In situations where Autosteer is temporarily unavailable, the Autosteer icon disappears. For example, your driving speed is not
within the speed required for Autosteer to operate. Autosteer may also be unavailable if it is not receiving adequate data from
the camera(s).
NOTE: In low light conditions (dusk or dark), Autosteer aborts or is unavailable if headlights are set to Off. For best results, set
headlights to Auto.
If unable to detect lane markings, Autosteer may determine the driving lane based on a vehicle you are following. In these
situations, the vehicle in front of you is highlighted in blue.
In most cases, Autosteer attempts to center CybertruckModel SModel X in the driving lane. However, there may be situations
in which Autosteer may steer CybertruckModel SModel X in a driving path that is offset from the center of the lane (for
example, detection of guard rails).
WARNING: Autosteer is not designed to, and will not, steer CybertruckModel SModel X around objects partially in a
driving lane and in some cases, may not stop for objects that are completely blocking the driving lane. Always watch the
road in front of you and stay prepared to take immediate action. It is the driver's responsibility to be in control of
CybertruckModel SModel X at all times.
Restricted Speed

On a controlled-access highway, the cruising speed reflects the speed limit, taking into consideration any offset you've
specified using Speed Assist. However, if you choose to use Autosteer on residential roads, a road without a center divider, or
a road where access is not limited, Autosteer may limit the maximum allowed cruising speed and the instrument panel displays
a message indicating that speed is restricted. The restricted speed will be the speed limit of the road plus 5 mph (10 km/h).
In situations where the speed limit cannot be detected when Autosteer is engaged, Autosteer reduces your driving speed and
limits the set cruising speed to 45 mph (70 km/h). Although you can manually accelerate to exceed the limited speed,
CybertruckModel SModel X may not brake for detected obstacles. Autosteer slows down to the limited speed when you
release the accelerator pedal. When you leave the road, or disengage Autosteer by using the steering wheelsteering yoke (or
steering wheel), you can increase your set speed again, if desired.
Hold Steering WheelSteering Yoke (or Steering Wheel)

Autosteer determines how best to steer assist in steering CybertruckModel SModel X. When active, Autosteer requires you to
hold the steering wheelsteering yoke (or steering wheel). If it does not detect your hands on the steering wheelsteering yoke
(or steering wheel) for a period of time, a flashing light appears along the top of the instrument panel and the following
message displays:

354

Owner's Manual

Owners Manual
Apply slight turning force to steering wheel

Autosteer detects your hands by recognizing slight resistance as the steering wheelsteering yoke (or steering wheel) turns, or
from you manually turning the steering wheelsteering yoke (or steering wheel) very lightly (without enough force to take over
steering). Autosteer also qualifies your hands as being detected if you engage a turn signal use the Autopilot stalk, or use a
button or scroll wheel on the steering wheelsteering yoke (or steering wheel).
NOTE: When your hands are detected, the message disappears and Autosteer resumes normal operation.
Autosteer requires that you pay attention to your surroundings and remain prepared to take control at any time. If Autosteer
still does not detect your hands on the steering wheelsteering yoke (or steering wheel), the flashing light on the instrument
panel increases in frequency and a chime sounds.
If you repeatedly ignore Autosteer's prompts to apply slight force to the steering wheelsteering yoke (or steering wheel),
Autosteer disables for the rest of the drive and displays the following message requesting you to drive manually. If you don't
resume manual steering, Autosteer sounds a continuous chime, turns on the warning flashers, and slows the vehicle to a
complete stop.
Autopilot unavailable for current drive. Autopilot Strikeout - Attention warnings ignored.

For the rest of the drive, you must steer manually. Autosteer is available again on your next drive (after you stop and shift
CybertruckModel SModel X into Park).
Autopilot Suspension

Use of Autopilot features will be suspended if improper usage is detected.
Use of Autosteer and Full Self-Driving (Supervised) is suspended for a week when you or another driver of your vehicle
receives fivethree Autopilot "strikeouts." A strikeout is when the Autopilot system disengages for the remainder of a trip after
the driver receives several audio and visual warnings for inattentiveness.
You can see how many strikeouts are remaining before Autopilot access is suspended by touching Controls > Autopilot.
A strikeout is forgiven after 7 days, as long as you don't receive another strikeout in that time.
NOTE: If your access to Autosteer and Full Self-Driving (Supervised) is suspended, you also lose access to Autopark.
However, you can still use Traffic-Aware Cruise Control and all active safety features are still enabled.
There may be occasions where driver intervention is required and you must take over immediately to maintain safe driving.
Driver-initiated disengagements do not count as improper usage and are expected from the driver.
Take Over Immediately

In situations where Autosteer is unable to steer CybertruckModel SModel X, Autosteer sounds a warning chime and displays
the following message on the instrument panel:
Take over immediately

When you see this message, TAKE OVER STEERING IMMEDIATELY.

