oemdtc

Recalls & Diagnostic Tips
Menu
  • Recalls
    • Aston Martin Recalls
    • BMW Recalls
    • Bugatti Recalls
    • Chrysler Dodge Fiat Jeep Ram Alpha Romeo Recalls
    • Ferrari Recalls
    • Ford Recalls
    • GM Recalls
    • Acura & Honda Recalls
    • Hyundai Recalls
    • Isuzu Recalls
    • Jaguar & Land Rover Recalls
    • Kia Recalls
    • Lamborghini Recalls
    • Maserati Recalls
    • Mazda Recalls
    • Mercedes-Benz Recalls
    • Mitsubishi Recalls
    • Infiniti & Nissan Recalls
    • Porsche Recalls
    • Subaru Recalls
    • Suzuki Recalls
    • Tesla Recalls
    • Toyota Lexus & Scion Recalls
    • Volvo Recalls
    • VW Audi Recalls
  • Diagnostic Tips
    • Ford Diagnostic Tips
    • GM Diagnostic Tips
    • Mazda Diagnostic Tips
    • Subaru Diagnostic Tips
  • Repair Tips
    • Ford Repair Tips
    • GM Repair Tips
    • Mazda Repair Tips
    • Subaru Repair Tips
  • Links
  • E-Books
  • Store
  • oemdtc
    • Aston Martin
    • BMW
    • Bugatti
    • Chrysler Dodge Fiat Jeep Ram Alpha Romeo
    • Ferrari
    • Ford
    • GM
    • Acura & Honda
    • Hyundai
    • Isuzu
    • Jaguar & Land Rover
    • Kia
    • Lamborghini
    • Maserati
    • Mazda
    • Mercedes-Benz
    • Mitsubishi
    • Infiniti & Nissan
    • Porsche
    • Subaru
    • Suzuki
    • Tesla
    • Toyota Lexus & Scion
    • Volvo
    • VW-Audi

Amazon Sells Car & Truck Parts Search by Part Number

Buy Car & Truck Parts on Amazon
Home
Recalls
VVK0009 - Improper Lamps and Missing Reflectors/FMVSS 108 - 2016-2020 Vac-Tron CS1273GT, CS870GT, CS1270GT, CS873GT, CV1273GT, CV1273SGT & LP1273XDT Vacuum Excavator Trailers
Recalls

VVK0009 - Improper Lamps and Missing Reflectors/FMVSS 108 - 2016-2020 Vac-Tron CS1273GT, CS870GT, CS1270GT, CS873GT, CV1273GT, CV1273SGT & LP1273XDT Vacuum Excavator Trailers

oemdtc May 29, 2020 No Comments

May 20, 2020 NHTSA CAMPAIGN NUMBER: 20V290000

Improper Lamps and Missing Reflectors/FMVSS 108

Due to the improper position of the lamps, insufficient reflective tape, and lack of reflectors, the vacuum excavator trailer may not be sufficiently visible during low visibility conditions, increasing the risk of a crash.

 

NHTSA Campaign Number: 20V290

Manufacturer Vac-Tron Equipment, LLC

Components EXTERIOR LIGHTING

Potential Number of Units Affected 105

 

Summary

Vac-Tron Equipment, LLC. (Vac-Tron), a subsidiary of Vermeer Manufacturing Company (Vermeer), is recalling certain 2016-2020 CS1273GT, CS870GT, CS1270GT, CS873GT, CV1273GT, CV1273SGT and LP1273XDT Vacuum Excavator trailers. The front clearance lamps may be positioned improperly and an insufficient amount of conspicuity tape may have been applied on the sides and rear. The trailers may also may also lack side or rear reflex reflectors. As such, these vehicles fail to comply with Federal Motor Vehicle Safety Standard Number 108, "Lamps, Reflective Devices, and Associated Equipment."

 

Remedy

Vac-Tron will notify owners, and Vermeer dealers will install remedy kits provided by Vac-Tron, free of charge. This recall began July 14, 2020. Owners may contact Vac-Tron customer service at 1-888-822-8766. Vac-Tron's number for this recall is VVK0009.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.


Vac-Tron Equipment, LLC

Trenchless
Okahumpka, FL  34762 USA

 

FIELD CAMPAIGN

SERVICE BULLETIN # SVV2020-011

DATE: 30 June 2020

 

CAMPAIGN TYPE:Mandatory-Product Safety
CAMPAIGN CATEGORY:Kit and Bulletin

 

MACHINE /

ATTACHMENT

MODEL (S) :

Serial Numbers
IncludedExcludedKit Version
CSGTSee attached listing on page 4 of this Bulletin for specific VIN and Serial/Unit numbers.N/AVVK01
CV1273SGT
CVGT
CVSGT
LP1273XDT

 

Subject:

PRODUCT SAFETY RECALL

FIRST NOTICE

Light Relocation, Reflector, Conspicuity Tape and Rear Extension Installation Kit (VVK00-0009)

 

Background:

INADEQUATE LIGHTING, REFLECTORS AND CONSPICUTITY TAPE

The lighting, side and rear reflectors and conspicuity tape do not meet US or Canada Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) governmental regulation 108 for the Unites States, Canada and Mexico. The trailers may not have an extended lower rear chassis, reducing rear impact protection and does not meet US or Canada Federal Motor Vehicle Standard (FMVSS/CMVSS) government regulation 223 for the United States, Canada and Mexico.

