MT Chassis

FL814 – FCCC MT Chassis Brake Pedal Clevis Pins – 2012-2019 Freightliner Custom Chassis MT55 & MT45

by
“This site contains affiliate links for which OEMDTC may be compensated”

May 14, 2019 NHTSA CAMPAIGN NUMBER: 19V371000

Brake Pedal Clevis Pin Clip May Detach

If the clip is detaches and clevis pin slides out of position, the brake lights may fail. Loss of brake lights may mislead other drivers if they are unaware the vehicle is stopping or slowing down, which increases the risk of crash. If the pin continues to slide out further, the pedal may detach, increasing the risk of crash.

 

NHTSA Campaign Number: 19V371

Manufacturer Daimler Trucks North America LLC

Components SERVICE BRAKES, HYDRAULIC, EXTERIOR LIGHTING

Potential Number of Units Affected 9,702

 

Summary

Daimler Trucks North America LLC (DTNA) is recalling certain 2012-2019 Freightliner Custom Chassis MT55 and MT45 vehicles. The brake pedal clevis pin clip may rub or bend on the throttle pedal and possibly detach.

 

Remedy

DTNA will notify the vehicle manufacturers that purchased these chassis, and DTNA dealers will inspect the clevis pin clearance and correct it as necessary, free of charge. DTNA issued owners an interim notification on July 12, 2019. The recall began August 28, 2019. Owners may contact DTNA customer service at 1-800-547-0712. DTNA’s number for this recall is FL-814.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check for Daimler Trucks North America Recalls

 

Recall Campaign

September 2019
FL814A-E
NHTSA #19V-371
REVISED NOTICE

Subject: FCCC MT Chassis Brake Pedal Clevis Pins

Models Affected: Specific Freightliner Custom Chassis MT45 and MT565 step vans, manufacturedJanuary 12, 2011, through January 3, 2019.

 

General Information

Daimler Trucks North America LLC (DTNA), on behalf of it’s wholly-owned subsidiary Freightliner Custom Chassis Corporation, has decided that a defect that relates to motor vehicle safety exists on the vehicles mentioned above.

There are approximately 10,418 vehicles involved in this campaign.

The clearance between the brake pedal clevis pin clip and the throttle pedal mounting hardware does not meet minimum clearance requirements. This could result in detachment of the brake pedal clevis pin clip. As the clevis pin works out, there will initially be loss of brake lights, and eventually the brake pedal may become detached. Both the loss of brake lights and a detached brake pedal increase the risk of a crash.

The throttle pedal assembly will be replaced with a new design to create additional clearance between the brake pedal clevis pin and the throttle pedal mounting hardware. Freightliner Custom Chassis Engineering has determined that one of the bolts used in the original repair was incorrect. Vehicles that have had FL814 completed are being notified to return to have this corrected.

REVISION:Two new groups, FL814D and FL814E, have been added to the recall. A procedure for new groups has been added, the callouts for Fig. 1 have been revised, the parts table has been revised, and an SRT has been added.

Additional Repairs

Dealers must complete all outstanding Recall and Field Service campaigns prior to the sale or delivery of a vehicle. A Dealer will be liable for any progressive damage that results from its failure to complete campaigns before sale or delivery of a vehicle.

Owners may be liable for any progressive damage that results from failure to complete campaigns within a reasonable time after receiving notification.

 

Work Instructions

Please refer to the attached work instructions. Prior to performing the campaign, check the vehicle for a completion sticker (Form WAR260).

 

Replacement Parts

Replacement parts are now available and can be obtained by ordering the part numbers listed below from your facing Parts Distribution Center.

If our records show your dealership has ordered any vehicles involved in campaign number FL814, a list of the customers and vehicle identification numbers will be available in OWL. Please refer to this list when ordering parts for this recall.

Table 1 – Replacement Parts for FL814

Campaign Number Part Number Part Description Qty.
FL814A-C 01-34563-000 BRKT-MTG,ACLTR PEDAL,TOP 1 ea
01-34564-000 BRKT-MTG,ACLTR PEDAL,BTM 1 ea
23-09114-002 WASHER-HRDN,0.41X0.81X.080,ZN 2 ea
23-09114-006 WASHER-HRDN,0.34X0.69X.080,ZN 12 ea
23-11745-125 SCREW-CAP,HEX,GR8,5/16-18X1.25 6 ea
23-11747-150 SCREW-CAP,HEX,3/8-16,G 1 ea
23-13833-106 NUT-HEX,PT,3/8-16,ZN/AL,C,.337 1 ea
23-13861-105 NUT-HEX,FLG,LOCK,5/16-18,ZN AL 6 ea
A01-34567-000 PEDAL ASSY-ACLTR,CUMMINS 1 ea
TDA 2257D1174 PIN-HITCH (Clip),.072X1.26,MER ASA 1 ea
WAR260 BLANK COMPLETION STICKER 1 ea
FL814D,E 23-11747-150 SCREW-CAP,HEX,3/8-16,G 1 ea
23-13833-106 NUT-HEX,PT,3/8-16,ZN/AL,C,.337 1 ea

