“This site contains affiliate links for which OEMDTC may be compensated” |
September 30, 2022 NHTSA CAMPAIGN NUMBER: 22V751000
Rear Door Striker Bolt May Dislodge
Dislodged striker bolts can cause the rear door latch to fail, allowing the door to open during a crash, and increasing the risk of injury.
NHTSA Campaign Number: 22V751
Manufacturer Braun Ambulances
Components LATCHES/LOCKS/LINKAGES
Potential Number of Units Affected 1,240
Summary
Braun Ambulance (Braun) is recalling certain 2018-2022 Chief XL, Express, Express Plus, Liberty, Super Chief, TLC, and Signature Series ambulances. The rear door top striker bolts may become loose and dislodge while the vehicle is in motion.
Remedy
Dealers will inspect and replace the striker bolts, free of charge. Owner notification letters were mailed on October 17, 2022. Owners may contact Braun’s customer service at 1-877-344-9990. Braun’s number for this recall is 22-001.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
IMPORTANT SAFETY RECALL
Braun Recall Notice: TBD September 29, 2022
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Braun Industries has decided that a safety related defect may exist with some rear door top striker bolts. Braun striker pin part number 97136 may under certain conditions become loose and dislodge from the vehicle while in service.
In the affected vehicles, loose pins may result in the top of the rear doors not latching or unlatching. This can result in the door not staying closed or not able to be opened during vehicle operation. The door may not be fully latched increasing the likelihood of the door inadvertently opening in the event of a crash. Some pins may not present an issue at initial review, but nevertheless should be inspected and if necessary remedied. You are receiving this notice because Braun records indicate you may have received shipments of affected units.
Braun will remedy the affected units free of charge by replacing Braun striker pin 97136 with Braun striker pin 97259. Replacement pins are available as of October 3rd, 2022. Replacement is done by removing the affected pins and inspecting for obstructions in the area where the pin fastens and replacing the pin. Labor reimbursement for the inspection and repair for each ambulance replacement is 30 minutes. The replacement pins will be properly torqued and marked upon installation.
Affected Part: | Striker Pin | Part Number: 97136 |
Replacement Part: | Striker Pin | Part Number: 97259 |
Please contact Braun Industries to arrange inspection and replacement of the affected striker pins in your vehicle(s). The Braun Service contact information is as follows:
Phone: 877-344-9990 6:00 a.m. – 4:30 p.m. EDT,
Email: braunservice@braunambulances.com
It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by the notification under a sale or lease until the defect or noncompliance is remedied.
If Braun Industries is unable to arrange service as described above without charge within a 60 day period upon contacting Braun Industries, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, S.E., Washington, DC 20590 or call toll-free Auto Safety Hotline at 1-888327-4236 (TTY 1-800-424-9153); or go to http://www.safercar.gov.
Any lessor who receives a notification of a determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send a copy of such notice to the lessee of a leased motor vehicle, by first-class mail to the most recent lessee known to the lessor. Such notification shall be mailed within ten days of the lessor’s receipt of the notification from the vehicle manufacturer. This requirement applies to both initial and follow-up notifications but does not apply where the manufacturer has notified a lessor’s lessees directly.
We apologize in advance for the inconvenience this issue may cause your organization. We will make every effort minimize any inconveniences and to make this as simple as possible for both our Dealers and our Customers.
Sincerely,
Kim Braun
President – U.S. Division
IMPORTANT SAFETY RECALL
This notice applies to your vehicle(s) VIN,
Recall # 22V-751
Braun Recall Notice: 2022-01
September 29, 2022
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Braun Industries has decided that a safety related defect may exist with certain 2018-2022 Chief XL, Express Plus, Liberty, Super Chief, TLC ambulances and 2018-2021 Signature Series ambulances. The rear door top striker bolts may become loose and separate from the vehicle while it is in motion. As such, these vehicles fail to comply with the requirements of the Federal Motor Vehicle Safety Standard number 206, “Door Locks and Door Retention Components”.
In the affected vehicles, loose pins may result in the top of the rear doors not latching or unlatching. This can result in the door not staying closed or not able to be opened during vehicle operation. The door latch may separate from the vehicle while in motion, increasing the risk of a crash. Some pins may not present an issue at initial review, but nevertheless should be inspected and if necessary remedied. You are receiving this notice because Braun records indicate you may have received shipments of affected units.
