“This site contains affiliate links for which OEMDTC may be compensated” |
February 26, 2024 NHTSA CAMPAIGN NUMBER: 24V150000
Battery Disconnect Switch May Overheat
The incorrect battery disconnect switch can overheat, increasing the risk of a fire.
NHTSA Campaign Number: 24V150
Manufacturer Pleasant Valley Teardrop Trailers LLC
Components ELECTRICAL SYSTEM
Potential Number of Units Affected 163
Summary
Pleasant Valley Teardrop Trailers LLC (Pleasant Valley) is recalling certain 2023-2024 nuCamp TAB 400, Cirrus 620, and 820 trailers with the Lithium Upgrade. The incorrect battery disconnect switch may have been installed.
Remedy
Dealers will replace the battery disconnect switch, free of charge. Owner notification letters were mailed March 05, 2024. Owners may contact Pleasant Valley customer service at 1-330-852-4811- ext. 327.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
IMPORTANT SAFTEY RECALL
March 4, 2024
Re: NHTSA Safety Recall: 24V150; nuCamp Safety Recall – Battery Disconnect Switch This notice applies to your vehicle [VIN]
Dear Owner,
This notice is being sent in accordance with the requirements of the National Traffic and Motor Vehicles Safety Act.
Pleasant Valley Teardrop Trailers LLC has decided that a defect, which relates to motor vehicle safety; exist in certain 2023-2024 nuCamp Tab400, Circus 820 & 620 trailers equipped with lithium upgrade units there is a 250AMP Battery Disconnect Switch installed, which is not sufficient to carry a consistent draw above the 250AMP rating. If there is a consistent draw above the 250AMP rating, then it could cause wires to melt near the Batter Disconnect Switch, increasing the risk of a fire. Pleasant Valley Teardrop Trailers/nuCamp will be replacing the 250AMP battery disconnect switch with a 400AMP battery disconnect switch.
Pleasant Valley Teardrop Trailers (LLC) / nuCamp has identified the VIN numbers impacted by this safety recall.
If your VIN number is included in the recall, please contact your dealer, and schedule an appointment for your free repair as soon as possible. To find your nearest dealer, visit nucamprv.com. You may also contact the nuCamp Service Center at 330-852-4811 ext 925 to schedule an appointment. The repair will take approximately one hour and be completed at no charge to you.
If you have questions or concerns about this recall please contact Pleasant Valley Teardrop Trailers LLC, Warranty Department at 330-852-4811 or send an email to warranty@nucamprv.com.
If your dealer fails or is unable to remedy this defect without charge, or within a reasonable amount of time, you may submit a written complaint to: Administrator, National Highway Traffic Safety Administration, 1200 New Jersey AVE, SE, Washington DC 20590.
You may also call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to http://www.safercar.gov.
If you are a lessor Federal law requires that you forward a copy of this safety recall notice to the lessee within 10 days.
You may be eligible to receive reimbursement for the cost of repairs made prior to receiving this notice. You may submit your receipts to warranty@nucamprv.com or by mail to
nuCamp Warranty
661 Belden Parkway NE
Sugarcreek, Ohio 44681
If you no longer own the vehicle, please contact our Warranty Department at 330-852-4811 or by email at warranty@nucamprv.com
We apologize for any inconvenience and thank you for your attention to this safety matter.
Sincerely,
Aaron Hawkins
Parts & Warranty Manager
Chronology :
Our E&I department was administering a test on our lithium battery system and noticed the 250AMP battery disconnect would become warm if there were multiple components running off the lithium system at the same time. They determined that if the system was drawing 275AMP consistently then it would cause the battery disconnect to overheat and the possibility of wires melting. – The E&I team felt is was necessary to upgrade the battery disconnect to a 400AMP battery disconnect switch which would allow the system to function without any concerns. – The E&I team has put together instructions to complete the exchange of the 250AMP battery disconnect to the 400AMP disconnect.