Owner's Manual

355

Owners Manual
Autosteer is Aborting

In situations where Autosteer is unable to assist in steering CybertruckModel SModel X, Autosteer aborts, sounds a warning
chime, and displays the following message on the instrument panel:
Autosteer is aborting

Canceling Autosteer

Autosteer cancels when:
• You press the brake pedal.
• You start steering manually.
NOTE: If Autopilot Activation is set to Double Pull and Autosteer cancels because you started steering manually, TrafficAware Cruise Control remains active. If Autopilot Activation is set to Single Pull and Autosteer cancels because you started
steering manually, Traffic-Aware Cruise Control also cancels.
• You apply rotational force to the steering wheelsteering yoke (or steering wheel) (even a slight amount).
NOTE: If Autopilot Activation is set to Double Pull and Autosteer cancels because you applied rotational force to the
steering wheelsteering yoke (or steering wheel), Traffic-Aware Cruise Control remains active. If Autopilot Activation is set
to Single Pull and Autosteer cancels because you started steering manually, Traffic-Aware Cruise Control also cancels.
• You push the Autopilot stalk away from you.
• You exceed the maximum speed at which Autosteer operates – 90 mph (150 km/h).
• You shift.
• A door is opened.
• An Automatic Emergency Braking event occurs (see Collision Avoidance Assist on page 406).
When Autosteer cancels, it sounds a chime and the Autosteer icon either turns gray to indicate that Autosteer is no longer
active, or disappears to indicate that it is not currently available.
NOTE: If Autosteer cancels because you started steering manuallyapplied rotational force to the steering wheel, Traffic-Aware
Cruise Control remains active. Disengage Traffic-Aware Cruise Control as you normally would, by pressing the brake pedal or
briefly pushing the Autopilot stalk away from you.
To disable Autosteer so it is no longer available, touch Controls > Autopilot > Autopilot Features > Autosteer (Beta).
Auto Lane Change
When Autosteer is active, engage a turn signal to move CybertruckModel SModel X into an adjacent lane (moving the steering
wheelsteering yoke (or steering wheel) would cancel Autosteer).
WARNING: It is the driver's responsibility to determine whether a lane change is safe and appropriate. Auto Lane Change
cannot detect oncoming traffic in the target lane, especially fast moving vehicles from the rear. Therefore, before
initiating a lane change, always check blind spots, lane markings, and the surrounding roadway to confirm it is safe and
appropriate to move into the target lane.
WARNING: Never depend on Auto Lane Change to determine an appropriate driving path. Drive attentively by watching
the road and traffic ahead of you, checking the surrounding area, and monitoring the instrument panel for warnings.
Always be prepared to take immediate action.
WARNING: Do not use Auto Lane Change on roads where traffic conditions are constantly changing and where bicycles
and pedestrians are present.
WARNING: The performance of Auto Lane Change depends on the ability of the camera(s) to recognize lane markings.
WARNING: Do not use Auto Lane Change on winding roads with sharp curves, on icy or slippery roads, or when weather
conditions (such as heavy rain, snow, fog, etc.) may be obstructing the view from the camera(s) or sensors (if equipped).
356

Owner's Manual

Owners Manual
WARNING: Failure to follow all warnings and instructions can result in property damage, serious injury or death.
Operating Auto Lane Change

Auto Lane Change is available whenever Autosteer is active. To change lanes using Auto Lane Change:
1. Perform visual checks to make sure it is safe and appropriate to move into the target lane.
2. Engage the appropriate turn signal, keeping your hands on the steering wheelsteering yoke (or steering wheel).
3. If needed, cancel the turn signal once you are in the target lane.
NOTE: Auto Lane Change cancels if the lane change cannot be completed in five seconds.
NOTE: The minimum speed at which Auto Lane Change operates may vary depending on region, adjacent lane speeds, and
other factors. Always be ready to manually steer and change lanes as necessary.
Auto Lane Change assists in moving moves CybertruckModel SModel X into the adjacent lane in the direction indicated by the
turn signal, provided the following conditions are met:
• The turn signal is engaged.
• Auto Lane Change detected your hands on the steering wheelsteering yoke (or steering wheel).
• CybertruckModel SModel X does not detect a vehicle in its blind spot, or a vehicle or obstacle up to the center of the
target lane.
• Lane markings indicate that a lane change is permitted.
• Midway through the lane change, CybertruckModel SModel X must detect the target lane's outside lane marking. If this
lane marking is not detected, the lane change is aborted and CybertruckModel SModel X returns to its original driving lane.
• The view of the camera(s) is not obstructed.
When an automatic lane change is in progress, Overtake Acceleration is activated, allowing CybertruckModel SModel X to
accelerate closer to a vehicle in front (see Overtake Acceleration on page 348).
NOTE: Auto Lane Change assists in movingmoves CybertruckModel SModel X one lane at a time. Moving into an additional
lane requires you to engage the turn signal a second time after the first lane change is complete.
When using Auto Lane Change, it is important to monitor its performance by watching the driving path in front of you and the
surrounding area. Stay prepared to take over steering at any time. As you are crossing over into the adjacent lane, the
instrument panel displays the location in the lane that CybertruckModel SModel X is moving into.
In situations where Auto Lane Change is unable to operate at optimal performance, or cannot operate due to inadequate data,
the instrument panel displays a series of warnings. Therefore, when using Auto Lane Change, always pay attention to the
instrument panel and be prepared to manually steer CybertruckModel SModel X.