Braun will remedy the affected units free of charge by replacing Braun striker pin 97136 with Braun striker pin 97259. Replacement pins are available as of October 3, 2022. Replacement is done by removing the affected pins and inspecting for obstructions in the area where the pin fastens and replacing the pin. Labor reimbursement for the inspection and repair for each ambulance replacement is 30 minutes. The replacement pins will be properly torqued and marked upon installation, free of charge
Affected Part: | Striker Pin | Part Number: 97136 |
Replacement Part: | Striker Pin | Part Number: 97259 |
Please contact Braun Industries to arrange inspection and replacement of the affected striker pins in your vehicle(s). The Braun Service contact information is as follows:
Phone: 877-344-9990 6:00 a.m. – 4:30 p.m. EDT,
Email: braunservice@braunambulances.com
It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by the notification under a sale or lease until the defect or noncompliance is remedied.
If Braun Industries is unable to arrange service as described above without charge within a 60 day period upon contacting Braun Industries, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, S.E., Washington, DC 20590 or call toll-free Auto Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153); or go to http://www.safercar.gov.
Any lessor who receives a notification of a determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send a copy of such notice to the lessee of a leased motor vehicle, by first- class mail to the most recent lessee known to the lessor. Such notification shall be mailed within ten days of the lessor’s receipt of the notification from the vehicle manufacturer. This requirement applies to both initial and follow-up notifications but does not apply where the manufacturer has notified a lessor’s lessees directly.
We apologize in advance for the inconvenience this issue may cause your organization. We will make every effort minimize any inconveniences and to make this as simple as possible for both our Dealers and our Customers.
Sincerely,
Kim Braun
President – U.S. Division
Braun Industries, Inc. 1170 Production Drive Van Wert OH 45891
Website: www.braunambulances.com | Phone: 419-232-7020 | Fax: 419-232-7070
Braun Customer Reimbursement Plan
Braun will remedy the affected units free of charge by replacing Braun striker pin 97136 with Braun striker pin 97259. Replacement is done by removing the affected pins and inspecting for obstructions in the area where the pin fastens and replacing the pin.
Labor reimbursement for the inspection and repair for each ambulance replacement is 30 minutes.
The replacement pins will be properly torqued and marked upon installation.
Affected Part: | Striker Pin | Part Number: 97136 |
Replacement Part: | Striker Pin | Part Number: 97259 |
Please contact Braun Industries to arrange inspection and replacement of the affected striker pins in your vehicle(s). The Braun Service contact information is as follows:
Phone: 877-344-9990 6:00 a.m. – 4:30 p.m. EDT,
Email: braunservice@braunambulances.com
Chronology :
May 2022 – Customer report of loose pins/pins dislodging in the field. Problem was corrected under warranty claim
July 2022 – Customer report of loose pins/pins dislodging in the field. Problem was corrected under warranty claim
July 2022 – transitioned to new striker pin 97259 to replace 97136,
August – September 2022 – evaluated failure modes of the 91736, improved install process of new striker.
September 2022 – arrived at decision to address field failures via recall and inspection/replacement of any of the 97136 strikers in the field.
35 Affected Products
Vehicles
MAKE | MODEL | YEAR |
BRAUN AMBULANCES | CHIEF XL | 2018-2022 |
BRAUN AMBULANCES | EXPRESS | 2018-2022 |
BRAUN AMBULANCES | EXPRESS PLUS | 2018-2022 |
BRAUN AMBULANCES | LIBERTY | 2018-2022 |
BRAUN AMBULANCES | SIGNATURE SERIES | 2018-2022 |
BRAUN AMBULANCES | SUPER CHIEF | 2018-2022 |
BRAUN AMBULANCES | TLC | 2018-2022 |
9 Associated Documents
Manufacturer Notices(to Dealers,etc)
RCMN-22V751-1205.pdf 141.651KB
Recall Acknowledgement
RCAK-22V751-6074.pdf 645.428KB
Noncompliance Notice 573 Report
RCLRPT-22V751-9590.PDF 219.283KB
Manufacturer Reimbursement Plan
RMRP-22V751-9073.pdf 134.414KB
Owner Notification Letter(Part 577)
RCONL-22V751-1015.pdf 151.481KB
Recall 573 Report- 11/08/2022
RCLRPT-22V751-6629.PDF 219.324KB
Recall Quarterly Report #1, 2022-4
RCLQRT-22V751-6268.PDF 211.132KB
Owner Notification Letter(Part 577)
RCONL-22V751-6666.pdf 216.584KB
Recall Quarterly Report #3, 2023-2
RCLQRT-22V751-8579.PDF 211.235KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V751&docType=RCL
- Durable Ratchet Head: Made from Hardened treated Chrome Vanadium steel alloy (Cr-V) Corrosion-Retardant: Satin Finish. Made in Taiwan
- Easy Storage: A sturdy plastic storage case is included. Non-Slip Grip: Knurled handle
- Easy to Read: High Contrast & Dual Range Scale. Accurate: Pre-Calibrated to ± 4%
- Accessories included: 1/2" Drive 5" long Extension Bar and 1/2" Drive to 3/8" Drive Reducer
- Simple and Reliable: “Click” sound tells the preset torque value is reached. Stop applying force when you hear and feel it.