6 Affected Products
Equipments
BRAND | PART NO. | PRODUCTION DATES |
NUCAMP | CIRRUS 620 TRUCK CAMPER | |
NUCAMP | CIRRUS 620 TRUCK CAMPER | |
NUCAMP | CIRRUS 820 TRUCK CAMPER | |
NUCAMP | CIRRUS 820 TRUCK CAMPER |
Vehicle
MAKE | MODEL | YEAR |
NUCAMP | TAB 400 | 2023-2024 |
4 Associated Documents
Defect Notice 573 Report
RCLRPT-24V150-9135.PDF 213.816KB
Recall Acknowledgement
RCAK-24V150-2628.pdf 646.433KB
Owner Notification Letter(Part 577)
RCONL-24V150-2139.pdf 83.298KB
Recall 573 Report – 03/18/2024
RCLRPT-24V150-1794.PDF 213.8KB
Latest Recalls Documents
For the Latest and Most recent Recall Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=24V150&docType=RCL
- Rotary Switch
- Panel Mount
- 125 amp 12V
- Aluminum On / Off Panel
- Fit type: Vehicle Specific
- Convenience: direct fit and no modifications, hook up to TOP post battery negative directly, do not need additional battery cables or lugs, isolate and secure the electrical system easily.
- Operation: used for DC 12 - 48 V systems, ON/OFF 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.
- Heavy Duty: ABS plastic housing, durable made for safety use. Extended the top post battery negative to original size: standard top post negative (17 mm cone/tapering negative (-)), installation space should be checked.
- Compatible: used for standard top post battery (19 mm cone/tapering positive & 17 mm cone/tapering negative). Can stand alone or be locked together with other switch.
- Purpose: eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely, widely used for car, vehicle, Rv and boat.
- Ideal for car, truck, boat or RV battery
- Convenience: knob type, easy to install & simple to use. Loose / twist of the knob, then power will cut.
- Heavy Duty: solid brass made, rust and corrosion resistant, durable made for safety use.
- Purpose: used for battery to isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.
- 【COMPATIABLE】This knife-blade battery disconnect switch is suitable for TOP POST TERMINAL, battery NEGATIVE post only. Maximum Current: 750A, Rated Current: 250A. 6v 12v 24v car truck, bus, RV, Boat, trailer battery
- 【TOP LEVEL & HEAVY DUTY 】This top post battery disconnect switch is made of brass material, corrosion resistance, conductive performance is good, durably made for safety use
- 【EASY TO INSTALL】This battery doctor knife switch for top post batteries can be adjusted into a vertical knife switch through the bottom of the screw, easy to install & simple to use. Switch the knife, then power will cut
- 【SAVE ELECTRYCITY】This knife blade master switch is used for the battery to isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, stop unwanted battery drain and prevent theft or unauthorized use. Widely used for car, truck, boat or RV battery, also other electrical equipment's battery
- BUY WITH CONFIDENCE: We are so confident you'll think we have the satisfied battery disconnect switch on the market. If you have any problem about our product, please feel free to give us a message and we will do anything for you to make the thing right. We go out of our way to make sure every customer is happy and satisfied with our product and service.
- Ultimate Protection: The remote battery disconnect switch easily solves the problem of battery drain but also protects the circuit, No matter how long your car is parked, The battery always has a full charge. The battery is via the remote switch, which also reduces the risk of theft occurs.
- Premium Quality: Remote battery kill switch Instantaneous current of up to 450A rated current of up to 250A. Our remote battery kill switch is made with high-quality materials and pure copper wire, modules have larger rivers for better reception performance and can extend car battery life by 3 - 4 times.
- Effortless Installation: Our upgraded remote battery kill switch for cars is designed to directly disconnect the negative switch, fix the battery clip to the negative pole of the battery, and connect the red wire to the positive pole of the battery, our upgraded version reduces a black power cord, making installation simpler than other products.
