“This site contains affiliate links for which OEMDTC may be compensated” |
November 12, 2020 NHTSA CAMPAIGN NUMBER: 20V697000
Wheel Chair Belt Anchors May Fail/FMVSS 222
If the shoulder belt and ground anchors detach during a crash, their would be an increased risk of injury to the occupant.
NHTSA Campaign Number: 20V697
Manufacturer Lion Electric Company
Components SEAT BELTS
Potential Number of Units Affected 8
Summary
Lion Electric Company (Lion Electric) is recalling certain 2016-2019 Lion C and Lion 360 school buses equipped with wheelchair lifts. The shoulder belt and ground anchors intended to hold a wheelchair in place may detach in the event of a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 222, “School Bus Passenger Seating and Crash Protection.”
Remedy
Lion Electric has notified owners, and dealers will add a rivet to reinforce the floor and change the screws on the seat belt, free of charge. The recall began November 23, 2020. Owners may contact Lion Electric customer service at 1-855-546-6706.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
November 16 2020
Customer Address
The Lion Electric Co.
921 Chemin de la Rivière du Nord
Saint-Jérôme (Québec) J7Y 5G2
T (450) 432-5466 F (450) 592-7566
IMPORTANT SAFETY RECALL 20V697
This notice is sent to you in accordance with the requirements of the Motor Vehicle Safety Title 49, United States Code Chapter 301, administered by the National Highway Traffic Safety Administration. This is to inform you that your vehicle may contain a defect that could affect the safety of a person.
Description of the vehicle(s) affected by the defect
Make: Lion
Model: Lion C and Lion 360
Year: 2016-2019
Vehicle Identification Number (VIN): xxxxxxxxxxxxx
Recall number issued by NHTSA: 20V697
Description of the defect
The non-compliance that is the subject of this notice is in respect to shoulder belt anchors and ground anchors that allow the wheelchair to be held in place. In the event of an impact, the anchors and ground anchorages could detach, thereby compromising human safety. As a result of our certification tests on the shoulder belt anchorages and ground anchors, the anchorages do not resist the minimum force required, not meeting the FMVSS 222 standard section 5.4. The belt anchorage and ground attachment points could become detached, compromising passenger safety, increasing the chance of personal injury.
Corrective Measures
Lion Electric will contact you to determine the date of the intervention to make the necessary modifications to remedy the non-compliance. The company will assume the cost of this corrective action. We will reinforce the floor with the addition of rivet and change the screws on the seat belt. This operation takes about two hours.
Contact
For any question, do not hesitate to contact the service department at (450) 4325466 Ext. 229.
If you no longer own this trailer, please contact Lion to provide the new owner information. Lion will then contact the new owner.
If you are the lessor of this vehicle, please forward a copy of this notice to the lessee within 10 days to comply with federal regulations.
If after having attempted to take advantage of this recall you believe you have not been able to have your vehicle remedied without charge and within a reasonable amount of time, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., S.E., Washington, D.C. 20590 or call the toll-free vehicle safety hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov
Our priority is to provide you with a product of the highest quality and security levels at all time. We apologize for the inconvenience and thank you for your trust and valuable cooperation.
Quality director
SEOCONTENT-START
RETRO0057
1 of 5
Contremaître Leader
Date:
2020-11-25
Version:
00
Subject:
RETROFIT: RETRO – 0057
Year / Make / Models affected:
2016 -02019 Lion LionC/Lion360
NHTSA Recall#:
20V-697
Problem:
The seatbelt support for the wheelchair user are installed on the bow with metal screws. This is not acceptable because this type of screw is not certified. This procedure will show how to install the seat belt support on the bow with rivets.
Remedy:
The metal screw will be replaced with rivets.
Materials List :
# Lion
Description
Quantity
14810724
1/4” Rivet
5 per seatbelt
Tools list:
Description
Riveter
Cutting disk
« F » sized drill bit
Drill
RETRO0057
2 of 5
Contremaître Leader
Now, the support is at 62.75 in of the floor.
Drop down to 50 in
Bow cap cutting zone
RETRO0057
3 of 5
Contremaître Leader
We need to drop down the top of the support to 50 in of the floor.
1. Unscrew the seatbelt support from the wall.
2. We need to have the support directly in contact with the bow.
3. Use the template flat bar to cut the bow cap at the right place. (See the dimensions of the flat bar below)
4. Drop the template on the floor and center it with the bow cap. Make a rectangular cut as it is on the template.
5. Put the seatbelt support at the place we need to fix it and mark the 5 spots we need to drill.
6. Drill on the bow with a “F” sized drill bit.
7. Fix the support with FIVE ¼” rivets (PN: 14810724)
Drop down the top of the support to 50 in of the floor
RETRO0057
4 of 5
Contremaître Leader
8. Do the same with each wheelchair seatbelt.
Template’s dimension.
RETRO0057
5 of 5
Contremaître Leader
RETRO0057
Revision table :
REV
EPN #
DESCRIPTION
DATE
00
0617
Initial release
11-07-2019
Signatures table :
Title
Name
Signature
Date
Project responsable
Engineering
Service
Martin Drolet
Quality
Martin Lamarche
****************************************************************
RETRO0057
1 de 5
Contremaître Chef d’Équipe
Installation ancrage de ceinture sur bow
Les ancrages de ceinture de sécurité pour les occupants de chaise roulant sont fixés sur les bow à l’aide de metal screw, ce qui n’est pas acceptable puisque ce type de vis n’est pas certifié. Cette procédure démontre comment installer le support de ceinture sur les bows à l’aide de rivets.
Créer une liste de matériel : # Lion Description Quantité
14810724
Rivet 1/4″
5 par ceinture
Créer une liste des outils : Identifiant Description
A
Riveteuse
B
Disque à découper
C
Forêt « F »
D
Perceuse
RETRO0057
2 de 5
Contremaître Chef d’Équipe
Présentement, l’ancrage est à 62,75 po du plancher.
RETRO0057
3 de 5
Contremaître Chef d’Équipe
Il faut descendre le top du support à 50 po du plancher.
1. Déviser le support du mur.
2. Faire une découpe dans le bow cap intérieur pour que le support soit directement fixé sur le bow.
3. Utilisez le gabarit pour faire une découpe (3.5po X 0.75po) dans le centre du bow cap. (Voir les dimensions du flat bar plus bas)
4. Déposer la flat bar sur le plancher et enlignez la avec le centre du bow cap. Faites la découpe rectangulaire à l’aide d’un disque de découpe comme le gabarit l’indique.
