Hub May Separate from Axle Wheel End – 2022 Oliver Legacy Elite II Travel Trailers

“This site contains affiliate links for which OEMDTC may be compensated”

July 1, 2022 NHTSA CAMPAIGN NUMBER: 22V474000

Hub May Separate from Axle Wheel End

Hub separation from the wheel end may cause loss of vehicle control, increasing the risk of a crash.

 

NHTSA Campaign Number: 22V474000

Manufacturer Oliver Travel Trailers, INC.

Components POWER TRAIN

Potential Number of Units Affected 13

 

Summary

Oliver Travel Trailers, Inc. (Oliver) is recalling certain 2022 Legacy Elite II travel trailers. The 42mm cartridge bearing washer within the hub assembly may crack, causing the hub to separate from the axle wheel end.

 

Remedy

Dealers will replace the 42mm cartridge bearing washer, free of charge. Owner notification letters were mailed in July 29, 2022. Owners may contact Oliver customer service at 1-866-205-2621.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 


Oliver Travel Trailer’s has decided that a defect which relates to motor vehicle safety exists in certain 2022 Legacy Elite II travel trailers manufactured between April 1, 2022 and June 22, 2022 equipped with certain Dexter axles.

The issue is some axle 42mm cartridge bearing washers within the hub assembly may crack, causing the hub to separate from the axle wheel end.

A hub separation from the wheel end may cause loss of vehicle control, increasing the risk of a crash.

Your Legacy Elite II was manufactured within the affected period using this component and is to be inspected to ensure the axle is not within the recall population as identified by serial number. Remedy will be by replacement of the 42mm cartridge bearing washer, free of charge. The replacement washers will be sent with instructions to complete the installation by a qualified RV technician. The replacement should take approximately two hours to complete.

Please contact Dexter Warranty for service locations and to schedule an appointment for repair as soon as possible.

If you have questions or concerns about this recall, please contact
Dexter Warranty Department as follows:

Email: Warranty@dexteraxle.com
Phone: 574-413-9066

Dexter will be able to assist in identifying service center in your locality if you require help. Service Center’s should be able to bill Dexter for the inspection, if you encounter any problems with that, please contact direct.

Oliver Travel Trailers may be contacted for assistance as follows:

Email: olivertraveltrailers.com
Phone: 1-866-205-2621

 


Chronology :

6/22/22 Kyle Bobo, OTT Purchasing was in communication with Sean Cantzler, Dexter Warranty Manager upon a purchasing agent reporting an axle delivery delay due to a safety recall concern.

6/23/22 Oliver Travel Trailers placed all 52029455 axles, sub structures, and work in process on containment to verify suspect serial numbers.

6/23/22 Oliver Travel Trailers and Oliver Sales and Service inspected Elite II model units to identify serial numbers within the Dexter suspect serial range.

6/27-6/30/22 Dexter provide technicians to support replacing washers in axles with the serial range at OTT and OTTSI locations.

 


1 Affected Product

Vehicle

MAKE MODEL YEAR
OLIVER TRAVEL TRAILERS LEGACY ELITE II 2022

 


9 Associated Documents

Recall 573 Report

RCLRPT-22V474-9823.PDF 215.939KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [210.88 KB]

 


Recall Acknowledgement

RCAK-22V474-8850.pdf 646.076KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [630.93 KB]

 


Recall 573 Report – 7/29/2022

RCLRPT-22V474-3394.PDF 215.941KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [210.88 KB]

 


Recall 573 Report – 8/8/2022

RCLRPT-22V474-9554.PDF 215.998KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [210.94 KB]

 


Recall 573 Report – 10/3/2022

RCLRPT-22V474-6374.PDF 215.998KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [210.94 KB]

 


ISSUED Owner Notification Letter(Part 577)

RCONL-22V474-2722.pdf 134.113KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [130.97 KB]

 


Recall Quarterly Report #2, 2022-4

RCLQRT-22V474-5631.PDF 211.219KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.27 KB]

 


Recall Quarterly Report #1, 2022-3

RCLQRT-22V474-9546.PDF 211.219KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.27 KB]

 


Recall Quarterly Report #3, 2023-1

RCLQRT-22V474-5715.PDF 211.308KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.36 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V474&docType=RCL

