“This site contains affiliate links for which OEMDTC may be compensated” |
January 6, 2023 NHTSA CAMPAIGN NUMBER: 23V002000
Battery Disconnect Switch May Short
An electrical short-circuit can increase the risk of a fire.
NHTSA Campaign Number: 23V002
Manufacturer Triple E Recreational Vehicles
Components ELECTRICAL SYSTEM, EQUIPMENT
Potential Number of Units Affected 341
Summary
Triple E Recreational Vehicles (Triple E) is recalling certain 2021-2022 Unity U24IB and 2021-2023 Unity U24TB motorhomes. The battery disconnect switch terminal posts may contact the metal grounded fridge frame, causing a short and blowing a 100 AMP fuse.
Remedy
Dealers will install two rubber terminal post protective covers, free of charge. Owner notification letters were mailed January 17, 2023. Owners may contact Triple E customer service at 1-877-992-9906. Triple E’s number for this recall is CA#10253-1.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
SOP09174
QAAR 10253 Battery Disconnect Terminal Post Protection
Tools Required
#2 Robertson (Square) Screw Driver
#1 Robertson (Square) Screw Driver
Small Flat Head Screw Driver
Turn OFF the propane supply.
Disconnect the shore power plug on the exterior of the coach and turn off the battery disconnect switch.
Disconnect the main negative cable on the house batteries.
Caution:
Failure to do so may result in damage to the fridge as it is removed.
Remove the screw from the lower fridge vent with a #2 Robertson driver.
Push the clips up.
With both clips up, remove the vent by pulling on the left side of the vent and then sliding it out. Set vent aside.
Be aware that there a re some wires at the back of the fridge that are bundled together and will need to be released before moving the fridge.
Open the refrigerator & freezer doors and remove the screw covers one side at a time.
Set covers aside
Remove all Six (6) mounting screws with a #1 Robertson screw driver.
Close the refrigerator doors and pull the fridge slowly into the coach 50mm (2″) to allow access to the battery disconnect.
Caution: do not move the fridge too much as it may dislodge the propane connection in the back.
Slip the rubber terminal post protective covers over the battery disconnect terminal posts.
Gently push the Fridge back into the cabinet until the main body is flush with the cabinet face.
Visually check to make sure that there is no interference with the gasket and it is contacting the backside of the fridge.
Reinstall the 6 mounting screws and caps.
Reinstall the negative cable on to the coach batteries and resecure the wiring on the back of the fridge.
Reinstall vent by lining up the tabs on the right side of the frame with the slots in the grill and swivel the left side in.
Push both clips down and reinstall the top clip screw of the vent. Start screw by hand into the metal bracket on the vent frame. Be careful not to strip the screw or overtighten and crack the plastic.
Verify fridge vent cover is secure by grasping the vent louvers and gently pulling on them to check the right side tabs engaged correctly.
Caution: failure to perform this may result in the vent dislodging during driving.
Chronology :
DECEMBER 21/2022 – A MOTORHOME IN THE PRODUCTION PROCESS SHORTED THE CIRCUIT AND BLEW A 100 AMP FUSE. THE CAUSE WAS THE BATTERY DISCONNECT TERMINAL POST HAD MADE CONTACT WITH THE METAL FRIDGE FRAME CAUSING THE SHORT CIRCUIT. THE FRIDGE HAD BEEN INSTALLED IN THE FRIDGE CABINET CROOKED CAUSING LESS SPACE FOR THE TERMINAL POSTS. IT WAS NOTICED THAT THE FRIDGE CABINET DRAWING HAD NOT BEEN UPDATED TO REFLECT A THICKER MATERIAL BEING USED IN THE PRODUCTION OF THE CABINET. THUS CAUSING LESS SPACE BETWEEN THE TERMINAL POSTS & THE FRIDGE FRAME.