Owner's Manual

357

Owners Manual
Adjacent Lane Speed

When moving significantly faster than vehicles in adjacent lanes, CybertruckModel SModel X automatically reduces the
driving speed. This is especially helpful in heavy traffic situations or when vehicles are constantly merging into different lanes.
When CybertruckModel SModel X detects other vehicles driving significantly slower, the instrument panel highlights the
adjacent lanes with arrows and detected vehicles in gray, and CybertruckModel SModel X reduces the driving speed as
appropriate. To temporarily override this feature, press the accelerator pedal.
WARNING: Never depend on Autopilot to determine a safe driving speed; you are responsible for driving safely and
according to traffic laws in your market region.
Stop Light and Stop Sign Warning
While Autosteer is in use, CybertruckModel SModel X displays a warning on the instrument panel and sounds a chime if it
detects that you are likely to run through a red stop light or stop sign. If this happens, TAKE IMMEDIATE CORRECTIVE ACTION!
The visual and audible warnings cancel after a few seconds, or when you press the brake pedal, whichever comes first.
Stop Light and Stop Sign Warning provides warnings only. It does not slow down or stop CybertruckModel SModel X at red
traffic lights, stop signs, road markings, etc. If equipped with Traffic Light and Stop Sign Control, you can enable this feature
to automatically stop CybertruckModel SModel X at traffic lights and stop signs (see Traffic Light and Stop Sign Control on
page 364).
CAUTION: Stop Light and Stop Sign Warning requires on-board maps to know that a particular stop light or stop sign
exists at a location. In some cases, map data is inaccurate or outdated and may not include all stop lights or stop signs.
Therefore, Stop Light and Stop Sign Warning may not detect all stop lights and stop signs.
WARNING: The Stop Light and Stop Sign Warning feature does not apply the brakes or decelerate
CybertruckModel SModel X and may not detect all stop lights and stop signs. Stop Light and Stop Sign Warning is
designed for guidance purposes only and is not a substitute for attentive driving and sound judgment. Keep your eyes
on the road when driving and never depend on Stop Light and Stop Sign Warning to warn you of a stop light or stop sign.
WARNING: Stop Light and Stop Sign Warning is designed to warn you only when approaching a visible red stop sign,
solid red or later portion of a yellow traffic light. It may not warn you of intersections with flashing lights and it does not
warn you of yield signs or temporary stop and yield signs (such as those used in construction areas). Additionally, Stop
Light and Stop Sign Warning does not warn you of approaching stop lights or stop signs when you are pressing the
accelerator pedal or brake pedal (which disables Autosteer).
Limitations
Autosteer and its associated functions are particularly unlikely to operate as intended when:

358

Owner's Manual

Owners Manual
• Autosteer is unable to accurately determine lane markings. For example, lane markings are excessively worn, have visible
previous markings, have been adjusted due to road construction, are changing quickly (lanes branching off, crossing over,
or merging), objects or landscape features are casting strong shadows on the lane markings, or the road surface contains
pavement seams or other high-contrast lines.
• Visibility is poor (heavy rain, snow, fog, etc.) or weather conditions are interfering with sensor operation.
• A camera(s) or sensor(s) is obstructed, covered, or damaged.
• Driving on hills.
• Approaching a toll booth.
• Driving on a road that has sharp curves or is excessively rough.
• Bright light (such as direct sunlight) is interfering with the view of the camera(s).
• The sensors (if equipped) are affected by other electrical equipment or devices that generate ultrasonic waves.
• A vehicle is detected in your blind spot when you engage the turn signal.
• CybertruckModel SModel X is being driven very close to a vehicle in front of it, which is blocking the view of the camera(s).
WARNING: Many unforeseen circumstances can impair the operation of Autosteer. Always keep this in mind and
remember that as a result, Autosteer may not steer assist in steering CybertruckModel SModel X appropriately. Always
drive attentively and be prepared to take immediate action.

