“This site contains affiliate links for which OEMDTC may be compensated” |
June 14, 2019 NHTSA CAMPAIGN NUMBER: 19V452000
Turn Signals May Illuminate with Stop/Tail Lights
Rear Turn signals that illuminate at the same time as the brake lights may create confusion and impair the effectiveness of the brake lights, increasing the risk of a crash.
NHTSA Campaign Number: 19V452
Manufacturer PACCAR Incorporated
Components EXTERIOR LIGHTING
Potential Number of Units Affected 343
Summary
PACCAR Incorporated (PACCAR) is recalling certain 1990-2020 Peterbilt 320 and 520 vehicles built with specific amber rear turn signals. The turn signals may also light up with the stop/tail lights when the brakes are applied. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, “Lamps, Reflective Devices, and Associated Equipment.”
Remedy
PACCAR will notify owners, and for trucks with rear amber lights, dealers will add a jumper harness between the chassis electrical harness and amber tail lights, free of charge. The recall began August 1, 2019. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR’s number for this recall is 19PBC.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Federal Recall Information
19PBC
What’s New
Non-Conforming Safety Recall – Model 320/520 Vehicles with Amber Stop Lamps That Do Not Meet
FMVSS108
Supplier
Description
Model 320/520 Vehicles with Amber Stop Lamps That Do Not Meet FMVSS108
Release Date
6/28/2019
Introduction
Peterbilt Motors Company has determined that certain Model Year 1990-2020 Model 320/520 vehicles manufactured between June 17, 1989 and April 06, 2019 fail to conform to Federal Motor Vehicle Safety Standard (FMVSS/CMVSS) No. 108 – Table 1-a requirements, which require two red stop lamps.
Amber stop lamps may activate when the brake is applied, which may confuse other drivers and contribute to an accident.
Resolution
Service all affected chassis that enter your dealership, even if the customer has no issue with the chassis.
- Review the attached chassis list for your dealer code and schedule your customer(s) for service if their chassis is on the list.
- If you are not using Service Management to start repair orders, review DWWC or SIR for “Complete” next to the “19PBC” campaign code prior to performing this repair.
- Follow the procedures below to remove the amber lights and wiring.
It is a violation of Federal law for a dealer to sell or lease new vehicles covered by this recall until the defect or noncompliance has been corrected.
Warranty
There is no time or mileage limit for this recall.
Peterbilt will pay for parts at dealer net plus applicable mark up and labor:
- 4 hours labor to remove the amber lights and associated wiring. Use Quick Claim Code 19PBC.
- File an additional long form claim for extraordinary circumstances. A quick claim for standard labor must be filed first.
For Field… | Enter… |
Failure Location | 034-004-013 |
Failure Type | 705 |
Claim Type | C |
Responsibility | 09 – Campaign |
Campaign Number | 19PBC |
SRT 034-022 | 0.4 hours to remove both amber lights and jumper. |
Take off parts disposition: Destroy take off parts once claim has been paid.
Parts
There are no parts for this recall.
Procedure
- Review to see if the amber lights are still on the chassis. If not, no further action required.
- If amber lights illuminate when the brake is applied, follow the steps below.
- Remove the amber lights and jumper harness between the chassis electrical harness.
- Ensure the red stop lamps are connected to the chassis electrical harness.
- Ensure the red stop lamps function properly.
Attachments
Chassis List
Customer Letters
Authored by: DKH
July 30, 2019
IMPORTANT SAFETY RECALL
This notice applies to your vehicle. Your VIN(s) can be found on the bottom or back of this page.
Subject: | Safety Recall 19PBC – Model 320/520 Amber Stop Light Issue NHTSA # 19V – 452 EXPIRATION DATE: NONE |
Dear Peterbilt Customer,
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Peterbilt has decided that certain Model 320 and 520 vehicles manufactured between June 17, 1989 and April 06, 2019 fail to conform to Federal Motor Vehicle Safety Standard No. 108. These vehicles include amber stop lamps that illuminate simultaneously with red stop lamps when the brake is applied. The amber stop lamps may confuse other drivers and cause a vehicle crash without prior warning. Your vehicle has been identified as having amber stop lamps.
The problem is… | Amber stop lamps may illuminate when the brake is applied. |
What your dealer will do… | Dealer will inspect and if necessary remove the amber lamps and wiring |
What you must do … | Contact your nearest Peterbilt dealer to schedule an appointment |
Your Peterbilt dealer is available immediately to remedy this issue at no cost to you. To find your Peterbilt dealer, please visit Dealer Locator at www.Peterbilt.com. This repair may take up to 1.0 hours of labor depending on dealer scheduling.
If you had this repair performed before receiving this letter, you may be eligible to receive reimbursement for the cost of obtaining a prenotification remedy of the problem associated with this recall. Receipts for parts and/or labor are required for consideration of reimbursement.
If you require further information about this recall, reimbursement of a pre-notification remedy associated with this recall, or experience any difficulty in making arrangements for this repair, please contact: Peterbilt Motors Company, 1700 Woodbrook St, Denton, TX 76205, Attn: Customer Services Department, phone 940-591-4220.