- PRECISION - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate with traceable serial number.
- DURABLE - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
- LONG-LASTING - Rust & corrosion protection with our unique and newly invented Electro-Black finish treatment.
- PERFORMANCE - Features an easy-to-read, highlighted yellow print dual-range scale. Identify the markings even in low-light conditions.
- COMFORTABLE - Comes with a reversible ratchet head that drives in both directions and measure torque in a clockwise direction.
- ±3% HIGH PRECISION AND COOL APPEARANCE: 1/2 inch drive torque wrench (10-170ft.-lb/13.6-230.5Nm)has a calibration error range of ±3%, high precision, and comes with a corresponding serial number, which is easy to trace the original data, and you can use it with confidence.Hairich torque wrench not only has superior quality but also has a superior appearance. The classic combination of black and red is fashionable and textured, allowing you to enjoy a visual feast during use.
- PREMIUM MATERIAL AND DURABLE: Experience the ultimate durability and antiskid with the torque wrench. The main body of Hairich torque wrench set is made of chrome vanadium steel alloy, which is more strong and more durable. The head of the inch-pound torque wrench adopts a ratchet design with a reversing device to improve work efficiency. The square knurled handle is made of aluminum titanium alloy, which is ergonomic and comfortable to hold for long-time use.
- DUAL SCALE AND QUICK SETTING: Laser Printed by dual-range(ft-lb and Nm). Our professional torque wrench is easy to read and provides direct unit conversion, When the set torque value is reached, the torque wrench will make an audible and felt click to remind you to stop applying force. Pull down the lock knob and hold it until the torque setting is completed. Release the hand, and the lock knob will automatically rebound back to lock the value.
- ERGONOMIC DESIGN AND POWERFUL: Every design of our industrial torque wrench conforms to ergonomic, easy to handle.72-tooth ratchet, 5° ratcheting arc head, a quick-release button for easy loading and unloading, and an aluminum non-slip handle for excellent grip and control. A recent research review that, 72-tooth ratchets are very professional tooth ratchets, you just only rotate 5 degrees to finish it. Not easy to slip and wear, can be used in small spaces, and is more durable and powerful.
- EASY OPERATION AND SAFETY: Thanks to its bidirectional drive ratchet head, our torque wrench can be measured both clockwise and counterclockwise. When the set torque value is reached, a "click" sound will remind you to stop applying force to prevent damage to the item due to excessive torque. Notice: At low Nm settings under 5 Nm the "click" sound can be too light to hear.
- 【High Precision&Quick Reading】: 3/8 torque wrench has high contrast and dual range scale( 5-45 Ft-Lb/6.8-61 Nm),making it clear and easy to read. We have professional torque wrench production technology, and after 20000 tests, the calibration error range of the torque wrench is ± 3%, making it an essential helper for you.
- 【Safe and Reliable Operation】: Equipped with a bidirectional drive ratchet head, torque can be measured clockwise or counterclockwise. When the set torque value is reached, a "click" sound will remind you to stop applying force to prevent damage to the item due to excessive torque.
- 【High Quality and Durable Material】: Made of hardened chromium vanadium steel alloy (Cr-V). At the same time, the bottom buckle tail plug adopts a red anodizing process to improve the product's oxidation resistance during use and enhance surface wear resistance. 72 tooth ratchet head, made of chromium molybdenum steel. High quality materials resist corrosion and are durable.
- 【Quick Torque Setting】: Simple and fast torque setting, pull down the locking knob and hold it down to rotate to the torque you need. Release the hand and the locking knob will automatically rebound to lock the torque value. And the designer referred to the appearance of the flashlight handle and designed a non slip and labor-saving knurled handle, making it more comfortable and easy to hold when using.
- 【Easy to Store and Widely Use】: You will receive the 3/8-inch drive click torque wrench with a sturdy plastic shell storage box, which is very delicate and durable. Torque wrench is suitable nuts and bolts on various occasions, such as bike, motorcycle, car spark, and is the best helper for you🎁. 🔔 And we provide 12 months warranty. If you have any questions, please feel free to contact us.
- 【3Pcs Torque Wrench Set】 The calibration error range is ±3%, each torque wrench has a calibration certificate. The 3-in-1 torque wrench set can meet your different needs. Including 1/4 inch 20-240in.lb, 3/8 inch 5-45ft.lb, 1/2 inch 20-160ft.lb.