Navigate on Autopilot
NOTE: Navigate on Autopilot is a BETA feature.
When using Autosteer on a controlled-access highway (a main highway on which road users enter and exit using on-ramps
and off-ramps). Navigate on Autopilot guides CybertruckModel SModel X to off-ramps and interchanges based on your
navigation route. Along the highway portion of a navigation route, Navigate on Autopilot also changes lanes to prepare for
exits (route-based lane changes) and to minimize the driving time to your destination (speed-based lane changes).
WARNING: Navigate on Autopilot does not make driving autonomous. You must pay attention to the road, keep your
hands on the steering wheelsteering yoke (or steering wheel) at all times, and remain aware of your navigation route.
WARNING: As is the case with normal driving, be extra careful around blind corners, interchanges, and on-ramps and
off-ramps - obstacles can appear quickly and at any time.
WARNING: Navigate on Autopilot may not recognize or detect oncoming vehicles, stationary objects, and special-use
lanes such as those used exclusively for bikes, carpools, emergency vehicles, etc. Remain alert at all times and be
prepared to take immediate action. Failure to do so can cause damage, injury or death.
Enabling and Customizing Navigate on Autopilot
To enable Navigate on Autopilot, touch Controls > Autopilot > Autopilot Features > Autosteer > Navigate on Autopilot (Beta).
Then, to customize how you want Navigate on Autopilot to operate, touch Customize Navigate on Autopilot:
• Enable At Start Of Every Trip: Choose whether or not you want to automatically enable Navigate on Autopilot for every
navigation route. When enabled, the Navigate on Autopilot button on the turn-by-turn direction list is already enabled at
the start of every trip.
• Speed Based Lane Changes: Navigate on Autopilot is designed to perform both route-based and speed-based lane
changes. Route-based lane changes are designed to keep you on your navigation route (for example, moving you into an
adjacent lane to prepare for an upcoming off-ramp) whereas speed-based lane changes are designed to maintain a driving
speed (not to exceed your cruising speed) that allows you to minimize the time it takes to reach your destination (for
example, moving into an adjacent lane to pass a vehicle in front of you). Speed-based lanes changes are optional. You can
use this setting to disable speed-based lane changes or to specify how aggressively you want Navigate on Autopilot to
change lanes to achieve the set cruising speed. The Mild setting is more conservative about lane changes and may result in
a slightly longer driving time whereas Mad Max is designed to allow you to reach your destination in the shortest driving
time possible, but changes lanes only when safe to do so.
• Exit Passing Lane: Choose whether you want Navigate on Autopilot to maneuver out of a passing lane when navigating to a
destination.

Owner's Manual

359

Owners Manual
NOTE: In addition to route-based and speed-based lane changes, Navigate on Autopilot requests a lane change out of a
passing lane as a reminder to stay in a slower lane when you are not passing other vehicles. Choose NO to disable this and
keep CybertruckModel SModel X in a passing lane except when needed to stay on the navigation route.
• Require Lane Change Confirmation: By default, Navigate on Autopilot requires your confirmation before proceeding with a
lane change by pulling the Autopilot stalk toward you or engaging the appropriate turn signal. However, if you want
Navigate on Autopilot to change lanes without requiring this confirmation, turn this setting off. When you turn the setting
off, you can specify if or how you want to be notified of lane changes (Off, Chime, Vibrate, or Both).
WARNING: If you turn off Require Lane Change Confirmation, Navigate on Autopilot notifies you of upcoming lane
changes and off-ramps, but it remains your responsibility to monitor the environment and maintain control of
CybertruckModel SModel X at all times. Lane changes can occur quickly and suddenly. Always keep your hands on
the wheel and your eyes on the driving path in front of you.
NOTE: The touchscreen displays route-based lane changes at the top of the map's turn-by-turn direction list to notify you that
an upcoming lane change is needed to stay on the navigation route.
Operating Navigate on Autopilot
Once enabled, the Navigate on Autopilot button appears on the map’s turn-by-turn direction list whenever a navigation route
is active and the route includes at least one controlled-access highway. When enabled, the Navigate on Autopilot button is
blue and the turn-by-turn direction displays the Autosteer icon next to the maneuvers (such as off-ramps) that Navigate on
Autopilot will handle.
The Navigate on Autopilot icon shows in the turn-by-turn direction list when you are navigating to a destination
and Navigate on Autopilot is available but not active.

If Navigate on Autopilot is active, the icon is blue. If Enable at Start of Every Trip is turned on, the Navigate on
Autopilot icon is selected whenever you start navigation. Touch the icon to cancel Navigate on Autopilot and
revert to Autosteer. If Enable At Start Of Every Trip is turned off, you must touch the Navigate on Autopilot
button to enable it for each navigation route.