3 Affected Products
Vehicle
MAKE | MODEL | YEAR |
TRIPLE E | UNITY | 2021-2023 |
10 Associated Documents
Recall Acknowledgement
RCAK-23V002-5230.pdf 645.818KB
Remedy Instructions and TSB
RCRIT-23V002-6320.pdf 2255.835KB
Manufacturer Notices(to Dealers,etc)
RCMN-23V002-7566.pdf 622.892KB
Defect Notice 573 Report
RCLRPT-23V002-1889.PDF 214.158KB
Miscellaneous Document – Recall CA#10253-1 – Return Form – USA
RMISC-23V002-5755.pdf 77.462KB
Part 577 Owner Notification Envelope
RONE-23V002-2446.pdf 240.908KB
ISSUED Owner Notification Letter(Part 577)
RCONL-23V002-1384.pdf 994.335KB
Recall Quarterly Report #1, 2023-1
RCLQRT-23V002-1371.PDF 211.141KB
Recall Quarterly Report #2, 2023-2
RCLQRT-23V002-0085.PDF 211.241KB
Recall Quarterly Report #3, 2023-3
RCLQRT-23V002-4402.PDF 211.463KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=23V002&docType=RCL
- Heavy Duty: ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits, equiped with 4 sets of bolts.
- Operation: On/Off 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.
- Compatible: used for DC 12 - 48 V systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.
- Purpose: eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.
- Copper terminal stud size: 3/8" (10 mm) x 2, very easy to install, universal used for car, vehicle, Rv and boat, also electrical equipment's switch.
- Heavy Duty: ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits, equipped with 4 sets of bolts.
- Operation: On/Off 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.
- Compatible: used for DC 12 - 48V systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.Its purpose is to eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.
- Widely used for car, marine boat, RV, camper, travel trailer, truck, ATV, UTV, battery banks and other devices.
- Package include:1x On/Off battery switch,4 bolts incuded.
- Operation: used for DC 12-24 V systems, On/Off 2 position, rated current: 100A (12V ), Max. withstanding current: 150A (12V ).
- Heavy Duty: ABS plastic and solid brass nuts / washers, rust and corrosion resistant, durable made for safety use.
- Convenience: easy to install & simple to use, 2 removable keys, waterproof cover for key hole.
- Purpose: used for battery to isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.
- Size: 2 brass terminals: 3/8", 2 mounting holes: 3/16". Used for Car, Vehicle, RV and Boat, also electrical equipment's switch.
- Convenience: direct fit and no modifications, hook up to TOP post battery negative directly, do not need additional battery cables or lugs, isolate and secure the electrical system easily.
- Operation: used for DC 12 - 48 V systems, ON/OFF 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.
- Heavy Duty: ABS plastic housing, durable made for safety use. Extended the top post battery negative to original size: standard top post negative (17 mm cone/tapering negative (-)), installation space should be checked.
- Compatible: used for standard top post battery (19 mm cone/tapering positive & 17 mm cone/tapering negative). Can stand alone or be locked together with other switch.
- Purpose: eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely, widely used for car, vehicle, Rv and boat.
- 【Compatible】- The battery disconnect switch is used for top post terminal(0.59''- 0.67'' cone battery negative post only). Compatible the condition of 12V voltage, 125A rated current, heavy duty.
- 【High Quality】- Our solid brass 12v battery disconnect switch with stainless steel fasteners provide excellent oxidation resistance and corrosion resistance, no need to worry about its service life.
- 【Easy to Use】Knob type design to disconnect or connect battery, just follow the direction instructions on the switch, unscrewing or tightening the battery switch into an “on” or “off” position to control current.
- 【Protect Battery】This battery shut off switch is designed to cut-off power flowing to the battery, avoid unwanted battery consumption when not used for long periods of time, extend the life of battery.
- 【Widely Applications】- Suitable for Car, Marine,tractor, camper, boat, RV, truck batteries which have a standard 0.59''-0.67''(15-17 mm) cone top post terminal, also used for electrical equipment.
- Heavy Duty: ABS plastic Battery Disconnect Isolator Master Switch with 2 Removable Key Rust and corrosion resistant, Solid cooper nuts and brass washers
- Operation: 2 brass Copper pillar: 0.33"/8mm. used for DC 12-24 V systems, On/Off 2 position, rated current: 100A (12V ), Max. withstanding current: 200A (12V ).
- Easy operation: disconnect and reconnect battery by one simple turn of the knob on it.The key Can Be Taken Down When There is No Power Connection.In this way,Power Supply Will Not Be Viciously Switched On.Waterproof Case Can Better Protect Key Hole.
