9901433 – Fresh Water Tank Support – 2019 Jayco Jay Flight TF Travel Trailers

“This site contains affiliate links for which OEMDTC may be compensated”

April 30, 2019 NHTSA CAMPAIGN NUMBER: 19V335000

Fresh Water Tank Supports may Fail

 

A detached water tank would be a road hazard, increasing the risk of crash.

 

NHTSA Campaign Number: 19V335

Manufacturer Jayco, Inc.

Components EQUIPMENT

Potential Number of Units Affected 86

 

Summary

Jayco, Inc. (Jayco) is recalling certain 2019 Jay Flight TF travel trailers, model 32RLOK. The supports for the fresh water tank may be too thin, resulting in the brackets breaking and the tanks detaching from the trailer.

 

Remedy

Jayco has notified owners, and dealers will install a threaded rod in the center of the water tank support apparatus to provide additional support, free of charge. The recall began May 9, 2019. Owners may contact Jayco customer service at 1-800-517-9137. Jayco’s number for this recall is 9901433.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 


Fresh Water Tank Support

Bulletin Type: RECALL Publication Date: May 2019
Bulletin #(s): 19V-335 US

2019-211 CN

Make: Jayco
Job Code: 9901433 Model: Jay Flight 320RLOK  “TF”
Flat Rate(s): RC024 Repair A – .8 hour

RC025 Repair B – 1.2 hour

Model Year: 2019

 

PARTS KIT REQUIRED

Incident: The support apparatus for the fresh water tanks require additional support 
Affected Units:  

2019 Jay Flight 32RLOK “TF”

K1TF0050-0106, 0108, 0110-0112, 0114, 0120, 0124, 0127, 0129, 0136 -0137, 0144,-0145 

 

Parts Kit: Parts Kit #:19V-335
Contents:

1  – Plastic, Lam 10” x 68” (underbelly material)

2  – Nut, hex flg 3/8-16 GR5

12 – Screw, Pan Qd #10 x ¾” TEK3 w/washer

1 – Rod, thrd 3/8-16 x 9” long

1 – Sleeve, spacer steel 6.875” length

Misc. Tools & Supplies: Screw gun with #2 square bit

Drill with 3/8” bit (12 inches long)

Deep well Socket – 9/16” with socket adapter

9/16” open end wrench

Socket – 3/4”

Utility Knife

Torque wrench (Ft/lbs.)

Parts Return Information: Not applicable

 

NOTE:  There are 2 sets of repair instructions.

Repair instruction (A) RC024 for trailers without enclosed underbelly.

Repair instruction (B) RC025 for trailers with an enclosed underbelly

 

REPAIR INSTRUCTIONS  A    (without enclosed underbelly ) .8hr

 

FIG 1A & 2A:

  • Use 9/16” socket and screw gun to remove the middle nut and bolt from the straps securing the water tanks.
  • Middle bolt location is circled in Fig 2A.

FIG 3A:

  • Use the drill with the foot long 3/8” drill bit, and insert it into the middle bolt location on the tank strap.
  • A 3/8” diameter hole needs to be drilled up into the bottom flange of the C-channel above the water tanks.
  • The C-channel runs directly between the two water tanks.

FIG 4A:

  • Drill bit shown between water tanks, and ready to drill hole in the bottom flange of the C-channel above the tanks.

FIG 5A:

  • Install the spacer tube between the tank strap and the bottom of the C-channel just drilled.

FIG 6A

  • Insert the 9” long threaded rod into the spacer tube.
  • Approximately ½” of the threaded rod should extend above the C-channel.

FIG 7A:

  • Reach up between the tanks and install one of the 3/8” nuts from the kit on the end of the threaded rod on top of the C-channel.
  • Make sure at least 2 or 3 threads of the rod extend beyond the top of the nut on top of the C-channel.

FIG 8A:

  • Install the other 3/8” nut from the kit on the bottom end of the threaded rod at the tank straps.
  • At least 2-3 threads of the rod should extend beyond the top of the nut.
  • Tighten the bottom nut with the ratchet and a 9/16” socket, and the top nut with a 9/16” open end wrench above the tanks.
  • Finish with a torque wrench and the 9/16” socket (on the bottom nut) and TORQUE THE FLANGE NUT TO 22 FT/LBS.

 

REPAIR INSTRUCTIONS  B (with enclosed underbelly) 1.2 hr

  • Remove both rear stabilizer jacks.
  • Remove two bolts on outside of the frame rail. (9/16” socket, socket adapter & screw gun)
  • Remove 2 lag screws on the inside of the frame rail. (9/16” socket, socket adapter & screw gun) FIG 2:
  • Remove the accessory receiver bar from the rear of the trailer (if equipped).
  • NOTE: in the photos that follow the receiver bar was left in place, but it is much easier if it is removed.
  • Use the 3/4” socket to remove the 2 bolts on each end of the accessory receiver bar.
  • Save the hardware for re-installation.

