate room to remove tire.

2. Place suitable blocking under trailer frame and remove lifting device.

3. Remove wheel, and 8 wheel nuts, from each side of Weight of each wheel is approximately 91 lb (42 kg).

4. Deflate tire or remove tire from wheel.

5. Torch cut wheels across the wheel nut area.

6. Take a photo(s) of destroyed wheels and attach to campaign warranty claim.

7. Discard wheel nuts so they can no longer be used or sold.

8. The removed used tires may be retained in your used tire inventory or disposed of. Cost of tire removal is included in labor hours.

9. Install supplied wheel assemblies (1), and clamp rings (2) on axle using 16 supplied wheel nuts (3). Weight of each wheel is approximately 91 lb (42 kg).Torque wheel nuts in a star pattern to 200 ft-lb (271 Nm).

10. Check to ensure tire pressure is 85 psi (590 kPa).

11. On the left side of the machine, apply new supplied wheel and tire warning decal (4) to the side of the metal fuel tank (machine equipped with gas engine), or to the side shield of the engine if machine is equipped with a plastic fuel tank (diesel engine).

12. On the right side of the machine, apply new supplied wheel and tire warning decal (4) and tire information decal (5) to the top of the fender.

13. Provide additional Supplemental Manual to owner.

14. Install Operator’s Manual with ring in manual storage box.

PROCEDURE: 17.5 WHEEL AND TIRE ASSEMBLY INTERNATIONAL IK02

1. Using a suitable lifting device capable of lifting approximately 6,000 lb (2722 kg), raise machine off ground to allow adequate room to remove tire.

2. Place suitable blocking under trailer frame and remove lifting device.

3. Remove wheel, and 8 wheel nuts, from each side of Weight of each wheel is approximately 91 lb (42 kg).

4. Deflate tire or remove tire from wheel.

5. Torch cut wheels across the wheel nut area.

6. Take a photo(s) of destroyed wheels and attach to campaign warranty claim.

7. Discard wheel nuts so they can no longer be used or sold.

8. The removed used tires may be retained in your used tire inventory or disposed of. Cost of tire removal is included in labor hours.

9. Install supplied wheel assemblies (1), and clamp rings (2) on axle using 16 supplied wheel nuts (3). Weight of each wheel is approximately 91 lb (42 kg).Torque wheel nuts in a star pattern to 200 ft-lb (271 Nm).

10. Check to ensure tire pressure is 85 psi (590 kPa).

11. On the left side of the machine, apply new supplied wheel and tire warning decal (4) to the side of the metal fuel tank (machine equipped with gas engine), or to the side shield of the engine if machine is equipped with a plastic fuel tank (diesel engine).

12. On the right side of the machine, apply new supplied wheel and tire warning decal (4) and tire information decal (5) to the top of the fender.

13. Provide additional Supplemental Manual to owner.

14. Install Operator’s Manual with ring in manual storage box.

PROCEDURE: SAFETY SIGN, TIRE SPECIFICATION PLACARD, MANUAL INSTALLATION IK03

1. Machines with wheel and tire assembly (PN 163759457) prevously installed must have new decals installed. On the left side of the machine, apply new supplied wheel and tire warning decal (1) to the side of the metal fuel tank (machine equipped with gas engine), or to the side shield of the engine if machine is equipped with a plastic fuel tank (diesel engine).

2. On the right side of the machine, apply new supplied wheel and tire warning decal (1) and tire information decal (2) to the top of the fender.
3. Provide additional Supplemental Manual to owner.
4. Install Operator’s Manual with ring in manual storage

PROCEDURE: SAFETY SIGN, TIRE SPECIFICATION PLACARD, MANUAL INSTALLATION IK04

1. On the left side of the machine, apply new supplied wheel and tire warning decal (1) to the side of the metal fuel tank (machine equipped with gas engine), or to the side shield of the engine if machine is equipped with a plastic fuel tank (diesel engine).
2. On the right side of the machine, apply new supplied wheel and tire warning decal (1) and tire information decal (2) to the top of the
3. Provide additional Supplemental Manual to owner.
4. Install Operator’s Manual with ring in manual storage box.

Remedy Instructions and TSB

RCRIT-20V085-9112.pdf 2191.068KB

Loading...

Taking too long?