- Purpose: Disconnects the battery safely,to eliminate any power draw from the battery when vehicle or boat is not in use,sleek modern appearance,sturdy and durable,Widely Used For Car,Marine,Boat,RV,Camper,Truck,ATV, UTV,Battery Banks And Other 12-24V Devices.
- After-sales Service: We provide 1 years’ warranty for all of our products since the purchasing day
- Easy to Use: Turning it on powers up your system, turning it off cuts the power.It can handle 275 Amps of continuous DC power for up to 1 hour, 455 Amps intermittently for 5 minutes, and 1250 Amps for cranking power lasting 10 seconds. It has 2x3/8" (10mm) studs.
- Sturdy Construction: This battery disconnect switch is built with a tough ABS plastic housing, tinned copper studs, and nuts. It includes 4 stainless steel mounting screws and caps for secure installation. You can easily access battery cables with 4 removable side plates.
- Safety First: The battery shut-off switch disconnects your battery safely, preventing excessive drain when your vehicle or boat isn't in use.
- Versatile Compatibility: This quick disconnect switch is designed for 12-48V DC systems, allowing you to isolate and secure your electrical system. It can work independently or be locked together with other switches, offering a simple and cost-effective way to separate batteries.
- Wide Range of Uses: This universal switch is suitable not just for cars, RVs, trucks, and marine boats but also for various electrical equipment, like flashing lights, chassis lights, fog lights, and dome lights.
- Battery Disconnect Switch: Marine Battery Switch Easy To Install 12V 24V 48V Battery Switch with On/Off position in clear color labels. Switch OFF = No power (red) to the cut-off circuit, Switch ON=Power (green) to closed circuit. Rating: 275 A continuous at DC 12V, 455 A Intermittent at DC 12V, 1250 A momentary at DC 12V..
- WaterProof: Battery Disconnect Switch Marine Battery Switch is made of ABS plastic housing and copper tin plating inner stud. Fully enclosed design to protect wiring from dirt, corrosion and rain.
- Comprehensive Safety: When Camper RV boat Truck Travel Trailer not in use, disconnecting the power will prevent the battery from draining. If the battery is not disconnected, it will continue to drain until the battery is depleted. When you come back to drive the car for a few months or even six months, the car will no longer be able to fire up. When the vehicle breaks down for maintenance, you can disconnect the current without having to remove the battery clamps.
- Wide Application: Heavy Duty Marine Battery Switch Easy to disconnect power, Good isolator for Travel Trailer Camper RV Boat Car trolling motor, Please Disconnect batteries befor you start.
- What You Get: Give you Nice 1 Pack Switches, 4 Pcs 2*3/8 Copper Lugs, 4 Pcs Heatshrink and for your cables, a Hex Wrench which can provide great convenience for your installation.
- Compatible: with a long bolt, used for side post terminal, battery side post with 3/8" hole only, recommended to mount on NEGATIVE battery post, DC 12V-24V system, 200A continuous and 600A momentary at DC 12V, on/off 2 position.
- Convenience: knife blade type, easy to install & simple to use. Lift the knife, then power will cut.
- Heavy Duty: solid brass made, rust and corrosion resistant, durable made for safety use.
- Purpose: used for battery to isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.
- Compatible with GM side post batteries or other batteries which have a 3/8" side post terminal, also used for electrical equipment.
- MORE STURDY, BETTER CONDUCTIVITY: Compared with the traditional ABS plastic shell material, the heavy duty cut off switch uses a better nylon 66 shell, high temperature resistance effect is better, more safe to use; The internal screw of the cutoff switch uses copper plated silver + silver contacts, which has better electrical conductivity, oxidation resistance and longer service life.
- LED DIGITAL VOLTMETER DISPLAY: The battery isolator switch surface is equipped with an LED display, which displays the current voltage status in real time, allowing you to better monitor the battery status at any time. When the battery switch is on, the upper button screen monitors the voltage in real time. When the master disconnect switch is off, the screen does not display.
- COMPATIBILITY & SAFETY: This Battery Kill Switch Used for DC 5 - 60V systems to isolate and secure the electrical system; eliminate any power draw from the battery when vehicle is not in use, disconnects the battery safely; provide a reliable way to shutdown electrical power during maintenance and protect batteries from excessive drain.