- 【Safe & Reliable】 When the 1/2 torque wrench reaches the preset torque value, it makes a clear "click" sound, accompanied by an obvious hand vibration that reminds you no longer to apply force, prevent damage caused. 72-tooth reversible ratchet head, it can be used both clockwise and counterclockwise directions.
- 【Quick Release Button】 This 3/8 torque wrench has a quick release button with which accessories can easily be installed and removed, the accessories can grip and is not easy to fall down. It is more convenient to use. The torque wrench is made of CR-MO with a higher hardness.
- 【Easy to Set】First pull down the locking knob and hold it down and then start setting the desired torque value. Release the hand and the locking knob will automatically rebound to lock the torque value. If you do not use, please set the torque key to the minimal torque value.
- 【Widely Use】The torque wrenches can satisfy you in bicycle, motorcycle, car, truck and wheel screws, wheel nuts and in the device installation, electrical engineering, etc. We provide 12 months warranty. If you have any questions, please feel free to contact us.
- PORTABILITY: Torque wrench 1/2 inch drive has a durable case for portability or storage
- ADDED COMFORT: Bi-material handle for comfort and grip of the 1/2 torque wrench
- HASSLE FREE USE: Locking feature adjusts quick and easily for hassle free use
- QUICK IDENTIFICATION: Scales stamped into housing showing inch and metric torque settings
- Meets or Exceeds ASME Specifications
- 🔧【𝐌𝐢𝐥𝐢𝐭𝐚𝐫𝐲-𝐠𝐫𝐚𝐝𝐞 𝐒𝐭𝐞𝐞𝐥】ETOOLAB torque wrench utilizes military-grade steel as its base material, coupled with professional surface rust protection methods tailored to usage habits. While ensuring user comfort, it enhances product strength, wear resistance, and rust resistance. offers a more comfortable experience and a longer lifespan!
- 👍【𝐄𝐚𝐬𝐲-𝐭𝐨-𝐑𝐞𝐚𝐝】The scale of this 1/2 drive torque wrench is laser-engraved, using a black background with white markings. dinamometrica de 1/2 ensures clear and easy readability of the scale, even in sunlight. With a dual-scale design, users can conveniently read torque values in two different units according to their preferences, without the need for conversion!
- ⚙️【±𝟑% 𝐏𝐫𝐞𝐜𝐢𝐬𝐢𝐨𝐧 & 𝐒𝐢𝐦𝐩𝐥𝐞 𝐋𝐨𝐜𝐤𝐢𝐧𝐠 𝐑𝐢𝐧𝐠】Our torque wrench 1/2 drive meets the high precision standard of ±3% and comes with a traceable serial certificate. You can use it with confidence! Moreover, its graduation ring is tightly locked, with smaller incremental values, ensuring precise and consistent torque output even after multiple uses. This reduces the hassle of frequent adjustments. It is undoubtedly an excellent tool for your work!
- 🔊【𝐋𝐨𝐮𝐝 𝐂𝐥𝐢𝐜𝐤 𝐒𝐨𝐮𝐧𝐝】This torque wrenches has been upgraded to have a louder "Click" sound. We conducted over 25,000 tests to ensure that each product produces a click sound volume of no less than 45dB when the torque value exceeds 34 lbf·ft. When you hear the distinct click sound, it indicates that the preset torque has been reached, signaling you to stop applying force. You no longer need to worry about damaging your mechanical components.
- 💯【𝐔𝐬𝐞𝐫-𝐅𝐫𝐢𝐞𝐧𝐝𝐥𝐲】Our torque wrench set features a 72-tooth dual-directional ratchet head, allowing for easy operation in both clockwise and counterclockwise directions. It is designed with an adjustable locking ring, making it effortless to adjust the preset torque value. Additionally, it includes a quick-release head design, allowing it to replace the wrench head accessories more easily!
- Includes 1-pc. 3/8 in. drive torque wrench; Storage case; Product manual with torque conversion chart
- Wrench emits a click that can be heard and felt when the preset value is reached
- Permanently marked, high-contrast dual-range scale is easy to read, even in low light
- Reversible ratchet head drives in both directions and measures torque in clockwise direction
- Durable all-steel construction has no plastic parts to break or wear out
- Includes 1-pc. 1/4 in. drive micrometer torque wrench (20-200 in.-lb.) with storage case and product manual; 1-pc. 3/8 in. drive micrometer torque wrench (10-80 ft.-lb.) with storage case and product manual; 1-pc. 1/2 in. drive micrometer torque wrench (25-250 ft.-lb.) with storage case and product manual
- Wrenches emit a click that can be heard and felt when the preset value is reached
- Permanently marked, high-contrast dual-range scale is easy to read, even in low light
- Reversible ratchet heads drive in both directions and measure torque in clockwise direction
- Durable all-steel construction has no plastic parts to break or wear out
- 【PRECISION】 - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate . Before shipping, we take 200 times calibration tests to make sure all wrenches performance well .
- 【DURABLE】 - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
- 【 RELIABLE & SAFE】: When small torque wrench set torque value is reached, the wrench will emits slight click sound to remind you to stop applying force to prevent overtorque damage to your items.
- 【LONG-LASTING】 - Rust & corrosion protection with our unique and newly invented Chrome finish treatment.
- 【 DUAL-DIRECTION MEASURES & WIDE USE】: The paddle of the mini torque wrench head can adjust the direction of use at any time,so that the wrench can be used both clockwise and counterclockwise directions. More widely used for Installation equipment, Electrical engineering, bicycle/motorcycle maintenance, Product assembly.With a storage box and an instruction manual.
Last update on 2024-04-11 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Braun Customer Reimbursement Plan Braun will remedy the affected units free of charge by replacing Braun striker pin 97136 with Braun striker pin 97259. Replacement is done by removing the affected pins and inspecting for obstructions in the area where the pin fastens and replacing the pin. Labor reimbursement for the inspection and repair for each ambulance replacement is 30 minutes. The replacement pins will be properly torqued and marked upon installation. Affected Part: Replacement Part: Striker Pin Striker Pin Part Number: 97136 Part Number: 97259 Please contact Braun Industries to arrange inspection and replacement of the affected striker pins in your vehicle(s). The Braun Service contact information is as follows: Phone: 877-344-9990 6:00 a.m. – 4:30 p.m. EDT, Email: braunservice@braunambulances.com
**************************************************************************************************************
IMPORTANT SAFETY RECALL This notice applies to your vehicle(s) VIN, TBD Recall # 22V-751 Braun Recall Notice: 2022-01 September 29, 2022 This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Braun Industries has decided that a safety related defect may exist with certain 2018-2022 Chief XL, Express Plus, Liberty, Super Chief, TLC, and 2018-2021 Signature Series ambulances. The rear door top striker bolts may become loose and separate from the vehicle while it is in motion. As such, these vehicles fail to comply with the requirements of the Federal Motor Vehicle Safety Standard number 206, “Door Locks and Door Retention Components”. In the affected vehicles, loose pins may result in the top of the rear doors not latching or unlatching. This can result in the door not staying closed or not able to be opened during vehicle operation. The door latch may separate from the vehicle while in motion, increasing the risk of a crash. Some pins may not present an issue at initial review, but nevertheless should be inspected and if necessary remedied. You are receiving this notice because Braun records indicate you may have received shipments of affected units. Braun will remedy the affected units free of charge by replacing Braun striker pin 97136 with Braun striker pin 97259. Replacement pins are available as of October 3rd, 2022. Replacement is done by removing the affected pins and inspecting for obstructions in the area where the pin fastens and replacing the pin. Labor reimbursement for the inspection and repair for each ambulance replacement is 30 minutes. The replacement pins will be properly torqued and marked upon installation, free of charge Affected Part: Replacement Part: Striker Pin Striker Pin Part Number: 97136 Part Number: 97259 Please contact Braun Industries to arrange inspection and replacement of the affected striker pins in your vehicle(s). The Braun Service contact information is as follows: Phone: 877-344-9990 6:00 a.m. – 4:30 p.m. EDT, Email: braunservice@braunambulances.com It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by the notification under a sale or lease until the defect or noncompliance is remedied. If Braun Industries is unable to arrange service as described above without charge within a 60 day period upon contacting Braun Industries, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, S.E., Washington, DC 20590 or call toll-free Auto Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153); or go to http://www.safercar.gov. Any lessor who receives a notification of a determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send a copy of such notice to the lessee of a leased motor vehicle, by first-class mail to the most recent lessee known to the lessor. Such notification shall be mailed within ten days of the lessor’s receipt of the notification from the vehicle manufacturer. This requirement applies to both initial and follow-up notifications but does not apply where the manufacturer has notified a lessor’s lessees directly. We apologize in advance for the inconvenience this issue may cause your organization. We will make every effort minimize any inconveniences and to make this as simple as possible for both our Dealers and our Customers. Sincerely, Kim Braun President – U.S. Division
**************************************************************************************************************
Braun Industries, Inc. 1170 Production Drive Van Wert OH 45891 Website: www.braunambulances.com | Phone: 419-232-7020 | Fax: 419-232-7070 IMPORTANT SAFETY RECALL This notice applies to your vehicle(s) VIN, Recall # 22V-751 Braun Recall Notice: 2022-01 September 29, 2022 This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Braun Industries has decided that a safety related defect may exist with certain 2018-2022 Chief XL, Express Plus, Liberty, Super Chief, TLC ambulances and 2018-2021 Signature Series ambulances. The rear door top striker bolts may become loose and separate from the vehicle while it is in motion. As such, these vehicles fail to comply with the requirements of the Federal Motor Vehicle Safety Standard number 206, “Door Locks and Door Retention Components”. In the affected vehicles, loose pins may result in the top of the