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
Bestseller No. 1
The Trailer Parts Outlet - 3.5k TK Trailer Axle - 3500 lb Idler 5 Lug - Dexter Compatible, 61/46 Hubface/Spring Center - (4'0) Frame Width / 5x4.5 Bolt Pattern
  • Specs: 3,500 lbs Idler Trailer Axle (Capacity 3.5K), 5 Lug, Tube: 2 3/8"
  • High Strength Straight Steel Axle Tube
  • Axle comes fully assembled, so all you'll have to do is attach the springs, the U-bolt kits, and the tire and wheel assemblies.
  • Underslung - Spring seats are welded to the bottom of the axle, which allows for a lower ride height.
  • Trailer Axle Design for use on Light Duty Trailers
Bestseller No. 2
The Trailer Parts Outlet - 2k TK Trailer Axle - 2000 lb Idler, 61/46 Hubface/Spring Center - (4'0) Frame Width / 4x4 Bolt Pattern
  • EZ Lube Design Removable rubber plug on the hub cap with easy access to a grease-able zerk fitting Grease your axle without pulling off your whole entire hub
  • Internal Wiring System To ensure seamless design Protect brake wires from wear and tear
  • High Strength Straight Steel Axle Tube Construction to ensure Even Tire Wear A better highway experience
  • Underslung - Axle is welded with spring seats on the bottom Allows for lower ride height For optimal usage, use with double eye springs
Bestseller No. 3
LCI Lippert 3,500LB Straight Idler Trailer Axle 72HF 58SC
  • 72" from Hubface to Hubface and 58" Spring Center to Spring Center.
  • Springs are 25 1/4" long and 1 3/4" wide
  • 4 Leaf Springs
  • 2-3/8" Main Tube
  • 5 Lug with a 4 1/2" bolt pattern. 1/2 lug studs.
Bestseller No. 4
The Trailer Parts Outlet - 2k TK Trailer Axle - 2000 lb Idler, 71/58 Hubface/Spring Center - (5'0) Frame Width / 5x4.5 Bolt Pattern
  • Capacity: 2000 lbs, Tube:1-3/4 | 5x4.5 Bolt Pattern
  • EZ Lube Design: Removable rubber plug on the hub cap with easy access to a grease-able zerk fitting. Grease your axle without pulling off your whole entire hub.
  • Internal Wiring System: To ensure seamless design and protect brake wires from wear and tear.
  • High Strength Straight Steel Axle Tube Construction: To ensure even tire wear and a better highway experience.
  • Underslung - Axle is welded with spring seats on the bottom: Allows for lower ride height. For optimal usage, use with double eye springs.
Bestseller No. 5
TK Axles + 3.5k-3500 Lb Capacity Trailer Idler Straight Axle - 5 on 4.5 Bolt Pattern (Assembled Idler Axle, 73" Hubface-58 Spring Center(5'0Frame))
  • Completely DEXTER Compatible; Half the Price
  • Capacity: 3500 lbs
  • Option to Add Spring and Ubolt Kits Needed to Hang Your Axle
  • Tube: 2 3/8"; EZ Lube Design
  • Underslung: Axle is welded with Spring Seats on the Bottom
Bestseller No. 6
The Trailer Parts Outlet - 3.5k TK Trailer Axle - (3500 lb Beam Only), 95/80 Hubface/Spring Center - (6'10) Frame Width for Utility/ATV/Boat/Cargo
  • Versatile Design - Compatible for use on Medium Duty Trailers Utility, Boat, Car Haulers, ATV, Lawn & Landscape, Flatbed, Livestock, Cargo, Enclosed, RV Trailers, Dump, Lowboy, Flatbed Trailers and more
  • EZ Lube design for effortless maintenance - grease your axle without removing the whole hub assembly
  • Underslung - Our trailer axle beam is welded with spring seats on the bottom Allows for lower ride height, for optimal usage, use with double eye springs
  • High-Strength Construction - Made with straight steel axle tube to ensure even tire wear and a better highway experience
  • Easy Installation - Simply pair with double eye springs for optimal usage and get your trailer back on the road in no time
Bestseller No. 7
The Trailer Parts Outlet - 3.5k TK Trailer Axle - 3500 lb Idler 5 Lug - Dexter Compatible, 89/74 Hubface/Spring Center - (6'4) Frame Width / 5x5 Bolt Pattern
  • Specs: 3,500 lbs Idler Trailer Axle (Capacity 3.5K), 5 Lug, Tube: 2 3/8"
  • High Strength Straight Steel Axle Tube
  • Axle comes fully assembled, so all you'll have to do is attach the springs, the U-bolt kits, and the tire and wheel assemblies.
  • Underslung - Spring seats are welded to the bottom of the axle, which allows for a lower ride height.
  • Trailer Axle Design for use on Light Duty Trailers
Bestseller No. 8
RIGID HITCH INCORPORATED 2,000 lb. Torsional Stub Axles with 5-Bolt on 4-1/2 Inch Hubs (TSA-20150)
  • 2,000 lbs capacity
  • Stub axles can be bolted (hardware not included) or welded to trailer frame
  • 45 degree downward starting angle
  • Perfect item to easily build your own custom motorcycle trailer
  • Read product description below for more detailed information.
Bestseller No. 9
The Trailer Parts Outlet - 6k TK Trailer Axle - 6000 lb Idler 6 Lug, 85/70 Hubface/Spring Center - (6'0) Frame Width / 6x5.5 Bolt Pattern
  • 6,000 lbs TK Trailer Axle (6K Capacity), Tube: 3", Bolt Pattern: 6x5.5
  • Axles come fully assembled - Packed with High-Temp Axle Grease
  • High Strength Steel Axle Tube Construction to ensure
  • Designed for use on Light Duty Trailers
Bestseller No. 10
LCI Lippert 3,500LB Straight Idler Trailer Axle 60HF 48SC
  • 60" from Hubface to Hubface and 48" Spring Center to Spring Center.
  • Springs are 25 1/4" long and 1 3/4" wide.
  • 4 Leaf Springs
  • 2-3/8" Main Tube
  • 5 Lug with a 4 1/2" bolt pattern. 1/2 lug studs.

Last update on 2024-04-12 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

 


Leave a Comment

Share to...