FIG 3:

  • Hard plastic underbelly cover must come down to access water tanks.
  • Remove enough underbelly screws to allow 5 feet of it to be pulled down from rear of trailer.

FIG 4 & 5:

  • There are screws holding the main underbelly material up above the rear bumper, you must cut the underbelly material below these screws in the area shown by the dashed line in Fig 4.
  • Cut across the rear of the underbelly material above and behind the rear bumper with a utility knife (arrow) (Fig 5).
  • Pull down the main underbelly from the end of the frame at the rear, and pull toward the front of trailer approximately 5 feet.
  • There is expanding foam around the stabilizer jacks and other areas that must be chipped away so the underbelly can be pulled down from frame rails.

FIG 6 & 7:

  • Underbelly pulled down exposing the water tanks.
  • Use 9/16” socket and screw gun to remove the middle nut and bolt from the straps securing the water tanks.
  • Middle bolt location is circled in Fig 7.

FIG 8:

  • Use the drill with the foot long 3/8” drill bit, and insert it into the middle bolt location on the tank strap.
  • A 3/8” diameter hole needs to be drilled into the bottom flange of the C-channel above the water tanks.
  • The C-channel runs directly between the two water tanks.

FIG 9:

  • Drill bit shown between water tanks, and ready to drill hole in the bottom flange of the C-channel above the tanks.

FIG 10:

  • Install the spacer tube between the tank strap and the bottom of the C-channel just drilled.

FIG 11:

  • Insert the 9” long threaded rod into the spacer tube.
  • Approximately ½” of the threaded rod should extend above the C-channel.

FIG 12:

  • Reach up between the tanks and install one of the 3/8” nuts from the kit on the end of the threaded rod on top of the C-channel.
  • Make sure at least 2 or 3 threads of the rod extend beyond the top of the nut on top of the C-channel.

FIG 13:

  • Install the other 3/8” nut from the kit on the bottom end of the threaded rod at the tank straps.
  • At least 2-3 threads of the rod should extend beyond the top of the nut.
  • Tighten the bottom nut with the ratchet and a 9/16” socket, and the top nut with a 9/16” open end wrench above the tanks.
  • Finish with a torque wrench and the 9/16” socket (on the bottom nut) and TORQUE THE FLANGE NUT TO 22 FT/LBS.

FIG 14:

  • Insert the 10” x 68” piece of underbelly material under the tanks, resting on the frame rails.
  • This underbelly piece will be bent up and secured to the piece of angle being pointed to in Fig 14 (arrow).

FIG 15:

  • 10” x 68” underbelly piece will need to be trimmed around the bumper support tube (on each end of the bumper) (arrow).

FIG 16:

  • Secure the 10” underbelly piece to the angle steel (Fig 14) using ¾” screws and washers from the kit.
  • It will take approximately 10 screws to secure the underbelly piece to the angle.

FIG 17:

  • NOTE: if there was any insulation batting between the tanks and the underbelly reinstall that now before securing the underbelly in place.
  • Reinstall the main underbelly up between the frame rails Underbelly needs to be pulled tight at the rear of the trailer.
  • Reinstall the underbelly screws.

FIG 18:

  • At the rear of the trailer: pull the main underbelly underneath the 10” piece installed previously.

FIG 19:

  • The main underbelly will need to be cut off with the utility knife and secured to a steel angle where the 10” piece (installed previously) bends upward. (See Fig 20 & 21)

FIG 20:

  • The main underbelly piece will be cut off in the area of the dashed line, which is right where the 10” piece bends upward. DO NOT CUT THE 10” PIECE THAT WAS INSTALLED AT FIG 14.

FIG 21:

  • Secure the main underbelly piece to a steel angle which is covered by the 10” underbelly piece.
  • Use ¾” screws with washers from the kit (shown circled in the photo).
  • It will take approximately 6 screws to secure the main underbelly piece.

FIG 22:

  • Apply expanding foam back in areas where it was chipped away previously.
  • Also apply expanding foam at each corner of the frame rail where the underbelly was notched (large arrow).

FIG 23:

  • Reinstall the stabilizer jacks under the trailer.
  • Install the lag screws on the inside rail of the frame first, but don’t tighten them completely.
  • This will allow some play to install the bolts on the outside rail of the frame.
  • Install the bolts on the outside rail of the frame, tighten those wrench tight (no torque spec).
  • After tightening the two bolts, the lag screws can be fully tightened (wrench tight), again no torque spec.

 

Reinstall the accessory receiver bar (if equipped).

Replace the 4 bolts and nuts that were removed previously.

Hardware can be re-used for this installation.

Use the torque wrench and ¾” socket and torque the nuts on the accessory receiver bar to 85 ft. /lbs.