 

Table 1

 

Removed Parts

U.S. and Canadian Dealers, please follow Warranty Failed Parts Tracking shipping instructions for the disposition of all removed parts. Export distributors, please destroy removed parts unless otherwise advised.

 

Labor Allowance

Table 2 – Labor Allowance

Campaign Number Procedure Time Allowed (hours) SRT Code Corrective Action
FL814A,C Replace Throttle Pedal Assembly 0.4 996-R069A 12-Repair Recall/Campaign
FL814B Replace Throttle Pedal Assembly and Reorient Clevis Pin 0.5 996-R069B 12-Repair Recall/Campaign
FL814D,E Replace Throttle Pedal Bolt and Nut 0.2 996-R069D 12-Repair Recall/Campaign

 

Table 2

IMPORTANT: When the Recall has been completed, locate the base completion label in the appropriate location on the vehicle, and attach the red completion sticker provided in the recall kit (Form WAR260). If the vehicle does not have a base completion label, clean a spot on the appropriate location of the vehicle and first attach the base completion label (Form WAR259). If a recall kit is not required or there is no completion sticker in the kit, write the recall number on a blank sticker and attach it to the base completion label.

 

Claims for Credit

You will be reimbursed for your parts, labor, and handling (landed cost for Export Distributors) by submitting your claim through the Warranty system within 30 days of completing this campaign. Please reference the following information in OWL:

  • Claim type is Recall Campaign.
  • In the Campaign field, enter the campaign number and appropriate condition code (e.g. FL814-A, FL814-B, etc.).
  • In the Primary Failed Part Number field, enter 25-FL814-000.
  • In the Parts field, enter the appropriate part numbers as shown in the Replacement Parts Table.
  • In the Labor field, first enter the appropriate SRT from the Labor Allowance Table. Administrative time will be included automatically as SRT 939-6010A for 0.3 hours.
  • The VMRS Component Code is F99-999-005 and the Cause Code is A1 – Campaign.
  • U.S. and Canada — Reimbursement for Prior Repairs. When a customer asks about reimbursement, please do the following:
  • Accept the documentation of the previous repair.
  • Make a brief check of the customer’s paperwork to see if the repair may be eligible for reimbursement. (See the “Copy of Owner Letter” section of this bulletin for reimbursement guidelines.)
  • Submit an OWL Recall Pre-Approval Request for a decision.
  • Include the approved amount on your claim in the Other Charges section.
  • Attach the documentation to the pre-approval request.
  • If approved, submit a based on claim for the pre-approval.
  • Reimburse the customer the appropriate amount.

IMPORTANT: OWL must be viewed prior to performing the recall to ensure the vehicle is involved and the campaign has not been previously completed. Also, check for a completion sticker prior to beginning work.

U.S. and Canadian dealers, contact the Warranty Campaigns Department via Web inquiry at DTNAConnect.com / WSC, or the Customer Assistance Center at (800) 385-4357, after normal business hours, if you have any questions or need additional information. Export distributors, submit a Web inquiry or contact your International Service Manager.

U.S. and Canadian Dealers: To return excess kit inventory related to this campaign, U.S. dealers must submit a Parts Authorization Return (PAR) to the Memphis PDC. Canadian dealers must submit a PAR to their facing PDC. All kits must be in resalable condition. PAR requests must include the original purchase invoice number. Export Distributors: Excess inventory may be returned as noted for U.S. and Canadian dealers. Export locations will pay freight to return kits. Export Distributors: Excess inventory is not returnable.

The letter notifying U.S. and Canadian vehicle owners is included for your reference.

Please note that the National Traffic and Motor Vehicle Safety Act, as amended (Title 49, United States Code, Chapter 301), requires the owner’s vehicle(s) be corrected within a reasonable time after parts are available to you. The Act states that failure to repair a vehicle within 60 days after tender for repair shall be prima facie evidence of an unreasonable time. However, circumstances of a particular situation may reduce the 60 day period. Failure to repair a vehicle within a reasonable time can result in either the obligation to (a) replace the vehicle with an identical or reasonably equivalent vehicle, without charge, or (b) refund the purchase price in full, less a reasonable allowance for depreciation. The Act further prohibits dealers from selling a vehicle unless all outstanding recalls are performed. Any lessor is required to send a copy of the recall notification to the lessee within 10 days. Any subsequent stage manufacturer is required to forward this notice to its distributors and retail outlets within five working days.