- Versatile Use: Our 12V remote kill switch for cars is suitable for cars, trucks, RVs, travel trailers, campers, motorcycles, and any other engine application with 12-volt batteries. Please note that disconnecting the positive terminal may damage the battery and vehicle circuit.
- Reliable Quality: If it cannot be used normally after installation, please check whether the circuit is installed normally or send a message to contact us, quality after-sales service is provided to go to meet any of your needs. If you have any questions you can email us and we will get back to you within 24 hours.
- HIGH CURRENT & WATERPROOF - 12V-36V, 500A rated current, 5000A instantaneous current, replacement part number: 20247, 10MM threaded studs with nuts, polarity negative, metal material, watertightness processing.
- SIMPLE OPERATION - High Current Battery Cut Off Switch with Lock-Out Plate, turn the knob to turn it on or off. The heavy duty rotary handle is locked to the panel through a padlock hole to prevent accidental opening or closing, as well as tampering or unauthorized use.
- UNIVERSAL BATTERY DISCONNECT SWITCH - Which protects against electrical fires and theft when equipment is not in use and provides a reliable way to shutdown electrical power during maintenance and protect batteries from excessive battery drain. Disconnect the battery when you are not driving a Car / Boat / RV / Yachts / Vehicle / ATV / Trucks / Off-road / Tractors / Agricultural Equipment, etc. Keep you safe all the time.
- EASY TO INSTALL - Compared to the remote control switch, there is no need for programming or code, just connect the product with wire, the operation is very simple. For the specific connection mode, please refer to the wiring diagram in our product picture. If you have any questions, please contact us in any time.
- 100% SATISFACTORY SERVICE - This 500A High Current Battery Disconnect Switch come with a 1 year warranty. Whether before, during or after sale, we always respond positively to your questions. What we pursue is not only to provide quality products, but also to provide satisfactory service.
- Compatible: used for top post terminal, 15-17 mm cone / tapering battery NEGATIVE post only, DC 12V-24V system, 200A continuous and 600A momentary at DC 12V, on/off 2 position.
- Convenience: vertical knife blade type, easy to install & simple to use. Lift the knife, then power will cut.
- Heavy Duty: solid brass made, rust and corrosion resistant, durable made for safety use.
- Purpose: used for battery to isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.
- Used for Car, Vehicle, RV and Boat batteries which have a standard 15-17 mm cone top post terminal, also used for electrical equipment.
- Heavy Duty: ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits, equipped with 4 sets of bolts.
- Operation: On/Off 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.
- Compatible: used for DC 12 - 48V systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.Its purpose is to eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.
- Widely used for car, marine boat, RV, camper, travel trailer, truck, ATV, UTV, battery banks and other devices.
- Package include:1x On/Off battery switch,4 bolts incuded.
- 【Compatible】- The battery disconnect switch is used for top post terminal(0.59''- 0.67'' cone battery negative post only). Compatible the condition of 12V voltage, 125A rated current, heavy duty.
- 【High Quality】- Our solid brass 12v battery disconnect switch with stainless steel fasteners provide excellent oxidation resistance and corrosion resistance, no need to worry about its service life.
- 【Easy to Use】Knob type design to disconnect or connect battery, just follow the direction instructions on the switch, unscrewing or tightening the battery switch into an “on” or “off” position to control current.
- 【Protect Battery】This battery shut off switch is designed to cut-off power flowing to the battery, avoid unwanted battery consumption when not used for long periods of time, extend the life of battery.
- 【Widely Applications】- Suitable for Car, Marine,tractor, camper, boat, RV, truck batteries which have a standard 0.59''-0.67''(15-17 mm) cone top post terminal, also used for electrical equipment.