rear doors not latching or unlatching. This can result in the door not staying closed or not able to be opened during vehicle operation. The door latch may separate from the vehicle while in motion, increasing the risk of a crash. Some pins may not present an issue at initial review, but nevertheless should be inspected and if necessary remedied. You are receiving this notice because Braun records indicate you may have received shipments of affected units. Braun will remedy the affected units free of charge by replacing Braun striker pin 97136 with Braun striker pin 97259. Replacement pins are available as of October 3, 2022. Replacement is done by removing the affected pins and inspecting for obstructions in the area where the pin fastens and replacing the pin. Labor reimbursement for the inspection and repair for each ambulance replacement is 30 minutes. The replacement pins will be properly torqued and marked upon installation, free of charge Affected Part: Replacement Part: Striker Pin Striker Pin Part Number: 97136 Part Number: 97259 Please contact Braun Industries to arrange inspection and replacement of the affected striker pins in your vehicle(s). The Braun Service contact information is as follows: Phone: 877-344-9990 6:00 a.m. – 4:30 p.m. EDT, Email: braunservice@braunambulances.com It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by the notification under a sale or lease until the defect or noncompliance is remedied. If Braun Industries is unable to arrange service as described above without charge within a 60 day period upon contacting Braun Industries, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, S.E., Washington, DC 20590 or call toll-free Auto Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153); or go to http://www.safercar.gov. Braun Industries, Inc. 1170 Production Drive Van Wert OH 45891 Website: www.braunambulances.com | Phone: 419-232-7020 | Fax: 419-232-7070 Any lessor who receives a notification of a determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send a copy of such notice to the lessee of a leased motor vehicle, by first- class mail to the most recent lessee known to the lessor. Such notification shall be mailed within ten days of the lessor’s receipt of the notification from the vehicle manufacturer. This requirement applies to both initial and follow-up notifications but does not apply where the manufacturer has notified a lessor’s lessees directly. We apologize in advance for the inconvenience this issue may cause your organization. We will make every effort minimize any inconveniences and to make this as simple as possible for both our Dealers and our Customers. Sincerely, Kim Braun President – U.S. Division
**************************************************************************************************************
IMPORTANT SAFETY RECALL Braun Recall Notice: TBD September 29, 2022 This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Braun Industries has decided that a safety related defect may exist with some rear door top striker bolts. Braun striker pin part number 97136 may under certain conditions become loose and dislodge from the vehicle while in service. In the affected vehicles, loose pins may result in the top of the rear doors not latching or unlatching. This can result in the door not staying closed or not able to be opened during vehicle operation. The door may not be fully latched increasing the likelihood of the door inadvertently opening in the event of a crash. Some pins may not present an issue at initial review, but nevertheless should be inspected and if necessary remedied. You are receiving this notice because Braun records indicate you may have received shipments of affected units. Braun will remedy the affected units free of charge by replacing Braun striker pin 97136 with Braun striker pin 97259. Replacement pins are available as of October 3rd, 2022. Replacement is done by removing the affected pins and inspecting for obstructions in the area where the pin fastens and replacing the pin. Labor reimbursement for the inspection and repair for each ambulance replacement is 30 minutes. The replacement pins will be properly torqued and marked upon installation. Affected Part: Replacement Part: Striker Pin Striker Pin Part Number: 97136 Part Number: 97259 Please contact Braun Industries to arrange inspection and replacement of the affected striker pins in your vehicle(s). The Braun Service contact information is as follows: Phone: 877-344-9990 6:00 a.m. – 4:30 p.m. EDT, Email: braunservice@braunambulances.com It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by the notification under a sale or lease until the defect or noncompliance is remedied. If Braun Industries is unable to arrange service as described above without charge within a 60 day period upon contacting Braun Industries, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, S.E., Washington, DC 20590 or call toll-free Auto Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153); or go to http://www.safercar.gov. Any lessor who receives a notification of a determination of a safety-related defect or noncompliance pertaining to any leased motor vehicle shall send a copy of such notice to the lessee of a leased motor vehicle, by first-class mail to the most recent lessee known to the lessor. Such notification shall be mailed within ten days of the lessor’s receipt of the notification from the vehicle manufacturer. This requirement applies to both initial and follow-up notifications but does not apply where the manufacturer has notified a lessor’s lessees directly. We apologize in advance for the inconvenience this issue may cause your organization. We will make every effort minimize any inconveniences and to make this as simple as possible for both our Dealers and our Customers. Sincerely, Kim Braun President – U.S. Division