Reload document

| Open in new tab

Download [2.09 MB]

Bestseller No. 1

12x1.5 Lug Nuts 20 Pcs Chrome Closed End Mag Style Lug Nuts with Washer 13/16" (21mm) Hex Compatible with Toyota Camry/Corolla/Tacoma Lexus

• One-piece Solid lug nuts feature durable design and provide perfect replacement for your Tacoma, 4Runner, Corolla, GX470
• Specifications: 12x1.5 Thread Pitch; 13/16'' (21mm) Hex; 1.49" (38mm) OAL; Closed End; Color: Chrome
• 10.9-grade Heat-treated premium steel construction, which offers better durability and strength.
• Replace Part # 9094201058, 9008017036, 90942-01058, 9008-17036, 9094201084
• One-piece lug nuts unlike OEM OEM Cap Construction lug nuts, which means Reeauto's Lug nuts will definitely not break apart like your TOYOTA, LEXUS stock lug nuts

$18.90

Buy on Amazon Price incl. tax, excl. shipping

Bestseller No. 2

MIKKUPPA M12x1.5 Lug Nuts - Replacement for 2006-2019 Ford Fusion, 2000-2019 Ford Focus, 2001-2019 Ford Escape Aftermarket Wheel - 20pcs Chrome Closed End Lug Nut

• 🚗 WE' RE DIFFERENT - MIKKUPPA innovative closed end bulge Lug Nuts design provides a safer and more reliable closed end nut than any other on the market. One-piece design compared with other two-piece design, Anti-cracking off and make it aesthetically pleasing while ensuring safe driving. 【This kit does not hold the wheel cover! ! !】
• 🚗 PERFECT FIT - Replacement for 2004-2019 Acura TSX. 2002-2019 Chevy Trailblazer, 2001-2019 Ford Escape, 2000-2019 Ford Focus, 2006-2019 Ford Fusion, 1999-2019 Honda Accord/CR-V, 2005-2019 KIA Sportage LX EX, 1995-2019 Toyota Avalon, etc.
• 🚗 SPECIFICATION - M12x1.5 thread - closed end bulge style lug nuts - conical 60 degree seat - 19mm hex - 35.05mm long - 22mm wide - color: silver / chrome. Our nuts have an innovative design in appearance due to personal preference, but the thread specifications fully meet vehicle standards, buy with confidence.
• 🚗 ONE-PIECE LUG NUTS - The one-piece structure design is more splendid and safer than the two-piece design. Triple chrome, cold forged and heat treated steel, anti-rusting and anti-stripped, high strength and durability.
• 🚗 WORRY-FREE SHOPPING EXPERIENCE - We go above and beyond to provide the highest quality wheel lug nut and top notch customer service. Contact us and we will give you a satisfactory answer within 24 hours. The 12-month warranty gives you a worry-free shopping experience.

$19.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 3

White Knight 1707S-20AM Chrome M12x1.50 Bulge Acorn Lug Nut, 20 Count (Pack of 1)

• For Select Aftermarket and Factory Wheels.
• Specifications: M12 x 1.50 Thread Pitch, 1.40” Overall Height, 0.90" Diameter, 3/4" Hex, 60° Conical Seating, Bulge Acorn.
• Features: Cold forged carbon steel and tested to industry standards. Durable construction. Stylish chrome or black chrome finish. Utilizes traditional hex-body bulge-acorn design for fast and easy installation.
• ATTENTION: Refer to the owner’s manual or the wheel manufacturer’s guide for the correct thread size, seat style, length, hex and torque specifications. You assume all liability of improper installation which can result in accident and/or injury.
• 1 year manufacturer warranty. Always check your vehicle fitment before purchasing! Contact us for warranty replacement or fitment issues.

$21.99 −$4.00 $17.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 4

Dorman 711-265 Wheel Nut Chrome Acorn Bulge Seat 1/2-20 Compatible with Select Models, 20 Pack, Medium

• Direct replacement - these wheel lug nuts are designed to match the fit, function and performance of the original equipment hardware on specified vehicles
• Ensure fit - available in a variety of sizes and assortments, please check product dimensions and details to ensure you select the right wheel lug nut(s) for your application
• Durable construction - designed and manufactured to strict specifications for reliable performance
• Trustworthy quality - backed by a team of product experts in the United States and more than a century of automotive experience
• Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool

$17.71 −$7.39 $10.32

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 5

White Knight Wheel Lug Nuts - 12x1.5 Lug Nuts, 1707S-4, 4 Pack, M12x1.50 Bulge Acorn Chrome Lug Nuts, Steel with Stylish Chrome Finish, Easy to Install, Durable Construction

