| “This site contains affiliate links for which OEMDTC may be compensated” |
January 9, 2018
Transfer Switch Electrical Connections May Loosen
The excessive heat can increase the risk of a fire.
NHTSA Campaign Number: 18V056
Manufacturer E-One Incorporated
Components ELECTRICAL SYSTEM
Potential Number of Units Affected 196
Summary
E-One Incorporated (E-One) is recalling certain 2005-2010 E-One Typhoon, Cyclone II, X-036, Cyclone III, SPGL, SPBE, FLM2, F550, I440, and I740 emergency vehicles, equipped with an IOTA 50 Amp transfer switch. Electrical connections at the transfer switch may loosen and cause excessive heat.
Remedy
E-One will notify owners, and dealers will replace the IOTA transfer switch with a Powermax switch, free of charge. The recall began on February 19, 2018. Owners may contact E-One customer service at 1-352-861-3612.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
IMPORTANT SAFETY RECALL: 18V-056–
NHTSA Recall LETTER
Mar 02, 2018
Dear E-ONE Chassis Owner:
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.
Why is a recall being conducted?
E-ONE has decided that a defect which relates to motor vehicle safety exists in certain models of the following emergency vehicles manufactured Jan. 2005 – Dec. 2010, equipped with IOTA brand 50 Amp transfer switches, IOTA manufacturer’s model number ITS-50R:
E-ONE Typhoon, E-ONE Cyclone 2, E-ONE X036, E-ONE Cyclone 3, E-ONE SPGL, E-ONE SPBE, E-ONE FLM2, E-ONE F550, E-ONE I440, E-ONE I740
Affected vehicles are equipped with an IOTA 50 Amp transfer switch, which is used to switch power between on-vehicle generator and shoreline power. Under certain heavy duty cycles, these switches may experience loosening of the lugs on the buss bar.
Under high electrical loads, loose electrical connections at the lugs can cause high heat which could damage the enclosure of the switch, and could lead to a fire.
What are we doing about the problem?
E-ONE recommends replacement of the IOTA switch with a new switch made by POWERMAX. Vehicles subject to this recall are to be inspected and repaired by an E-ONE certified dealer or technician. E-ONE will compensate the dealer or owner for inspecting and replacing the IOTA transfer switch (IOTA model number ITS-50R), with a POWERMAX transfer switch (E-ONE part
#538550) supplied free of charge if it has not already been replaced during normal maintenance. Replacement of each transfer switch should take approximately 2 hours.
If you believe you have a valid warranty claim that extends beyond the IOTA brand transfer switch replacement, please contact E-ONE Customer Service at 1-352-861-3612 or write EONE, 1601 SW 37th Ave, Ocala, FL, 34474.
What should you do?
If you receive this notification, please contact your E-ONE Dealer or E-ONE at 1-800-627-5050 to schedule an appointment to have the inspection and replacement of the IOTA brand 50 Amp transfer switch performed. This Recall is expected to start on or before March 2, 2018.
INCLUDED WITH THIS LETTER IS AN OWNER RESPONSE CARD THAT MUST BE FILLED OUT AND RETURNED TO E-ONE IN ORDER TO BE REIMBURSED. Please have your Truck
VIN available. After your repair has been completed, please fill in the appropriate information on the enclosed Owner Response Postcard, sign it, and mail it to:
E-ONE, 1601 SW 37th Ave, Ocala, FL, 34474.
If you prefer to contact E-ONE directly, feel free to contact our Customer Service at 1-352-8613612. Please have your Truck VIN available.
What if you no longer own this vehicle?
If you are not the current owner of the vehicle, please indicate this on the Owner Response Postcard and return the card to us.
Federal law requires that any lessor who receives a notification of a safety related defect or noncompliance pertaining to any leased motor vehicle shall send the notice to the lessee within 10 days. If you are no longer the owner of this vehicle, please provide us with any contact information so we may contact the new owner.
If you have already paid to have your vehicle repaired for this condition, you may be eligible for reimbursement of the charges you paid for the repair or replacement of components. If after having attempted to take advantage of this recall you believe you have not been able to have your vehicle remedied without charge and within a reasonable amount of time, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., S.E., Washington, D.C., 20590; or call the toll-free Vehicle Safety Hotline at 1-888327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov.
We apologize for any inconvenience this safety recall may cause, but your safety is our first concern.
Sincerely,
E-ONE, Inc.
60 Affected Products
Vehicles
| MAKE | MODEL | YEAR |
| E-ONE | CYCLONE II | 2005-2010 |
| E-ONE | CYCLONE III | 2005-2010 |
| E-ONE | F550 | 2005-2010 |
| E-ONE | FLM2 | 2005-2010 |
| E-ONE | I440 | 2005-2010 |
| E-ONE | I740 | 2005-2010 |
| E-ONE | SPBE | 2005-2010 |
| E-ONE | SPGL | 2005-2010 |
| E-ONE | TYPHOON | 2005-2010 |
| E-ONE | X-036 | 2005-2010 |
7 Associated Documents
Recall Quarterly Report #1, 2018-1
RCLQRT-18V056-9525.PDF 214.506KB
Loading...