5. Déposer le support de ceinture à l’emplacement de fixation et marquer les 5 endroits où il faut percer.
6. Percer avec un forêt F les bows.
7. Fixer le support avec 5 rivets ¼ (PN : 14810724)
Descendre le top du support à 50 po du sol
RETRO0057
4 de 5
Contremaître Chef d’Équipe
8. Faire la même méthode pour chaque support de ceinture de wheelchair.
Dimension de la flat bar qui sert de gabarit.
RETRO0057
5 de 5
Contremaître Chef d’Équipe
Table des révisions :
REV
EPN #
DESCRIPTION
DATE
00
0617
Version initiale
11-07-2019
Table de signatures :
Poste
Nom
Signature
Date
Chargé de projet
Maxime Dupras
Approbation Ingénierie
Maxime Dupras
Approbation Service
Martin Drolet
Approbation Qualité
Martin Lamarche
RETRO0057
6 de 5
Contremaître Chef d’Équipe
Seatbelt support install on bow
The seatbelt support for the wheelchair user are installed on the bow with metal screws. This is not acceptable because this type of screw is not certified. This procedure will show how to install the seat belt support on the bow with rivets.
Materials List : # Lion Description Quantity
14810724
1/4” Rivet
5 per seatbelt
Tools list: Description
Riveter
Cutting disk
« F » sized drill bit
Drill
RETRO0057
7 de 5
Contremaître Chef d’Équipe
Now, the support is at 62.75 in of the floor.
Drop down to 50 in
Bow cap cutting zone
RETRO0057
8 de 5
Contremaître Chef d’Équipe
We need to drop down the top of the support to 50 in of the floor.
1. Unscrew the seatbelt support from the wall.
2. We need to have the support directly in contact with the bow.
3. Use the template flat bar to cut the bow cap at the right place. (See the dimensions of the flat bar below)
4. Drop the template on the floor and center it with the bow cap. Make a rectangular cut as it is on the template.
5. Put the seatbelt support at the place we need to fix it and mark the 5 spots we need to drill.
6. Drill on the bow with a “F” sized drill bit.
7. Fix the support with FIVE ¼” rivets (PN: 14810724)
8. Do the same with each wheelchair seatbelt.
Drop down the top of the support to 50 in of the floor
RETRO0057
9 de 5
Contremaître Chef d’Équipe
Template’s dimension.
RETRO0057
10 de 5
Contremaître Chef d’Équipe
RETRO0057
Revision table :
REV
EPN #
DESCRIPTION
DATE
00
0617
Initial release
11-07-2019
Signatures table :
Title
Name
Signature
Date
Project responsable
Engineering
Service
Martin Drolet
Quality
Martin Lamarche
***************************************************************
RETRO0095-N/A-EPN0713-00 Rev : 01 RETROFIT Page 1 of 5
RETROFIT
WHEELCHAIR LIFT FLOOR REINFORCEMENT
RETROFIT: RETRO – 0095
Instruction: N/A
EPN:0713-00
Date:
2020-11-25
Version:
01
Subject:
RETROFIT: RETRO – 0095
Year / Make / Models affected:
2016 -02019 Lion LionC/Lion360
NHTSA Recall#:
20V-697
Problem:
The wheelchair anchors had torn the floor beam when we passed the CMVSS 222.
Remedy:
Structural rivets need to be added to stiffener the beam and pass the CMVSS 222.
RETRO0095-N/A-EPN0713-00 Rev : 01 WHEELCHAIR LIFT FLOOR REINFORCEMENT Page 2 of 5
VALIDATION REVISION: 01
Engineering Manager
Service Manager
Quality Manager
Maxime Dupras
Mykaël Lemelin
Guy Lecompte
Table of Contents
LISTE OF EQUIPMENT: ……………………………………………………………………………………………………………………………….. 3
LISTE OF TOOLS : ………………………………………………………………………………………………………………………………………. 3
1. FLOOR REINFORCEMENT………………………………………………………………………………………………………………………… 4
RELEVANT MANAGER ………………………………………………………………………………………………………………………………… 5
REVISION HISTORY ……………………………………………………………………………………………………………………………………. 5
RETRO0095-N/A-EPN0713-00 Rev : 01 WHEELCHAIR LIFT FLOOR REINFORCEMENT Page 3 of 5
LISTE OF EQUIPMENT:
Option 1 (Rivet):
Lion PN
Description
Quantity
14810730
Rivet Huck Magna Bulb, Steel Zinc, ID 1/4″, Grip R 0,229-0,308” Code Dark Green
112
Option 2 (Bolt and Nut):
Lion PN
Description
Quantity
14802478
Hex flanged bolt, 3/8-16 X 1 in, zinc clear, G5
112
14800516
Hex flanged lock nut, 3/8-16, zinc clear, G5, Nylon insert
112
LISTE OF TOOLS :
Option 1 (Rivet):
Item
Description
Image
A
Drill 90⁰
B
Drill bit F
C
90⁰ riveter 1/4
Option 2 (Bolt and Nut):
Item
Description
Image
A
Drill 90⁰
B
Drill bit 25/64’’
C
Socket ½’’
RETRO0095-N/A-EPN0713-00 Rev : 01 WHEELCHAIR LIFT FLOOR REINFORCEMENT Page 4 of 5
1. FLOOR REINFORCEMENT
If necessary, remove the heating system :
1. Remove exhaust from under the unit
2. Remove coolant hose (2)
3. Remove diesel lines (2)
4. Remove electrical connector (5)
5. Remove the system form his brackets
Option 1 (Rivet):
A
Drill 16 holes with drill bit F at the locations identified by red dots and arrows and at 1 11/32’’ from the bottom of the C channel. The blue dots represent the rivets already on the C channel.
B
Install 16 1/4 rivets (14810730) on each C channel (7) behind the wheelhouses.
Option 2 (Bolt and Nut):
A
Drill 16 holes with drill bit 25/64’’ at the locations identified by red dots and arrows and at 1 11/32’’ from the bottom of the C channel. The blue dots represent the rivets already on the C channel.
B
Install 16 bolts 3/8-16 (14802478) and nuts 3/8-16 (14800516) on each C channel (10) identified below. Apply a torque of 31 ft-lbs in dry condition.