Last update on 2024-04-01 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
OMB Control No.: 2127-0004
Part 573 Safety Recall Report 24V-150
The information contained in this report was submitted pursuant to 49 CFR §573
Manufacturer Name : Submission Date :
Pleasant Valley Teardrop Trailers LLC FEB 26, 2024 NHTSA Recall No. : 24V-150 Manufacturer Recall No. : NR Manufacturer Information :
Manufacturer Name : Pleasant Valley Teardrop Trailers LLC Address : 661 Belden Parkway NE
PO Box 395 Sugarcreek OH 44681
Company phone : 8524811 Population :
Number of potentially involved : 163 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2023-2024 nuCamp TAB 400, Cirrus 820 & 620 Vehicle Type : TRAILERS Body Style : OTHER Power Train : NR
Descriptive Information : – These units were selected because they were designated as Lithium Upgrades models. – A 250AMP Battery Disconnect was used during production of the Lithium Upgrade models. A 400AMP Battery Disconnect should have been used during production – There are 163 units affected overall in 2023 & 2024 model years. 2023 Cirrus 820 – 23 2023 Cirrus 620 – 17 2023 TAB 400 – 95 2024 Cirrus 820 – 8 2024
Cirrus 620 – 2 2024 TAB 400 – 18
Production Dates : JUL 22, 2022 – DEC 12, 2023
VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect :
Description of the Defect : These Lithium Upgrade units were produced with a 250AMP Battery Disconnect Switch. These units should have had a 400AMP Battery Disconnect installed during production.
FMVSS 1 : NR FMVSS 2 : NR
Description of the Safety Risk : If the system would consistently draw over 275AMPS then it would cause the 250AMP Battery Disconnect to overheat and potentially cause wires to melt.
Description of the Cause : Production Install Error
Identification of Any Warning
that can Occur :
NR Part 573 Safety Recall Report 24V-150 Page 2 Involved Components : Component Name 1 : BEP Battery Disconnect Switch Component Description : Battery Disconnect Switch Component Part Number : 48-00-2928 701B Supplier Identification : Component Manufacturer
Name : Pleasant Valley Teardrop Trailers Address : 661 Belden Parkway
Sugarcreek 44681
Country : NR Chronology :
Our E&I department was administering a test on our lithium battery system and noticed the 250AMP battery disconnect would become warm if there were multiple components running off the lithium system at the same time. They determined that if the system was drawing 275AMP consistently then it would cause the battery disconnect to overheat and the possibility of wires melting. – The E&I team felt is was necessary to upgrade the battery disconnect to a 400AMP battery disconnect switch which would allow the system to function without any concerns. – The E&I team has put together instructions to complete the exchange of the 250AMP battery disconnect to the 400AMP disconnect. Description of Remedy :
Description of Remedy Program : Our production team installed a 250AMP battery disconnect switch
incorrectly on the lithium upgrade units. The lithium upgrade units should have a 400AMP battery disconnect switch in them. Our team will be sending out all instructions and parts needed to exchange the battery disconnect switches to dealers and customers. We will direct customers to go to a dealer and we will be taking care of the cost on all exchanges. How Remedy Component Differs from Recalled Component : Identify How/When Recall Condition was Corrected in Production : The 400AMP battery disconnect switch will replace the 250AMP battery disconnect switch. This will allow all components to function as they should in the lithium upgrade models.
The E&I team made the correction the week of January 14th. The only change they needed to make was the exchange of the battery disconnect switches. The information contained in this report was submitted pursuant to 49 CFR §573 Part 573 Safety Recall Report 24V-150
Page 3
The information contained in this report was submitted pursuant to 49 CFR §573
Recall Schedule :
Description of Recall Schedule : There will be a dealer notification letter and a customer notification letter
sent our regarding this safety recall.