Navigate on Autopilot activates and deactivates as appropriate, based on the type of road you are driving on. For example, if
Autosteer is active and Navigate on Autopilot is enabled, Navigate on Autopilot automatically becomes active when you reach
a controlled-access highway on your navigation route.
Whenever Navigate on Autopilot is active, the instrument panel displays the driving lane as a single blue line in front of
CybertruckModel SModel X:

360

Owner's Manual

Owners Manual

When Navigate on Autopilot is active and you approach an off-ramp or interchange along your navigation route, the
appropriate turn signal engages and Autosteer maneuvers CybertruckModel SModel X onto the off-ramp or interchange.
WARNING: Never depend on Navigate on Autopilot to determine an appropriate lane at an off-ramp. Stay alert and
perform visual checks to ensure that the driving lane is safe and appropriate.
When you leave a controlled-access highway (for example, you take an exit or you enter a section of the navigation route that
is no longer supported), Navigate on Autopilot reverts to Autosteer— a chime sounds and the instrument panel displays the
driving lane lines in blue (instead of the single blue in front of CybertruckModel SModel X).
NOTE: When determining navigation routes, and maneuvers at interchanges, Navigate on Autopilot considers whether or not
you want to use High Occupancy Vehicle (HOV) lanes. Therefore, ensure the Use HOV Lanes setting is appropriate for your
circumstances (see Maps and Navigation on page 443). If the setting is off, Navigate on Autopilot never uses a HOV lane,
regardless of time of day. If the setting is on, Navigate on Autopilot uses HOV lanes, whenever applicable.
WARNING: When Navigate on Autopilot deactivates, Autosteer remains active. Always be prepared to take appropriate
action.

Owner's Manual

361

Owners Manual
WARNING: Navigate on Autopilot may not always attempt to exit at an off-ramp or change lanes, even when an exit or
lane change is determined by the navigation route. Always remain alert and be prepared to manually steer onto an offramp, or make a lane change to prepare for, or to exit at, an off-ramp or interchange.
You can cancel Navigate on Autopilot at any time by touching Navigate on Autopilot on the map’s turn-by-turn direction list
(CybertruckModel SModel X reverts to Autosteer), or by canceling Autosteer entirely (see Canceling Autosteer on page 356).
Lane Changes

Navigate on Autopilot changes lanes to either prepare CybertruckModel SModel X for an upcoming off-ramp, to increase your
driving speed (not to exceed your set cruising speed), or to move CybertruckModel SModel X out of a passing lane when you
are not actively passing other road users. A message displays at the top of the map's turn-by-turn direction list to notify you
when an upcoming lane change is required to stay on your navigation route. The instrument panel displays the upcoming
driving path:

When the instrument panel displays a message asking you to confirm the lane change, engage the appropriate turn signalor
pull the Autopilot stalk toward you. If you do not confirm the lane change within three seconds, a chime sounds to remind you
that Navigate on Autopilot requires your confirmation to change lanes.
If Require Lane Change Confirmation is turned off, Navigate on Autopilot engages the appropriate turn signal, checks for
vehicles and objects, and when appropriate, maneuvers CybertruckModel SModel X into the adjacent lane.
If Require Lane Change Confirmation is turned on, you must engage the appropriate turn signal or pull the Autopilot stalk
toward you to confirm that you want Navigate on Autopilot to proceed with the lane change. If you do not confirm the lane
change within three seconds, a chime sounds to remind you that Navigate on Autopilot requires your confirmation to change
lanes.
NOTE: If you ignore a route-based lane change suggestion (for example, you are driving in the left lane while approaching an
off-ramp on the right side of the highway), Navigate on Autopilot is unable to maneuver onto the off-ramp and as a result, you
are re-routed to your destination.
362

Owner's Manual

Owners Manual
WARNING: Navigate on Autopilot may not always attempt to exit at an off-ramp or change lanes, even when an exit or
lane change is determined by the navigation route. Always remain alert and be prepared to manually steer onto an offramp, or make a lane change to prepare for, or to exit at, an off-ramp or interchange.
Be Ready to Assist

When attempting to change lanes or maneuver CybertruckModel SModel X, or when approaching construction zones,
Navigate on Autopilot may be unable to determine the appropriate driving lane (for example, complex clover leafs and multilane off-ramps) and the instrument panel displays an alert indicating that Navigate on Autopilot is trying to maneuver and may
require assistance. When you see the message, be prepared to take immediate action to ensure that it is safe and appropriate
to complete the lane change or maneuver.