OPTION 1
14810730 (16x) on each C channel
OPTION 2
14802478 (16x) and 14800516 (16x) on each C channel
A/B
A
Black holes are for the skirts
Black holes are for the skirts
RETRO0095-N/A-EPN0713-00 Rev : 01 WHEELCHAIR LIFT FLOOR REINFORCEMENT Page 5 of 5
Relevant Manager
Name
Email
Title
Comments
Noel Filho
noel.filho@thelionelectric.com
Tech. Genie Mécanique
Maxime Dupras
maxime.dupras@thelionelectric.com
Lead engineer – MFG
Revision History
Rev 00 – 22-06-20 Révision Initiale
Rev 01 – 14-08-20 Add six (6) holes and rivets/bolts to the floor’s C channels
*****************************************************************************************
RETRO0095-N/A-EPN0713-00 Rev : 01 RETROFIT Page 1 of 10
RETROFIT
RENFORCEMENT PLANCHER WHEELCHAIR LIFT 1, 2 OU 3 CHAISES ROULANTES
RETROFIT: RETRO – 0095
Instruction: N/A
EPN:0713-00
VALIDATION REVISION: 01 Responsable Ingénierie Responsable Service Responsable Qualité
Maxime Dupras
Mykaël Lemelin
Guy Lecompte
RETRO0095-N/A-EPN0713-00 Rev : 01 RENFORCEMENT PLANCHER WHEELCHAIR LIFT
1, 2 OU 3 CHAISES ROULANTES Page 2 of 10
Table des matières
LISTE DE MATÉRIEL: …………………………………………………………………………………………………………………………………… 3
LISTE DES OUTILS : …………………………………………………………………………………………………………………………………….. 3
1. RENFORCEMENT DU PLANCHER ………………………………………………………………………………………………………………. 4
RESPONSABLE CONCERNÉ ………………………………………………………………………………………………………………………….. 5
HISTORIQUE DES RÉVISIONS ……………………………………………………………………………………………………………………….. 5
RETRO0095-N/A-EPN0713-00 Rev : 01 RENFORCEMENT PLANCHER WHEELCHAIR LIFT
1, 2 OU 3 CHAISES ROULANTES Page 3 of 10
LISTE DE MATÉRIEL:
Option 1 (Rivet): Lion PN Description Quantité
14810730
Rivet Huck Magna Bulb, Steel Zinc, ID 1/4″, Grip R 0,229-0,308” Code Dark Green
112
Option 2 (Écrou et noix): Lion PN Description Quantité
14802478
Hex flanged bolt, 3/8-16 X 1 in, zinc clear, G5
112
14800516
Hex flanged lock nut, 3/8-16, zinc clear, G5, Nylon insert
112
LISTE DES OUTILS :
Option 1 (Rivet): Identifiant Description Image
A
Perceuse 90⁰
B
Foret F
C
Riveteuse 1/4
Option 2 (Écrou et noix): Identifiant Description Image
A
Perceuse 90⁰
B
Foret 25/64
C
Douille 1/2
RETRO0095-N/A-EPN0713-00 Rev : 01 RENFORCEMENT PLANCHER WHEELCHAIR LIFT
1, 2 OU 3 CHAISES ROULANTES Page 4 of 10
1. RENFORCEMENT DU PLANCHER Si nécessaire, retirer le système de chauffage : 1. Retirer l’exhaust de sous l’unité 2. Retirer les tuyaux (2) (coolant) 3. Retirer les lignes (2) de diesel 4. Retirer les connecteurs électriques (5) 5. Retirer le système de sur son support
Option 1 : A Percer 16 trous avec un foret F aux emplacements identifiés par des points et flèches rouges ci-dessous, à 1 11/32 po du bas du C channel. Les points bleus représentent les rivets déjà existants.
B
Installer 16 rivets 1/4 (14810730) sur chaque C channel (7) qui se trouvent derrière les wheelhouse. Option 2 :
A
Percer 16 trous avec un foret 25/64’’ aux emplacements identifiés par des points et flèches rouges ci-dessous, à 1 11/32 po du bas du C channel. Les points bleus représentent les rivets déjà existants. B Installer 16 boulons 3/8-16 (14802478) et écrous 3/8-16 (14800516) et appliquez un torque de 31 lbs-pi à sec sur chaque C channel (7) qui se trouvent derrière les wheelhouse.
OPTION 1
14810730 (16x) sur chaque C channel
A
A/B
OPTION 2
14802478 (16x) et 14800516 (16x) sur chaque C channel
Trous noirs pour les skirts
Trous noirs pour les skirts
RETRO0095-N/A-EPN0713-00 Rev : 01 RENFORCEMENT PLANCHER WHEELCHAIR LIFT
1, 2 OU 3 CHAISES ROULANTES Page 5 of 10
Responsable concerné Nom Courriel Titre Commentaires
Noel Filho
noel.filho@thelionelectric.com
Tech. Genie Mécanique
Maxime Dupras
maxime.dupras@thelionelectric.com
Lead engineer – MFG
Historique des révisions
Rev 00 – 22-06-20 Révision Initiale
Rev 01 – 14-08-20 Ajout de six (6) trous et rivet/boulon aux C channels du plancher.
RETRO0095-N/A-EPN0713-00 Rev : 01 RETROFIT Page 6 of 10
RETROFIT
WHEELCHAIR LIFT FLOOR REINFORCEMENT
1, 2 OR 3 WHEELCHAIRS
RETROFIT: RETRO – 0095
Instruction: N/A
EPN:0713-00
VALIDATION REVISION: 01 Engineering Manager Service Manager Quality Manager
Maxime Dupras
Mykaël Lemelin
Guy Lecompte
RETRO0095-N/A-EPN0713-00 Rev : 01 1, 2 OR 3 WHEELCHAIRS Page 7 of 10
Table of Contents
LISTE OF EQUIPMENT:………………………………………………………………………………………………………………………………… 8
LISTE OF TOOLS : ……………………………………………………………………………………………………………………………………….. 8
1. FLOOR REINFORCEMENT ………………………………………………………………………………………………………………………… 9
RELEVANT MANAGER ………………………………………………………………………………………………………………………………. 10
REVISION HISTORY …………………………………………………………………………………………………………………………………… 10
RETRO0095-N/A-EPN0713-00 Rev : 01 1, 2 OR 3 WHEELCHAIRS Page 8 of 10
LISTE OF EQUIPMENT:
Option 1 (Rivet): Lion PN Description Quantity
14810730
Rivet Huck Magna Bulb, Steel Zinc, ID 1/4″, Grip R 0,229-0,308” Code Dark Green
112
Option 2 (Bolt and Nut): Lion PN Description Quantity
14802478
Hex flanged bolt, 3/8-16 X 1 in, zinc clear, G5
112
14800516
Hex flanged lock nut, 3/8-16, zinc clear, G5, Nylon insert
112
LISTE OF TOOLS :
Option 1 (Rivet): Item Description Image
A
Drill 90⁰
B
Drill bit F
C
90⁰ riveter 1/4
Option 2 (Bolt and Nut): Item Description Image
A
Drill 90⁰
B
Drill bit 25/64’’
C
Socket ½’’
RETRO0095-N/A-EPN0713-00 Rev : 01 1, 2 OR 3 WHEELCHAIRS Page 9 of 10
1. FLOOR REINFORCEMENT If necessary, remove the heating system: 1. Remove exhaust from under the unit 2. Remove coolant hose (2) 3. Remove diesel lines (2) 4. Remove electrical connector (5) 5. Remove the system form his brackets
Option 1 (Rivet): A Drill 16 holes with drill bit F at the locations identified by red dots and arrows and at 1 11/32’’ from the bottom of the C channel. The blue dots represent the rivets already on the C channel.