 

DEATH OR SERIOUS INJURY POSSIBLE

When towing or parking the vacuum excavator on public roadways, a crash may occur resulting in death or serious injury resulting from a driver(s) of other vehicle(s) not seeing the vacuum excavator at night or during limited sunlight and strike the vacuum excavator. To reduce the potential of this occurring, vehicle lights will be relocated, additional reflectors and conspicuity tape are being added.

In the event of a rear impact crash, the other vehicle may travel under the rear of the vacuum excavator, increasing the risk of serious injury or death to someone in the other vehicle or to the towing vehicle occupants.

Property or equipment damage may also occur.

 

Solution:

IMMEDIATE MACHINE MODIFICATIONS REQUIRED

VVK00-0009 has been created to provide the necessary parts and instructions to relocate the vehicle lights, add reflex reflectors, add conspicuity tape to the sides and rear, and add a rear extension. This kit must be installed as soon as possible.

Please be reminded that it is a violation of Federal law for you to sell or lease the machines covered by this notification until this recall has been performed on these machines. Substantial civil penalties apply to violations of this law.

 

DEALER PARTICIPATION
REVIEW REPORT, ORDER KITS, CONTACT CUSTOMERS

  1. Reports will be emailed during the week of June 30, 2020, to dealerships shown in our records which have units in their territory affected by this Alert. Please review the report for accuracy, including owner and/or address changes.

If the information contained in the report is NOT correct, please notify the Product Safety Department on or before July 13, 2020 at:

Telephone: 641-621-7060
Fax:  641-621-8562
Email: [email protected]

 

  1. Dealerships Order Kits by calling Vac-Tron at 888-822-8766.

Each dealership should determine the quantity of Kits to order initially depending upon the number of units that may be available for immediate upgrade. Do not order more Kits than needed for immediate installation.

 

  1. Contact your affected customer(s) to schedule a mutually acceptable time to upgrade their machine. Note: Letters will be sent to the customer(s) on or about July 14, 2020. Also refer to Owner Notification section below.

If you have any questions concerning the installation of VVK00-0008, please contact the Vac-Tron Service Department. Vermeer Corporation is assisting Vac-Tron with the administration of this campaign.

 

REIMBURSEMENT

Upon completion of each Kit installation, a campaign Warranty Claim must be submitted to the Vermeer Corporate Warranty Department for reimbursement of the parts cost and labor of the Kit.

 

This kit will reimburse 6 labor hours.

 

Note: Future notices to dealers and owners are dependent upon the receipt of Warranty Claim.

 

OWNER NOTIFICATION

Sample Letter: Included at the end of this Bulletin is a sample letter which will be sent by Vermeer Corporation directly to the Owners on or about July 14, 2020, via USPS certified/registered mail. Owner registrations indicate no translations are required for this campaign. The owner letter will be available in English only.

This owner notification/letter instructs the owner to contact their local dealership to arrange for a time to have the Kit installed. After receiving IK00-xxxx from the Parts Center, you must contact your affected customer(s) immediately and schedule a mutually acceptable time to upgrade their machine.

We regret any inconvenience these corrective measures may cause you. This required work is for safety of the safety of the towing vehicle driver and occupants as well as other traveling on public roadways or in the immediate are while being towed. We hope you agree the safety benefits surpass the inconvenience.

 

VAC-TRON EQUIPMENT, INC.

Attachment:
VVK00-0009 Kit Instructions

 


AFFECTED MACHINES - VVK01-0009
MODELVINSERIAL/UNITMODELVINSERIAL/UNIT
CSGT5HZB192W5LK002039191830CVGT5HZC192X5LK002099200111
CSGT5HZB192W0LK002045200131CVGT5HZC192X4LK002126200291
CSGT5HZB192W7LK002060200269CVSGT5HZD192Y1LK002064191708
CV1273SGT5HZBF2420JLJJ5102181524CVSGT5HZD192Y2LK002073191769
CVGT5HZC192X0KK002008191289CVSGT5HZD192Y9LK002085191831
CVGT5HZC192X9KK002055191643CVSGT5HZD192Y3LK002101200029
CVGT5HZC192X0KK002056191644CVSGT5HZD192Y6LK002125200155
CVGT5HZC192X2KK002057191645CVSGT5HZD192Y6LK002139200230
CVGT5HZC192XXLK002096200070CVSGT5HZD192Y7LK002148200297
CVGT5HZC192X1LK002097200072LP1273XDT5HZBF2121KLCK8100191178
CVGT5HZC192X3LK002098200110

 


NHTSA SAFETY RECALL NUMBER 20V-290 and 20V-293

IMPORTANT SAFETY RECALL

First Notice

Light Relocation, Reflector, Conspicuity Tape and Rear Extension Installation Kit   (VVK00-009)

 

Sample Owner Letter

 

Model: «Model»

This notice applies to your vehicle,

Serial No: «VIN»

Unit No: «PART_SRL»

 

VIA USPS CERTIFIED/REGISTERED MAIL

July 14, 2020

Dear «MODEL» Owner:

This notice is sent to you in accordance with the requirements of the U.S. National Traffic and Motor Vehicle Safety Act.