Owner's Manual

363

Owners Manual
Traffic Light and Stop Sign Control
NOTE: Traffic Light and Stop Sign Control is a BETA feature and works best on roads that are frequently driven by Tesla vehicles.
Traffic Light and Stop Sign Control attempts to stop at all traffic lights and may also stop at green lights.
Traffic Light and Stop Sign Control is designed to recognize and respond to traffic lights and stop signs, slowing
CybertruckModel SModel X to a stop when using Traffic-Aware cruise control or Autosteer. This feature uses the vehicle's
forward-facing cameras, in addition to GPS data, and slows the car for all detected traffic lights, including green, blinking
yellow, and off lights in addition to stop signs and some road markings. As CybertruckModel SModel X approaches an
intersection, the instrument clustertouchscreen displays a notification indicating the intention to slow down. You must confirm
that you want to continue or CybertruckModel SModel X stops at the red line displayed on the instrument
clustertouchscreen's driving visualization.
WARNING: NEVER make assumptions and predict when and where Traffic Light and Stop Sign Control will stop or
continue through an intersection or road marking. From a driver's perspective, the behavior of Traffic Light and Stop
Sign Control may appear inconsistent. Always pay attention to the roadway and be prepared to take immediate action. It
is the driver's responsibility to determine whether to stop or continue through an intersection. Never depend on Traffic
Light and Stop Sign Control to determine when it is safe and/or appropriate to stop or continue through an intersection.
Before Using
Before using Traffic Light and Stop Sign Control, you must:
• Ensure that forward-facing cameras are unobstructed (see Cleaning a Camera on page 508Cleaning a Camera on page
773) and calibrated (see Drive to Calibrate Cameras on page 57Drive to Calibrate Cameras on page 773). Traffic Light and
Stop Sign Control depends on the ability of the cameras to detect traffic lights, stop signs, and road markings.
• Ensure that the latest version of maps has been downloaded to CybertruckModel SModel X. Although Traffic Light and
Stop Sign Control primarily uses visual data received from the vehicle's cameras, greater accuracy is achieved when using
the most recent map data. To check which version of maps is currently downloaded, touch Controls > Software. You must
connect to a Wi-Fi network to receive updated maps (see Map Updates on page 450).
• Enable the feature. With the vehicle in Park, touch Controls > Autopilot > Traffic Light and Stop Sign Control. Once enabled,
Traffic Light and Stop Sign Control operates whenever Traffic-Aware Cruise Control or Autosteer is active.
How it Works
When Traffic Light and Stop Sign Control is enabled and you are using Autosteer, Traffic-Aware Cruise Control, or Full SelfDriving (Supervised), the instrument clustertouchscreen displays a popup message to inform you that an upcoming traffic
light, stop sign, or road marking has been detected. As it approaches the stop location, even at an intersection where the traffic
light is green, CybertruckModel SModel X slows down and displays a red line to indicate where CybertruckModel SModel X
will stop. To continue through the intersection—even if the traffic light is green —you must pull the Autopilot stalk toward you
or briefly press the accelerator pedal to give the vehicle permission to proceed. When you've confirmed that you want to
proceed, the red stop line turns gray and CybertruckModel SModel X continues through the intersection and resumes your set
cruising speed.
NOTE: If CybertruckModel SModel X is approaching a green light and detects that a vehicle in front of you is continuing
through the intersection, CybertruckModel SModel X continues through the intersection without requiring your confirmation,
provided you are not in a turning lane and the vehicle can detect that your hands are on the steering wheelsteering yoke (or
steering wheel).
NOTE: If, after you pull the Autopilot stalk toward you or briefly press the accelerator pedal to confirm that you want to
continue through the intersection, the traffic signal changes before you enter the intersection (for example, the light changes
from green to yellow or from yellow to red), CybertruckModel SModel X may determine that it is not appropriate to proceed.
Therefore, CybertruckModel SModel X stops and you must press the accelerator to proceed. At all times, it is your
responsibility to ensure the vehicle stops or accelerates appropriately and safely.
WARNING: Traffic Light and Stop Sign Control DOES NOT turn CybertruckModel SModel X through an intersection
unless Full Self-Driving (Supervised) is engaged. When in a turning lane, CybertruckModel SModel X stops at the red
stop line. To proceed, pull the Autopilot stalk toward you or briefly press the accelerator pedal—
CybertruckModel SModel X continues straight through the intersection (even when in a turning lane), so you MUST
manually steer CybertruckModel SModel X through the intersection (which cancels Autosteer).
Traffic Light and Stop Sign Control is designed to operate as described only when the following conditions are met:

