GROUP

NUMBER

CAMPAIGN

Technical Service Bulletin
SUBJECT:

25-01-043H

DATE

MODEL(S)

AUGUST 2025

KONA (SX2)

BDC SOFTWARE UPDATE
(SERVICE CAMPAIGN TCW)

 IMPORTANT
Dealers must perform this service campaign on all affected vehicles prior to customer retail delivery
and whenever an affected vehicle is in the shop for any maintenance or repair.
Access the “Vehicle Information” screen via WebDCS to identify open campaigns.
Description: Some Kona (SX2) vehicles may experience battery drain due to faulty logic keeping the
taillights illuminated while the vehicle is parked and turned off. Follow the procedures outlined in this
TSB to update the Body Domain Controller (BDC) to the latest software.
Applicable Vehicles (Certain):
• 2024-2025MY Kona (SX2) vehicles produced from 04/27/2024 – 04/11/2025
SST Information:
Tool Name

Tool Number

VCI 3

G0VHNNN06

Figure

Ordering Information

Website:
https://hyundaiessentialtools.com/
Email:
[email protected]
Phone: 1-855-763-9199
Hours: 7 AM – 7 PM CST

VCI 2

G1XDDMN001

Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors, Technicians, Body Shop Manager, Fleet Repair

BDC OTA SOFTWARE UPDATE (SERVICE CAMPAIGN TCW)

SUBJECT:

GDS Information:
System

Event Number

Description

BDC-BCM

1222

SX2/SX2 EV BDC LOGIC IMPROVEMENT

(*or use a later available event as listed in the GDS BDC-BCM update screen if one is available.)
NOTE 1: This software update is subject to an OTA (Over-the-Air) option and may be completed by
customers with active Bluelink subscriptions.

Warranty Information:
Model

Op. Code

Operation

Op.
Time

Causal Part

Nature
Code

Cause
Code

Kona (SX2)

50D057R0

BDC Software
Update

0.6 M/H

95400-BE100

W11

ZZ3

NOTE 1: Submit claim on Claim Entry Screen as “Campaign” type.
NOTE 2: If a part is found in need of replacement while performing this campaign and the affected
part is still under warranty, submit a separate claim using the same repair order. If the affected part is
out of warranty, submit a Prior Approval request for goodwill consideration prior to performing the
work.
NOTE 3: Op times include VIN, Mileage, and photo capture of the “ECU update complete” screen as
outlined in the Digital Documentation Policy.

ROM ID Information:
ROM ID

Model

Event
Number

System

ECU
Part Number

Old

New

Kona (SX2)

1222

BDC-BCM

95400-BE100
95400-BE110

3.00
3.10

3.20

TSB #: 25-01-043H

Page 2 of 7
SUBJECT:

SUBJECT:

BDC OTA SOFTWARE UPDATE (SERVICE CAMPAIGN TCW)

Service Procedure:

DIGITAL DOCUMENTATION
This TSB includes Repair validation photos. Refer to the latest Warranty Digital Documentation
Policy for requirements.

NOTICE
You must initially perform the GDS ECU update in Auto Mode.
• If the ECU update starts but then fails in Auto Mode, perform the update in Manual Mode
to recover.

NOTICE
Ensure the vehicle’s battery charge is above 11.0V and the tablet’s battery charge is above 30%
before performing a software update to avoid the update from failing.

i

Information

•

Turn off all lamps (do NOT leave head lamp switch in auto mode) and all accessories.

•

Perform update with the ignition switch in the ON position.

•

Do NOT disconnect any cables connected to the vehicle or scan tool during update.

•

Do NOT start the engine during update.

•

Do NOT turn off the ignition switch during update.

TSB #: 25-01-043H

Page 3 of 7
SUBJECT:

BDC OTA SOFTWARE UPDATE (SERVICE CAMPAIGN TCW)

SUBJECT:

ECU Update Procedure
1.

Perform the ECU update in Auto Mode.
After selecting Auto Mode, please scan the
control unit's ROM ID.

i

Information

Refer to TSB # 24-GI-012H, “ECU
Update Procedure for Tablet-Based
GDS-Smart”, for additional information.

2.

Select the BDC-BCM system to scan the
vehicle’s current ROM ID and then begin the
update.

NOTICE
Check the current ROM ID version and
compare it to the ROM ID Information
table before attempting to perform the
software update.

NOTICE
If the update fails, please remove the
power connector from the in-cabin fuse
box or disconnect the negative (-) battery
terminal for at least 5 seconds and
reassemble it to retry the update.

TSB #: 25-01-043H

Page 4 of 7
SUBJECT:

BDC OTA SOFTWARE UPDATE (SERVICE CAMPAIGN TCW)

SUBJECT:

3.

After the ECU update process shows 100%
complete, follow the prompts on the screen to
cycle the ignition for the prescribed time.

i

Information

Use the Refresh button to reset the
timer.

4,

DIGITAL
DOCUMENTATION

Take a screenshot of the ECU update
complete screen using your tablet and
upload to STUI.

TSB #: 25-01-043H

Page 5 of 7
SUBJECT:

SUBJECT:

5.

BDC OTA SOFTWARE UPDATE (SERVICE CAMPAIGN TCW)

OTA initialization (A) should perform
automatically:
• If OTA initialization performs
automatically, then proceed with the
service procedure.
• If the OTA initialization process fails,
complete it manually under:
S/W Management > CCU_CCNF Central Communication Unit (CCNF)
> OTA Initialization (B).

A

Follow the instructions on the screen.

B

TSB #: 25-01-043H

Page 6 of 7
SUBJECT:

BDC OTA SOFTWARE UPDATE (SERVICE CAMPAIGN TCW)

SUBJECT:

6.

Perform an All Systems Fault Code search
and erase DTC history that had incidentally
occurred from the ECU update.

7.

Disconnect the power connector (C) of the incabin fuse box, wait at least 5 seconds, then
reconnect it.

i

Information

C

Alternatively, disconnect the negative (–)
12V battery terminal, wait 5 seconds, then
reconnect it.

8.

Start the engine or place in Ready mode to
confirm proper operation of the vehicle.

NOTICE
If either ECU update fails in Auto Mode, perform the update in Manual Mode using the
password(s) below.
Manual Mode Password:
Event Number

ECU Menu

Password

1222

SX2 BDC 95400-BE100/10,BF100/10

5400

TSB #: 25-01-043H

Page 7 of 7
SUBJECT: