CUSTOMER SATISFACTION CAMPAIGN
MODEL G ICE MAKER WATER LINE LEAK
CSC: CSC-2401 Model G Ice Maker Water Line Leak
PRODUCT: Model G

REVISION: REV-B

DATE: June 3, 2025

LABOR RATE:

1.5 hours

Applies to:
This document refers to Brinkley G-series 5th Wheels with VIN’s as listed below:

Affected Vehicle Identification Numbers
From
0006
0012
0078
0086

To
0010
0076
0084
0089
0091

Condition: Brinkley RV has determined that on certain Model G Fifth Wheels, under certain conditions, the
water supply line to the ice maker may pull loose, or out, creating a water leak.
Correction: As a proactive measure, and to protect our customer’s investment, Brinkley RV will, at no charge to
the customer, pay to perform this procedure on VIN specific Model G fifth wheels listed above.

Ice Maker Waterline Replacement Kit K108113
Part Number

Description

Qty

101916

WAGO 3-LEVER CONNECTOR

2

109859

ICE MAKER WATER LINE

1

101006

BLACK SILICONE

1

101682

15” ZIP TIES

7

Required Tools:
1. Crescent wrenches - two (2)
2. Screw gun with #2 square
drive bit and 3/8” socket
3. Wire strippers
4. Razor knife (not shown)

1

2

3

Work Instructions: CSC-2401 Model G Ice Maker Water Line Leak
Revision Level: REV-B
Product: Model G
Page 1 of 8

NO ADVANCED CONTACT OR PRIOR AUTHORIZATION REQUIRED
CLAIM REIMBURSEMENT PROCESSING:
All reimbursement requests with completed work orders, including any freight expenses, should be submitted via
a claim in the Brinkley RV Dealer Portal. If you do not have access to our Portal, a claim can be emailed to [email protected].
REQUIRED INFORMATION FOR IMMEDIATE REIMBURSEMENT PROCESSING INCLUDES:
1.
2.
3.
4.
5.
6.
7.
8.

The full 17 digit VIN;
The Retail Name if retail sold;
Dealer Name;
Dealer Address;
Dealer Phone Number;
Dealer Hourly Labor Rate;
Work Order detailing the work performed and labor time, and
Photo of completed repairs.

Reimbursement checks for claims submitted with all requested information are issued weekly.
SAFETY:
This document provides general instructions. Many variables can change the circumstances of any procedure,
i.e., the degree of difficulty involved in the service operation and the ability level of the individual performing the
operation. This document cannot begin to plot out procedures for every possibility, but will provide the general
instructions for effectively installing, removing or servicing the system. In the event the skill level required is
too advanced or the procedure too difficult, a certified technician should be consulted before performing the
necessary operation. Failure to correctly install, remove or service the system may result in voiding the warranty,
inflicting injury or even causing death.

WARNING
The “WARNING” symbol above is a sign that a procedure has a safety risk involved and may cause death, serious
personal injury, severe product and/or property damage if not performed safely and within the parameters set
forth in this document.

CAUTION
The “CAUTION” symbol above is a sign that a procedure has a safety risk involved and may cause personal injury,
product and/or property damage if not performed safely and within the parameters set forth in this document.

Work Instructions: CSC-2401 Model G Ice Maker Water Line Leak
Revision Level: REV-B
Product: Model G
Page 2 of 8

CAUTION
Always wear Personal Protection Equipment (PPE), such as eye protection, ear protection, gloves and possibly
a full face shield depending on the nature of the task to be performed.

+ NOTICE

Use caution not to damage the underbelly material and structure when removing and installing.
1. READ AND UNDERSTAND ALL INSTRUCTIONS PRIOR TO BEGINNING WORK.
2. Fully extend the off-door side kitchen slide-out (Figure 1).

KITCHEN SLIDEOUT EXTENDED

Figure 1

3. Locate and remove sewer hose storage tube (Figure 2a and Figure 2b).

Figure 2a

Figure 2b
Work Instructions: CSC-2401 Model G Ice Maker Water Line Leak
Revision Level: REV-B
Product: Model G
Page 3 of 8

+ NOTICE
DO NOT cut the underbelly material. Brinkley RV
does not approve of, or cover cost of, cutting of the
underbelly material.
4. Drain fresh water tanks. Thereafter, remove
the fresh water tank drain valves by unscrewing
them from the from the tanks (Figure 3).