364

Owner's Manual

Owners Manual
• Autosteer, Full Self-Driving (Supervised), or Traffic-Aware Cruise Control is engaged.
• The cameras can detect an upcoming traffic light, stop sign or road marking (for example, cameras are unobstructed and
have a clear line-of-sight to the traffic light, stop sign, or road marking).
• The instrument clustertouchscreen on CybertruckModel SModel X is displaying an upcoming traffic light in "bold" format.
CybertruckModel SModel X does not acknowledge traffic lights that the instrument clustertouchscreen shows as faded. If
a traffic light is not directly ahead of the camera (for example, it is located at an angle of the camera's view, or located in an
adjacent lane) the instrument clustertouchscreen displays it as faded and CybertruckModel SModel X does not slow down
and stop for it.
WARNING: If the instrument clustertouchscreen is not displaying a red stop line at an upcoming intersection,
CybertruckModel SModel X does not slow down or stop. It is the driver's responsibility to pay attention to upcoming
intersections and monitor traffic conditions to determine when and if the vehicle should stop and then to take
appropriate action as needed.
WARNING: Never depend on Traffic Light and Stop Sign Control to determine whether to stop at, or proceed through, an
intersection. Drive attentively by watching the road and paying attention to the roadway, upcoming intersections, traffic
conditions, crosswalks, and other road users. It is always the driver's responsibility to determine whether to stop or
proceed. Be prepared to take immediate action. Failure to do so can result in injury or death.
WARNING: In some situations, Traffic Light and Stop Sign Control may inaccurately detect a traffic light or stop sign,
causing CybertruckModel SModel X to slow down unexpectedly. Be prepared to take immediate action at all times.
WARNING: You must pull the Autopilot stalk toward you or briefly press the accelerator pedal to confirm that you want
to proceed through an intersection, regardless of the status of the traffic light. If you do not confirm,
CybertruckModel SModel X stops at the red stop line displayed on the instrument clustertouchscreen, even if stopping
may be inappropriate. Stopping at a green light may confuse other drivers and may result in a collision, injury or death.
Therefore, always pay attention to upcoming intersections and be prepared to manually brake or accelerate in response
to surroundings.
WARNING: Never assume that your ability to see a traffic light, stop sign, or road marking (especially at a complex
intersection, or an intersection in which a traffic light or sign is partially obstructed, etc.) means that
CybertruckModel SModel X can also see it and respond appropriately.
WARNING: Even the most recent map data does not include all traffic lights and stop signs. Therefore, Traffic Light and
Stop Sign Control relies heavily on the ability of the cameras to detect traffic lights, stop signs, road markings, etc. As a
result, CybertruckModel SModel X may ignore an intersection that is blocked from the camera's view (for example,
obstructed by a tree or a large vehicle or object, or located near a steep hill or sharp curve).
WARNING: Traffic Light and Stop Sign Control is not a substitute for attentive driving and sound judgment.

Owner's Manual

365

Owners Manual
Traffic Lights

When driving with Autosteer or Traffic-Aware Cruise Control engaged, and Traffic Light and Stop Sign Control enabled,
CybertruckModel SModel X is designed to respond as follows when approaching intersections controlled by a traffic light:
Type of Traffic Light

Vehicle Intended Response
At a solid green traffic light, or at a traffic light that is currently off (not illuminated),
CybertruckModel SModel X slows down.
If you are following a car in front of you that continues through the intersection, the
instrument clustertouchscreen displays a green stop line and provided your hands are
detected on the steering wheelsteering yoke (or steering wheel),
CybertruckModel SModel X also continues. If a car is not in front of you, the instrument
clustertouchscreen displays a red stop line and you must confirm that you want to
continue through the intersection by pulling the Autopilot stalk toward you or briefly
pressing the accelerator pedal. If you don’t confirm, CybertruckModel SModel X stops at
the red stop line.
NOTE: CybertruckModel SModel X resumes the set cruising speed when it continues
through the intersection, taking into consideration the speed of a vehicle in front of you.

CybertruckModel SModel X slows down and comes to a complete stop at the red stop
line displayed on the instrument clustertouchscreen. When you want to continue through
the intersection (for example, the light turns green again, or once
CybertruckModel SModel X has come to a complete stop), you must pull the Autopilot
stalk toward you or briefly press the accelerator pedal.

CybertruckModel SModel X slows down and comes to a complete stop at the red stop
line displayed on the instrument clustertouchscreen. When you want to proceed through
the intersection (for example, the light turns green again), you must pull the Autopilot
stalk toward you or briefly press the accelerator pedal.
NOTE: If the traffic light changes after you've confirmed that you want to proceed (for
example, a green traffic light turns yellow), CybertruckModel SModel X may stop instead
of continuing, especially if CybertruckModel SModel X determines that it can safely stop
before entering the intersection.
NOTE: CybertruckModel SModel X is not designed to proceed through an intersection
when the traffic light is red or if the light turns yellow in situations when there is adequate
distance to safely stop before entering the intersection.
NOTE: You can take over driving at any time by manually braking to cancel Autosteer or
Traffic-Aware Cruise Control.