Vermeer has decided that a defect, that relates to motor vehicle safety, exists in certain model year 2016-2020 Vermeer «MODEL».

 

INADEQUATE LIGHTING, REFLECTORS AND CONSPICUTITY TAPE

The lighting, side and rear reflectors and conspicuity tape do not meet US or Canada Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) governmental regulation 108 for the Unites States, Canada and Mexico.

The trailers may not have an extended lower rear chassis, reducing rear impact protection and does not meet US or Canada Federal Motor Vehicle Standard (FMVSS/CMVSS) government regulation 223 for the United States, Canada and Mexico.

 

DEATH OR SERIOUS INJURY POSSIBLE

When towing or parking the vacuum excavator on public roadways, a crash may occur resulting in death or serious injury resulting from a driver(s) of other vehicle(s) not seeing the vacuum excavator at night or during limited sunlight and strike the vacuum excavator. To reduce the potential of this occurring, vehicle lights will be relocated, additional reflectors and conspicuity tape are being added.

In the event of a rear impact crash, the other vehicle may travel under the rear of the vacuum excavator, increasing the risk of serious injury or death to someone in the other vehicle or to the towing vehicle occupants.

Property or equipment damage may also occur.

 

IMMEDIATE MACHINE MODIFICATIONS REQUIRED

VVK00-009 has been created to provide the necessary parts and instructions to relocate the vehicle lights, add reflex reflectors, add conspicuity tape to the sides and rear, and add a rear extension. This kit must be installed as soon as possible.

Please contact your authorized, independent Vermeer dealer immediately to arrange a mutually acceptable time and location to install VVK00-009 at no cost to you for labor or materials. The installation of this kit is estimated at 6 hours of labor.  If the Vermeer dealer travels to the unit to install the kit, costs may be incurred by the owner. You must have your machine upgraded for these safety features.

 

Contact your local Vermeer Dealer:  «Service_Dealer_Name»
«Serv_Dealer_Add1» «Serv_Dealer_Add2»
«Serv_Dealer_City» «Serv_Dealer_St» «Serv_Dealer_Zip»
«SERV_DEALER_COUNTRY» Telephone: «Serv_Dealer_Phone»

 

According to our records, you currently own a Vermeer «MODEL» vacuum excavator trailer. The Model and Serial Number of the «MODEL» is shown at the top right of this letter.  If you no longer own this unit, please notify the Product Safety Department at:

Toll Free: 800-829-0051, extension 7060
Telephone: 641-621-7060
E-mail: [email protected]

If possible, please provide the name and address of the new owner. Vermeer Corporation is  Vac-Tron with the administration of this campaign.

 

We regret any inconvenience these corrective measures may cause you. This required work is for safety of the safety of the towing vehicle driver and occupants as well as other traveling on public roadways or in the immediate are while being towed. We hope you agree the safety benefits surpass the inconvenience.

 

Very truly yours,

VAC-TRON EQUIPMENT, LLC

 

Federal regulations require that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten (10) days.

 

If the authorized dealer has failed or is unable to remedy the defect without charge and within a reasonable time, contact Vermeer Product Safety by email at [email protected] or by calling 800-829-0051 or 641-621-7060. You may also submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, D.C. 20590 or call the Vehicle Safety Hotline at 888-327-4236 (TTY: 1-800-424-9153); or go to http://www.safercar.gov

 


Vac-Tron Equipment, LLC

Trenchless
Okahumpka, FL 34762 USA

 

FIELD CAMPAIGN KIT VVK0000009

DATE: 30 June 2020

For Dealer Reference: Service Bulletin # SVV2020-011

Light Relocation, Reflector and Conspicuity Tape Installation Kit

CAMPAIGN TYPE:Mandatory-Product Safety
CAMPAIGN CATEGORY:Kit and Bulletin

 

MACHINE /

ATTACHMENT

MODEL (S) :

Serial Numbers
IncludedExcludedKit Version
CSGTSee attached listing on page 17 of this Kit Instructions for

specific VIN and Serial/Unit numbers.

N/AVVK01
CV1273SGT
CVGT
CVSGT
LP1273XDT

 

PURPOSE: INADEQUATE LIGHTING, REFLECTORS AND CONSPICUTITY TAPE

The lighting, side and rear reflectors and conspicuity tape do not meet US or Canada Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) governmental regulation 108 for the United States, Canada and Mexico. When towing or parking the vacuum excavator on public roadways, a crash may occur resulting in death or serious injury resulting from a driver(s) of other vehicle(s) not seeing the vacuum excavator at night or during limited sunlight and strike the vacuum excavator. To reduce the potential of this occurring, vehicle lights will be relocated, additional reflectors and conspicuity tape are being added.  Property or equipment damage may also occur.

 

Shutdown Procedure

STOPPING THE MACHINE

 

For your safety and the safety of others, follow shutdown procedure before working on the machine for any reason, including servicing, maintaining, cleaning, inspecting, unclogging or transporting machine, or as otherwise directed in Operator’s manual.

