•

Position in Rest of World (RoW) = ... -RoW

Also observe the body variants (Base 9YA / Coupé 9YB) when positioning the front
camera!

Jun 24, 2025
Page 6 of 25

Tequipment

Installation and Conversion Instructions
2.1.3

Cayenne (9YA)
1/23

ENU

9163

9

Copy dimensions X– and Z– according to country / market and body variant on
outside of windshield.
– Base (9YA):
Dimensions

Rest of World (RoW)

Dimension X (roof edge – lower edge of
front camera base):

Length 280 mm/ 11.02 in

Dimension Z (Inner edge of rain sensor
outline (circle) – inner edge of front
camera base):

Length 35 mm/ 1.38 in

– Coupé (9YB):
Dimensions

Rest of World (RoW)

Dimension X:

Length 305 mm/ 12 in

Dimension Z:

Length 35 mm/ 1.38 in

Information
Observe the following points during positioning/alignment:

2.2

•

Sufficient distance between front camera and interior mirror base: at least 5
mm/ 0.2 in.

•

Get another person standing in front of the vehicle to check and confirm the horizontal alignment of the camera with the PORSCHE logo!

2.1.4

Þ Figure 7 -4-) in the vehicle at the
Position front camera with retainer plate (⇒
Þ Figure 7 -Arrowsmarking on the windshield. ⇒

2.1.5

Get another person to trace and shade in the outline of the retainer plate on the
outside of the windshield using a marking pencil / chalk.

2.1.6

Clean the inside of the windshield in the bonding area for the retainer plate (shaded
area) to remove any dust and grease.

Install front camera (dashcam) on the windshield
NOTICE

Adhesive films not prepared/installed correctly
•

Damage to adhesive films

•

Inadequate adhesion of adhesive films

Þ
⇒

Carefully clean the areas on which you intend to stick the film to ensure that all traces of oil,
grease and silicone are completely removed.

Þ
⇒

Do not touch the bonding surfaces.

Tequipment

Jun 24, 2025
Page 7 of 25

9

Cayenne (9YA)
9163

ENU

Þ
⇒

Installation and Conversion Instructions

1/23

Object (adhesive film, vehicle, etc.) and ambient temperature: Minimum temperature 15°C / 59
°F.
2.2.1

Pull 3M privacy film off the backing
Þ Figure 8 -Asheet. ⇒
1
2
3

– 3M privacy film
– Marked bonding surface
– Interior mirror base

2.2.2

Position 3M privacy film on marked
Þ
bonding surface on windshield. ⇒
Figure 8 -B-

2.2.3

Carefully affix 3M privacy film using
a plastic squeegee, starting from the
center and moving towards the edge.

Figure 8
2.2.4

Pull protective film off the front
Þ Figure 9
camera retainer plate (⇒
-top-).
1
2
3
4

–
–
–
–

Protective film
Front camera
3M privacy film
Interior mirror

Information
Observe the following points during
positioning/alignment:
•

Sufficient distance between
front camera and interior mirror
base: at least 5 mm/ 0.2 in.

•

Get another person standing in
front of the vehicle to check
and confirm the horizontal
alignment of the camera with the PORSCHE logo!

Figure 9

Align front camera with retainer plate symmetrically with respect to the 3M privacy
Þ Figure 9 -bottom-).
film (⇒

Jun 24, 2025
Page 8 of 25

Tequipment

Installation and Conversion Instructions
2.2.5

Cayenne (9YA)
1/23

ENU

9163

9

Press front camera with retainer plate firmly onto the 3M privacy film on the windshield.