 


IMPORTANT SAFETY RECALL

This Notice Applies to Your Recreational Vehicle «vin»

 

Dear Valued Customer:

This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.

Jayco has decided that a defect which relates to motor vehicle safety exits in certain Model Year 2019 Jay Flight, 32RLOK “TF” travel trailers 

Reason for this recall Under certain conditions, the brackets that make up the support apparatus for the fresh water tanks, may fail and allow the tanks to fall, which can create a road hazard and increase the risk of a crash.
Recall Remedy An authorized Jayco Dealer will.  The Recall Remedy is free of charge and will take approximately 1 hour to complete.
What we need you to do Please contact a Jayco Authorized Dealer as soon as possible to schedule an appointment to have this remedy completed.

 

If you had this repair completed prior to receipt of this recall notice, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall.

If you take your recreational vehicle to your dealer on the agreed service date and the dealer does not remedy this condition on that date or within three (3) days, please contact our Customer Service Department at 800-283-8267.  If after contacting your dealer and Customer Service you are not able to have the safety defect remedied without charge and/or within a reasonable time, you may wish to submit a written complaint to the Administrator, national Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590; or call the toll-free Vehicle Safety Hotline at 1-888-3274236 (TTY: 1-800-424-9153): or go to https://www.safercar.gov. Federal regulations require that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.

 

We certainly regret this inconvenience; however, your safety is our most important priority.

 

Sincerely,

Jayco Towables


Safety Recall: Jayco 19V-335  2019-211
May 2019

 

IMPORTANT SAFETY RECALL  

 

Dear Valued Dealer:

This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.

Jayco has decided that a defect which relates to motor vehicle safety exits in certain Model Year 2019 Jay Flight, 32RLOK “TF” travel trailers.

Reason for this recall Under certain conditions, the brackets that make up the support apparatus for the fresh water tanks, may fail and allow the tanks to fall, which can create a road hazard and increase the risk of a crash.
Recall Remedy Install additional support to the center bracket of the support apparatus.
All pertinent information regarding this recall is available under the Service and Parts Tab of our Website.  If you need further assistance, please Contact Customer Service at 800-283-8267.
What we need you to do Our records show the following unit is affected by this recall and is currently part of the inventory at your Dealership.  The Recall Remedy must be completed on this unit prior to customer delivery.

 

VIN

 

Federal law requires that all units in your inventory be repaired prior to delivery to a customer. If you have sold a unit recently that you have received a stock recall notice on, please contact the owner immediately to advise of the recall. In addition, please register the unit by submitting the Warranty Registration. 

 

We certainly regret this inconvenience; however, our Customers’ safety is our most important priority.

 

Sincerely,

Jayco Towables


1 Affected Product

Vehicle

MAKE MODEL YEAR
JAYCO JAY FLIGHT 2019

 


11 Associated Documents

Recall 573 Report – Amendment 2

RCLRPT-19V335-1827.PDF 212.959KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [207.97 KB]

 


Remedy Instructions and TSB

RCRIT-19V335-6677.pdf 1138.591KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.09 MB]

 


Recall Acknowledgement

RCAK-19V335-4325.pdf 245.75KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [239.99 KB]

 


ISSUED Owner Notification Letter(Part 577)

RCONL-19V335-4392.pdf 158.758KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [155.04 KB]

 


Recall 573 Report – Amendment 1

RCLRPT-19V335-5882.PDF 212.959KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [207.97 KB]

 


Miscellaneous Document-19V-335 2019-211 Order Form

RMISC-19V335-3936.pdf 138.911KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [135.66 KB]

 


Manufacturer Notices(to Dealers,etc)-19V-335 Dlr. Ltr. docm

RCMN-19V335-1707.pdf 183.765KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [179.46 KB]

 


Defect Notice 573 Report

RCLRPT-19V335-8959.PDF 212.957KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [207.97 KB]

 


Recall Quarterly Report #1, 2019-2

RCLQRT-19V335-5951.PDF 211.126KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.18 KB]

 


Recall Quarterly Report #3, 2019-4

RCLQRT-19V335-4646.PDF 211.307KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.35 KB]

 


Recall Quarterly Report #2, 2019-3

RCLQRT-19V335-1023.PDF 211.222KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.27 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V335&docType=RCL

