22526 Fuel Vapor Line Without Heat Shielding Installed – 2023 IC Bus CE

“This site contains affiliate links for which OEMDTC may be compensated”

November 23, 2022 NHTSA CAMPAIGN NUMBER: 22V872000

Fuel Vapor Line Without Heat Shielding Installed

Heat exposure may cause the line to leak, increasing the risk of a fire.

 

NHTSA Campaign Number: 22V872

Manufacturer Navistar, Inc.

Components FUEL SYSTEM, GASOLINE

Potential Number of Units Affected 196

 

Summary

Navistar, Inc. (Navistar) is recalling certain 2023 IC CE vehicles. The fuel vapor line without the heat shield tubing may have been installed, exposing the line to heat from the exhaust system.

 

Remedy

Dealers will replace the fuel vapor line with heat shield tubing, free of charge. Owner notification letters are expected to be mailed January 20, 2023. Owners may contact Navistar’s customer service at 1-800-448-7825. Navistar’s number for this recall is 22526.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.

 


DEFECT DESCRIPTION

A fuel vapor line may have been built without the heat shield installed. Exposure to exhaust system temperatures in certain areas over time can cause the line to break down and possibly leak. A fuel vapor line that breaks down and leaks can increase the risk of a vehicle fire resulting in property damage.

 

MODELS INVOLVED

This safety recall involves certain 2023 IC Buse CE Series school bus models built 06/21/2022 thru 09/08/2022 with feature code 12DLP (ENGINE, GASOLINE).

 

PARTS INFORMATION

Part Number Part Description Quantity
306132C1 STRAP, CABLE LOCK 14 in (355 mm) As Needed

 

SERVICE PROCEDURE

1. Park vehicle on flat surface.

2. Shift transmission to Park or Neutral and set parking brake.

3. Turn ignition to Key OFF position.

4. Install wheel chocks.

NOTE: There will be more cable straps on the vehicle you are working on than what are shown in Figure 1, Item 1.

5. Remove cable straps (Figure 1, Item 1) that route and secure fuel hoses.

6. Wrap fuel line heat shield around fuel vapor hose (Figure 1, Item 2).

7. Secure shield and hoses in place with new cable straps.

8. Remove wheel chocks.

 


Chronology :

  • 09/16/2022 – Navistar Supplier Quality send communication to Compliance describing the issue with the fuel vapor line.
  • 09/21/2022 – Navistar quarantines gas powered buses at the assembly plant.
  • 10/04/2022 – Navistar Supplier Quality, Compliance, and Aftersales meet and initiates investigation to the impact to IC gas powered buses.
  • 10/10/2022 – Navistar Engineering initiates investigation to determine long term affects of continued heat exposure to non-shielded fuel vapor hose.
  • 11/14/2022 – Navistar Engineering concludes analysis and shares data with Compliance.
  • 11/16/2022 – Navistar finalizes the suspect population.
  • 11/18/2022 – Navistar declares a Safety Recall. As of this time, no warranty claims or field failures for this defect have occurred.
  • 12/14/2022 – Navistar Compliance documents the field inspections found all rear wheel hub nuts were properly installed or have been repaired.
Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [176.03 KB]

 


1 Affected Product

Vehicle

MAKE MODEL YEAR
IC BUS CE 2023

 


6 Associated Documents

Recall Acknowledgement

RCAK-22V872-1876.pdf 645.748KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [630.61 KB]

 


Defect Notice 573 Report

RCLRPT-22V872-5470.PDF 213.868KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.86 KB]

 


Recall 573 Report – December 19, 2022

RCLRPT-22V872-9644.PDF 213.873KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.86 KB]

 


Recall 573 Report – December 19, 2022

RCLRPT-22V872-2890.PDF 213.994KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.98 KB]

 


Remedy Instructions and TSB

RCRIT-22V872-1442.pdf 180.258KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [176.03 KB]

 


ISSUED Owner Notification Letter(Part 577)

RCONL-22V872-2070.pdf 39.957KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [39.02 KB]

 


Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V872&docType=RCL

 


 