Copy of Notice to Owners

Subject: FCCC MT Chassis Brake Pedal Clevis Pins

For the Notice to U.S. Customers: This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. For the Notice to Canadian Customers: This notice is sent to you in accordance with the requirements of the Motor Vehicle Safety Act. This is to inform you that your vehicle may contain a defect that could affect the safety of a person.

Daimler Trucks North America LLC (DTNA), on behalf of its wholly owned subsidiary Freightliner Custom

Chassis Corporation, has decided that a defect that relates to motor vehicle safety exists on specific Model Year 2011-2019 Freightliner Custom Chassis MT45 and MT55 step vans, manufactured January 12, 2011, through January 3, 2019.

The clearance between the brake pedal clevis pin clip and the throttle pedal mounting hardware does not meet minimum clearance requirements. This could result in detachment of the brake pedal clevis pin clip. As the clevis pin works out, there will initially be loss of brake lights, and eventually the brake pedal may become detached. Both the loss of brake lights and a detached brake pedal increase the risk of a crash.

The throttle pedal assembly will be replaced with a new design to create additional clearance between the brake pedal clevis pin and the throttle pedal mounting hardware.

Please contact an authorized Daimler Trucks North America dealer to arrange to have the Recall performed and to ensure that parts are available at the dealership. To locate an authorized dealer, search online at

Daimler-TrucksNorthAmerica.com. On the menu tab, select “Contact Us,” scroll down to “Locate a Dealer,” and select the appropriate brand. The Recall will take approximately one hour and will be performed at no charge to you. You may also confirm your vehicle’s involvement in this recall at URL: https:// dtna-dlrinfo.prd.freightliner.com:48518/VinLookup/vin-module/getVinLookupPage

You may be liable for any progressive damage that results from your failure to complete the Recall within a reasonable time after receiving notification.

If you do not own the vehicle that corresponds to the identification number(s) which appears on the Recall Notification, please return the notification to the Warranty Campaigns Department with any information you can furnish that will assist us in locating the present owner. If you have leased this vehicle, Federal law requires that you forward this notice to the lessee within 10 days. If you are a subsequent stage manufacturer, Federal law requires that you forward this notice to your distributors and retail outlets within five working days. For the Notice to U.S. Customers: If you have paid to have this recall condition corrected prior to this notice, you may be eligible to receive reimbursement. Please see the reverse side of this notice for details.

For the Notice to U.S. Customers: If you have questions about this Recall, please contact the Warranty Campaigns Department at (800) 547-0712, 7:00 a.m. to 4:00 p.m. Pacific Time, Monday through Friday, e-mail address DTNA.Warranty.Campaigns@Daimler.com. If you are not able to have the defect remedied without charge and within a reasonable time, you may wish to submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE., Washington, DC 20590; or call the Vehicle Safety Hotline at (888) 327-4236 (TTY: 800-424-9153); or go to https://www.safercar.gov. For the Notice to Canadian Customers: If you have questions about this Recall, please contact the Warranty Campaigns Department at (800) 547-0712, 7:00 a.m. to 4:00 p.m. Pacific Time, Monday through Friday, e-mail address DTNA.Warranty.Campaigns@Daimler.com.

We regret any inconvenience this action may cause but feel certain you understand our interest in motor vehicle safety.

WARRANTY CAMPAIGNS DEPARTMENT

Enclosure

Reimbursement to Customers for Repairs Performed Prior to Recall

If you have already paid to have this recall condition corrected you may be eligible to receive reimbursement.

Requests for reimbursement may include parts and labor. Reimbursement may be limited to the amount the repair would have cost if completed by an authorized Daimler Trucks North America LLC dealer. The following documentation must be presented to your dealer for consideration for reimbursement.

Please provide original or clear copies of all receipts, invoices, and repair orders that show:

  • The name and address of the person who paid for the repair
  • The Vehicle Identification Number (VIN) of the vehicle that was repaired
  • What problem occurred, what repair was done, when the repair was done
  • Who repaired the vehicle
  • The total cost of the repair expense that is being claimed
  • Proof of payment for the repair (such as the front and back of a cancelled check or a credit card receipt) Reimbursement will be made by check from your Daimler Trucks North America LLC dealer.