- EASY TO OPERATE: On/Off 2 position, Suitable for various 6V/12V/24V/48V/60V systems. Current: 250A Continuous at DC 12V; 300A for 30 minutes. Clockwise to turn on , counter clockwise to turn off.
- WIDE APPLICATION: Battery isolator switch is universal used for RV, Marine, Car, Boat, Camper, Travel Trailer, Truck, ATV, UTV battery and other engine application, makes it an effortless job of turning the battery on and off.
Last update on 2024-04-16 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
RECALL NOTIFICATION CA#10253-1 – RETURN FORM
Please complete this form indicating Recall Notification CA#10253-1 has been performed
in accordance with this Recall. E-mail completed form to recalls@tripleerv.com
Customer Name: «Owner_Name»
Serial # «VIN»
Coach Serial #«Serial»
Address (if different) Date Recall Completed Signature of Customer: Brad Wall
Customer Service / Warranty Manager
**************************************************************************************************************
1 2 3
4 5 6
7 8 9
•
•
•
1 2
TRIPLE E
RECREATIONAL VEHICLES
Terminal Post Protective
Covers
SOP09174 Department: 31
People Required: 1
QAAR 10253 Battery Disconnect
Terminal Post Protection
Time to Complete: 0.50 hours
Date Created: Jan. 4, 2023
Date Revised: Rev#:
Created by Initial: GK Verified: BH
Tools Required
#2 Robertson (Square)
Screw Driver
#1 Robertson (Square)
Screw Driver
Small Flat Head Screw
Driver
Disconnect
the main
negative
cable on the
house
batteries.
Caution:
Failure to do
so may
result in
damage to
the fridge as
it is
removed.
Be aware that
there a re some
wires at the back
of the fridge that
are bundled
together and will
need to be
released before
moving the fridge.
Turn OFF the propane supply.
Remove the screw
from the lower fridge
vent with a #2
Robertson driver.
Push the clips up.
Open the
refrigerator & freezer
doors and remove
the screw covers
one side at a time.
Set covers aside
Page 1 of 2
Disconnect the shore power plug on the exterior of the coach and
turn off the battery disconnect switch.
With both clips up, remove the vent by pulling on the left side of the
vent and then sliding it out. Set vent aside.
Remove all Six (6)
mounting screws with a
#1 Robertson screw
driver.
10 11 12
13 14 15
16 17 18
SOP09174 Department: 31
People Required: 1
TRIPLE E
RECREATIONAL VEHICLES
QAAR 10253 Battery Disconnect
Terminal Post Protection
Time to Complete: 0.50 hours
Date Created: Jan. 4, 2023
Date Revised: Rev#:
Created by Initial: GK Verified: BH
Close the refrigerator doors and pull
the fridge slowly into the coach 50mm
(2″) to allow access to the battery
disconnect.
Caution: do not move the fridge too
much as it may dislodge the propane
connection in the back.
Visually check to
make sure that there
is no interference with
the gasket and it is
contacting the
backside of the fridge.
Reinstall vent by lining up the tabs on the right side of the frame with
the slots in the grill and swivel the left side in.
Slip the rubber terminal post protective covers over the battery
disconnect terminal posts.
Reinstall the 6
mounting screws and
caps.
c- _”)
Push both clips down and reinstall the top clip screw of the vent. Start
screw by hand into the metal bracket on the vent frame. Be careful
not to strip the screw or overtighten and crack the plastic.
Page 2 of 2
Gently push
the Fridge
back into the
cabinet until
the main body
is flush with the
cabinet face.
Reinstall the negative cable on to the coach batteries and
resecure the wiring on the back of the fridge.
Verify fridge vent cover is
secure by grasping the vent
louvers and gently pulling on
them to check the right side
tabs engaged correctly.
Caution: failure to perform
this may result in the vent
dislodging during driving.
**************************************************************************************************************
LEISURE
TRAVEL VANS
Triple E Recreational Vehicles
A Division of Triple E Canada Ltd.
P: 204 325 4361
F: 204 325 5241 301 Roblin Blvd.