Information
Route electric wire harness along existing wiring, if installed.
Make sure that safety components (airbags, etc.) are still working correctly!
2.3

Route and connect electric wiring harness
– Line routing - Base (9YA):⇒ Figure 10 (9YA)
1
2

– Front camera
– Front camera mounting plate with
wiring harness
3
– Power supply pre-fitting
4
– Rear camera pre-fitting
Blue – Camera position for Germany (D)
green – Camera position for Rest of World
(RoW)
•

Front camera → left (seen in direction of
travel) RoW: below rear-view mirror cover

Figure 10 (9YA)

Tequipment

Jun 24, 2025
Page 9 of 25

9

Cayenne (9YA)
9163

ENU

Installation and Conversion Instructions

1/23

– Line routing - Coupé (9YB):⇒ Figure 11
(9YB)
1
2

– Front camera
– Front camera mounting plate with
wiring harness
3
– Power supply pre-fitting
4
– Rear camera pre-fitting
Blue – Camera position for Germany (D)
green – Camera position for Rest of World
(RoW)
•

Front camera → left (seen in direction of
travel) RoW: below rear-view mirror cover

Figure 11 (9YB)
2.3.1

Expose power supply pre-fitting
plug connections and rear camera
pre-fitting at the roof console.
1
2
3

– Power supply pre-fitting
– Rear camera pre-fitting
– Rearview mirror (interior)

Remove retaining clip with power
Þ
supply plug from roof lining frame. ⇒
Figure 12 -1Remove rear camera pre-fitting plug
Þ Figure 12 -2from holder. ⇒

Jun 24, 2025
Page 10 of 25

2.3.2

Route front camera (dashcam) wiring
harness left of the interior mirror to
the roof console. Observe vehicle &
country variants.

2.3.3

Figure 12
Wrap front camera wiring harness
with switch and coupling with fabric tape before routing it.

Tequipment

Installation and Conversion Instructions
2.3.4

2
3
4

ENU

9163

9

– Power supply plug
connection retaining clip
– Rear camera plug
connection
– Front camera wiring
harness
– Front camera

2.3.5

Route rear camera link along existing
lines to rear camera pre-fitting (roof
console at the right in direction of travel).

2.3.6

Þ Figure 13 -2Connect rear camera pre-fitting plug and re-fit it in the holder. ⇒

2.3.7

Secure routed wire harness to existing lines / components in the vehicle with
tie-wraps without tensile stress and so that no chafing occurs.

Figure 13

ONLY for RoW vehicles: Make groove for
mounting plate wiring harness in rear-view
mirror (interior ⇒ Figure 14) cover.
1
2
Æ
∅

2.5

1/23

Plug in power supply pre-fitting (roof
console at the left) and reattach
retaining clip to roof lining frame.
1

2.4

Cayenne (9YA)

– Rear-view mirror (interior) cover
– Groove marking
– Groove diameter approx. 5 mm

2.4.1

Install rear-view mirror cover provisionally on the roof console.

2.4.2

Check front camera wiring harness
routing from mounting plate to roof
and mark position of outer wiring
Þ Figure 14 -2harness on antenna cover. ⇒

Figure 14

2.4.3

Remove (interior) rear-view mirror cover from roof console and check that there is a
locking lug / mounting bar near the marking on the inside.

2.4.4

Make a groove (approx. 5 mm) on the side of the locking lug / mounting bar for
mounting plate wiring harness.

Install rear-view mirror cover (interior). ⇒ Workshop Manual '682719 Remove and install
interior rearview mirror'

Tequipment

Jun 24, 2025
Page 11 of 25

9

Cayenne (9YA)
9163

ENU

3

Installation and Conversion Instructions

1/23
Installing rear camera

Overview of installation position of rear camera:
⇒ Figure 15
1
2
3
3.1

– Installation position of rear camera
– Electric wire harness
– Rear camera pre-fitting
Positioning rear camera on rear window.
3.1.1

Transfer dimensions to rear window
according to body variant.
Figure 15
– Base (9YA):⇒ Position of rear
camera base (9YA)
1
2
3
X
Z

– Corner of roof spoiler
– Corner of tailgate/lower
edge of rear window
– Outline of rear camera base
– 298 mm
– 212 mm

Position of rear camera base (9YA)

Jun 24, 2025