 

Step 1: Make sure end of vacuum hose is clear of all spoils, debris, and other materials.

 

Step 2: Push Throttle Control left several times to slow engine.  Idle engine five minutes to allow vacuum pump (with Reverse Flow Lever – Neutral) to cool down.  This helps to prevent the buildup of condensation.

 

Step 3: Turn Key Switch OFF to shut down engine.

 

Step 4: Drain Filter Housing.

 

PROCEDURE 1:

 

  1. Align the bracket with the edge of the curb side I-beam as shown below. Ref. 1, Fig 1.

 

  1. Mark the light bracket hole locations onto the I-beam and drill (2) Ø9/32” (7.15 mm) holes through the I-beam.

 

  1. Attach the marker light bracket with the supplied hardware. Ref. 1, 2, 3, and 4, Fig. 1.

 

 

  1. Connect one end of the 100” (2.54 m) length of dual core wire to the front side marker lamp using the butt connectors. 5 and 6, Fig. 1.

 

  1. Place loom over wires for protection. Ref. 8, Fig. 1.
  2. Run the wire through the cross member and inside of the I-Beam to connect with the front clearance marker lamp. Reference step 3, Procedure 2 for connecting the front side marker lamp and front clearance marker lamp.

 

  1. Use supplied zip ties to fasten wire harness to trailer frame.
  2. Complete all steps for the street side of the trailer.

 

PROCEDURE 2:

 

  1. Remove the curb side marker light from the platform gusset and disconnect the wires. Retain the marker light for future installation.

 

  1. Place the front clearance marker bracket on the gusset approximately 1-1/2” (3.81 cm) from the bottom as shown in Figure C. If the location of the antifreeze tank stand interferes with positioning the bracket properly, position the marker bracket just below the antifreeze tank stand as shown if Figure D.  Mark the bolt locations on the gusset and drill (2) Ø9/32” (Ø7.15 mm) holes. (Curb side shown). Ref. 1

 

  1. Use the 1 ft (30.48 cm) length of dual core conductor wire to reconnect the front clearance marker lamp and tie in with the 100” (2.54 m) length wire from the front side marker lamp. Use the 12-10 (yellow) and 16-14 (blue) heat seal butt connectors to connect all wires according to diagram below.

 

  1. Insert the front clearance marker lamp into the front clearance marker bracket as shown. Ref A, Fig. 2 for VVK01. Ref 2, Fig 2 for VVK02.  Refer to the illustration below for proper lamp orientation.
  2. Attach the front clearance marker bracket with the hardware Ref. 3, 4, and 5 Fig. 2.
  3. Loom all exposed wires. Ref. 8 Fig. 2.
  4. Repeat all steps to connect the front clearance marker lamp on the street side of the trailer.

 

PROCEDURE 3:

 

  1. Clean area where the conspicuity tape will be installed with light soap and water. Areas with damaged paint or heavy corrosion should be prepped, painted, and thoroughly dry before applying conspicuity tape.
  2. Refer to the illustration and install the conspicuity tape in the locations shown. Ref. 1 and 2, Fig. 3.
  3. Repeat for the opposite side of the trailer.

 

PROCEDURE 4:

 

  1. Remove the existing rear corner/side clearance marker lamp from the gusset and disconnect the wires. Retain the light for future installation.

 

  1. Place the rear corner/side clearance marker bracket on the support approximately 1-1/2” (3.81 cm) from the bottom as indicated in the illustration below. Mark the bolt locations on the support and drill (2) Ø9/32” (Ø7.15 mm) holes.
  2. Use the 1 ft (30.48 cm) length of dual core conductor wire to reconnect the rear corner/side clearance marker lamp using 16-14 butt connectors. Ref A, 7 and 8, Fig 4 for VVK01.

 

  1. Attach the rear corner/side clearance marker bracket to the fender support with the hardware as shown Ref. 3, 4, and 5 Fig. 4.
  2. Loom all exposed wires. Ref. 9 Fig. 4.
  3. Insert the rear corner/side clearance marker lamp into the bracket as shown Ref 1 and A, Fig. 4.
  4. Clean area where the rear side marker reflectors will be installed with light soap and water. Areas with damaged paint or heavy corrosion should be prepped, painted, and thoroughly dry before applying the reflectors as shown.

 

  1. Install the rear side marker reflector below the side marker bracket as shown.
  2. Repeat all steps for the opposite side of the trailer.

 

PROCEDURE 5:

 

  1. Clean area where the conspicuity tape will be installed with light soap and water. Areas with damaged paint or heavy corrosion should be prepped, painted, and thoroughly dry before applying the conspicuity tape.
  2. Refer to the illustration and install each of the white conspicuity tape on the debris tank door and water tanks as shown Ref 1, Fig. 5.

 

PROCEDURE 6:

 

  1. Ensure the debris tank is empty. Using suitable blocking, block debris tank to prevent shifting.  Debris tank weighs approximately 1,000 lb (455 kg).
  2. Remove the cotter pin on both sides.
  3. Push the headed pins out to be flush with the inner side of the tank hinges. Be careful not to push the pin through the hinge.