P.O. Box 1230 Winkler, Manitoba CA R6W 4C4 U.S. Mailing:
P.O. Box 68 Walhalla, ND 58282 LEISUREVANS.COM TRIPLEERV.COM
IMPORTANT SAFETY RECALL
«Owner Name»
«Address1»
«Address2 »
«Address3 », «Prov» «Postal Code»
“This notice applies to your vehicle, «Unit»
VIN #«VIN»
Coach Serial #«Serial» Triple E Recreational Vehicles Recall CA#10253-1
January 9, 2023
NHTSA #23V002 This notice is sent to you in accordance with the requirements of the National Traffic & Motor Vehicle Safety Act. Triple E Recreational Vehicles has decided that a defect exists in certain 2021, 2022 & 2023 Unity U24IB & Unity U24TB motorhomes manufactured between June 17, 2020 and December 1, 2022 Description of Defect: The battery disconnect switch, located at the entry door, the terminal posts in the fridge cabinet at the entry door, may contact the grounded metal fridge frame resulting in a short circuit. If the battery disconnect switch terminal posts would contact the metal fridge frame it would cause a short in the circuit and blow a fuse and possibly causing an increased risk of fire and injury. To Have This Modification Performed: We request your assistance to have this Safety issue corrected. Please have the rubber terminal post protective covers installed, included in this mailing. When the covers have been installed, complete the enclosed return form and email to recalls@tripleerv.com.
If you choose to have your selling dealer or a RV service center perform the recall it will be performed at no charge to you. The time needed to perform the recall is
approximately 30 minutes. If you choose to have this Recall performed by a service center other than your dealer, prior authorization is required.
1 of2 If you had this repair performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. For more information contact Triple ERV/Leisure Travel Vans at 1-877-992- 9906 Customer Service/ Warranty department or by e-mail recalls@tripleerv.com in the subject line “Recall CA#l0253-1”. What if you are a Lessor?
Federal law requires that you forward a copy of this safety recall notice to the lessee within ten working days. If you no longer own this vehicle, please complete the return form stating “No Longer Own this Vehicle” or provide the new owners contact information and submitting to Customer Service at recalls@tripleerv.com For U.S. Residents If Triple E Recreational Vehicles fails or is unable to remedy this potential defect without charge, you may submit a written complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave. SE, Washington, DC 20590 or call the toll free Vehicle Safety Hotline at 1-888-327- 4236; (TTY: 1-800-424-9153) or go to http://www.safercar.gov We regret the inconvenience this Recall may cause you but want you to have complete satisfaction with your Leisure Travel Vans product. Thank you for your anticipated assistance and please do not hesitate to contact us should you require additional information.
Sincerely, Brad Wall
Customer Service/ Warranty Manager
BW/wcw Enclosures
1 – SOP (Standard Operating Procedure)
2 – rubber terminal post protective covers
2 of2
**************************************************************************************************************
LEISURE
TRAVEL VANS
Triple E Recreational Vehicles
A Division of Triple E Canada Ltd.
P: 204 325 4361
F: 204 325 5241 301 Roblin Blvd.
P.O. Box 1230 Winkler, Manitoba R6W 4C4
CA U.S. Mailing:
P.O. Box 68 Walhalla, ND 58282 LEISUREVANS.COM TRIPLEERV.COM
IMPORTANT SAFETY RECALL
«Dealer»
“This notice applies to this vehicle, «ProductLine»
VIN #«Vin»
January 9, 2023
Coach #«UNIT CoachID» Triple E Recreational Vehicles Recall CA#10253-1 NHTSA #23V002 This notice is sent to you in accordance with the requirements of the National Traffic & Motor Vehicle Safety Act. Triple E Recreational Vehicles has decided that a defect exists in certain 2021, 2022 & 2023 Unity U24IB & Unity U24TB motorhomes manufactured between June 17, 2020 and December 1, 2022 Description of Defect: The battery disconnect switch, located at the entry door, the terminal posts in the fridge cabinet at the entry door, may contact the grounded metal fridge frame resulting in a short circuit. If the battery disconnect switch terminal posts would contact the metal fridge frame it would cause a short in the circuit and blow a fuse and possibly causing an increased risk of fire and injury. To Have This Modification Performed: We request your assistance to have this Safety issue corrected. Install the rubber terminal post protective coverings on the terminal posts of the battery disconnect switch, which are included in this mailing. Follow the SOP included to complete as required.