Please speak with your Daimler Trucks North America LLC authorized dealer concerning this matter.

Copy of Notice to Owners

Subject: FCCC MT Chassis Brake Pedal Clevis Pins

This letter is to notify you that your vehicle requires additional work as part of recall FL814. Freightliner Custom Chassis Engineering has determined that one of the parts used in the original repair was incorrect.

Please contact an authorized Daimler Trucks North America dealer to arrange to have this work performed and to ensure that parts are available at the dealership. To locate an authorized dealer, search online at www.Daimler-TrucksNorthAmerica.com / Contact Us / Locate a Dealer. This will take approximately half an hour and will be performed at no charge to you.

If you do not own the vehicle that corresponds to the identification number(s) which appears on the Recall Notification, please return the notification to the Warranty Campaigns Department with any information you can furnish that will assist us in locating the present owner.

If you have questions about this Recall, please contact the Warranty Campaigns Department at (800) 547-0712, 7:00 a.m. to 4:00 p.m. Pacific Time, Monday through Friday, e-mail address DTNA.Warranty.Campaigns@Daimler.com.

We regret any inconvenience this action may cause but feel certain you understand our interest in motor vehicle safety.

WARRANTY CAMPAIGNS DEPARTMENT

Enclosure

Work Instructions

Subject: FCCC MT Chassis Brake Pedal Clevis Pins

Models Affected: Specific Freightliner Custom Chassis MT45 and MT55 step vans, manufactured from January 12, 2011, through January 3, 2019.

Revisions:Two new groups, FL814D and FL814E, have been added to the recall. A procedure for new groups has been added, the callouts for Fig. 1 have been revised, the parts table has been revised, and an SRT has been added.

 

FL814A-C (includes B) – Throttle Pedal Replacement

  1. Check the base label (Form WAR259) for a completion sticker for FL814 (Form WAR260) indicating this work has been done. The base label is usually located on the front wall under the dash. If a sticker is present, no work is needed. If there is no sticker, proceed with the next step.
  2. Park the vehicle on a level surface, shut down the engine, and set the parking brake. Chock the tires.

NOTE: Two technicians are needed for the next step.

  1. Remove the hardware that attaches the throttle pedal assembly to the firewall.
  2. Remove the throttle pedal assembly.

NOTE: It may be helpful to use a small bladed tool to disconnect the electrical connector.

  1. Disconnect the electrical connector.
  2. Discard the throttle pedal assembly.
  3. Connect the electrical connector.
  4. Using new hardware, install the throttle pedal assembly as shown in Fig. 1.

Fig. 1, Throttle Pedal Assembly

 

8.1  Tighten the nut that attaches the top accelerator mounting bracket to the firewall 19 to 24 lbf·ft (26 to 33 N·m).

8.2 Tighten the six nuts that attaches the bottom accelerator mounting bracket 84 to 120 lbf·in (949 to 1356 N·cm).

  1. For FL814A or FL814C, clean a spot on the base label (Form WAR259). Write the recall number, FL814, on a completion sticker (Form WAR260), and attach it to the base label to indicate this recall has been completed.
  2. For FL814B, go to Brake Pedal Clevis Pin Reorientation (after performing Throttle Pedal Replacement).

 

FL814B – Brake Pedal Clevis Pin Reorientation

(After performing Throttle Pedal Replacement)

  1. Remove the hitch clip from the clevis pin.
  2. Remove the clevis pin from the brake pedal.
  3. Install the clevis pin on the left side of the brake pedal. See 2.
  4. Install the hitch clip on the clevis pin. See 2.

Fig. 2, Reorientation of the Clevis Pin and Hitch Clip

  1. With the vehicle parked, depress the brake pedal to ensure there is clearance with the throttle pedal assembly. If there is not, contact Freightliner Custom Chassis Corporation at 1-800-385-4357.
  2. Clean a spot on the base label (Form WAR259). Write the recall number, FL814, on a completion sticker (Form WAR260), and attach it to the base label to indicate this recall has been completed.

 

FL814D,E – Throttle Pedal Bolt Replacement

NOTE: Perform this procedure even if a completion sticker for FL814 is present.

  1. Park the vehicle on a level surface, shut down the engine, and set the parking brake. Chock the tires.

NOTE: Two technicians are needed for the next two steps.