B
Install 16 1/4 rivets (14810730) on each C channel (7) behind the wheelhouses. Option 2 (Bolt and Nut):
A
Drill 16 holes with drill bit 25/64’’ at the locations identified by red dots and arrows and at 1 11/32’’ from the bottom of the C channel. The blue dots represent the rivets already on the C channel. B Install 16 bolts 3/8-16 (14802478) and nuts 3/8-16 (14800516) on each C channel (10) identified below. Apply a torque of 31 ft-lbs in dry condition.
OPTION 1
14810730 (16x) on each C channel
OPTION 2
14802478 (16x) and 14800516 (16x) on each C channel
A/B
A
Black holes are for the skirts
Black holes are for the skirts
RETRO0095-N/A-EPN0713-00 Rev : 01 1, 2 OR 3 WHEELCHAIRS Page 10 of 10
Relevant Manager Name Email Title Comments
Noel Filho
noel.filho@thelionelectric.com
Tech. Genie Mécanique
Maxime Dupras
maxime.dupras@thelionelectric.com
Lead engineer – MFG
Revision History
Rev 00 – 22-06-20 Révision Initiale
Rev 01 – 14-08-20 Add six (6) holes and rivets/bolts to the floor’s C channels
**********************************************************************************************************************
RETRO0095-N/A-EPN0713-00 Rev : 01 RETROFIT Page 1 of 5
RETROFIT
WHEELCHAIR LIFT FLOOR REINFORCEMENT
RETROFIT: RETRO – 0095
Instruction: N/A
EPN:0713-00
Date:
2020-11-25
Version:
01
Subject:
RETROFIT: RETRO – 0095
Year / Make / Models affected:
2016 -02019 Lion LionC/Lion360
NHTSA Recall#:
20V-697
Problem:
The wheelchair anchors had torn the floor beam when we passed the CMVSS 222.
Remedy:
Structural rivets need to be added to stiffener the beam and pass the CMVSS 222.
RETRO0095-N/A-EPN0713-00 Rev : 01 WHEELCHAIR LIFT FLOOR REINFORCEMENT Page 2 of 5
VALIDATION REVISION: 01
Engineering Manager
Service Manager
Quality Manager
Maxime Dupras
Mykaël Lemelin
Guy Lecompte
Table of Contents
LISTE OF EQUIPMENT: ……………………………………………………………………………………………………………………………….. 3
LISTE OF TOOLS : ………………………………………………………………………………………………………………………………………. 3
1. FLOOR REINFORCEMENT………………………………………………………………………………………………………………………… 4
RELEVANT MANAGER ………………………………………………………………………………………………………………………………… 5
REVISION HISTORY ……………………………………………………………………………………………………………………………………. 5
RETRO0095-N/A-EPN0713-00 Rev : 01 WHEELCHAIR LIFT FLOOR REINFORCEMENT Page 3 of 5
LISTE OF EQUIPMENT:
Option 1 (Rivet):
Lion PN
Description
Quantity
14810730
Rivet Huck Magna Bulb, Steel Zinc, ID 1/4″, Grip R 0,229-0,308” Code Dark Green
112
Option 2 (Bolt and Nut):
Lion PN
Description
Quantity
14802478
Hex flanged bolt, 3/8-16 X 1 in, zinc clear, G5
112
14800516
Hex flanged lock nut, 3/8-16, zinc clear, G5, Nylon insert
112
LISTE OF TOOLS :
Option 1 (Rivet):
Item
Description
Image
A
Drill 90⁰
B
Drill bit F
C
90⁰ riveter 1/4
Option 2 (Bolt and Nut):
Item
Description
Image
A
Drill 90⁰
B
Drill bit 25/64’’
C
Socket ½’’
RETRO0095-N/A-EPN0713-00 Rev : 01 WHEELCHAIR LIFT FLOOR REINFORCEMENT Page 4 of 5
1. FLOOR REINFORCEMENT
If necessary, remove the heating system :
1. Remove exhaust from under the unit
2. Remove coolant hose (2)
3. Remove diesel lines (2)
4. Remove electrical connector (5)
5. Remove the system form his brackets
Option 1 (Rivet):
A
Drill 16 holes with drill bit F at the locations identified by red dots and arrows and at 1 11/32’’ from the bottom of the C channel. The blue dots represent the rivets already on the C channel.
B
Install 16 1/4 rivets (14810730) on each C channel (7) behind the wheelhouses.
Option 2 (Bolt and Nut):
A
Drill 16 holes with drill bit 25/64’’ at the locations identified by red dots and arrows and at 1 11/32’’ from the bottom of the C channel. The blue dots represent the rivets already on the C channel.
B
Install 16 bolts 3/8-16 (14802478) and nuts 3/8-16 (14800516) on each C channel (10) identified below. Apply a torque of 31 ft-lbs in dry condition.