 

  1. Push the headed pins out to be flush with the inner side of the tank hinges. Be careful not to push the pin through the hinge.
  2. Use a suitable lifting device when installing the bumper. Bumper weight is approximately 120 lb (55 kg).
  3. Inspect the tank hinges connected to the bumper. Hinges with the single hole configuration shown must be replaced.  If the hinges have a 2-hole configuration, skip to step 9.

 

  1. Use a cutting torch to remove the (4) tank hinges from the bumper. Grind away residual slag.

 

  1. Remove all damaged paint down to bare metal. Repaint all affected areas.
  2. Install the bumper and align the bolt holes with the tank hinges.

 

  1. Push the headed pins back into position and replace the cotter pins on both sides.
  2. Install the hardware Ref. 3, 4, and 5 Figure 6. Tighten the bolts to 644 ft-lb (873 Nm).

 


AFFECTED MACHINES - VVK01-0009
MODELVINSERIAL/UNITMODELVINSERIAL/UNIT
CSGT5HZB192W5LK002039191830CVGT5HZC192X5LK002099200111
CSGT5HZB192W0LK002045200131CVGT5HZC192X4LK002126200291
CSGT5HZB192W7LK002060200269CVSGT5HZD192Y1LK002064191708
CV1273SGT5HZBF2420JLJJ5102181524CVSGT5HZD192Y2LK002073191769
CVGT5HZC192X0KK002008191289CVSGT5HZD192Y9LK002085191831
CVGT5HZC192X9KK002055191643CVSGT5HZD192Y3LK002101200029
CVGT5HZC192X0KK002056191644CVSGT5HZD192Y6LK002125200155
CVGT5HZC192X2KK002057191645CVSGT5HZD192Y6LK002139200230
CVGT5HZC192XXLK002096200070CVSGT5HZD192Y7LK002148200297
CVGT5HZC192X1LK002097200072LP1273XDT5HZBF2121KLCK8100191178
CVGT5HZC192X3LK002098200110

 


 

FIGURE 1 Parts List
REF. NO.PART NO.DESCRIPTIONVVK01 QTY.
1B134-5749FRONT SIDE MARKER LAMP BRACKET WITH REFLECTOR2
2P-14731/4-20 X 1 HEX HEAD BOLT4
3P-14721/4 ID FLAT WASHER4
4P-27821/4-20 NYLON LOCKNUT4
5P-1054100” (2.54 m) LENGTH DUAL CORE CONDUCTOR WIRE2
6P-236916-14 HEAT SEAL BUTT CONNECTOR BLUE4
7P-1301ZIP TIE15
8P-27621/2" SPLIT WIRE LOOM, 100” (2.54 m) LENGTH2

 

FIGURE 2 Parts List
REF. NO.PART NO.DESCRIPTIONVVK01 QTY.
1B134-5748FRONT CLEARANCE MARKER LAMP BRACKET2
AP-4190FRONT CLEARANCE MARKER LAMP (EXISTING ON TRAILER)2
3P-14731/4-20 X 1 HEX HEAD BOLT4
4P-14721/4 ID FLAT WASHER4
5P-27821/4-20 NYLON LOCKNUT4
6P-10541’ (30.48 cm) LENGTH DUAL CORE CONDUCTOR WIRE2
7P-161112-10 HEAT SEAL BUTT CONNECTOR4
8P-27621/2" SPLIT WIRE LOOM, 1’ (30.48 cm) LENGTH2
9P-236916-14 HEAT SEAL BUTT CONNECTOR BLUE4

 

FIGURE 3 Parts List
REF. NO.PART NO.DESCRIPTIONVVK01 QTY.
1P-14262” (2.5 cm) WIDE, 101 ”(256.5 cm) LONG CONSPICUITY TAPE2
2P-14262” (2.54 cm) WIDE, 25” (63.5 cm) LONG CONSPICUITY TAPE2

 

FIGURE 4 Parts List
REF. NO.PART NO.DESCRIPTIONVVK01 QTY.
1B134-5748REAR CORNER/SIDE CLEARANCE MARKER LAMP BRACKET2
AP-4189REAR CORNER/SIDE CLEARANCE MARKER LAMP (EXISTING ON TRAILER)2
2P-4189REAR CORNER/SIDE CLEARANCE MARKER LAMP0
3P-14731/4-20 X 1 HEX HEAD BOLT4
4P-14721/4 ID FLAT WASHER4
5P-27821/4-20 NYLON LOCKNUT4
6P-5730REAR SIDE MARKER REFLECTOR4
7P-10541’ (30.48 cm) LENGTH DUAL CORE CONDUCTOR WIRE2
8P-236916-14 HEAT SEAL BUTT CONNECTOR BLUE8
9P-27621/2" SPLIT WIRE LOOM, 1’ (30.48 cm) LENGTH2

 

FIGURE 5 Parts List
REF. NO.PART NO.DESCRIPTIONVVK01 QTY.
1P-5783WHITE CONSPICUITY TAPE4

 

FIGURE 8 Parts List
REF. NO.PART NO.DESCRIPTIONVVK01 QTY.
1135500258REAR EXTENSION1
ASA-4471HEADED PIN (EXISTING ON TRAILER)2
31355002181-8 X 6-1/2 HEX BOLT2
4P-38271 ID FLAT WASHER4
5P-26261-8 PREVAILING TORQUE NUT2
6135500216TANK HINGE BRACKET4