ICE MAKER
WATER LINE
REMOVE
SILICONE

WATER LINE
HEATER WIRING

UNDERBELLY

Figure 4b

Figure 3

5. Pull a section of underbelly down to expose
the holding tanks, water lines and ice maker
water line heater wiring (Figure 4a, Figure 4b
and Figure 4c).
WATER LINE
HEATER WIRING

FRONT

Figure 4c
6. Carefully remove the silicone where the water
line and wiring pass through the frame rail
(Figure 4b).

Figure 4a
Work Instructions: CSC-2401 Model G Ice Maker Water Line Leak
Revision Level: REV-B
Product: Model G
Page 4 of 8

7. Cut the zip ties holding the blue ice maker
water line to the Flexguard (Figure 6).
FLEXGUARD

9. Open the freezer drawer in the refrigerator and
and remove the freezer tray (Figures 8a and
8b).

ZIP TIES
FREEZER
TRAY

WATER LINE
Figure 6
8. Remove the silicone where the ice maker water
line goes up through the slide-out floor (Figure
7).

Figure 8a

REMOVE
SILICONE

Figure 7
Figure 8b

Work Instructions: CSC-2401 Model G Ice Maker Water Line Leak
Revision Level: REV-B
Product: Model G
Page 5 of 8

10. Use a screw gun and #2 square drive bit to
remove the three (3) screws holding the
refrigerator stile. Set stile and fasteners aside
(Figure 9).

12. Pull the refrigerator as far out of the opening
as possible to access the ice maker water line.
Remove the zip ties holding the ice maker water
lines to the slide out wall (Figure 11).
REMOVE
ZIP TIES

REFRIGERATOR
STILE

Figure 9
11. Remove the handles for the doors and freezer
drawer by pulling them straight up and toward
you (Figure 10). Set handles aside.

Figure 11
13. Disconnect the old water line and transfer the
fitting to the new water line (Figure 12). Tighten
fitting line finger tight into the new waterline,
then use two crescent wrenches to tighen an
additional 1/4 turn.
NEW HOSE

FITTING
Figure 10

OLD HOSE
Figure 12

Work Instructions: CSC-2401 Model G Ice Maker Water Line Leak
Revision Level: REV-B
Product: Model G
Page 6 of 8

14. Attach refrigerator hose to water supply line. Be
sure connection is secure. Attach the RV’s fresh
water system to a regulated compressed air line.
Apply 30 psi of pressure to the system. Spray the
new connections with soapy water. Watch for
bubbles that would indicate a leak (Figure 13).

16. Once pressure testing is complete, push the
refrigerator back into it’s opening and install
the handles (Figure 15).

Figure 15
Figure 13

17. Install the stile holding the refrigerator in place
using the original fasteners (Figure 16).

15. Route the new water line through zip ties
behind the refrigerator (Page 6, Figure 11) and
through the Flexguard supports below the slide
out. Reconnect to the supply line (Figure 14).
Install new zip ties to secure the ice maker water
line to the Flexguard below the slide-out.

ZIP TIES

Figure 16

ZIP TIES

Figure 14

Work Instructions: CSC-2401 Model G Ice Maker Water Line Leak
Revision Level: REV-B
Product: Model G
Page 7 of 8

18. Place the freezer tray back into the freezer
drawer (Page 5, Figure 8a).
19. Use black silicone (part #101006) to seal the
water line at the openings in the frame rail and
slide out floor (Page 4, Figure 4b and Page 5,
Figure 7).
20. Locate heating element wires in the blue
sheathing of the newly installed ice maker
water line. Using two (2) Wago 3-position
connectors, wire the water line heating element
to the closest fresh water tank heat pad wiring
(Figure 17). Wrap the Wago connectors in
electrical tape to hold the levers in place.
21. Test tank heat pad and ice maker water line
heating element for proper operation by using
a clamp-on meter to ensure they are receiving
power, or by turning the heat pads on for 30
minutes to make sure they are heating.

Power Source
+

Ice maker water line
Freshwater Holding
Tank Heat Pad

Figure 17

22. After confirming proper operation of the heating pads and ice maker water line heating element, install
underbelly, fresh water tank drain valves, and sewer hose storage tube (Figure 18).

Figure 18

Work Instructions: CSC-2401 Model G Ice Maker Water Line Leak
Revision Level: REV-B
Product: Model G
Page 8 of 8