Laser level

Figure 62

Laser line

Front
camera

Laser level
Figure 63

33/71

NTB23-076B

43.

Mark the NISSAN emblem and the floor near the front fascia.

Mark

Mark
Figure 64

44.

Move the laser so it is about 45° and approximately 800 mm (31.5 in.) from the front
of the vehicle, and then line up the vertical laser line to the mark on the NISSAN
emblem.
HINT: The laser level can be either to the left or right of the front of the vehicle.

Mark

Laser
line

Figure 65

34/71

NTB23-076B

45.

Mark the floor with a cross-mark, denoting the center point of the front of the vehicle.

Front
center point

Figure 66

35/71

NTB23-076B

Marking the Center Point for the Rear of the Vehicle
46.

Place the laser level approximately 800 mm (31.5 in.) from the rear of the vehicle and
align the laser with the center mark at the front of the vehicle and the circle in between
the S’s in NISSAN, as shown in Figure 68.

Front center
mark

Laser level

Laser line

Figure 67

Circle

Figure 68

36/71

NTB23-076B

47.

Mark the rear fascia, where shown in Figure 69, and the floor near the rear fascia.

Mark

Mark

Figure 69

48.

Move the laser so it is about 45° and approximately 800 mm (31.5 in.) from the rear of
the vehicle, and then line up the vertical laser line to the mark on the rear fascia.
HINT: The laser level can be either to the left or right of the front of the vehicle.

Mark

Laser
line

Figure 70

37/71

NTB23-076B

49.

Mark the floor with a cross-mark, denoting the center point of the rear of the vehicle.

Rear center
point

Figure 71

38/71

NTB23-076B

Placing Calibration Targets for the Front and/or Rear Cameras
IMPORTANT: Steps 50 - 64 and the related figures show the rear of the vehicle. The front
is similar. If the AVM Control Module was replaced, steps 50 - 64 must be performed for
both the front and rear cameras.
50.

Place the laser level 2500 mm from the rear center point of the vehicle, and then align
the laser line with both the front and rear center points, as shown in Figure 72 and
Figure 73.

Laser line

Front
center point

Laser level
2500
Rear center
point

Laser line

Figure 72

Figure 73
39/71

NTB23-076B

51.

Place a cross-mark on the floor below the laser line (Figure 74).

Cross-mark

Figure 74

40/71

NTB23-076B

52.

Measure and place a mark 500 mm from the rear center point.

500 mm

Mark

Rear center
point

Figure 75

Rear center
point

Mark

Figure 76
41/71

NTB23-076B

53.

Measure and place a mark 2500 mm to the left and to the right of the laser level, as
shown in Figure 77.
Mark

2500 mm
2500 mm

Mark
Figure 77

42/71

NTB23-076B

54.

Move the laser to the 500 mm mark, and then measure and place a mark 2500 mm to
the left and to the right of the laser level, as shown in Figure 78 and Figure 79.

2500 mm
2500 mm

Figure 78

Figure 79

43/71

NTB23-076B

55.

Use a chalk line tool to make a line between the 500 mm and 2500 mm marks, as
shown in Figure 80 and Figure 81.

2500 mm
chalk line
500 mm chalk
line
Figure 80

500 mm chalk
line

2500 mm
chalk line

Figure 81

44/71

NTB23-076B

56.

Place the laser level with both vertical lines activated, and align one laser line with the
500 mm chalk line and align the other laser line to the front and rear center point of
the vehicle, as shown in Figure 82.
IMPORTANT: The laser line must be perfectly aligned with the 500 mm chalk line and
the front and rear center points.

500 mm chalk
line

2500 mm
chalk line

Figure 82
57.

Place a cross-mark on the floor below the laser line (Figure 83).

Cross-mark

Figure 83

45/71

NTB23-076B

58.

Measure and mark 1000 mm increments, as shown in Figure 84 and Figure 85.
500 mm chalk
line
1000mm
1000mm
1000mm
1000mm

2500 mm
chalk line
Figure 84

500 mm chalk
line

Figure 85

46/71

NTB23-076B

59.

Move the laser level to the position shown in Figure 86, and then make a mark on the
2500 mm chalk line, as shown in Figure 86 and Figure 87.
IMPORTANT: The laser line must be perfectly aligned with the 500 mm chalk line.

500 mm chalk
line

2500 mm
chalk line

Mark
Figure 86

500 mm chalk
line

Mark

2500 mm
chalk line

Figure 87

47/71

NTB23-076B

60.

Move the laser level to the position shown in Figure 88, and then make a mark on the
2500 mm chalk line, as shown in Figure 88 and Figure 89.
IMPORTANT: The laser line must be perfectly aligned with the 500 mm chalk line.

Mark

2500 mm
chalk line
500 mm chalk
line
Figure 88

500 mm chalk
line
2500 mm
chalk line
Mark

Figure 89

48/71

NTB23-076B

61.

Using a carpenter’s square, squared to the chalk line, extend each of the seven (7)
marks 12 in. from the chalk line.

Chalk
line

Mark
Carpenter’s
square

Figure 90

500 mm chalk
line

2500 mm
chalk line

Extend these marks

Figure 91

49/71

NTB23-076B

62.

Place five (5) targets on the marks along the 500 mm chalk line.
IMPORTANT: Orient and align the targets, as shown in Figure 92, Figure 93, and
Figure 94. The targets must be aligned with the 500 mm chalk line and the marks
made in step 61 on page 49.

Align

Align

500 mm chalk
line
Align

Mark

Figure 92

Figure 93

Figure 94
50/71

NTB23-076B

63.

Place one (1) target on the driver (LH) side mark on the 2500 mm chalk line.
IMPORTANT: Orient and align the target, as shown in Figure 95, Figure 96, and
Figure 97. The target must be aligned with the 2500 mm chalk line and the marks
made in step 61 on page 49.
Align

Mark

Align

Align

2500 mm
chalk line
Figure 95

Figure 96

Figure 97
51/71

NTB23-076B

64.

Place one (1) target on the passenger (RH) side mark on the 2500 mm chalk line.
IMPORTANT: Orient and align the target, as shown in Figure 98, Figure 99, and
Figure 100. The target must be aligned with the 2500 mm chalk line and the marks
made in step 61 on page 49.
Align

Mark

Align

Align

2500 mm
chalk line
Figure 98

Figure 99

Figure 100
52/71

NTB23-076B

65.

If the front camera was replaced, repeat steps 50 - 64 starting on page 39, to place
the calibration targets for the front camera.

66.

Measure 200 mm and 283 mm from the center point of the driver (LH) side rear
wheel, and then make a mark at each measurement, as shown in Figure 101.

200 mm

283 mm

Figure 101

67.

Measure 200 mm and 283 mm from the center point of the passenger (RH) side rear
wheel, and then make a mark at each measurement, as shown in Figure 102.

283 mm

200 mm

Figure 102
53/71

NTB23-076B

Rear Camera Calibration Measurements
IMPORTANT: All measurements must be in millimeters (mm). Refer to the illustrations in
Figure 107 on page 57 to ensure the correct measurement is documented in the correct
order and for each calibration target.
68.