  1. Remove and discard the top throttle pedal to firewall bracket bolt and nut; set the washers aside for later use.
  2. Install the new bolt and nut, as well as the washers set aside in the previous step. Tighten the bolt 19 to 24 lbf·ft (26 to 33 N·m).
  3. If the holes between the bracket and firewall do not align, slightly loosen the top two throttle pedal bolts to allow the bracket to move, so that the holes align at the firewall.
  4. Tighten the top two throttle pedal bolts 84 to 120 lbf·in (949 to 1356 N·cm).
  5. Clean a spot on the base label (Form WAR259). Write the recall number, FL814, on a completion sticker (Form WAR260), and attach it to the base label to indicate this recall has been completed.

16 Affected Products

Vehicles

MAKE MODEL YEAR
FCCC MT45 2012-2019
FCCC MT55 2012-2019

 

18 Associated Documents

Miscellaneous Document- Body Builders Notice

RMISC-19V371-5807.pdf 743.329KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [725.91 KB]

 

Defect Notice 573 Report

RCLRPT-19V371-5048.PDF 213.592KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.59 KB]

 

Miscellaneous Document- 573 Defect Information Report

RMISC-19V371-7666.pdf 428.069KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [418.04 KB]

 

Recall Acknowledgement

RCAK-19V371-3266.pdf 244.967KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [239.23 KB]

 

Remedy Instructions and TSB

RCRIT-19V371-1257.pdf 117.791KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [115.03 KB]

 

Remedy Instructions and TSB

RCRIT-19V371-3714.pdf 118.589KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [115.81 KB]

 

Miscellaneous Document- 2019-4 Quarterly Report Breakdown

RMISC-19V371-4460.pdf 439.973KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [429.66 KB]

 

ISSUED Owner Notification Letter(Part 577)

RCONL-19V371-1154.pdf 53.292KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [52.04 KB]

 

Manufacturer Notices(to Dealers,etc)

RCMN-19V371-5737.pdf 122.47KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [119.60 KB]

 

Recall Quarterly Report #2, 2019-4

RCLQRT-19V371-4916.PDF 211.251KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.30 KB]

 

Recall Quarterly Report #1, 2019-3

RCLQRT-19V371-5690.PDF 211.148KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.20 KB]

 

Miscellaneous Document- List of Body Builders

RMISC-19V371-4634.pdf 842.809KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [823.06 KB]

 

Manufacturer Notices(to Dealers,etc)

RCMN-19V371-6343.pdf 115.549KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [112.84 KB]

 

Interim Owner Notification Letter(Part 577)

RIONL-19V371-1538.pdf 38.241KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [37.34 KB]

 

Manufacturer Notices(to Dealers,etc)

RCMN-19V371-4725.pdf 62.44KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [60.98 KB]

 

Remedy Instructions and TSB

RCRIT-19V371-9905.pdf 126.689KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [123.72 KB]

 

Remedy Instructions and TSB

RCRIT-19V371-7634.pdf 128.942KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [125.92 KB]

 

Miscellaneous Document- Quarterly Report 2019-3 Bodybuilder

RMISC-19V371-1620.pdf 442.395KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [432.03 KB]

 

Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V371&docType=RCL

 

 