Bestseller No. 1
Heat Shroud Sleeve Aluminized Sleeving Express Aluminized Hose and Silver Hose Wire Protection Barrier with Hook and Loop Closure, 3/4" I.D.x 10FT- 1" I.D.x 10FT
  • 【HIGH PERFORMANCE FEATURE】Size:Width is 3.8 inch(95mm) ,Length is 118Inch/10FT(3M).Added convenience of a hook & loop closure design along the open edges.Without the need of removing one end of connected wires, cables and hoses, simply wrap Heat Shroud sleeves around whatever needs protection and close the edges.
  • 【EASY INSTALLATION】Pliable for tight bends,you can trim to desired length,very easy to intall and use it.
  • 【SUPERB CRAFTSMANSHIP】Titanium wrap is engineered to be stronger than most wraps and more for improved thermal performance and reliability. Aluminized Sleeving withstands 600 degrees F direct, continuous heat and 2000 degrees F radiant heat.But please stay away from open flames.
  • 【WIDELY APPLICATIONS】Our Heat Shroud Aluminized Sleeving Extremely pliable for a tight and secure wrap for expand and contract over fittings,cable,terminals and more.High resistance to abrasions, oil spills, temperatures and vibration breakdown.
  • 【TIPS】Please check the size of the products pictures,type and shape to make sure the aluminized sleeve is the one that you need.If You Have Any Problems ,Take Time To Contact With Us,We Are In 24 Hours Service !
Bestseller No. 2
Design Engineering 010418 Heat Sheath 1/2" I.D. x 3ft Aluminized Sleeving for Ultimate Hi-Temp Protection
  • Slide over wires, cables and hoses for extreme heat protection
  • Withstands 500 degrees F direct, continuous heat and 2000 degrees F radiant heat
  • Pliable for tight bends
  • Trim to desired length
  • Five popular diameters to choose from: 1/2", 3/4", 1", 1-1/4", and 1-1/2"
Bestseller No. 3
Heat Shield Sleeve Fuel Line Heat Shield Auto Hose Spark Plug Wire Cover Protectors Boots Roll 2500 Degree for Car&Auto Wire Loom Brake Cable (1" IDX10', Titanium)
  • 【Protection Wire】:Widely used as a solution to your burning spark plug wires which create a lot of heat. These universal spark plug wire cover can provide a good heat protection to spark plug wires especially on engines with excessive exhaust headers.
  • 【Perfect Use】:It also works well with 90 degrees, 45 degrees, and straight spark plug . Fits most hot rods and classics engine. Also fit for most angled & straight boots. Length is about 10Ft long.
  • 【 Materials】 :It is made with two layers of high temperature titanium material. The thick material is long enough to protect spark plug wires as it nears the header or exhaust manifold helping to increase longevity of wire and maintain maximize spark for as long as you keep your vehicle.It can withstand heat up to 2500 degrees intermittent.
  • 【Easy Installation】:The covers are easy to slip in the boot heat protector on to each boot of the spark plug wire. Just slip the large end (with the sewn stitching) over the boot. Then carefully slip the ringed end over the boot that connects to the product.
  • 【100% Guarantee】:We will refund you immediately if you don't satisfied with the item you received. You will enjoy 12 months long service. Any problem please feel free to contact us!
SaleBestseller No. 4
Wire Heat Shield Automotive Heat Shield Sleeve Fuel Line Heat Shield Titanium Auto Hose Spark Plug Wire Cover Protectors Boots Roll 2500 Degree for Car&Auto Wire Loom Brake Cable(1" I.D.X10FT)
  • 【Protection Wire】:Widely used as a solution to your burning spark plug wires which create a lot of heat. These universal spark plug wire cover can provide a good heat protection to spark plug wires especially on engines with excessive exhaust headers.
  • 【Perfect Use】:It also works well with 90 degrees, 45 degrees, and straight spark plug . Fits most hot rods and classics engine. Also fit for most angled & straight boots. Length is about 10Ft long.
  • 【 Materials】 :It is made with two layers of high temperature titanium material. The thick material is long enough to protect spark plug wires as it nears the header or exhaust manifold helping to increase longevity of wire and maintain maximize spark for as long as you keep your vehicle.It can withstand heat up to 2500 degrees intermittent.
  • 【Easy Installation】:The covers are easy to slip in the boot heat protector on to each boot of the spark plug wire. Just slip the large end (with the sewn stitching) over the boot. Then carefully slip the ringed end over the boot that connects to the product.
  • 【100% Guarantee】:We will refund you immediately if you don't satisfied with the item you received. You will enjoy 12 months long service. Any problem please feel free to contact us!
SaleBestseller No. 5
13mm - 1/2" Self Closed Aluminized Sleeve Heat Shield Protection Side Entry High Temp for Hoses, Wire Harnesses, Cables, Automotive, Exhaust 39" (1 Meter)
  • [Product Features] Adhesive wire heat shield wrap 1/2'' I.D, Working temperature: -40°C to + 150°C | Heat insulation performance: ≥100°C | Thermal insulation:Great protection in high temperature environments,Oil resistance good
  • [Material]: Side Entry Sleeve with 25% Overlap | Material: aluminum foil + fiberglass + polyester