• For Select Aftermarket and Factory Wheels.
• Specifications: M12 x 1.50 Thread Pitch, 1.40” Overall Height, 0.90" Diameter, 3/4" Hex, 60° Conical Seating, Bulge Acorn.
• Features: Cold forged carbon steel and tested to industry standards. Durable construction. Stylish chrome or black chrome finish. Utilizes traditional hex-body bulge-acorn design for fast and easy installation.
• ATTENTION: Refer to the owner’s manual or the wheel manufacturer’s guide for the correct thread size, seat style, length, hex and torque specifications. You assume all liability of improper installation which can result in accident and/or injury.
• 1 year manufacturer warranty. Always check your vehicle fitment before purchasing! Contact cs@whtknight.com for warranty replacement or fitment issues.

$16.00 −$8.21 $7.79

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 6

White Knight 3809LBK-24AM Black Chrome M14x1.50 Duplex Spline Lug Nut with Key, 24 Pack

• For Select Aftermarket and Factory Wheels, replacement key adaptor is B07PY59X14 (3800L)
• Specifications: M14x1.50 Thread Pitch, 2.0” Overall Height, 0.90" Diameter, 7 Spline Drive, 60° Conical Seating, Duplex Spline Acorn.
• Features: Cold forged carbon steel and tested to industry standards. Durable construction with stylish chrome or black chrome finish. Utilizes 6 spline key adaptor for fast and secure installation
• ATTENTION: Refer to the owner’s manual or the wheel manufacturer’s guide for the correct thread size, seat style, length, hex and torque specifications. You assume all liability of improper installation which can result in accident and/or injury.
• 1 year manufacturer warranty. Always check your vehicle fitment before purchasing! Contact us for warranty replacement or fitment issues.

$29.99 −$5.00 $24.99

Buy on Amazon Price incl. tax, excl. shipping

Bestseller No. 7

White Knight 1304-1S-20AM Zinc 1/2"-20 Open-End Bulge Acorn Lug Nut, 20 Pack

• For Select Aftermarket or Factory Wheels or Wheels wih Hubcaps Covers
• 1/2"-20 Thread Pitch, 0.79” Overall Height, 0.90" Diameter, 3/4" Hex, 60° Conical Seating, Open-End Acorn.
• Features: Cold forged carbon steel and tested to industry standards. Durable construction, Stylish zinc finish. Utilizes traditional hex-body bulge-acorn design for fast and easy installation.
• ATTENTION: Refer to the owner’s manual or the wheel manufacturer’s guide for the correct thread size, seat style, length, hex and torque specifications. You assume all liability of improper installation which can result in accident and/or injury.
• 1 year manufacturer warranty. Always check your vehicle fitment before purchasing! Contact us for warranty replacement or fitment issues.

$14.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 8

Richeer 20pcs 1.4 inch Chrome 1/2-20 Closed End Bulge Acorn Lug Nuts - 3/4" 19mm Hex Wheel Lug Nut for Bronco Mustang Ranger Safari YJ TJ KJ KK ZJ WJ WK XK MJ XJ

• ★𝐒𝐩𝐞𝐜𝐢𝐟𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬: 1/2-20 thread - Closed End Bulge Acorn Style Lug Nuts - Conical 60 Degree Seat - 3/4(19mm) hex - 1.4 inch(35.56mm) long - 22.1mm wide.
• ★𝐅𝐢𝐭 𝐅𝐨𝐫: Compatible with vehicles requiring a 1/2-20 thread and wheels with a conical 60 degree seat with a 3/4" hex, including 1962-1984 DeVille, 1953-1978 Eldorado, 1977-1979 Seville, 1986-1997 Aerostar, 1966-1996 Bronco, 1975-2002 E-150 Econoline, 1991-2012 Explorer, 1975-1996 F150, 1965-2012 Mustang, 1974-2001 Cherokee, 1986-1992 Comanche, 2006-2010 Commander, 1993-2010 Grand Cherokee（only1/2), 2001-2013 Liberty, 1987- 2017 Wrangler and more. Important: They are not compatible with mag seat, ball seat, or round seat.
• ★𝐏𝐥𝐞𝐚𝐬𝐞 𝐍𝐨𝐭𝐞: Our lug nuts are designed for aftermarket wheels only and not work with factory OEM wheels. Recommend to use hand torque wrench instend of impact wrench. Any problem please contace us.
• ★𝐅𝐞𝐚𝐭𝐮𝐫𝐞𝐬: Our lug nuts are manufactured with SCM 435 cold forged steel and heat treated for maximum durability. Precisely machined threads ensure a perfect fit on your vehicle's wheel studs, while a special coating provides exceptional corrosion resistance and appearance.
• ★𝐒𝐞𝐫𝐯𝐢𝐜𝐞: Enjoy peace of mind with our 1-year warranty service. If there are any issues with our lug nuts, please contact us for free replacements, refunds, or other services to ensure customer satisfaction. Your satisfaction are our top priorities.