366

Owner's Manual

Owners Manual
Type of Traffic Light

Vehicle Intended Response

CybertruckModel SModel X slows down. To proceed, you must pull the Autopilot stalk
toward you or briefly press the accelerator pedal. If you don’t,
CybertruckModel SModel X stops at the red stop line displayed on the instrument
clustertouchscreen.
NOTE: To prevent CybertruckModel SModel X from stopping, and to minimize how much
it slows down as it approaches, you can confirm that you want to proceed by pulling the
Autopilot stalk toward you or briefly pressing the accelerator pedal at any time after the
instrument clustertouchscreen displays the red stop line. CybertruckModel SModel X
resumes your set cruising speed immediately after you confirm (taking into consideration
the speed of a vehicle in front of you).
WARNING: Approach attentively and be prepared to press the brake pedal to slow
down or stop.

CybertruckModel SModel X slows down and comes to a complete stop at the red stop
line displayed on the instrument clustertouchscreen. When you want to proceed through
the intersection (for example, traffic laws and conditions indicate it is safe and legal to
proceed), you must pull the Autopilot stalk toward you or briefly press the accelerator
pedal.

Owner's Manual

367

Owners Manual
Stop Signs and Road Markings

When driving with Autosteer or Traffic-Aware Cruise Control engaged, and Traffic Light and Stop Sign Control enabled,
CybertruckModel SModel X is designed to respond as follows when approaching intersections controlled by stop signs, stop
lines, or road markings:
Type of Intersection

Vehicle Intended Response
CybertruckModel SModel X assumes the right of way and continues straight without slowing
down or stopping.

No Traffic Control

Arm of T-junction
If CybertruckModel SModel X detects a T-junction based on the map data,
CybertruckModel SModel X slows down and comes to a complete stop at the red stop line
displayed on the instrument clustertouchscreen. When you want to proceed, you must take
over steering and acceleration.
WARNING: CybertruckModel SModel X may not stop at a T-junction that does not have
a stop sign or stop line, or if the T-junction is not included in the map data. Drive
attentively and be prepared to stop (when necessary and/or appropriate).

End of T-junction
CybertruckModel SModel X slows down and comes to a complete stop at the red stop line
displayed on the instrument clustertouchscreen. When you want to proceed through the
intersection, you must pull the Autopilot stalk toward you or briefly press the accelerator
pedal.
NOTE: If you confirm that you want to proceed through an intersection controlled by a stop
sign by pulling the Autopilot stalk toward you or briefly pressing the accelerator pedal before
CybertruckModel SModel X has stopped, your confirmation is ignored.
CybertruckModel SModel X is not designed to proceed through a stop sign without stopping.
NOTE: Even when using Autosteer, and even if you have engaged a turn signal, you must turn
the steering wheelsteering yoke (or steering wheel) yourself (which cancels Autosteer) to
complete a turn at an intersection.
Stop Sign

368

Owner's Manual

Owners Manual
Type of Intersection

Vehicle Intended Response

Stop Sign and Road Marking

Road Marking
WARNING: CybertruckModel SModel X also slows down and stops at a roundabout. You must take over steering (which
cancels Autosteer) and pull the Autopilot stalk toward you or briefly press the accelerator pedal to confirm that you want
to continue through the roundabout.
WARNING: At crosswalks, CybertruckModel SModel X may slow down and may stop, depending on whether the
crosswalk is controlled by a traffic light and whether the cameras detect pedestrians, bicyclists, etc. in the crosswalk.
Pay particular attention at crosswalks and be prepared to take over at any time. Failure to do so can result in injury or
death.
Limitations
Depending on many different circumstances and environmental conditions, Traffic Light and Stop Sign Control may or may not
stop at:
• Railroad crossings.
• Keep-out zones.
• Toll booths.
• Crosswalk systems.
• Yield signs or temporary traffic lights and stop signs (such as at construction areas).
• Miscellaneous traffic U-turn lights, bicycle and pedestrian crossing lights, lane availability lights, etc.
In addition, Traffic Light and Stop Sign Control is particularly unlikely to operate as intended, can disengage, or may not
operate, when one or more of the following conditions are present:
• Driving through consecutive light-controlled intersections that are very close to each other.
• Visibility is poor (heavy rain, snow, fog, etc.) or weather conditions are interfering with camera or sensor operation.
• Bright light (such as direct sunlight) is interfering with the view of the camera(s).
• A camera is obstructed, covered, damaged, or not properly calibrated.
Owner's Manual

369

Owners Manual
• Driving on a hill or on a road that has sharp curves on which the cameras are unable to see upcoming traffic lights or stop