OPTION 1
14810730 (16x) on each C channel
OPTION 2
14802478 (16x) and 14800516 (16x) on each C channel
A/B
A
Black holes are for the skirts
Black holes are for the skirts
RETRO0095-N/A-EPN0713-00 Rev : 01 WHEELCHAIR LIFT FLOOR REINFORCEMENT Page 5 of 5
Relevant Manager
Name
Email
Title
Comments
Noel Filho
noel.filho@thelionelectric.com
Tech. Genie Mécanique
Maxime Dupras
maxime.dupras@thelionelectric.com
Lead engineer – MFG
Revision History
Rev 00 – 22-06-20 Révision Initiale
Rev 01 – 14-08-20 Add six (6) holes and rivets/bolts to the floor’s C channels
**********************************************************************************************************************
RETRO0095-N/A-EPN0713-00 Rev : 01 RETROFIT Page 1 of 10
RETROFIT
RENFORCEMENT PLANCHER WHEELCHAIR LIFT 1, 2 OU 3 CHAISES ROULANTES
RETROFIT: RETRO – 0095
Instruction: N/A
EPN:0713-00
VALIDATION REVISION: 01 Responsable Ingénierie Responsable Service Responsable Qualité
Maxime Dupras
Mykaël Lemelin
Guy Lecompte
RETRO0095-N/A-EPN0713-00 Rev : 01 RENFORCEMENT PLANCHER WHEELCHAIR LIFT
1, 2 OU 3 CHAISES ROULANTES Page 2 of 10
Table des matières
LISTE DE MATÉRIEL: …………………………………………………………………………………………………………………………………… 3
LISTE DES OUTILS : …………………………………………………………………………………………………………………………………….. 3
1. RENFORCEMENT DU PLANCHER ………………………………………………………………………………………………………………. 4
RESPONSABLE CONCERNÉ ………………………………………………………………………………………………………………………….. 5
HISTORIQUE DES RÉVISIONS ……………………………………………………………………………………………………………………….. 5
RETRO0095-N/A-EPN0713-00 Rev : 01 RENFORCEMENT PLANCHER WHEELCHAIR LIFT
1, 2 OU 3 CHAISES ROULANTES Page 3 of 10
LISTE DE MATÉRIEL:
Option 1 (Rivet): Lion PN Description Quantité
14810730
Rivet Huck Magna Bulb, Steel Zinc, ID 1/4″, Grip R 0,229-0,308” Code Dark Green
112
Option 2 (Écrou et noix): Lion PN Description Quantité
14802478
Hex flanged bolt, 3/8-16 X 1 in, zinc clear, G5
112
14800516
Hex flanged lock nut, 3/8-16, zinc clear, G5, Nylon insert
112
LISTE DES OUTILS :
Option 1 (Rivet): Identifiant Description Image
A
Perceuse 90⁰
B
Foret F
C
Riveteuse 1/4
Option 2 (Écrou et noix): Identifiant Description Image
A
Perceuse 90⁰
B
Foret 25/64
C
Douille 1/2
RETRO0095-N/A-EPN0713-00 Rev : 01 RENFORCEMENT PLANCHER WHEELCHAIR LIFT
1, 2 OU 3 CHAISES ROULANTES Page 4 of 10
1. RENFORCEMENT DU PLANCHER Si nécessaire, retirer le système de chauffage : 1. Retirer l’exhaust de sous l’unité 2. Retirer les tuyaux (2) (coolant) 3. Retirer les lignes (2) de diesel 4. Retirer les connecteurs électriques (5) 5. Retirer le système de sur son support
Option 1 : A Percer 16 trous avec un foret F aux emplacements identifiés par des points et flèches rouges ci-dessous, à 1 11/32 po du bas du C channel. Les points bleus représentent les rivets déjà existants.
B
Installer 16 rivets 1/4 (14810730) sur chaque C channel (7) qui se trouvent derrière les wheelhouse. Option 2 :
A
Percer 16 trous avec un foret 25/64’’ aux emplacements identifiés par des points et flèches rouges ci-dessous, à 1 11/32 po du bas du C channel. Les points bleus représentent les rivets déjà existants. B Installer 16 boulons 3/8-16 (14802478) et écrous 3/8-16 (14800516) et appliquez un torque de 31 lbs-pi à sec sur chaque C channel (7) qui se trouvent derrière les wheelhouse.
OPTION 1
14810730 (16x) sur chaque C channel
A
A/B
OPTION 2
14802478 (16x) et 14800516 (16x) sur chaque C channel
Trous noirs pour les skirts
Trous noirs pour les skirts
RETRO0095-N/A-EPN0713-00 Rev : 01 RENFORCEMENT PLANCHER WHEELCHAIR LIFT
1, 2 OU 3 CHAISES ROULANTES Page 5 of 10
Responsable concerné Nom Courriel Titre Commentaires
Noel Filho
noel.filho@thelionelectric.com
Tech. Genie Mécanique
Maxime Dupras
maxime.dupras@thelionelectric.com
Lead engineer – MFG
Historique des révisions
Rev 00 – 22-06-20 Révision Initiale
Rev 01 – 14-08-20 Ajout de six (6) trous et rivet/boulon aux C channels du plancher.
RETRO0095-N/A-EPN0713-00 Rev : 01 RETROFIT Page 6 of 10
RETROFIT
WHEELCHAIR LIFT FLOOR REINFORCEMENT
1, 2 OR 3 WHEELCHAIRS
RETROFIT: RETRO – 0095
Instruction: N/A
EPN:0713-00
VALIDATION REVISION: 01 Engineering Manager Service Manager Quality Manager
Maxime Dupras
Mykaël Lemelin
Guy Lecompte
RETRO0095-N/A-EPN0713-00 Rev : 01 1, 2 OR 3 WHEELCHAIRS Page 7 of 10
Table of Contents
LISTE OF EQUIPMENT:………………………………………………………………………………………………………………………………… 8
LISTE OF TOOLS : ……………………………………………………………………………………………………………………………………….. 8
1. FLOOR REINFORCEMENT ………………………………………………………………………………………………………………………… 9
RELEVANT MANAGER ………………………………………………………………………………………………………………………………. 10
REVISION HISTORY …………………………………………………………………………………………………………………………………… 10
RETRO0095-N/A-EPN0713-00 Rev : 01 1, 2 OR 3 WHEELCHAIRS Page 8 of 10
LISTE OF EQUIPMENT:
Option 1 (Rivet): Lion PN Description Quantity
14810730
Rivet Huck Magna Bulb, Steel Zinc, ID 1/4″, Grip R 0,229-0,308” Code Dark Green
112
Option 2 (Bolt and Nut): Lion PN Description Quantity
14802478
Hex flanged bolt, 3/8-16 X 1 in, zinc clear, G5
112
14800516
Hex flanged lock nut, 3/8-16, zinc clear, G5, Nylon insert
112
LISTE OF TOOLS :
Option 1 (Rivet): Item Description Image
A
Drill 90⁰
B
Drill bit F
C
90⁰ riveter 1/4
Option 2 (Bolt and Nut): Item Description Image
A
Drill 90⁰
B
Drill bit 25/64’’
C
Socket ½’’
RETRO0095-N/A-EPN0713-00 Rev : 01 1, 2 OR 3 WHEELCHAIRS Page 9 of 10
1. FLOOR REINFORCEMENT If necessary, remove the heating system: 1. Remove exhaust from under the unit 2. Remove coolant hose (2) 3. Remove diesel lines (2) 4. Remove electrical connector (5) 5. Remove the system form his brackets
Option 1 (Rivet): A Drill 16 holes with drill bit F at the locations identified by red dots and arrows and at 1 11/32’’ from the bottom of the C channel. The blue dots represent the rivets already on the C channel.