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-751 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Braun Ambulances Submission Date : SEP 30, 2022 NHTSA Recall No. : 22V-751 Manufacturer Recall No. : 22-001 Manufacturer Information : Manufacturer Name : Braun Ambulances Address : 1170 Production Drive Van Wert OH 45891 Company phone : 4192327020 Population : Number of potentially involved : 1,240 Estimated percentage with defect : 25 % Vehicle Information : Vehicle 1 : 2018-2022 Braun Ambulance Chief XL Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 382 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 2 : 2018-2022 Braun Ambulance Chief XL Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 251 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-751 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2018-2022 Braun Ambulance Express Vehicle Type : Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 90 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 4 : 2018-2022 Braun Ambulance Express Plus Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 115 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 5 : 2018-2022 Braun Ambulance Express Plus Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 93 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 6 : 2018-2022 Braun Ambulance Liberty Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 128 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-751 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 7 : 2018-2022 Braun Ambulance Liberty Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 10 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 8 : 2018-2021 Braun Ambulance Signature Series Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 8 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 9 : 2018-2022 Braun Ambulance Signature Series Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 27 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 10 : 2018-2022 Braun Ambulance Super Chief Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 133 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-751 Page 4 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 11 : 2018-2022 Braun Ambulance TLC Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 3 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : Rear door top striker bolts are coming lose and sometimes dislodging while the vehicle is in service. FMVSS 1 : 206 – Door locks and door retention components FMVSS 2 : NR Description of the Safety Risk : Door may not latch or unlatch, which can result in the door not being able to stay close or open during vehicle operation. Door may not be fully latched, which will increase the likelyhood of the door inadvertanly opening in the even of a crash. Description of the Cause : 1. Excessive gap between reinforcement plate and inside of top header allows for area to permanently deform, removing tension on the fastener and allowing it to be loose. 2. Striker bolt not properly torqued. 3. Nut plate hung up on inside radius of top header when torqued, which will loosen from vibration and impact. 4. Body filler between nut plate and reinforcement plate. 5. Weld between nut plate and reinforcement plate. Lack of thread engagement due to excessive use of shims. Identification of Any Warning that can Occur : Striker pin may become loose or dislodge. Involved Components : Component Name 1 : Striker door latch bolt Component Description : Striker door latch bolt – upper rear Component Part Number : Internal Braun part – 97136 Part 573 Safety Recall Report 22V-751 Page 5 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : NR Address : NR NR Country : NR Chronology : May 2022 – Customer report of loose pins/pins dislodging in the field. Problem was corrected under warranty claim July 2022 – Customer report of loose pins/pins dislodging in the field. Problem was corrected under warranty claim July 2022 – transitioned to new striker pin 97259 to replace 97136, August – September 2022 – evaluated failure modes of the 91736, improved install process of new striker. Septemebr 2022 – arrived at decision to address field failures via recall and inspection/replacement of any of the 97136 strikers in the field. Description of Remedy : Description of Remedy Program : Via NHTSA Recall replace 97136 striker bolt with 97259. Visually inspect all other upper rear door nut plate/striker bolt assemblies to insure they are seated correctly and re-torque all other striker bolts. Braun will remedy the affected units free of charge by replacing Braun striker pin 97136 with Braun striker pin 97259. Replacement pins are available as of October 3rd, 2022. Replacement is done by removing the affected pins and inspecting for obstructions in the area where the pin fastens and replacing the pin. Labor reimbursement for the inspection and repair for each ambulance replacement is 30 minutes. The replacement pins will be properly torqued and marked upon installation. How Remedy Component Differs from Recalled Component : Remedy component has a longer threaded portion than that of part 97136. 97259 will protrude through the mounting block. Identify How/When Recall Condition was Corrected in Production : New striker pin 97259 was implemented into production 7/1/22 replacing 97136. Recall Schedule : Description of Recall Schedule : Letters will be sent to our dealer network and direct customer of the the Part 573 Safety Recall Report 22V-751 Page 6 The information contained in this report was submitted pursuant to 49 CFR §573 vehicle. This will start/go through the dates listed for both dealer and customer/owner notification. Planned Dealer Notification Date : OCT 10, 2022 – OCT 14, 2022 Planned Owner Notification Date : OCT 17, 2022 – NOV 04, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-751 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Braun Ambulances Submission Date : NOV 08, 2022 NHTSA Recall No. : 22V-751 Manufacturer Recall No. : 22-001 Manufacturer Information : Manufacturer Name : Braun Ambulances Address : 1170 Production Drive Van Wert OH 