If you conclude that Peterbilt Motors Company has not enabled you to remedy this defect within a reasonable time and without charge, you may submit a complaint to: Administration for Safety Assurance, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington DC 20590, or call the toll free safety hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to www.safecar.com.
Federal regulation requires that any vehicle lessor receiving this recall notice must forward a copy of it to the lessee within ten days of receipt. If you no longer own this vehicle, we would appreciate you advising Peterbilt of the current owner’s name.
We apologize for any inconvenience, and thank you for your participation in helping Peterbilt provide the highest levels of customer satisfaction and service expertise.
We value your business and appreciate your ongoing loyalty to Peterbilt and its dealer network. Industry-leading quality, performance, and reliability are hallmarks of Peterbilt products, and we thank you for making Peterbilt your truck of choice.
Sincerely,
Michelle Ponsonby
Director of Customer Service
Peterbilt Motors Company
62 Affected Products
Vehicles
MAKE | MODEL | YEAR |
PETERBILT | 320 | 1990-2020 |
PETERBILT | 520 | 1990-2020 |
7 Associated Documents
Recall Quarterly Report #3, 2020-1
RCLQRT-19V452-2991.PDF 211.324KB
Recall Acknowledgement
RCAK-19V452-4128.pdf 245.583KB
Defect Notice 573 Report
RCLRPT-19V452-2717.PDF 212.867KB
Manufacturer Notices(to Dealers,etc)
RCMN-19V452-3619.pdf 353.677KB
ISSUED Owner Notification Letter(Part 577)
RCONL-19V452-9913.pdf 198.688KB
Recall Quarterly Report #2, 2019-4
RCLQRT-19V452-1125.PDF 211.244KB
Recall Quarterly Report #1, 2019-3
RCLQRT-19V452-4061.PDF 211.142KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V452&docType=RCL
- LIGHTS DIM OVER TIME, REPLACE IN PAIRS: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind.
- EASY TO REPLACE: Sylvania Long Life miniature bulbs are easy to install and show instant results.
- LOW MAINTENANCE AND HIGH DURABILITY: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting.
- LONGER LIFE THAN MOST STANDARD BULBS: Long Life bulbs perform twice as long as any other standard miniature bulbs.
- THE SYLVANIA STANDARD OF QUALITY: With 100+ years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket.
- (Set of 2 Bulbs) 54SMD 3014 & 3SMD 3030 high brightness chips per bulb, Working Voltage: 9v-30v.
- Fits: 3056 3057 3057K 3057LL 3155 3157 3157K 3157NA 3157NAK 3157LL 3156NA 3156A 3156 3156K 3357 3357K 3357KNA 3357LL 3457 3457-NA 3457K 3457NAK 3757AK 3757ALL 4057 4057LL 4057K 4114 4114LL 4114K 4157 4157LL 4157K 4157NA 4157NAK 5702A 5702AK 5702AK etc. Easy installation, plug and play.
- Application: Brake Lights, Tail Lights etc. Load resistor or flash relay might be needed to prevent the hyper flash when replacement for Turn Signal Lights.
- Advantage: Compatible for both CK/SRCK and Standard socket, non-polarity design. 300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution,built in Constant Current IC for Longer life span & Low Power Consumption.
- Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you.
- Non-polarity. Can be used for brake lights, tail lights, stop lights, parking light, daytime running light, etc. Some sensitive vehicles will meet canbus issue after installing, load resistors or flasher relay will be required to solve these issues, you can contact us through Amazon Buyer Message to get help and solutions
- Low power and high brightness. 5.5W per 7443 led red bulb. Only 1/4 energy consumption of original 7443 red bulb but 4 times brighter. Built in smart IC driver ensure constant current, no radio interference. Plus instant-on capability with zero warm-up time
- Unique imitated halogen shape design. Resembling halogen bulb shape design and sequencing 54 pieces 4014-SMD LED chips precisely around the light. Delivering 360° high luminous efficiency with full amber light, easier to be noticed and safer to drive
- Small size comparable to OEM 7440 bulbs Non-polarity, applied to US standard and CK sockets. Fits: 992, 7440, 7441, 7443, 7442, 7444, W21W, WY21W, 7440NA, 7440NAK, 7444NA,7444NAK, 7443LL.etc. Amazon filter system may not be 100% accurate or up to date, if you are not sure which bulb model fit your vehicle, please check your vehicle owner manual to confirm or ask a question for help
- Electroplating process housing. Improves oxidation resistance and produces less heat. High-end styling, matching great in the assembly. Ideal replacement for your halogen 7440 red bulbs
- LIGHTS DIM OVER TIME, REPLACE IN PAIRS: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind.
- EASY TO REPLACE: Sylvania Long Life miniature bulbs are easy to install and show instant results.
- LOW MAINTENANCE AND HIGH DURABILITY: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting.
- LONGER LIFE THAN MOST STANDARD BULBS: Long Life bulbs perform twice as long as any other standard miniature bulbs.
- THE SYLVANIA STANDARD OF QUALITY: With 100+ years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket.