For reimbursement submit a warranty application for Labour to perform this Recall: 0.5 hr./ unit
1 of2 For more information contact Triple ERV/Leisure Travel Vans at 1-877- 992-9906 Customer Service/ Warranty department or by e-mail recalls@tripleerv.com in the subject line “Recall CA#10253-1”. Thank you for your anticipated assistance and please do not hesitate to contact us should you require additional information.
Sincerely, Brad Wall
Customer Service/ Warranty Manager
BW/wcw Enclosures
1 – SOP (Standard Operating Procedure) 2 – rubber terminal post protective covers
2 of2
**************************************************************************************************************
OMB Control No.: 2127-0004
Part 573 Safety Recall Report 23V-002
The information contained in this report was submitted pursuant to 49 CFR §573
Manufacturer Name : Submission Date :
Triple E Recreational Vehicles JAN 06, 2023 NHTSA Recall No. : 23V-002 Manufacturer Recall No. : CA#10253-1 Manufacturer Information :
Manufacturer Name : Triple E Recreational Vehicles Address : PO Box 1230 Winkler MB
Canada 00 R6W 4C4
Company phone : 204-325-4361
Population :
Number of potentially involved : 341 Estimated percentage with defect : 100 %
Vehicle Alterer Information :
Vehicle 1 : 2021-2022 UNITY U24IB
Descriptive Information : THE BATTERY DISCONNECT SWITCH, LOCATED IN THE FRIDGE CABINET
AREA , IS INSTALLED TOO CLOSE TO THE METAL FRIDGE FRAME. THE SWITCH TERMINAL POSTS MAY CONTACT THE FRIDGE FRAME CAUSING A SHORT IN THE CIRCUIT AND BLOWING A 100 AMP FUSE. THE MODELS NOT INCLUDED HAVE THE BATTERY DISCONNECT SWITCH LOCATED IN A DIFFERENT AREA OF THE FRIDGE CABINET NOT CLOSE TO THE METAL FRAMING OF THE FRIDGE. UNITS AFFECTED 75
Production Dates : JUN 17, 2020 – DEC 01, 2022 Vehicle 2 : 2021-2023 UNITY U24TB
Descriptive Information : THE BATTERY DISCONNECT SWITCH, LOCATED IN THE FRIDGE CABINET AREA, THE TERMINAL POSTS ARE TOO CLOSE TO THE METAL FRIDGE FRAME. THE SWITCH TERMINAL POSTS MAY CONTACT THE FRIDGE FRAME CAUSING A SHORT IN THE CIRCUIT AND BLOWING A 100 AMP FUSE. THE MODELS NOT INCLUDED HAVE THE BATTERY DISCONNECT SWITCH LOCATED IN A DIFFERENT AREA OF THE FRIDGE CABINET NOT CLOSE TO THE METAL FRAMING OF THE FRIDGE.
UNITS AFFECTED 266
Production Dates : JUN 17, 2020 – DEC 01, 2022 Description of Defect :
Description of the Defect : THE BATTERY DISCONNECT SWITCH, LOCATED AT THE ENTRY DOOR, THE TERMINAL POSTS CAN CONTACT THE METAL GROUNDED FRIDGE FRAME RESULTING IN A SHORT CIRCUIT AND BLOWING A 100 AMP FUSE.
FMVSS 1 : NR
FMVSS 2 : NR Part 573 Safety Recall Report 23V-002 Page 2 Description of the Safety Risk : IF THE BATTERY DISCONNECT SWITCH TERMINAL POSTS WOULD
CONTACT THE METAL FRIDGE FRAME IT COULD CAUSE A SHORT IN THE CIRCUIT AND BLOW THE FUSE AND POSSIBLY CAUSING AN INCREASED RISK OF FIRE AND INJURY.