“This site contains affiliate links for which OEMDTC may be compensated”
Bestseller No. 1
472795 014973472795 Clevis Pin with R- Clip Fits Home, Farm, Business, automotives (1/4 inch X 2-1/2 inches) 2 Pack
472795 014973472795 Clevis Pin with R- Clip Fits Home, Farm, Business, automotives (1/4 inch X 2-1/2 inches) 2 Pack
  • Size：Diameter: 1/4 inch Length: 2-1/2 inches
  • Material: Steel
  • Includes：2 Clevis Pin With R- Clip
$7.39 Amazon Prime
Buy on Amazon Price incl. tax, excl. shipping
SaleBestseller No. 2
NEIKO 50414A 60 Piece Clevis Pins Assortment Kit, Zinc Construction 3/32”,1/8”, and 5/32” Hole Sizes, 3 Different SAE Sizes, Steel Pin, Single Hole Flat Head Clevis Pins
NEIKO 50414A 60 Piece Clevis Pins Assortment Kit, Zinc Construction 3/32”,1/8”, and 5/32” Hole Sizes, 3 Different SAE Sizes, Steel Pin, Single Hole Flat Head Clevis Pins
  • APPLICATION: Functionally are similar to a bolt, clevis lock is inserted into holes and is used to secure two or more items together. These work great with a trailer, hitches, latches, machinery and utility trailers that require a safety pin clip or cotter pins
  • UNIQUE DESIGN: Strong steel construction allows the single holed clevis pins to handle lateral stress without compromising its quality. Each pin does have a through-hole at the bottom of their shank to allow them to be secured with various locking pins, such as cotter pin, split pin, or a hairpin cotter.
  • VERSATILE: Unthreaded clevis pins have a wide range of versatility for small home do-it-yourself (DIY) projects that utilize the clevis fastener mechanism, which allows free rotation and flexibility of the supported object/application
  • QUALITY: All our clovis pins are zinc coated to protect your tools from oxidation and provide great resistance to corrosion to last long. These hardware pins can be easily installed and disassembled even in narrow spaces, which can save you time and energy.
  • INCLUDED: Our steel pin clevis zinc set comes neatly organized in a divided transparent case for easy storage and high visibility. The assorted set includes three-hole sizes: 3/32" x 26 Pieces, 1/8" x 20 Pieces, and 5/32" x 14 Pieces.
$15.99 −$1.00 $14.99 Amazon Prime
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 3
Boatsea 122Pcs Cotter Pin Hair Pin Clevis Pin Assortment Kit,R Clips Retaining Hair Pins Assortment, Including Single Hole Clevis Pin&Split Cotter Pin&R Clip Hitch Pin for Trailer Latch, Zinc-Plated
Boatsea 122Pcs Cotter Pin Hair Pin Clevis Pin Assortment Kit,R Clips Retaining Hair Pins Assortment, Including Single Hole Clevis Pin&Split Cotter Pin&R Clip Hitch Pin for Trailer Latch, Zinc-Plated
  • Material & Quality: The Boatsea Cotter Pin kit is made of rust - and corrosion-resistant, durable quality spring steel, ensuring a very long service life in any workshop without the need to replace these. ensures a very long life of use in any workshop, no need to replace these. Compared with other ordinary carbon steels, it has stronger mechanical properties, hardenability and other properties.An excellent alternative solution for replacing hitch pins on most equipment.
  • Reasonably Packaged Value Products: The package includes 36 single-hole hole clevis pins in 9 sizes, 43 cotter pins in 3 sizes, 43 R clip pins in 3 sizes (Please see picture for detailed size), a total of 122 pieces to meet your different needs. Convenient see-through resealable storage case packs all material together for portability, organization, and makes it easy to identify size markings which means you can easily find the cotter pin you need.
  • Easy to Use: High quality cotter pin hitch pin assortment kit easy to fit and remove. The clevis pin works together with split cotter pins or r pin hitch. Insert the cotter pin or R pin into the hole of the clevis pin until the head of the pin rests on the bolt, then holds the cotter pin by using pliers to spread the prongs out in the opposite direction, Finally, cut the excess length from either pin as needed. It can quickly and safely fix the bolts and pins, so that your work never shrinks.
  • Wide Applications: Our cotter pin set has 122 pcs in a box that comes in 15 different sizes is widely applied for holding bolts and pins, used for automotive, mechanics, car garage, workshop, power equipment, cars, trucks, lawn mower, small engine repair and fastening. Works great for repairing any mechanical, automotive, or small engine.
  • Quality Assurance: Customer satisfaction is our pursuit. We have full confidence in our products. If you are not satisfied for any reason within 30 days, please return your tool kit without any questions. We also provide 7*24 customer service.