 


35 Affected Products

Vehicles

MAKEMODELYEAR
VAC-TRONCS 1270 GT2016-2020
VAC-TRONCS 1273 GT2016-2020
VAC-TRONCS 870 GT2016-2020
VAC-TRONCS 873 GT2016-2020
VAC-TRONCV 1273 GT2016-2020
VAC-TRONCV 1273 SGT2016-2020
VAC-TRONLP 1273 XDT2016-2020

5 Associated Documents

Recall Acknowledgement

RCAK-20V290-2797.pdf 245.533KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [239.78 KB]


Non-Compliance Notice 573 Report

RCLRPT-20V290-1336.PDF 217.659KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [212.56 KB]


Miscellaneous Document-BEFORE AND AFTER

RMISC-20V290-2195.pdf 609.92KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [595.62 KB]


Remedy Instructions and TSB

RCRIT-20V290-1584.pdf 2380.489KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.27 MB]


Safety Bulletin

RCSB-20V290-2547.pdf 1199.269KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.14 MB]


Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V290&docType=RCL

For the most up to date documents from NHTSA for this Recall, click the lick above


 

Bestseller No. 1
CARTMAN Warning Triangle DOT Approved 3PK, Identical to: United States FMVSS 571.125, Reflective Warning Road Safety Triangle Kit
CARTMAN Warning Triangle DOT Approved 3PK, Identical to: United States FMVSS 571.125, Reflective Warning Road Safety Triangle Kit
  • DOT approved! Effective REFLECTIVE!
  • 17-inch folding triangle, 3pcs per pake
  • Meets DOT standard FMVSS 571.125 specifications
  • Non-skid base withstands up to 40 meters per hour winds
  • Brilliant red reflectors on both sides of triangle for nighttime safety
$26.99
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 2
MAXXHAUL 50016 Oval Reflectors 10 Red-10 Amber Self Adhesive Or Drill Mount-DOT, 20 Pack
MAXXHAUL 50016 Oval Reflectors 10 Red-10 Amber Self Adhesive Or Drill Mount-DOT, 20 Pack
  • Provides instant visibility to your vehicles, trailers, trucks, RV's, campers, hitch mount accessories such as bike racks, cargo carriers and more up to 100 ft. away
  • Includes mounting holes for drill-on or use self adhesive backing for quick and easy installation on any flat surface
  • Overall size of each reflector 4-3/8" x 2" x 1/4" thick oval
  • Kit comes with 10 amber and 10 red reflectors
  • DOT compliant
$23.12
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 3
United Pacific (2) Red 3' Round Truck Semi Trailer Mail Box Reflex Reflectors/Aluminum Base
United Pacific (2) Red 3" Round Truck Semi Trailer Mail Box Reflex Reflectors/Aluminum Base
  • Misc. Auto Parts
  • Misc. Auto Parts
  • Misc. Auto Parts
  • Misc. Auto Parts
  • Misc. Auto Parts
$7.99
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 4
Rustark 20 Pcs Reflective Tape Waterproof Self-adhesive Reflector Conspicuity Safety Caution Warning Sticker for Truck Trailer Pickup Mailbox(Red and White)
Rustark 20 Pcs Reflective Tape Waterproof Self-adhesive Reflector Conspicuity Safety Caution Warning Sticker for Truck Trailer Pickup Mailbox(Red and White)
  • ⚡【What you Get】 The set contains 10 piece white and 10 piece red car reflector sticker:147 x 50 x 6mm/ 5.8 x 2 x 0.24 inches(L*W*T).Playing a warning and reminder role and guarantying your safe in driveway.
  • ⚡【Highly Visible】 The hexagonal honeycomb pattern ensures the reflective safety tape reflecting light better whatever in the daytime or nighttime. It is mountable at any position to reflect light back at its most visible angle.
  • ⚡【Applied in any weather】The reflective tape with good visibility and viscosity, waterproof and wash-resistant so that you could applied them in any environment or conditions: rainy, foggy or dark night and daytime.
  • ⚡【Long Service time】Made of high-quality plastic, high temperature and durable. The sticky adhesive is waterproof and weather resistant ensuring FIVE to SEVEN years long-life. Moreover, easy to install: Peel Backing off and Stick on with Pressing.
  • ⚡【Universal Application】 Work great for trailers boats,minibus,tank trucks,pickup truck, campers,motorcycle,cars,bicycles,trucks,cars,campers,motorcycle and mailboxes.raincoat,clothing, walls, helmet, and other agricultural equipment.
$9.96
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 5
2' X 30ft Reflective Safety Tape DOT C2 Red White Waterproof Outdoor, Conspicuity Tape, Reflector Tape for Trailers, RV, Camper, Boat High Intensity Grade
2" X 30ft Reflective Safety Tape DOT C2 Red White Waterproof Outdoor, Conspicuity Tape, Reflector Tape for Trailers, RV, Camper, Boat High Intensity Grade
  • DOT-C2 APPROVED: Each red & white reflective strip is marked with DOT-C2, you won’t have to worry about safety and regulations, because it was approved by the dot and exceeds standards
  • EXTRA REFLECTION AND VISIBILITY: DOT-C2 red & white reflective tape is equipped with a highly visible diamond pattern. It provides that extra visibility when needed on dark roads and catches the light from any angle
  • STAYS STRONG, STAYS LONG: Easy, user-friendly installation; simply stick to clean, smooth surfaces.
  • VISIBILITY FOR ALL VARIETIES: Perfect for trucks, snow plows, back hoes, forklifts, in rigging, hauling, and other lifting applications. You can even use it for your mailbox, your boat, or your horse trailer. Shine bright against the night with retro reflective elements
  • Versatile: Take advantage of DOT C2 certified / approved reflective tape at a better value. Slap it on anything that can use the extra visibility: trailers, flatbeds, tankers, tractors, freights, rigs, boats, rail cars, buses, cranes, and containers
$14.95
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 6
Waterproof Reflective Safety Tape Roll 2'X150' Feet Long Yellow Black DOT C2 Auto Truck Safety Reflector Strips Self-adhesive Conspicuous Safety Hazard Caution Warning Sticker for Vehicle Car TrailerW
Waterproof Reflective Safety Tape Roll 2"X150' Feet Long Yellow Black DOT C2 Auto Truck Safety Reflector Strips Self-adhesive Conspicuous Safety Hazard Caution Warning Sticker for Vehicle Car TrailerW