Reload document 
Open in new tab
Recall 573 Report-Amendment 1
RCLRPT-18V056-2409.PDF 218.877KB
Loading...
Owner Notification Letter(Part 577)
RCONL-18V056-6513.pdf 352.933KB
Loading...
Defect Notice 573 Report
RCLRPT-18V056-9746.PDF 218.93KB
Loading...
Recall Acknowledgement
Loading...
Recall Quarterly Report #3, 2018-3
RCLQRT-18V056-0653.PDF 211.318KB
Loading...
Recall Quarterly Report #4, 2018-4
RCLQRT-18V056-2156.PDF 211.421KB
Loading...
Latest Recalls Documents
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=18V056&docType=RCL
| “This site contains affiliate links for which OEMDTC may be compensated” |
HIGH-QUALITY PRODUCT The PMTS automatic transfer switches are designed for use in RV’s with 30 AC service. When plugged into the shore power it will automatically provide AC power to all AC appliances. To operate your appliances from an onboard generator or alternative Power source simply start them and the PMTS-30 will automatically transfer the electrical power to AC appliances. They also feature a time delay of 20-30 seconds to allows the generator voltage to stabilize
BEST FEATURES This automatic transfer switch features automatic transfer between 2 – 110 Vac inputs to a single 110 Vac output. It is also an ideal use for RVs, off-grid, and backup power solutions. This comes with a 30A size with 12 Volt DC Relay. And of course, a two-year warranty.
SAFE TO USE This automatic transfer switch will not boil the battery. It has an Intelligent way to charge and maintain your RV battery and very easy to install so it’s a free hassle to use.
NO NEED TO REWIRE With no need to re-wire, installation is only 10 minutes! It has an automatic three-stage converter that handles every charging need for the RV while extending the battery’s life. Well-maintained batteries should never need more than two-stage (normal and trickle) charging.
CONSTANT AND STABLE Power supply mode provides stable power to maintain system voltage for use in a wide variety of applications. Provides a constant clean power supply for using scan tools and reprogramming of ECMs without discharging the battery
- Safe and Automatic Transfer Switch - Furrion’s 50amp Automatic Transfer Switch has a built-in safe switch interlock system and is used to automatically switch between two separate 125 /250 volt AC power sources. These power sources can be from a Generator, shore power cord or inverter
- Avoid Over-voltage - Provides an added feature of a mechanical interlock between contractors to ensure both contactors cannot be closed in parallel, preventing overvoltage on the output line.Casing Material: UL 94 Fireproof Plastic
- Time Delay - Once AC power from the Generator is sensed by the transfer switch at Input 2 terminals, it will start a timer and automatically switch over to generator power supply after a 20-30 sec delay which ensures the generator has sufficient time to run up to speed before electrical load is applied.
- Durable & Reliable: Designed with Furrion's proprietary VibrationSmart and ClimateSmart technologies, this ATS is built to withstand constant vibrations & extreme temperatures. Solid brass terminals are used to increase conductivity and reduce heat and are Nickel plated for corrosion resistance.
- Highest Safety Standards - The Automatic Transfer Switch comes in a UL94 Flame retarded enclosure and is certified to UL Standards UL1008.
- Nirakoka RV Automatic Transfer Switch has been pre-wired to automatically change the primary source of AC current from shore power to generator or inverter power when activated.
- WIDE APPLICATION — Applied to RVs, speedboats, and various high-power equipment that requires emergency power supply.
- AUTOMATICALLY SWITCH — This Automatic Transfer Switch 50 AMP can be used to automatically switch between inverter power and a generator. It switches to inverter power when the generator stops running. In the event of a inverter power outage, the generator will start automatically. The green L.E.D is lit when generator power is present.
- DOUBLE PROTECTION — Double protection of built-in mechanical interlocks and control circuits prevents two separate 120/240 volt AC power sources from entering the AC distribution board at the same time and causing a short circuit.
- TIME DELAY CIRCUIT — Once AC power from the Generator is sensed by this RV Automatic Transfer Switch, it will start a timer and automatically switch over to generator power supply after a 20-45 sec delay which ensures the generator has sufficient time to run up to speed before electrical load is applied.
- Rugged, heavy duty, screw type wiring terminals ready to wire to contactor base.Fit Type: Universal Fit
- Time delay circuit board ensures generator voltage is at a stable level before transfer occurs. Automatically senses generator power and prevents two power sources from entering the AC Distribution Panel at the same time
- Easy-to-remove protective cover with wiring schematic inside
- 240 VAC, 50 Amps
- One-year limited warranty
- 50 amp Automatic transfer switch can be used to automatically switch between inverter power and a generator. rv transfer switch automatically senses generator power and prevents two power sources from entering the AC distribution panel at the same time.