$18.99 Amazon Prime
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 4
Rrina 110Pcs 304 Stainless Steel Flat Head Clevis Pins Cotter Pin Clip Key Assortment Kit Link Hinge T-Shape Round Pin M3 M4 M5 Assorted Sizes Set
Rrina 110Pcs 304 Stainless Steel Flat Head Clevis Pins Cotter Pin Clip Key Assortment Kit Link Hinge T-Shape Round Pin M3 M4 M5 Assorted Sizes Set
  • MATERIAL: Clevis Pins are made with high quality 304 Stainless Steel, not easy to rust, Anti-moisture, Anti-oxiclation, corrosion resistant, acid/alkali resistance for indoor and outdoor use.
  • PACKING QUANTITY: 55Pcs Clevis Pins 15 sizes(M3x10、M3x12、M3x14、M3x16、M3x20、M4x10、M4x12、M4x16、M4x20、M4x25、M5x12、M5x16、M5x20、M5x25，M5x30), 55Pcs Cotter Pin 2 sizes(M1.2x8、M1.7x12).
  • SUITABLE FOR: Clevis Pins are used in a wide variety of fasteners used in farming equipment and sailboat rigging, as well as the automotive, aircraft and construction industries. As a part of a fastener, a clevis provides a method of allowing rotation in some axes while restricting rotation in others.
  • PLASTIC HEAT SEAL PACKAGING: Practical and convenient of packing box, All of Clevis Pins are packed in a durable and sturdy box, this box can be use for a storage box.
  • DURABLE DIVIDED STORAGE CASE: All Clevis Pins are packed in the box with size label and divider, easy to store and won't mix up.
$13.99 Amazon Prime
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 5
2 Pcs 3/8 inch Red Handle Hitch Pin Accessories for Tractors,Clevis Pin 3/8 x 4 Inch
2 Pcs 3/8 inch Red Handle Hitch Pin Accessories for Tractors,Clevis Pin 3/8 x 4 Inch
  • Material: This red handle hitch pin is made of high-strength steel for wear and impact resistance.
  • Hitch Pin Assembly Size:3/8 inch in diameter, available length 4 inches
  • Surface Treatment: This tractor pin is shielded with a durable black powder coating to prevent dust and corrosion.
  • Design: The handle is wrapped in soft rubber for a comfortable fit and easy grip. Plug and play connection, very convenient to use.
  • Accessories: Includes an R-clip. Made of high quality spring steel for durability.
$9.99 Amazon Prime
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 6
Glarks 122Pcs 4 Styles Clevis Pin/Cotter Pin/Hair Pin/Dowel Pin Assortment Set, 15 Size 304 Stainless Steel Pin Fasteners for Automotive, Mechanics, Cars, Trucks, Lawn Mower Use
Glarks 122Pcs 4 Styles Clevis Pin/Cotter Pin/Hair Pin/Dowel Pin Assortment Set, 15 Size 304 Stainless Steel Pin Fasteners for Automotive, Mechanics, Cars, Trucks, Lawn Mower Use
  • ★『What You Get』: Package include 4 styles of clevis pin, cotter pins, dowel pin and R hair pins, 15 sizes total 122pcs are sorted packed in a plastic box for easy store. Enough size and quantity can meet you needs for automotive, mechanics, cars, trucks, lawn mower use.
  • ★『Product Size』: 7 different sizes clevis pin which are m4x35, m6x16, m6x25, m6x35, m8x16, m8x25, m8x35; 3 sizes cotter pin are m1.5x12, m2x20, m3x30; 3 sizes hair pin are m1.5x30, m3x50, m2x40; 2 sizes dowel pin are m4x16, m4x25. Enough quantity and size can meet your different needs.
  • ★『Product Material』: All the pins are made of high quality 304 stainless steel, with strong hardness, rust and corrosion resistant, durable and steady not easy to break.
  • ★『Product Feature』: Our pin fasteners kit contains 4 different styles. Which are precise in size and smooth on the surface, they can be easily installed and disassembled even in narrow spaces. Unique design gives fast and secure hold for bolts and pins, specialty locks to ensure tight hold that will last long.
  • ★『Application』: Nice quality cotter pins and hair pin will firmly hold the bolts in place, perfect used for automotive, mechanics, car garage, workshop, power equipment, cars, trucks, lawn mower and etc.
$19.89 Amazon Prime
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 7
Set of 4 Clevis Pin with R - Clip 472795 014973472795 -1/4X 2-1/2 inches
Set of 4 Clevis Pin with R - Clip 472795 014973472795 -1/4X 2-1/2 inches
  • Replace Number：472795 014973472795
  • Size： Diameter: 1/4 inch Length: 2-1/2 inches
  • Fits：more home, farm, business, automotives,
  • Antirust treatment has been done
  • Include：4 Clevis Pin / Matching R- Clip
$9.69 Amazon Prime
Buy on Amazon Price incl. tax, excl. shipping
SaleBestseller No. 8
CURT 25010 Trailer Coupler Pin, 5/16-Inch Diameter x 3-Inch Long SILVER
CURT 25010 Trailer Coupler Pin, 5/16-Inch Diameter x 3-Inch Long SILVER