  • 【Generous Size】Federal mandate requires all new trailers to be equipped with 2" wide reflective tape, and you’re in luck, because our conspicuity reflective tape roll is 2" wide x 142 feet long,has a alternating 6 inch red and 6 inch white reflective color blocks, along with an additional layer of rhombus patterned prisms for added visibility.You can run this tape along both sides and rear of the trailer with easy application and durable hold
  • 【Standard DOT-C2 Reflective Adhesive Tape】DOT-C2 Approved: You won’t have to worry about safety and regulations,”DOT-C2” is printed on every white and red reflective rectangle all along its length so you know that it is approved and exceeds specification.Can be sticked on any surface, metal, wood, plastic and nylon.Most people use it for vehicles, road markings, transport facilities, home safety, ships, fairways, and mechanical equipment
  • 【High Strength Polymer Adhesive】This reflective tape is UV stable with a strong industrial strength polymer adhesive hold.It is resistant to solvents such as kerosene, gasoline, diesel, toluene, and turpentine.Single layer design allows for flexible application while still adhering to any surface,can withstand extreme temperatures and will not damage in the elements
  • 【Ultra Reflective】Our DOT C2 reflective tape surface is equipped with a highly visible rhombus patterned prisms with smooth and glossy surface that reflects light in any situation.With alternating birght red and white,the high reflective tape gives you extra security while driving at night,when you stick it to your trailer, truck or car, it can be seen more conspicuous to other drivers to raise awareness on the roads and reduce unnecessary accidents
  • 【Water-proof】Our reflective safety sticker is water-proof,weather-proof and pesist,strong self-adhesive backing that is weather and water resistant for a long lasting hold in even the harshest elements.The longer you use our tape the more sticky it gets to vehicle's surface.So feel free to wash your vehicle and don't worry about fading or peeling off,our high quality reflector tape will last for years!
$32.73
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 7
Fasmov Triple Warning Triangle Emergency Warning Triangle Reflector Safety Triangle Kit, 3-Pack
Fasmov Triple Warning Triangle Emergency Warning Triangle Reflector Safety Triangle Kit, 3-Pack
  • Collapsible design for easy car storage and quick set up, no tools required
  • Size:16.5*16.5*16.5 inches, Weighted base assures stability while the universally recognized shape, size and color alert motorists
  • Can fit flat ground, excellent stability
  • Alerts motorists to roadside trouble day or night keeping you and your passengers safe
  • Ideal for use during roadside breakdowns or other emergencies
$16.99
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 8
3M Reflective Tape Aluminum Reflectors 24'x3' for Truck Trailer Mudflap Hanger - 1 Pair
3M Reflective Tape Aluminum Reflectors 24"x3" for Truck Trailer Mudflap Hanger - 1 Pair
  • 3M Reflective tape(Red White), 24"x3" No peeling off
  • Easy installation(Do not stick)
  • Durable metal material
  • Waterproof
  • Specifically designed for the semi truck and trailer mud flaps/mud flap hangers
$29.99
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 9
2' X 50 ft Reflective Safety Tape DOT Approved Red White For Trailers 2 Inch - Reflector Tape High Intensity Grade Trailer Trucks Auto Reflectors -Typhon East
2" X 50 ft Reflective Safety Tape DOT Approved Red White For Trailers 2 Inch - Reflector Tape High Intensity Grade Trailer Trucks Auto Reflectors -Typhon East
  • VALUE SIZE - 50 feet in length X 2 inches width.
  • INDUSTRIAL STRENGTH - Adhesive: The reflective tape can be adhered on any surface, metal, wood, and plastic.
  • HIGH QUALITY- Ultra Reflective: UV Resistant, Honeycomb Pattern design (PET Material) dot tape, high visibility red and white color.
  • MULTI PURPOSES- Great for trailers, commercial vehicles, automotive, bikes, motorcycles, marine use, agricultural equipment, campers, RVs, and helmets.
  • CUSTOMER GUARANTEE -At Typhon east, we believe in old-fashioned service and quality. If you are dissatisfied with your purchase in any way, please reach out to us and we will gladly issue a full refund
$16.99
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 10
Reflective DOT-C2 Waterproof Adhesive Conspicuity Red-White Reflector Tape for Automotive Vehicles, Bikes,Trailers, Trucks, Cars, Boats, Signs, Helmets, Outdoor 2 Inch x 20 Feet
Reflective DOT-C2 Waterproof Adhesive Conspicuity Red-White Reflector Tape for Automotive Vehicles, Bikes,Trailers, Trucks, Cars, Boats, Signs, Helmets, Outdoor 2 Inch x 20 Feet
  • HIGH VISIBILITY: This red and white reflective tape will maximize vehicle's visibility at night. Able to reflect ultra-bright light in all directions.The high visibility tape is made of a new material combined with coating, compounding and embossing technology, also using the combination of micro glass beads technology and microprisms technology to create a highly vinyl reflective surface.
  • INDUSTRIAL STRENGTH ADHESIVE: Extra strength of stickiness Industrial grade adhesive reflective tape, extremely sticky and waterproof for long lasting and dependable application, please make sure the surface where you want to apply tape is dry and clean.
  • GREAT DURABILITY AND FADE RESISTANT: Our weatherproof DOT high luminance reflective tape will resistance to extreme weather like snow, frog, rain. Longest durability and life cycle available, colors will not fade, dull or tarnish even in extreme sun or cold.
  • APPLICATION VARIOUS: The durable conspicuous reflective safety tape can be used indoor or outdoor, perfect for sign, marking, cargo, garage door, truck, different types of trailer, truck, bicycle, car, agricultural equipment, automotive vehicle, RV, boat, mailbox, campers.
  • YOUR SATISFACTION IS SUPER IMPORTANT TO US. Any questions, pls feel free to contact us by email.
$9.59
Buy on Amazon Price incl. tax, excl. shipping