- (Set of 2 Bulbs) 54SMD 3014 & 3SMD 3030 high Brightness chips per bulb, Working Voltage: 9v-30v
- Fits: 7440A 7440NA 7440 7440SV 7443NA 7441 7443 7443R 7444 992 WY21W W21/5W W21W etc. Easy installation, plug and play.
- Application: Brake Lights, Tail Lights, Stop Lights, Daytime Running Lights, Fog Lights etc. Load resistor or flash relay might be needed to prevent the hyper flash when replacement for Turn Signal Lights.
- Advantage: Compatible for both CK/SRCK and Standard socket, non-polarity design. 300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution, built in Constant Current IC for Longer life span & Low Power Consumption.
- Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you.
- Resembling halogen bulb shape design and sequencing 54 pieces 4014-SMD LED chips precisely around the 3157 led bulb. Delivering 360° high luminous efficiency with full brilliant red light, more visible when braking
- 5.5W per 3157 red bulb. Only 1/4 energy consumption of original bulb but 4 times brighter. Built in smart IC driver ensure constant current, no radio interference. Plus instant-on capability with zero warm-up time
- Electroplating process housing. Improve oxidation resistance and produce less heat. High-grade shape, matching great in the assembly. Ideal replacement for your halogen bulbs
- Small size comparable to OEM bulbs. Non-polarity, applied to US standard and CK sockets. Can be used for turn signal bulb, side marker light bulb, blinker light bulb, parking lights, etc. Fits: 3056 3156 3157 3157K 3057R 4057 4157, etc.
- Amazon filter system may not be 100% accurate or up to date, if you are not sure which bulb model fit your vehicle, please check your owner manual to confirm or ask a question for help
- (Set of 2 W2.5x16q D.F. wedge base 3156/3157 red LED bulbs) LED Chips: Each 3156/3157 LED red bulb is equipped with 39 pieces high quality, high power with high performance led chips per 3156 3157 LED bulb, 360° full angle illumination with projector lens design
- Important: Extra LED resistors maybe required to avoid the signal hyper flash or error code for LED bulbs draw less current than stock lamps. Compatible with both standard and CK / SRCK type. Voltage: 12V~14.8V, Built in stable current IC driver for longer lifespan. Color: Pure red.
- Dual filament LEDs are universal fit for single filament and dual filaments T25 wedge base bulbs. Non-polarity. Cross reference number: 3156, 3056, 3047, 3047LL, 3047K, 3055, 3057, 3057ST, 3057K, 3057KX, 3057X, 3057KLCP, 3057LL, 3155, 3155LL, 3157 ,3157K, 3157X, 3157LL, 3157ST, 3157KX, 3357, 3357LL, 3357K, 3457, 3457K, 4057, 4057LL, 4057K, 4114, 4114LL, 4114K, 4157, 4157LL, 4157K, 4157NA, p27/7w, 3157/40610, 3157/17172, 12450004, 78633, 17945, 3156/21863, 9442003, 78625, 17941, etc.
- Application: Used for upgrading OEM dim incandescent or damaged rear turn signals, directional blinker lamps, brake stop tail lights, taillights, rear side marker light amp for much safer driving and luxury looking for automotive cars, trucks, motorcycles, SUVs, vans.
- Newly upgraded smart IC driver for better performance and longer lifespan. USA located.
- (Set of 2) Newly upgraded version, built-in USA-made smart IC driver for the best light performance and longer lifespan, 7443 Strobe led lights bulbs flash 3 times on-and-off and then keep solid light (Legal blinking times) to avoidthe rear-end collision for automotive cars, trucks, SUVs, RVs.
- LED Chips: Each 7443 LED strobe bulb is equipped with 39 pieces high quality,high power and high performance 2835 led chips; 360° full angle illumination light ouput with projector lens.
- Universal fits T20 wedge 7440 single filament and 7443 dual filament W3x16Q base, big difference between high and low intensity light output, replacing rear 7440 7443 brake stop light, back-up reverse lights, center high-mount stop ( 3rd brake ) lights lamps,etc. Extra load resistors maybe required to avoid the error code or blinking issue.
- The length is about 2.09 inch. Cross reference number: 7440, 7441, 7443, 7443LL, W21/5W, 7443/26201, 78660, 78661, 17919, 7515, HIB7443WM, W21W, 7440/26200, 17632, 7504, 7440LL, 7443-SRCK, 7443-CK,etc.
- One Year Warranty Compatible with both standard type and CK/SRCK type. Voltage: 12V - 24V, built-in stable current IC driver for longer lifespan.
- Twice The Life Of Standard Incandescent Bulbs
- Philips Offers A Wide Range Of Smart Light Bulbs, Lamps, Fixtures And Accessories
- Original Equipment Quality Seal For The Most Reliable Performance
- Always Replace In Pairs To Ensure A Symmetric Light Beam From Both Bulbs On The Road. Bulbs Dim Over Time
- twice the life of standard incandescent bulbs
- best value
- original equipment quality seal for the most reliable performance
- always replace in pairs to ensure a symmetric light beam from both bulbs on the road. bulbs dim over time.
- miniature bulbs by philips, for over 100 years we have been continuously innovating automotive lighting
Last update on 2024-04-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.