  • [Widely used]: Use for heat insulation: high temperature resistance for automotive and insdustrial applications. Cable harnesses, cable and wire bundles, hoses, tubing, thermal wire wrap, heater hose wrap, cable heat sleeve
  • [Tips]: Please stay away from open flames. Our self-wrap heat shield sleeve is very convenient and fast, please check the size and pictures carefully before buying. If you have any questions, please contact us, we will be happy to provide you with the best service.
  • [What will you get]: Set includes: 1x self-wrap heat shield sleeve
Bestseller No. 6
uxcell Heat Shield Sleeve, 9.8Ft-7mm High Temp Silicone Resin Fiberglass Sleeve White
  • [PARAMETER] Material: Alkali-free Fiberglass, Silicone Resin; Length: 3.0 Meter / 9.8 Feet; Inner Diameter: 7mm; Working Temp Range: –60℃~+200℃; Working Voltage: 1200V; Flame Resistance: VW-1.
  • [FEATURE] This heat sleeve fiberglass are for high temperature applications, also, it keeps wire neat and organized.
  • [MADE] This product is made of alkali-free fiberglass. Then coated with a small amount of silicone resin. Lastly, process the pipe under a high temperature.
  • [APPLICATION] The heat shield tubing is mainly applied to insulate and heat equipment, such as motor, engine, plug wire, fuel lines, decorative light, etc.
  • [NOTE] Electrical wires should never be hot. Should increase the gauge of wire if you are exceeding the recommended load of that wire. This product would make the wire get hot by not letting it cool and might melt the insulation on said wire.
Bestseller No. 7
SUPERFASTRACING 5 Feet Heat Sleeve Fiberglass Adjustable Heat Shield Sleeve Black 5FT X 6MM(1/4") for Car Wire Loom
  • [Material]:The Heat Sleeve Fiberglass is mainly made of high quality fiber glass.
  • [Function]:It's can reduces radiant heat by up to 60%. Helps to prevent vapor lock, protects wires from melting. It is ideal for shieding fuel lines, helping to prevent vapor lock, protecting sensitive wire looms form close proximity heat, shielding brake lines and hose and stopping clutch cables from melting.
  • [Temperature range]:Heat Sleeve Fiberglass can withstands 1100¨H continuous and 2000¨H intermittent.
  • [Size]:5 Feet X 6mm (1/4 inch) Heat Sleeve Fiberglass Black
  • [Warning]:Always wear gloves and long sleeves are recommended when handling this product. And pay attention to eyes and respiratory protection
Bestseller No. 8
Heat Hose Fiberglass Wrap Shield Sleeve Wire Fuel Line Heat Shield Roll High Temp Black Colour Adjustable 10FT-13MM(1/2") for Car Wire Loom Protection
  • MATERIAL: The Heat Sleeve Fiberglass is mainly made of high quality fiber glass.It's can reduces radiant heat by up to 60%.
  • APPLICATION: Heat Sleeve Fiberglass can withstand 1100°F continuous and 2000°F intermittent.
  • EASY TO INSTALL: Our fiberglass sleeves are specially woven and can be expanded and shrunk by fittings, cables, terminals, etc. Simply pull the wires inside, AN hoses, cables, etc.
  • EFFECT:Helps prevent steam lock and prevent wire melting.It is best to wear long sleeved gloves when installing.
  • BEST SERVICE - If you have any questions about our Heat Hose Fiberglass Wrap, we will provide you with a refund service. If you have any questions, please contact us in time, we will do our best to serve you.
Bestseller No. 9
Heat Hose Fiberglass Wrap Shield Sleeve- 1/2" ID x 10'Black Adjustable Hose Heat Shield Spark Plug Wire fuel line heat shield Roll For Car Wire Loom cable Heat Shield Brake Line Cable Heat Shield
  • THIS BLACK AUTO WIRE HEAT SHIELD is mainly made of high quality fiber glass.Easy to installation.Simply pull the wires inside,AN hoses,cables etc.
  • Fiberglass Auto sleeving Withstands operating reflective temperature of 600℉continuous and 1100℉intermittent.
  • Black fiberglass hot rod car sleeve helps to prevent vapor lock, protects wires from melting, AN hoses,shields oil and brake lines.
  • Our fiberglass sleeving special weave that allows it to expand and contract over fittings,cable,terminals and more.
  • Caution: Keep it away from the open fire ! Capable of reducing up to 60 percentage of radiant heat.
Bestseller No. 10
Ummickl 3/4"(19.05mm)ID Fire Sleeve Heat Sleeve Heat Shielded Fire Thermo Armor Silicone Coated Fiberglass for Automotive Hose Lines & Electrical Wiring,5 feet (Black)
  • 【Application】—— Designed of silicone rubber coated fiberglass. Quality material to protect good heat insulation for hose wires fuel lines. Widely used to protect and bundling fuel lines, hydraulic and oil lines from high temperatures and to prolong the life of wiring and hoses.
  • 【Withstand High Temp】——Can withstand 500~2000 degree intermittent heat.
  • 【Dimension】—— Inner Diameter 3/4“ (19mm) , Length 5 Feet (1.5 m). Note: the size is measured by manual ,there may not be very exactly.
  • 【Easy to Use】——Easy to instal,Ideal for protecting hoses, electrical wiring, oil and fuel lines from heat and to prolong the life , helps to prevent vapor lock, protects wires from melting.
  • 【Lifetime Service】——You will enjoy 12 months service if you order this silicone coated fiberglass heat Shielded from our store. Any problem please feel free to contact us!

Last update on 2024-06-22 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

 


Leave a Comment

Share to...