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
Bestseller No. 1
16 Gallon RV Fresh/Gray Water Tank 24" x 15" x 10" BPA Free (16 Gallon)
  • This 16 gallon water tank measures 24" x 15" x 10" (not including fittings)
  • These rotational molded fresh water tanks are made from a high quality durable polyethylene material.
  • One piece seamless construction - No Seams to burst
  • All tanks come with (1) 1.25" water fill inlet and (3) 3/8" NPT connections. Non-Pressurized Tank - The tank must be vented
  • Stain, corrosion and rust resistant features make them ideal for replacement or OEM installation on RVs, horse trailers or marine products.
Bestseller No. 2
RecPro Fresh and Gray Water Holding Tank | Combo Pack | Concession/Food Truck Holding Tank (10 & 16 Gallon)
  • All tanks have been pressure tested
  • Made in America
  • Please be sure to clean tanks before use
Bestseller No. 3
Class A Customs | One (1) RV Fresh and Gray Water 30 Gallon Tank | T-3000
  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 34.5” Longest Length (not including fittings) x 12” x 17.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.: (TWO) 1.5" Balloon Style Threaded Female NPT Standard - fitting will be closed, to use remove inner membrane with razor knife (TWO) .5" Threaded Female NPT Standard - open fitting, unsealed
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 4
Class A Customs | T-7500 | 75 Gallon Fresh Water Holding Tank
  • 75 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 50.5” Longest Length (not including fittings) x 17.5” x 19.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 5
Class A Customs | T-2000 | One (1) RV Fresh Water 20 Gallon Tank, Grey Water
  • 20 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 6
Class A Customs | 10 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-1000-BPK-PUMP
  • 10 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 19” Longest Length (not including fittings) x 9” x 14” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose
  • classAcustoms 12 VOLT Fresh Water Pump MODEL # 12V3 - FRESH WATER USE ONLY - OPEN FLOW 11.6LPM / 3.0GPM AMPS 4.0A MAX AMPS 8.0A SHUT OFF PRESSURE 45PSI/3.1 Bar ON-DEMAND PUMP only turns on when senses pressure changes in line 12 VOLT POWER ONLY 110/115/220 volt will damage the unit - READ INSTRUCTION BOOKLER BEFORE INSTALLATION
Bestseller No. 7
Bestseller No. 8
Ameri-Kart WT-1468 50 Gallon RV Fresh Water Tank for Drinking and Potable Water, for Campers, Trailers, and RVs, 57-Inch x 31-Inch x 9-Inch
  • 50 GALLON TANK - Ameri-Kart Fresh water tanks are MADE IN THE USA - Fresh Water Tanks are for CLEAN DRINKING WATER USE - Perfect for motorhomes, trailers, tiny houses, RVs and campers
  • EASY TO INSTALL - fresh water tanks are a critical compenent to all recreational vehicles - Built-in fittings include: (TWO) 0.5" Threaded female NPT standard - fittings are plugged, to use remove threaded plugs; (ONE) 1.25" Outer Diameter Boss Fitting (smooth pipe) for use with hose and clamps (not included); (ONE) 1.5" Threaded Female NPT standard. Pre-installed high-medium-low level sensor probes for tank fullness indicator
  • DURABLE & RELIABLE - OEM quality tank made from weather resistant and impact-resistant plastics. RV Fresh Water Tank design prevents leaks and ensures long service life. Built to standards specified by IAPMO (International Association of Plumbing and Mechanical Officials). All water tanks are QAI Laboraties certified to meet industry-required standards
  • NOT INCLUDED - hardware, mounting hardware, gate valves, piping, hoses, fittings; DO NOT PRESSURIZE TANK. DO NOT HANG TANK BY STRAPS OR PLACE WEIGHT ON TANK
  • USA MADE - Proudly manufactured by Ameri-Kart in Elkhart, Indiana - the RV Capital of the World
Bestseller No. 9
Class A Customs | T-1000 | One (1) RV Fresh Water 10 Gallon Tank, Grey Water
  • 10 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage
  • WATER TANK MEASUREMENTS: 19” Longest Length (not including fittings) x 9” x 14” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement)
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process.
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhart, Indiana. Tanks are made in a warehouse clean each tank prior to use to remove any debris, scuffs or marking from the manufacturing process.
Bestseller No. 10
Class A Customs | RV Fresh and Gray Water Tank | Combo Pack (10 Gallon & 13 Gallon) | RV Water Holding Tanks
  • Combo Pack of RV Fresh & Gray Water Tanks, 10 Gallon & 13 Gallon
  • NSF Certified MATERIALS used for manufacturing process -- ALL PARTS of tank made with NSF International NSF/ANSI Std 61 approved Medium Density Polyethylene (MDPE) Resin with UV-8 stabilization -- The tank and fittings are both made out of this material.
  • The 10 and 13 gallon tanks each have two 1/2" female NPT fittings (fitting will be closed, to use remove inner membrane with razor knife) and two 1 1/2" female NPT fittings (fitting is not closed, this fitting is completely open)
  • 10 Gallon Tank measurements - 18 3/4" x 13 3/4" x 8 3/4" (+/- .25")
  • 13 Gallon Tank measurements - 21" x 16" x 9" (+/- .25")

Last update on 2024-03-16 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...