45891 Company phone : 4192327020 Population : Number of potentially involved : 1,240 Estimated percentage with defect : 25 % Vehicle Information : Vehicle 1 : 2018-2022 Braun Ambulance Chief XL Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 382 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 2 : 2018-2022 Braun Ambulance Chief XL Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 251 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-751 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2018-2022 Braun Ambulance Express Vehicle Type : Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 90 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 4 : 2018-2022 Braun Ambulance Express Plus Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 115 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 5 : 2018-2022 Braun Ambulance Express Plus Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 93 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 6 : 2018-2022 Braun Ambulance Liberty Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 128 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-751 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 7 : 2018-2022 Braun Ambulance Liberty Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 10 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 8 : 2018-2021 Braun Ambulance Signature Series Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 8 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 9 : 2018-2022 Braun Ambulance Signature Series Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : DIESEL Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 27 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 10 : 2018-2022 Braun Ambulance Super Chief Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 133 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 22V-751 Page 4 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 11 : 2018-2022 Braun Ambulance TLC Vehicle Type : BUSES, MEDIUM & HEAVY VEHICLES Body Style : ALL Power Train : GAS Descriptive Information : Recall population starts and ends 1 month prior and post use of the door striker pin covered in this recall. Braun internal part code 97136 is the specific part in this recall. Total of 3 vehicles produced. 25% estimated to have this problem. All will need to be inspected. Production Dates : JUN 01, 2018 – AUG 01, 2022 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : Rear door top striker bolts are coming lose and sometimes dislodging while the vehicle is in service. FMVSS 1 : 206 – Door locks and door retention components FMVSS 2 : NR Description of the Safety Risk : Door may not latch or unlatch, which can result in the door not being able to stay close or open during vehicle operation. Door may not be fully latched, which will increase the likelyhood of the door inadvertanly opening in the even of a crash. Description of the Cause : 1. Excessive gap between reinforcement plate and inside of top header allows for area to permanently deform, removing tension on the fastener and allowing it to be loose. 2. Striker bolt not properly torqued. 3. Nut plate hung up on inside radius of top header when torqued, which will loosen from vibration and impact. 4. Body filler between nut plate and reinforcement plate. 5. Weld between nut plate and reinforcement plate. Lack of thread engagement due to excessive use of shims. Identification of Any Warning that can Occur : Striker pin may become loose or dislodge. Involved Components : Component Name 1 : Striker door latch bolt Component Description : Striker door latch bolt – upper rear Component Part Number : Internal Braun part – 97136 Part 573 Safety Recall Report 22V-751 Page 5 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : NR Address : NR NR Country : NR Chronology : May 2022 – Customer report of loose pins/pins dislodging in the field. Problem was corrected under warranty claim July 2022 – Customer report of loose pins/pins dislodging in the field. Problem was corrected under warranty claim July 2022 – transitioned to new striker pin 97259 to replace 97136, August – September 2022 – evaluated failure modes of the 91736, improved install process of new striker. Septemebr 2022 – arrived at decision to address field failures via recall and inspection/replacement of any of the 97136 strikers in the field. Description of Remedy : Description of Remedy Program : Via NHTSA Recall replace 97136 striker bolt with 97259. Visually inspect all other upper rear door nut plate/striker bolt assemblies to insure they are seated correctly and re-torque all other striker bolts. Braun will remedy the affected units free of charge by replacing Braun striker pin 97136 with Braun striker pin 97259. Replacement pins are available as of October 3rd, 2022. Replacement is done by removing the affected pins and inspecting for obstructions in the area where the pin fastens and replacing the pin. Labor reimbursement for the inspection and repair for each ambulance replacement is 30 minutes. The replacement pins will be properly torqued and marked upon installation. How Remedy Component Differs from Recalled Component : Remedy component has a longer threaded portion than that of part 97136. 97259 will protrude through the mounting block. Identify How/When Recall Condition was Corrected in Production : New striker pin 97259 was implemented into production 7/1/22 replacing 97136. Recall Schedule : Description of Recall Schedule : Letters will be sent to our dealer network and direct customer of the the Part 573 Safety Recall Report 22V-751 Page 6 The information contained in this report was submitted pursuant to 49 CFR §573 vehicle. This will start/go through the dates listed for both dealer and customer/owner notification. All customer letters were mailed on Monday, 11/7/22. Planned Dealer Notification Date : OCT 10, 2022 – OCT 14, 2022 Planned Owner Notification Date : OCT 17, 2022 – NOV 07, 2022 * NR – Not Reported
SEOCONTENT-END