NHTSA ID Number: 10108970
Manufacturer Communication Number: 0599-899-00_Rev
Summary
Front Pivot Bushing Installation Instructions Update
1 Affected Product
Equipment
BRAND | PART NO. | PRODUCTION DATES |
DEXTER | DEXTER |
INSTALLATION INSTRUCTIONS
Front Pivot Bushing
K71-734-00 Front Pivot Bushing Replacement Kit for one Airflex® Axle
Notice to Buyer
It is recommended that both pivot bushings be replaced at the same time to ensure continued axle alignment. Additionally, each side needs to be replaced while the other side remains intact to maintain control over the suspension components.
Safety Precautions
It is recommended that if you are unfamiliar with this type of work, you should refer to a qualified service center specializing in trailer suspensions. It is also recommended that if you choose to do this yourself, that a factory service manual be obtained for the proper procedures pertaining to removal, replacement and proper torque specifications for your vehicle. This instruction set is intended as a guideline for the safe installation of Dexter’s polyurethane bushings, once you have removed the factory components from your vehicle.
CAUTION |
Do not lift or support the trailer on any part of the axle or suspension system. Never go under any trailer unless it is properly supported on jack stands which have been rated for the load. Improperly supported vehicles can fall unexpectedly and cause serious injury or death. |
Pivot Bushing Replacement
Disassemble ¾" nut and bolt. Remove original rubber/polyurethane bushings (you may need a punch for this) and clear the Airflex® joint of any old rubber or rust. When installing polyurethane bushings, apply grease as instructed.
- Apply light coat of grease to inside of the axle bracket sleeve.
- Apply light coat of grease to the inside and outside of the bushing (all parts that contact metal).
- Apply light coat of grease to the outside of the sleeve.
- Apply light coat of grease to the faces of the bushings after they are installed.
Torque the ¾” pivot bolts to 270-280 Ft. Lbs. to prevent bushing wear and/or suspension damage.
059-899-00 Rev. C
0599-899-00_Rev
https://www.nhtsa.gov/recalls?nhtsaId=10108970
https://static.nhtsa.gov/odi/tsbs/2017/MC-10108970-9999.pdf
- Condition: Aftermarket 100% Brand New
- Compatible with: Fit for all Harley touring models 1994-2018
- Fully Collapsed approx. 9.64inches(24.5cm); fully extended 14.17inches(36cm).
- This kit will allow you to lower your bike 2 to 3 inches with all of the air released.
- Package Contents: One Air Ride Kit (As shown on the first picture)
- Air springs are built like a tire, reinforced with durable 2-ply fabric for maximum strength
- Easy to install With fully-illustrated installation manual
- End caps made of Ultra high-strength corrosion-proof nylon composite which is as strong as steel but weighs less
- Jounce bumper inside the air spring absorbs shock and can be safely run with zero air pressure* (*maintain minimum air Pressure for the ultimate ride comfort)
- Fully adjustable air springs level your vehicle when towing or hauling a heavy load for a safe comfortable ride
- Eliminate sag and bottoming out. More even tire wear: when weight is evenly distributed to all four tires, tires wear more evenly.Always add pressure to the air springs in small quantities, checking the pressure frequently
- Rugged durable components including air springs and all hardware; 2 air springs
- Easy to install with included instructions. Fits many 3/4 ton and 1 ton pickups and vans
- Up to 5000 pounds of leveling capacity; 14.5 x 11.25 x 9.5 inches.Fits single rear wheel (SRW) and dual rear wheel (DRW) models
- Fully adjustable air springs level your vehicle when towing or hauling a heavy load for a safe comfortable ride
- Installs inside coil spring to eliminate sag and bottoming out
- Rugged durable components including air springs and all hardware
- Easy to install with included instructions
- Up to 1000 pounds of leveling capacity
- Viair Authentic 444C Single Chrome Compressor 200 PSI Max
- Comes with Compressor, Filter Mount, Extra Filters & Mounting Hardware.
- Does not come with any relay, Pressure switch or wiring****
- Comes with 1 Year Manufacturer Warranty against all types of Manufacturing defects only
- 【Easy to use】Feature:Reduce poor braking and steering,Eliminate rough ride,Better sound isolation and lower resonance frequency.
- 【Good Quality】Please doublecheck above compatibility list to make sure it fits your vehicle.
- Fit For Hummer H2 2003-2009, OEM 15938306
- Package included: 1 x hummer h2 Air Ride Suspension
- 1 Year Warranty, Brand new!
- Air Ride Suspension Front Bag Bracket Kit
- Fits 1963-1987 Chevy C10 2wd Truck
- Vehicle Specific Front Bag Mounting Brackets Only (no bags)
- Made In USA - Powder Coated Black
Last update on 2021-01-18 / Affiliate links / Images from Amazon Product Advertising API
Last update on 2021-01-18 / Affiliate links / Images from Amazon Product Advertising API