$21.99 −$4.00 $17.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 9

MIKKUPPA M14x1.5 Lug Nuts, Replacement for Silverado, Ford, GMC Aftermarket Wheel - 24pcs Chrome Closed End Bulge Acorn Lug Nuts

• 🚗【1.80" LONG】M14x1.5 thread - closed end bulge style lug nuts - conical 60 degree seat - 19mm hex - 1.80 in. long - 0.90 in. wide - color: Chrome. For Conical Required Wheel with 23mm Flange Limit Only. Do Not Capable for Wheel Caps.
• 🚗 【PERFECT FIT】Replacement for 2007-2013 Avalanche, 2015-2021 Colorado, 2003-2014 Express 1500, 1999-2021 Silverado 1500, 2015-2021 Suburban, 2000-2014 Suburban 1500, 1995-2020 Tahoe, 2009-2020 Traverse, 2007-2020 Acadia, 2015-2020 Canyon, 1999-2020 Sierra 1500, 2000-2020 Yukon, 2015-2020 F150/Expedition.
• 🚗【ONE-PIECE DESIGN】On vehicle testing, one-piece design compared with other two-piece design, Anti-cracking off and make it aesthetically pleasing while ensuring safe driving. Our products have undergone extensive on-vehicle testing to ensure proper fit and long-lasting performance before selling them.
• 🚗【ANTI-RUST PROCESS】The surface of the lug nut is chrome-plated, after 72 hours of strict salt spray test, which not only makes the nut resistant to oxygen and corrosion, but also gives the nut a bright visual impact. Using infrared drying technology, the paint is integrated with the metal and will Not fall off easily. Manufactured with high-quality SCM 435 Steel (Heat Treated) for stronger.
• 🚗【WORRY-FREE SHOPPING EXPERIENCE】If there is a problem with the number of missing nuts, please don't hesitate to contact us. Every MIKKUPPA product enjoys a 24-hour response, a 30-day unconditional refund and a 1 year warranty. Professional customer service promise to give you a satisfied solution.

$26.99 −$3.00 $23.99

Buy on Amazon Price incl. tax, excl. shipping

SaleBestseller No. 10

SCITOO M12x1.25 Wheel Lug Bolt 12x1.25 Lug Nut Bolts 20 Pcs Silver Shank Length 28mm Compatible with for Jeep Compass for Renegade for Cherokee, for Fiat, for Chrysler 200, for Dodge Dart

• 🚙【WHEEL BOLT LUG NUTS COMPATIABLE VEHICLES】M12x1.25 wheel bolt compatible with 2017-2019 for Compass,2014-2023 for Cherokee,2015-2022 for Renegade, 2015-2017 for Chrysler 200, 2013-2016 for Dodge Dart, 2012-2017 for Fiat 500
• 🚙【FEARTURES】20 Pcs wheel bolts lug nuts are 12*1.25, shank length 28mm. Hex Size:17mm, Seat:Conical/60 grade 35CrMo Lug Nuts are Cold Forged/Exceeds OEM Quality
• 🚙【HIGH QUALITY】These M12x1.25 wheel studs lugs nuts are made from 35CrMo which have tested and meet or exceed OEM performance requirements
• 🚙【PLEASE CHECK】 Check your original thread pitch and seat type carefully, this only fit for M12x1.25 and conical/cone seat as shown
• 🚙【BUYING SERVICE】We provide ONE YEAR WARRANTY for our this product.If you have any questions about products, please feel free contact us, we will provide you with the most satisfactory solution

$39.98 −$11.00 $28.98

Buy on Amazon Price incl. tax, excl. shipping

Last update on 2024-06-12 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.