B
Install 16 1/4 rivets (14810730) on each C channel (7) behind the wheelhouses. Option 2 (Bolt and Nut):
A
Drill 16 holes with drill bit 25/64’’ at the locations identified by red dots and arrows and at 1 11/32’’ from the bottom of the C channel. The blue dots represent the rivets already on the C channel. B Install 16 bolts 3/8-16 (14802478) and nuts 3/8-16 (14800516) on each C channel (10) identified below. Apply a torque of 31 ft-lbs in dry condition.
OPTION 1
14810730 (16x) on each C channel
OPTION 2
14802478 (16x) and 14800516 (16x) on each C channel
A/B
A
Black holes are for the skirts
Black holes are for the skirts
RETRO0095-N/A-EPN0713-00 Rev : 01 1, 2 OR 3 WHEELCHAIRS Page 10 of 10
Relevant Manager Name Email Title Comments
Noel Filho
noel.filho@thelionelectric.com
Tech. Genie Mécanique
Maxime Dupras
maxime.dupras@thelionelectric.com
Lead engineer – MFG
Revision History
Rev 00 – 22-06-20 Révision Initiale
Rev 01 – 14-08-20 Add six (6) holes and rivets/bolts to the floor’s C channels
8 Affected Products
Vehicles
MAKE | MODEL | YEAR |
LION | 360 | 2016-2019 |
LION | LION C | 2016-2019 |
11 Associated Documents
Remedy Instructions and TSB
RCRIT-20V697-7413.pdf 546.003KB
Remedy Instructions and TSB
RCRIT-20V697-0785.pdf 458.197KB
Noncompliance Notice 573 Report
RCLRPT-20V697-3752.PDF 213.706KB
Recall Quarterly Report #1, 2020-4
RCLQRT-20V697-3426.PDF 211.134KB
Remedy Instructions and TSB
RCRIT-20V697-7807.pdf 617.042KB
Recall Acknowledgement
RCAK-20V697-3122.pdf 244.779KB
Owner Notification Letter(Part 577)
RCONL-20V697-3604.pdf 93.716KB
Remedy Instructions and TSB
RCRIT-20V697-6114.pdf 436.06KB
Recall 573 Report- Amendment 1
RCLRPT-20V697-4980.PDF 214.043KB
Recall 573 Report- Amendment 2
RCLRPT-20V697-6623.PDF 214.117KB
Recall Quarterly Report #3, 2021-2
RCLQRT-20V697-9858.PDF 211.312KB
Latest Recalls Documents
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V697&docType=RCL
- 【Easy to Use--Work out of box】+【FOXWELL 2024 New Version】 FOXWELL NT604 Elite scan tool is the 2024 new version from FOXWELL, which is designed for those car owners who want to figure out the cause issue before fixing the car problem via scanning the most common systems like abs srs engine and transmission.The NT604 Elite diagnostic tool comes with latest software, which can be used out of box. No need to waste time to download the software first.
- 【Affordable】+【Reliable Car Health Monitor】 Will you be confused what happen when the warning light of abs/srs/transmission/check engine flashes? Instead of taking your cars to dealership, this foxwell scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. It will t-urn off the warning light car after the problem is fixed.👉TIPS: Airbag crash/collision data can NOT be cleared even you replace the new airbag.
- 【5 in 1 Diagnostic Scanner】Compared with those auto scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also it can be an abs/srs scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it.
- 【Fantastic AUTOVIN】+【No extra software fee】Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite abs srs scanner supports 60+ car makes from worldwide (America/Asia/Europe). You don’t need to pay extra software fee.
- 【Solid protective case KO plastic carrying bag】+ 【Lifetime update】Almost all same price-level obd scanner diagnostic tool only offers plastic bag to hold on the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- 🎉【2024 Upgraded Ver. of AL519/ ML519/ ML619】Autel develops the brand-new AutoLink AL619 as the advanced ver. of Autel ML519, AL519, AL319, MS309. This AL619 OBD2 scanner can scan ABS & SRS systems, and support 10 Modes of OBD II Diagnostics Function on Worldwide Vehicles to read, erase codes and turn off the MIL, ABS, SRS warning lights so that you can better maintain your car when related malfunctions occur and make your vehicle ready for the annual test.
- 🎉【Accurate ABS/ SRS Diagnostics Functions】The ABS/ SRS diagnostic function is used to retrieve and clear codes from the ABS/ SRS systems. It can read and clear DTCs, show definitions of each code, display live data of multiple sensors in the graph to locate fault causes, and assist home mechanics to do the proper repair and clear ABS & Airbag warning lights. Diagnoses ABS/ SRS system codes on most 1996 and newer major vehicle models. Please email 📩 immoautel @ outlook. com 📩 for help.
- 🎉【All 10 Modes of OBD II Diagnostics Function】The OBD II Diagnostics function is a fast-access option that allows you to carry out a quick test on the engine system of OBD II vehicles. Read Codes, Erase Codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, DTC Lookup, Component Test, Viewing Vehicle Information, Modules Present.
- 🎉【Live Data and Freeze Frame Data】With Live Data functions, Autel AL619 OBD2 diagnostic code reader allows you to view the live PID (Parameter Identification Data) of the vehicle's computer module(s) in text, graph to check the status of various sensors. And Freeze Frame Data enables you to view the vehicle's operating parameters at the moment a DTC is detected. These information will aid the technician by allowing the parameters to be duplicated for diagnostic and repair purposes.
- 🎉【DTC Lookup Feature】Besides showing you the code’s definition while you are reading the diagnostic trouble codes, AL619 features comparably user-friendly DTC Lookup Function which enables you to retrieve the definitions of any error codes from the large database of AL619, saving you from the hassle of wasting time searching definition of every code via Google.
- 2024 Top Choice for ABS Bleeder Scan Tool - Is the brake pedal always slowly sinking down or becoming loose? This ABS brake bleeding scan tool will cycle the pump and valves to achieve a tight brake pedal. It's the most affordable obd2 scanner with ABS auto bleed. By following the instruction step by step, even a beginner can navigate through easily. Coverage check before purchasing via FOXWELL official site: Support- Diagnostic Coverage List. Tip: It won’t work on vehicles lacking an auto bleed function.
- More Than a Entry Level OBD2 Scanner, Ideal for Home Mechanics - Based on the NT301 FOXWELL Scanner, NT630 Plus takes OBD-II diagnostics to the next level by customizing functions for ABS and SRS system. This SRS and ABS scanner provides in-depth insights on error code diagnosis, wheel speed sensor, airbag circuits, cable connectors monitor, etc... Note: This scanner DOES NOT work on Airbag crash data/programming issues.