- 50 amp, 120v transfer switch/ 240 AVC is your good choicce. If you are using public power and it goes out, when the generator is turned on it will automatically switch the power to it.The green light is in an active state
- This RV automatic transfer switch has a 30 second selectable delay with quick-connect terminals for easy installation.Wide application-RV, SPEEDBOAT,OUTDOOR. * Function：120/240 VAC, 50 Amp
- Automatic transfer switch transfer 50 amp has been pre-wired to automatically change the primary source of AC current from shore power to generator or inverter power when activated
- Reliable Service. If you have any question about this generator transfer switches, please contact us. 12 month warranty of this automatic transfer switch, buy with confidence.
- NEW GENERATION: Our generator's automatic transfer switch is configured to prioritize generator power. It automatically switches to utility power when the generator stops running. When the generator restarts, the green light indicates that the generator power is active. Additionally, the switch continuously monitors the utility power status. In the event of a utility power outage, the generator will start automatically, requiring no extra wiring on your part, providing exceptional convenience
- DELAY CIRCUIT PROTECTION FUNCTION: When switching to the generator power supply, the built-in MCU precise control circuit is connected with a delay of 20s, so that the generator voltage is maintained at a stable level and then transmitted. Double protection of mechanical interlocks and control circuits prevents two power sources from entering the AC distribution board at the same time and causing a short circuit
- DURABLE ENCLOSURE: The coating process used on the surface of our products can be waterproof, rust-proof and anti-corrosion.The waterproof level can reach ip65, which can effectively prolong the service life of the product so that it's very durable
- EASY TO INSTALL: Our products have simple installation steps, easy-to-remove protective cover with wiring diagram inside,and the internal copper wiring is more concise and durable
- WIDE APPLICATION: 120/240 VAC, 50 Amps. It can be applied to RVs, speedboats, and various high-power equipment that requires emergency power supply
- 🚘Double Protection — Double protection of built-in mechanical interlocks and control circuits prevents two separate 120/240 volt AC power sources from entering the AC distribution board at the same time and causing a short circuit.
- 🚘This automatic transfer switch has a 30 second selectable delay with quick-connect terminals for easy installation.
- 🚘This transfer switch has been pre-wired to automatically change the primary source of AC current from shore power to generator or inverter power when activated
- 🚘Easy-to-remove protective cover with wiring schematic inside
- 🚘1 year warranty is provided. If you have any problem , please feel free to contact us
- HCDC HD060 Automatic transfer switch, an easy to mount 15Amp inline transfer relay provides switching between AC INPUT 2 (Utility or Shore Power) and AC INPUT 1 (Inverter or Generator) AC source. When AC INPUT 2 is powered, the load power will be switched to AC INPUT 2. When AC INPUT 2 is powered off, the load power will be switched to AC INPUT 1.
- Operating voltage AC 90 to 135V 50/60Hz. Maximum current 15 Amp. Transfer time less than 30mS (0.03 second). For most smart devices or computers, the switching action of 30mS time will not affect their normal operation.
- Internal four high power SPST relays switch design, effectively avoid the problem of DPDT relay high inductive load arcing. Live and Neutral wire are switched at the same time. The Ground wires of the two inputs and output are connected together internally and will not follow the switch on and off.
- IP68 Waterproof high level enclosure, suitable for indoor or outdoor use. Flame retardant rating V1. Case material: PC (Polycarbonate). Seal material: Silicone rubber. External screw: 304 stainless steel.
- AC INPUT 1 cable: Length 19 inch (0.5 meter), US standard NEMA 5-15P 3 prong plug. AC INPUT 2 and AC OUTPUT cables: Length 19 inch (0.5 meter), 14AWG (2.08 square millimeter) x 3 cores.
- ⚡Application automatic transfer switch device:Line Voltage: AC110V;Line Current: 6A-63A;Operating Frequency: 50HZ/60HZ; insulation Voltage: AC110V
- ⚡Conversion Time: 2S or so;Conversion Mode: self cast; Display Function: Indicator light display;Installation Dimension: 128mm*122mm hole: M6
- ⚡When one power goes wrong (only test normal Phase A voltage and reserve Phase A voltage, only test loss voltage or loss phase),it will automatic connect one or several load circuits from one power to the other power automatically, to ensure normal power supply of load circuits.
- ⚡Complete protection function:This switch support variety protection function, including short circuit, overload, lack of phase, under voltage protection.
- ⚡Easy installation:Reasonable structure, small size, equipped with protective cover, power supply is easy to install and reliable.
Last update on 2024-06-13 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.