Last update on 2021-02-19 / Affiliate links / Images from Amazon Product Advertising API

Last update on 2021-02-19 / Affiliate links / Images from Amazon Product Advertising API

Email
Tweet
Share
Pinterest
Linkedin
Stumble
Reddit
Whatsapp
Telegram
Tumblr
Pocket
Buffer
Vkontakte
Prev Article
Next Article

Related Articles

Dennis Eagle Elite
NHTSA Campaign Number: 18V653 Manufacturer Dennis Eagle Inc. Components ELECTRICAL SYSTEM Potential Number …
Recalls oemdtc October 17, 2018 No Comments

Ignition Barrel may Rotate causing Stall - 2017-2018 Dennis Eagle Elite Garbage Trucks

Bridgestone
NHTSA Campaign Number: 18T011 Manufacturer Bridgestone Americas Tire Operations,LLC Components TIRES Potential Number …
Recalls oemdtc September 30, 2018 No Comments

Steel Cords may be Exposed/FMVSS 119 - Bridgestone & Firestone

Hyundai Translead
September 17, 2019 NHTSA CAMPAIGN NUMBER: 19V658000 Bulkhead may Detach …
Recalls oemdtc September 25, 2019 No Comments

Retrofit Front Area to Strengthen Bulkhead - 2017-2018 Hyundai Translead Duralite HT Flatbed Trailers

IC Bus CE School Bus
April 17, 2020 NHTSA CAMPAIGN NUMBER: 20V220000 Fuel Heater May Overheat …
Recalls oemdtc April 22, 2020 No Comments

Fuel Heater May Overheat and Cause Fire - 2017-2021 IC Bus CE School Buses

Van Hool TD925
March 30, 2018 NHTSA CAMPAIGN NUMBER: 18V209000 Seat Belt Buckle Casings …
Recalls oemdtc April 7, 2018 No Comments

Seat Belt Buckle Casings may Fail - 2015-2018 Van Hool Motorcoaches

International WorkStar
March 20, 2019 Engine Fuel Heater May Overheat and Cause …
Recalls oemdtc April 24, 2019 No Comments

Engine Fuel Heater May Overheat and Cause Fire - 2017-2020 International & IC Bus

About The Author

oemdtc

Tags:2016 2017 2018 2019 2020 CS1270GT CS1273GT CS870GT CS873GT CV1273GT CV1273SGT Lamps LP1273XDT Reflectors Trailers Vac-Tron Vacuum Excavator

Leave a Reply Cancel Reply

CAPTCHA
Refresh

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Search

Categories

Amazon Affiliate WordPress Plugin - Automatic Product Boxes and Bestseller-Lists for your blog

Archives

Newsletter

oemdtc

Recalls & Diagnostic Tips

File a Vehicle Safety Complaint with NHTSA


https://www-odi.nhtsa.dot.gov/VehicleComplaint/


VIN Decoder


https://vpic.nhtsa.dot.gov/decoder/Decoder
 
OEMDTC is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
  • Privacy Policy
  • Disclaimer
  • About
Copyright © 2021 oemdtc
Theme by MyThemeShop.com