- No More Higher End Service than You Need - One NT630 Plus is enough! This obd2 scanner with ABS and SRS takes in-depth diagnosis on Anti-Lock Brake System & SRS/Airbag, and also performs Airbag light reset/ SAS(Steering Angle Sensor) adjustment/ Oil light reset daily reset services. These issues will be restored after the car faults repaired. Note: Some classic vehicles without the electronic control system can not support the reset service.
- Also can Work like NT301 - The NT630 Plus ABS code reader can connect to the OBD-II port directly. It will diagnose all OBD-II modules instantly, displays the live data, locates bad sensors and indicate I/M readiness status before the annual inspection. Guides you to do the maintenance work, reduces the potential driving risk and keep a peak performance on the road.
- Higher-level Services wih Lower Cost - Cost less to own a ABS SRS Bidirectional Scan Tool that is not found on similar code readers & scan tools. This car diagnostic scanner allows you to test all potential car faults in the ABS/Airbag system, with functions returning to normal once you exit the program. Please note, that only ABS/SRS modules are supported.
- [Transform Your Car Care Experience] - With BLCKTEC, instantly become your own professional mechanic. Effortlessly read and clear your car’s trouble codes and check engine light, ensuring your vehicle stays in top condition.
- [Empower Yourself with Comprehensive Diagnostics] - Unlock the full potential of your vehicle with the BLCKTEC 430. Access detailed diagnostics previously exclusive to professional mechanics’ OBD2 scan tools, including ABS, Airbag, SRS, TPMS codes, and beyond, right at your fingertips.
- [Drive with Confidence] - The BLCKTEC 430 is more than just a car code reader; it's your personal vehicle health advisor. Receive tailored repair reports with potential causes and verified solutions for your specific make and model, guiding you to the right fix every time.
- [Seamless Connectivity, Ultimate Convenience] - Experience the freedom of wireless diagnostics with this portable car scanner. Easily connect via Bluetooth to our intuitive sensor, and enjoy all the functionalities of high-end scan tools without the clutter of wires, directly from your smartphone or tablet.
- [DIY Repairs Made Easy] - Navigate car maintenance with ease using our premium app. Access a vast library of easy-to-follow repair videos, guiding you through each step of the repair process, compatible with both iOS & Android devices.
![2024 Newest FOXWELL NT604 OBD2 Scanner ABS SRS, Check Engine Code Reader with Airbag Scanner, Transmission Code Reader Car Diagnostic Tool with Battery Test, English/Spanish Ver,Lifetime Free Update](https://m.media-amazon.com/images/I/511vhwk38oL._SL160_.jpg)
- 🔥【Easy to use and friendly】+【Faster diagnostic speed】 FOXWELL NT604 is the 2024 newest enhanced 4 system code reader, which is capable of reading/clearing fault codes, retrieving vehicle information and displaying 4-in-1 live data stream. You will easily find what's wrong with your car to avoid expensive trip to dealership. At the same time, this car scanner will directly tell you what the corresponding code means, avoiding the hassle of searching for information.
- 🛠【OBD2 Full Function】+【Check Engine/ABS/SRS/Transmission】 This scan tool will allow you to perform full OBDII diagnostic for all cars with OBDII protocols. You can use it to check if your car is ready for annual testing through the I/M Readiness menu. In addition, the device also has value-added functions such as real-time data flow, DTC Lookup, data playback, and printing. Turn off Check Engine/ABS/SRS/Transmission Light. Tips: the fault code can be only erased after the problem is fixed.
- 🚗【Cover 10000+ models &60+ Car Makes】 and 【AUTOVIN】 Compared with Other scanner which only supports 40 car makes, NT604 car diagnostic scanner for all cars contains more than 60 car brands and 10000+ cars for almost all OBDII cars sold worldwide like passenger car, SUVs, minivans, light-duty trucks, etc. produced by Asian, European, American with the supported year differing from 1996 to 2024. It allows you to get your VIN and vehicle info rapidly, no need to take time input one by one.
- 🛒【Battery Voltage Checker】+【Lifetime Free Update, No Subscription fee 】 It monitors the real-time voltage of the vehicle battery and displays it in graphical and textual form, informing you of the health status of the battery. Also monitor the health of your car. NT604 is equipped with the latest software directly, so you don't need to download a bunch of updated software after unboxing to use it. Lifetime no subscription fee for upgrading software.
- 🎁【Great festival Idea:Applicable for Many People】+【High End and Exquisite Protective Packaging】 Best one item for Dad, Husband, Boyfriend, Handy Men. Every car owner will need a 4 systems diagnostic scan tool! This code reader fits for home mechanic, DIY car owners, advanced hobbyiest, car dealer, auto repair shop, automotive engineer, diagnostic tech, automobile tech, individual. Apparently, this is the most economical scan tool for every mechanic.
- 💻Note: (About UPDATE) ANCEL FX2000 car scanner diasgnostic tool can be used directly as it comes with existed software, You don't need to register or update beforethe first use. It's recommended to update your scanner with SD card only when it fails to work on your car, or it's slow to load all menus or if you need newer software version. 📢Software update supports WIN XP, 7, 8, 10 operation systems only, but not for Mac and ios system. 📧Any concerns, pls feel free to 𝙚-𝙢𝙖𝙞𝙡 us via 𝙖𝙢𝙖𝙯𝙤𝙣 @ 𝙖𝙣𝙘𝙚𝙡𝙩𝙚𝙘𝙝. 𝙘𝙤𝙢.
- 🔧【PLUG AND PLAY - EASY TO USE】 : ANCEL FX2000 car scanner only takes 3 steps to connect to the car for diagnosis without cumbersome operations. The latest FX2000 automotive scanner diagnostic tool is equipped with a one-key diagnosis function, which can automatically identify the model and year of your car, and automatically diagnose the car. Even beginners can use this obd2 scanner with abs and srs to read the data and find out what the fault codes mean.
- 🚗【FULL OBD-LEVEL DIAGNOSTICS TOOL】: Quickly determines the cause of engine system faults, reads current, permanent and pending codes. After the repair, clears the codes and turns off the warning light. In addition, the FX2000 OBD2 scanner diagnostic tool also displays important OBD II advanced data such as fuel, live data and other manufacturer-specific parameters in real time to ensure that the engine ECU is operating correctly and safely, saving vehicle owners a lot of time and money in maintenance.