Description of the Cause : A DESIGN OVERSIGHT AND NOT UPDATING CABINET ASSEMBLY DRAWINGS TO COMPENSATE FOR THE USE OF PLYWOOD WHICH IS A THICKER MATERIAL. THERE IS INSUFFICIENT ROOM FROM THE TERMINAL POSTS AND THE METAL FRIDGE FRAME. Identification of Any Warning
that can Occur : THE 100 AMP FUSE IN THE MEGA FUSE HOLDER IN THE BATTERY COMPARTMENT WOULD HAVE BLOWN. Involved Components : Component Name : BATTERY DISCONNECT TERMINAL
Component Description : BATTERY DISCONNECT CONNECTION Component Part Number : 126-0763 Supplier Identification : Component Manufacturer
Name : NR Address : NR
NR
Country : NR Chronology :
DECEMBER 21/2022 – A MOTORHOME IN THE PRODUCTION PROCESS SHORTED THE CIRCUIT AND BLEW A 100 AMP FUSE. THE CAUSE WAS THE BATTERY DISCONNECT TERMINAL POST HAD MADE CONTACT WITH THE METAL FRIDGE FRAME CAUSING THE SHORT CIRCUIT. THE FRIDGE HAD BEEN INSTALLED IN THE FRIDGE CABINET CROOKED CAUSING LESS SPACE FOR THE TERMINAL POSTS. IT WAS NOTICED THAT THE FRIDGE CABINET DRAWING HAD NOT BEEN UPDATED TO REFLECT A THICKER MATERIAL BEING USED IN THE PRODUCTION OF THE CABINET. THUS CAUSING LESS SPACE BETWEEN THE TERMINAL POSTS & THE FRIDGE FRAME. The information contained in this report was submitted pursuant to 49 CFR §573 Part 573 Safety Recall Report 23V-002
Page 3
The information contained in this report was submitted pursuant to 49 CFR §573
Description of Remedy :
Description of Remedy Program : DEALERS WITH INVENTORY WILL BE SENT AN SOP (STANDARD
OPERATING PROCEDURE) AND TWO RUBBER TERMINAL POST PROTECTIVE COVERS PER MOTORHOME TO BE INSTALLED. DEALERS WILL SUBMIT A WARRANTY APPLICATION FOR REIMBURSEMENT. RETAIL OWNERS WILL BE SENT AN SOP (STANDARD OPERATING PROCEDURE) AND TWO RUBBER TERMINAL POST PROTECTIVE COVERS. THE RETAIL OWNER WILL BE REIMBURSED OR THE SERVICE CENTER WILL BE PAID DIRECTLY BY TRIPLE E RV. A RETAIL OWNER OR SERVICING CENTER WILL BE REIMBURSED FOR COSTS INCURRED FOR REPAIR PRIOR TO THE RECALL NOTIFICATION. How Remedy Component Differs from Recalled Component : Identify How/When Recall Condition was Corrected in Production : TWO RUBBER TERMINAL POST PROTECTIVE COVERS WILL BE INSTALLED ON THE TERMINAL POSTS OF THE BATTERY DISCONNECT SWITCH
ON DECEMBER 21/2022 DURING THE MANUFACTURING PROCESS, TWO RUBBER TERMINAL POST PROTECTIVE COVERS WERE INSTALLED ON EACH MOTORHOME. THE DESIGN TEAM WILL UPDATE THE CABINET DRAWING FOR THE UNITY U24TB TO MOVE THE BATTERY DISCONNECT TO THE FRIDGE EXHAUST/VENT CHAMBER AS IN ALL OTHER MODELS MANUFACTURED. THE UNITY U24IB IS NO LONGER BEING MANUFACTURED. Recall Schedule :
Description of Recall Schedule : NOTIFICATION TO DEALERS IS EXPECTED TO OCCUR LATE JANUARY /
2023.
NOTIFICATION TO RETAIL OWNERS IS EXPECTED TO OCCUR LATE JANUARY / 2023.
Planned Dealer Notification Date : JAN 25, 2023 – JAN 25, 2023
Planned Owner Notification Date : JAN 25, 2023 – JAN 25, 2023 Purchaser Information :
The following manufacturers purchased this defective/noncompliant equipment for possible use or installation in new motor vehicles or new items of motor vehicle equipment:
Name : Address :
Country : Company Phone :
* NR – Not Reported
SEOCONTENT-END