  • VERSATILE. The 5/16-inch diameter and 3-inch length of this coupler safety pin make it highly versatile to fit a wide variety of trailer couplers. It can also be used for a trailer jack wheel, pintle hook and more
  • SECURE. This coupler safety pin provides a reliable solution for keeping your trailer coupler latch engaged with the trailer ball. The solid pin offers ample strength while the retainer clip ensures the pin will not vibrate or rattle free
  • EASY TO USE. The square retainer clip of this trailer coupler pin is made with spring steel, making the clip semi-flexible for easy operation. With the safety pin inserted in the coupler latch, the square retainer easily clips on to the end of the pin
  • CORROSION-RESISTANT. Protected by a durable zinc-plated finish, this coupler safety pin maintains excellent resistance to rust and corrosion for longevity and hassle-free use every time
  • HIGH-STRENGTH. The 5/16-inch trailer coupler pin is made out of solid steel for reliable strength, safety on the road and confidence with every mile of your adventure
$2.95 −$1.35 $1.60 Amazon Prime
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 9
Swpeet 122Pcs 304 Stainless Steel M4 M6 M8 Clevis Pin with M1.5 M2 M3 Zinc Plated Steel Cotter Pin and Clips Fastener Set Hitch Pin Clips Fastener Fitting Hole Location Pin T-Shape Round Pin
Swpeet 122Pcs 304 Stainless Steel M4 M6 M8 Clevis Pin with M1.5 M2 M3 Zinc Plated Steel Cotter Pin and Clips Fastener Set Hitch Pin Clips Fastener Fitting Hole Location Pin T-Shape Round Pin
  • ☛ 1, 【 What You Get 】------ In this kit, You will get 8Pcs M5 x25mm / 0.98", 8Pcs M5 x 20mm / 0.79", 8Pcs M5 x 16mm / 0.63", 8Pcs M5 x 12mm / 0.47", 8Pcs M4 x 25mm / 0.98", 8Pcs M4 x 20mm / 0.79", 5Pcs M4 x 16mm / 0.63", 8Pcs M4 x12mm / 0.47", 8Pcs M3 x20mm / 0.79", 8Pcs M3 x 16mm / 0.63", 8Pcs M3 x12mm / 0.47", 8Pcs M3 x 10mm / 0.39", In total 96Pcs, can meet all your daily needs.
  • ☛ 2, 【 With M1.5 M2 M3 Cotter Pins and Hair Pins Assortment Kit 】------ The cotter pin with hair pin style design gives fast and secure hold for bolts and pins, specialty locks to ensure tight hold that will last long, Heavy duty material allows for durability while hair pin style design gives fast and secure hold for bolts to ensure stability.
  • ☛ 3, 【 With M4 M6 M8 Clevis Pin Kit 】------ Unique design and Good quality, T shape, flat head, round structure and exquisite appearance. : Galvanized standardized firmware, rugged, durable, resistant to damage, corrosion resistance, high hardness, flexible positioning.
  • ☛ 4, 【 With Storeage Plastic Box 】 ----- The 122Pcs Pcs 304 stainless steel Clevis Pin Assortment Kit in various sizes and comes in a compartmented plastic case for storage and organization. Each pin has a chamfered end for insertion. The pins are made from l 304 stainless steel for toughness.
  • ☛ 5, 【 The Best faster Choice 】 ------ The pin is a class of standardized fasteners,it is can be static connected, but also to do relative movement with the connector, it mainly applied for the hinge of two parts, and then constitute a hinge connection. Pin usually lock by open pin, safe and reliable, not easy to break off, it's your effective small assistant, you can flexibly rotate the accessories.
Buy on Amazon Price incl. tax, excl. shipping
Bestseller No. 10
Heavy Duty Adjustable Clevis Pin ,Fastener Tool Size 1/4 x 2inch Zinc Steel 8 Holes W/ Matching R- Clip (10)
Heavy Duty Adjustable Clevis Pin ,Fastener Tool Size 1/4 x 2inch Zinc Steel 8 Holes W/ Matching R- Clip (10)
  • 1.Multiple holes are designed on the product surface, Take Away The Frustration Of Finding The Exact Length With These Adjustable Clevis Pins Which Come In a Variaty of Sizes to Choose From

  • 2. All Our Fasteners Are Made of Top Quality Materials;

  • 3. Zinc Coated Steel Means They Are Sturdy And Zinc Helps The Adjustable Clevis Pins Last Longer In All Types Of Conditions;

  • 4 These Adjustable Clevis Pins Go Well Wth Our Cotter Pins or Hitch Pins (see photos for graphic chart - showing which Cotter or Hitch pin fits each Clevis Pin);

  • 5 Package Included： 10 sets x Adjustable Clevis Pin (Clip Hitch Pin X10 ,R-clip X10 )

$12.99 Amazon Prime
Buy on Amazon Price incl. tax, excl. shipping

Last update on 2024-06-15 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

BufferCopyFlipboardHacker NewsLinkedInMessengerMixPinterestPocketPrintRedditSMSTelegramTumblrVKWhatsAppLineXing

Leave a Comment

Share to...
BufferCopyFlipboardHacker NewsLineLinkedInMessengerMixPinterestPocketPrintRedditSMSTelegramTumblrVKWhatsAppXing