- 🚙【A/T TRANSMISSION FAULT DIAGNOSTIC TOOL】: Some noises come from the A/T transmission? Ancel obd2 scanner will read fault codes, display live transmission system data (fluid temperature, fluid pump, clutch actuation, pressure, etc.), and ensures transmission performance is optimal for vehicle speed and load. This transmission scanner provides detailed TCM data of the vehicle, so you can quickly and accurately find existing or potential problems.
- 🚐【FIND OUT SRS WRONG】: ANCEL FX2000 obd2 scanner with abs and srs is able to read and clear fault codes in the SRS (airbag) and turn off the warning light to make sure the system is working correctly and safely. This odb2 scanner also displays a live graphical data stream of the supplemental restraint system (air bag), which allows you to analyze and verify that the air bag system is working properly.
- SRS Airbag Light Reset Tool - D800 OBD scan tool is design for BMW. The B800 diagnostic scanner ONLY work for BMW's E36/E46/E34/E38/E39/Z3/X5/X3 will allow you to read airbag trouble codes on BMW's
- Compatible - Models available for most BMWs built between 1994 and 2003 like ALL variants in E36/E46/E34/E38/E39/Z3/Z4/X5. But it doesn't work with 2001 BMW 330i.
- High Effective - Reset the dashboard SRS airbag light within seconds. This is a very easy to use tool that comes with instruction manual to help you diagnose problems
- Easy to Use - And clear the code by the enter button; confirms a selection of a menu list or return to the main menu; scrolls through menu items or cancel and operation by the scroll button
- Easy to Understood - With LCD display, it can show the test results and control it by the buttons. Provide 1-year warranty, if you have any issue please contact us with Order ID asap and we will try our best to help you. 🙂
- The VD500 OBD2 scanner is specifically designed to diagnose Volkswagen Group (Fits for VW/Audi/Skoda/ SEAT) 12-volt 16-pin vehicles, but can also be used with other 12-volt (non-Volkswagen) and light trucks (non-electric) vehicles manufactured in 1996 or later that are OBD II -compliant with standard 16-pin OBD II protocols (J1850 VPM, J1850PWM, ISO9141, KWP 2000 and CAN). Please send your vehicle information to our 💌amazon@anceltech.com💌 to check compatibility.
- For Volkswagen (VAG) vehicles diagnostics, the device can not only read and clear codes on engine, ABS, transmission, SAS (not all cars), ESP, TPMS and other systems, but also reset the oil, brake pad and throttle position adaption.
- For other OBD II vehicles (non-Volkswagen), the VD500 can read and clear fault codes, display fault code definitions, turn off the CEL (check engine light) and retrieve VIN information ONLY.
- The VD500 diagnostic offering for Volkswagen vehicles covers the following vehicles: fits for VW (CC, EOS, Golf, GTI, Jetta, Passat, Phaeton, Polo, Rabbit, Sharan, Tiguan, Touran, Touareg); fits for Audi (A3, A4, A6, A7, A8, A5, Q3, Q5, Q7, R8, RS3, TT, RS, RS5, S4, S6); fits for Skoda (Octavia, Rapid, Yeti, Kodiaq, Fabio, Superb); fits for SEAT (Leon, Ateca, Ibiza, Altea, Cushion, Cord, Alhambra) Diagnostics.
- With English and German as display languages, this diagnostic scan tool provides life-time free software updates to fix the latest bugs or add new parameters. Simply download the software from the official website, then follow on-screen instructions to install it.
- 【Great Ideal For Every Car Owner】Prefect choice for your father, husband, brother or boyfriend. EVERY CAR OWNER WILL NEED IT! Also, the lifetime f-ree update is provided for more vehicle coverage, bug fixes. SAVE AT LEAST $1000+ PER YEAR!Get LAUNCH CRP123 Elite car diagnostic scanner and give your lover a surprise!🎁Get the Extra Gifts :Protective Case Storage Bag,please reach us at: cardiag-aftersales @ hotmail.com.
- 【 Read & Clear/Reset Engine/ABS/SRS/Transmission Diagnostic Scan Tool 】LAUNCH CRP123 OBD2 Scanner can test Engine, Transmission, ABS and Airbag four systems, also reads and resets code, displays data stream graphic, stores and playbacks dynamic data stream,helps to quick analysis and diagnosis.
- 【 Error Fault Code Reader】Except the full 10 modes OBD2 diagnostic functions like, retrieving I/M readiness, Freeze Frame Data, Read Dynamic Data stream and V-ehicle Information, O2 Sensor Test, EVAP Test of F-uel Tank System (Mode 8) and Advanced On-board Monitoring (Mode 6), launch crp123 obd2 scanner can not only reveal what error codes your car is producing, but also erase your v-ehicle’s check engine light after problem fixed, the DTC help and explanation also tell you the exact problem.
- 【 Live Data Graphing + Read/Record/Playback Data stream + Print diagnostic data 】Live Data Graphing,more intuitive to know your vehicle’s problem.Large size Color Screen ;Print Function:Print the diagnose result easily; with user manual and register & update tutorial video uploaded in the link by us,you can Look up it anytime by ONE-CLICK.
- 【 Find Your Vehicles Here】Launch CRP123 obd2 scanner Supports mainstream vehicles on the world,fit for ACURA VW AUDI AUST FORD BENZ BMW CHRYSLER FIAT GM HOLDEN HONDA HYUNDAI INFINITI JAGUAR ISUZU KIA LANDROVER LEXUS MAZDA MITSUBISHI NISSAN OPEL PORSCHE SAAB SEAT SKODA SMART MERCEDES SPRINTER SUBARU SUZUKI SCION TOYOTA USA FORD VOLVO PEUGEOT CITROEN RENAULT EUROFORD.Etc.
- [Pro OBD2 Scanner] - BlueDriver is the easiest way to scan and understand your vehicle like a professional mechanic. Read and clear your car’s trouble codes and check engine light.
- [Read & Clear All The Codes] - BlueDriver's enhanced vehicle diagnostics gives you access to information normally available only to mechanics on their OBD2 scan tools. Now you can read and clear ABS, Airbag, SRS, TPMS codes, and many more.
- [Get The Right Fix] - Much more than a car code reader, BlueDriver is a diagnostic tool. Get unlimited specific repair reports containing possible causes, reported fixes, and more for virtually every vehicle make and model.
- [Wireless & Bluetooth Enabled] - Say goodbye to wires. BlueDriver connects with Bluetooth via your phone/tablet to a sensor that plugs into your car's OBDII port. Get all of the capabilities of an expensive code reader & scan tool without any annoying wires.
- [User-Friendly App and Repair Videos] - BlueDriver gives you more ways to scan and fix your vehicle. Our iOS & Android app connects you to a large database of repair videos with step-by-step directions of repairs.
Last update on 2024-06-10 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.