Planned Dealer Notification Date : MAR 01, 2024 – MAR 08, 2024
Planned Owner Notification Date : MAR 01, 2024 – MAR 08, 2024
* NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004
Part 573 Safety Recall Report 24V-150
The information contained in this report was submitted pursuant to 49 CFR §573
Manufacturer Name : Submission Date :
Pleasant Valley Teardrop Trailers LLC MAR 18, 2024 NHTSA Recall No. : 24V-150 Manufacturer Recall No. : NR Manufacturer Information :
Manufacturer Name : Pleasant Valley Teardrop Trailers LLC Address : 661 Belden Parkway NE
PO Box 395 Sugarcreek OH 44681
Company phone : 8524811 Population :
Number of potentially involved : 163 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2023-2024 nuCamp TAB 400, Cirrus 820 & 620 Vehicle Type : TRAILERS Body Style : OTHER Power Train : NR
Descriptive Information : – These units were selected because they were designated as Lithium Upgrades models. – A 250AMP Battery Disconnect was used during production of the Lithium Upgrade models. A 400AMP Battery Disconnect should have been used during production – There are 163 units affected overall in 2023 & 2024 model years. 2023 Cirrus 820 – 23 2023 Cirrus 620 – 17 2023 TAB 400 – 95 2024 Cirrus 820 – 8 2024
Cirrus 620 – 2 2024 TAB 400 – 18
Production Dates : JUL 22, 2022 – DEC 12, 2023
VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect :
Description of the Defect : These Lithium Upgrade units were produced with a 250AMP Battery Disconnect Switch. These units should have had a 400AMP Battery Disconnect installed during production.
FMVSS 1 : NR FMVSS 2 : NR
Description of the Safety Risk : If the system would consistently draw over 275AMPS then it would cause the 250AMP Battery Disconnect to overheat and potentially cause wires to melt.
Description of the Cause : Production Install Error
Identification of Any Warning
that can Occur :
NR Part 573 Safety Recall Report 24V-150 Page 2 Involved Components : Component Name 1 : BEP Battery Disconnect Switch Component Description : Battery Disconnect Switch Component Part Number : 48-00-2928 701B Supplier Identification : Component Manufacturer
Name : Pleasant Valley Teardrop Trailers Address : 661 Belden Parkway
Sugarcreek 44681
Country : NR Chronology :
Our E&I department was administering a test on our lithium battery system and noticed the 250AMP battery disconnect would become warm if there were multiple components running off the lithium system at the same time. They determined that if the system was drawing 275AMP consistently then it would cause the battery disconnect to overheat and the possibility of wires melting. – The E&I team felt is was necessary to upgrade the battery disconnect to a 400AMP battery disconnect switch which would allow the system to function without any concerns. – The E&I team has put together instructions to complete the exchange of the 250AMP battery disconnect to the 400AMP disconnect. Description of Remedy :
Description of Remedy Program : Our production team installed a 250AMP battery disconnect switch
incorrectly on the lithium upgrade units. The lithium upgrade units should have a 400AMP battery disconnect switch in them. Our team will be sending out all instructions and parts needed to exchange the battery disconnect switches to dealers and customers. We will direct customers to go to a dealer and we will be taking care of the cost on all exchanges. How Remedy Component Differs from Recalled Component : Identify How/When Recall Condition was Corrected in Production : The 400AMP battery disconnect switch will replace the 250AMP battery disconnect switch. This will allow all components to function as they should in the lithium upgrade models.
The E&I team made the correction the week of January 14th. The only change they needed to make was the exchange of the battery disconnect switches. The information contained in this report was submitted pursuant to 49 CFR §573 Part 573 Safety Recall Report 24V-150
Page 3
The information contained in this report was submitted pursuant to 49 CFR §573
Recall Schedule :
Description of Recall Schedule : There will be a dealer notification letter and a customer notification letter
sent our regarding this safety recall.
Planned Dealer Notification Date : MAR 05, 2024 – MAR 08, 2024
Planned Owner Notification Date : MAR 05, 2024 – MAR 08, 2024
* NR – Not Reported
**************************************************************************************************************
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END